Just got new LinageOS 14 and found there is no luck to use LTE(T-Mobile).
I tried several methods previous one but still no luck .....
Anyone has better idea to get LTE??????? :fingers-crossed:
Same problem here
I installed Lineage 14 on my N4 with base band **1701.07, I have read many posts but I don't know if it posible to enable LTE with this ROM.
Thanks in advance.
fernando.las said:
I installed Lineage 14 on my N4 with base band **1701.07, I have read many posts but I don't know if it posible to enable LTE with this ROM.
Thanks in advance.
Click to expand...
Click to collapse
You can get unstable LTE on nexus 4 I never got it to work properly you have to flash a hybrid modem/radio zip in a custom recovery to get LTE and make sure build prop is set up for LTE and make sure APN is set up for LTE and make sure ROM supports LTE
I've used at&t and T-Mobile neither seem to work properly with nexus 4 LTE
Idk how else to help have fun trying to get it to work
[email protected] said:
You can get unstable LTE on nexus 4 I never got it to work properly you have to flash a hybrid modem/radio zip in a custom recovery to get LTE and make sure build prop is set up for LTE and make sure APN is set up for LTE and make sure ROM supports LTE
I've used at&t and T-Mobile neither seem to work properly with nexus 4 LTE
Idk how else to help have fun trying to get it to work
Click to expand...
Click to collapse
Does Lineage support LTE?
I have a hybrid radio and I edited the build.prop to enable it and then I set the phone to LTE in the "Phone Info" settings and the APN is set to fast.t-mobile.com, but it just connects to HSDPA anyway.
Related
I have the Canadian Note 3 from Wind Mobile, which runs on AWS network. I was able to get wifi back working after flashing the kernel, but i still can't get 4G back. I tried setting up the APN, but still no go. Does anyone have solution to this?
bump! help please!
tatsu666 said:
I have the Canadian Note 3 from Wind Mobile, which runs on AWS network. I was able to get wifi back working after flashing the kernel, but i still can't get 4G back. I tried setting up the APN, but still no go. Does anyone have solution to this?
Click to expand...
Click to collapse
In which area did the OP of OmegaRom say that the ROM was compatible with the N900W8?
In any case, think about this...
Kernel: Controls system modules like the Wifi ✓
Baseband: Controls the communications between the network and the device. ✖ (try this)
If even flashing the baseband, you don't have your LTE back, then you know what you gotta do.
Hi friends, I am new at this hopefully someone can help me...
I installed the newest version of the goldeneye rom for my Canadian Rogers based S4...
all is running smooth but my LTE is now showing 4g, I checked my APN settings which are 100% fine..
can anyone advise me how to fix this problem..
Thanks
rajan9612 said:
Hi friends, I am new at this hopefully someone can help me...
I installed the newest version of the goldeneye rom for my Canadian Rogers based S4...
all is running smooth but my LTE is now showing 4g, I checked my APN settings which are 100% fine..
can anyone advise me how to fix this problem..
Thanks
Click to expand...
Click to collapse
LTE = 4G. And no is a problem. 4G/LTE (Fourth Generation / Long Term Evolution) is the next stage in mobile network development and provides users with much faster data speeds than 3G is able to. Custom Rom Creator can build 4g icon or LTE icon but its same
I'm trying to get my S4 to LTE only mode so it will accept non whitelisted LTE networks. This used to be possible with an app called "ServiceMode Shortcut", but it seems this is no longer supported in the new rom.
Does any of you know how to get there in 4.4?
88weighed said:
I'm trying to get my S4 to LTE only mode so it will accept non whitelisted LTE networks. This used to be possible with an app called "ServiceMode Shortcut", but it seems this is no longer supported in the new rom.
Does any of you know how to get there in 4.4?
Click to expand...
Click to collapse
Flash ME2 modem mate then , set it up and reflash latest modem once again. Im on 4.4.2 and in order for me to activate HD voice i need to flash mk2 modem and go to dialer and dial those number ie: *#0011# in order to reach HD voice settings and reflash the latest modem
Thanks for the reply.
Does it still work in the GE rom? I don't mind installing that ... I really need it to be easily switchable. I use this phone in a work environment where I also do a lot testing on 2G, 3G and 4G networks. Otherwise I might just downgrade.
88weighed said:
Thanks for the reply.
Does it still work in the GE rom? I don't mind installing that ... I really need it to be easily switchable. I use this phone in a work environment where I also do a lot testing on 2G, 3G and 4G networks. Otherwise I might just downgrade.
Click to expand...
Click to collapse
If your planning to edit something in Servicemode . You need to flash the modem ME2 via odin mate And yes it should work fine .Since Im using a 4.4.2 kitkat
...
Hi,
I did this guide to unlock LTE bands on my Galaxy S5 G900F, but it doesn't work.
Everything in the QXDM is ok and registered after reboot.
Is it because the phone is really made to not support band 4 ? Is there a hardware difference between G900F and G900W8 or this is simply the ROM that activate/desactivate bands ?
By the way, band 4 doesn't exist in NV browser (there are 1/7/13/17/40 bands only). Sounds like a hardware limit, but I want to be sure.
I'm running on Phoenix v7.
Thank you,
Samuel
I'm not posting because I have a solution to your problem. But I just wanted to say that I have the same exact issue. Same hardware, trying to enable the same band too. I've succeeded at writing the correct NV memory value (524511) and it sticks on reboot but the band is still not enabled. Mind you I haven't figured out how to tell which bands are enabled. I'm also running Phoenix Rom V7.
Perhaps we could get some momentum going on this issue.
Did you ever get your phone on Lte band 4?
Sent from my SM-G900F using Tapatalk
Same issue as you
exiledfear said:
Did you ever get your phone on Lte band 4?
Sent from my SM-G900F using Tapatalk
Click to expand...
Click to collapse
Hi exiledfear!
I also have a Galaxy S5 SM-G900F (International version) that I bought in the US last year and want to enable Band 4 so I can use LTE in my country Argentina. I have not attempted to root my phone or write to NV yet, I first want to check whether someone was actually able to get it working using the instructions from http://forum.xda-developers.com/galaxy-s5/general/how-to-add-rf-lte-frequency-bands-to-t2886059
I will really appreciate if you could provide any hints or tips on how to achieve this
Thanks
heres my dilemma
http://forum.xda-developers.com/showpost.php?p=67719294&postcount=29[/url]
Originally Posted by macallik
Having mediocre reception since upgrading to stock MM in USA and I think this could resolve my issues.
The thing is I've never rooted the phone, so I am guessing I have to revert to 5.0.1 and then root the phone and then upgrade to MM and then flash the modem?
Quote:
Originally Posted by famewolf
Well..technically you don't have to be rooted to flash twrp and that's the only requirement to flash the modem zip...the problem you will have is I've heard mobile q is flashing marshmallow for the 6045i now.....so you'd have to flash the panasonic eluga switch software to get back to 5.0.2...flash twrp....then upgrade to mm using one of the rom's in android development so they won't wipe out your twrp. I saw at least one person say the factory rom won't wipe out your twrp either but I wouldn't risk it.
i was in the same boat as macallik, mobileq brought me back to mm so i went the eluga route. after unlocking boot loader and rooting i decided to take a stab at a custom rom. i failed miserably at the installation. so decided to start all over. so i mobileq to mm, then eluga back to 5.0.2, unlock boot loader, root(some steps were redundant). somewhere along the line i lost lte. back mm, no lte. back to 5.0.2, no lte. custom rom(spb2,1), no lte. flasf the 6045i 5.0.2 radio zip, no lte.
is my lte now fubar or is there still hope?
thanks
Click to expand...
Click to collapse
and currently:
famewolf said:
Mobile Q does a full reset of everything...the only reason you would not have lte at that point would be lte not being available in your area or your account not being setup to use it in carrier settings. For example you have to be using the t-mobile lte apn.
Click to expand...
Click to collapse
restored mm through mobileq and still had no lte. used eluga to again go to 5.0.2, flashed a couple different roms both your 6045i radios and nothing. im at a friends house and from sensorly saw that theres a bit of a dead zone through his house. he does have a tmo signal booster and does get lte on his iphone.
any way the radio could be pushed through adb?
any and all suggestions are welcomed. worst case scenario id be forced to upgrade.....
Thanks
rotor nuts said:
heres my dilemma
[/url]
and currently:
restored mm through mobileq and still had no lte. used eluga to again go to 5.0.2, flashed a couple different roms both your 6045i radios and nothing. im at a friends house and from sensorly saw that theres a bit of a dead zone through his house. he does have a tmo signal booster and does get lte on his iphone.
any way the radio could be pushed through adb?
any and all suggestions are welcomed. worst case scenario id be forced to upgrade.....
Thanks
Click to expand...
Click to collapse
Did you do clean installs or are you trying to restore data from old builds? Mobile Q resets ALL the partitions. The flashable radio's overwrite the modem partition. At that point the only factor is whether or not you are using the right config. Are you using the fast.t-mobile.com apn? Did you run the lte discover app to see what towers your phone is actually seeing? Are you comparing the results each time you change the radio? What towers/bands is your friends phone seeing?
If you ran mobile q and you STILL don't have lte then you have other issues..possibly hardware. The eluga software WILL break lte...it's going to install whatever radio the eluga uses and it's not meant for the usa. In another thread I posted how to identify what version radio you are running...that getprop command should work on most models unless you've installed cyanogenmod which wipes out alot of the info from stock.
Example:
1|[email protected]:/ $ getprop | grep non.ver
[ro.tct.non.ver]: [K7SRA0A0BG00]
famewolf said:
Did you run the lte discover app to see what towers your phone is actually seeing? Are you comparing the results each time you change the radio?
Example:
1|[email protected]:/ $ getprop | grep non.ver
[ro.tct.non.ver]: [K7SRA0A0BG00]
Click to expand...
Click to collapse
hadnt ran lte discovery or compared results. ill redo mobileq and see what that yields and try to get the radio version.
ive used both fast.tmobile apns. most have been clean installs. as soon as i get a hold of my friend ill look into his lte bands. installed cm around noon just to give it a try. everything else has been done with mobileq, eluga and mm roms.
lte discovery came up empty. i think my freinds iphone connects to band 4.
thanks
rotor nuts said:
hadnt ran lte discovery or compared results. ill redo mobileq and see what that yields and try to get the radio version.
ive used both fast.tmobile apns. most have been clean installs. as soon as i get a hold of my friend ill look into his lte bands. installed cm around noon just to give it a try. everything else has been done with mobileq, eluga and mm roms.
lte discovery came up empty. i think my freinds iphone connects to band 4.
thanks
Click to expand...
Click to collapse
You should also ensure your phone "mode" in cellular settings is LTE enabled and not set to only wcdma/gsm.
4 is a rather common band used by both AT&T and T-mobile which should work on just about ALL the radio's.
The mode in settings>more>cellular nerwork is set to LTE/wcdma/gsm. I enter a service menu yesterday and where it let you choose radio/service, the only option was wcdma/gsm. Tried tmo sim from iPhone and it only detected 3g/2g but wouldn't connect. So far LTE discovery just sees hspa.
When I get back home I'll try to upgrade with mobileq.
Thanks
I got the same problem like rotor nuts. Restored through mobile q. I did everything that rotor nuts did. Cannot get LTE back. I'm on straight talk att. APN setting are the same one that I always use to get lte. Only getting H network. Before this I was getting around 25 Mbps and now I'll be Lucky to even gets 2 Mbps.
buksua said:
I got the same problem like rotor nuts. Restored through mobile q. I did everything that rotor nuts did. Cannot get LTE back. I'm on straight talk att. APN setting are the same one that I always use to get lte. Only getting H network. Before this I was getting around 25 Mbps and now I'll be Lucky to even gets 2 Mbps.
Click to expand...
Click to collapse
First go into "adb shell" and run the following command..see if you are running the same radio...the N0N0 is the latest radio before the 6.0 version came out.
[email protected]:/ $ getprop | grep non.ver
[ro.tct.non.ver]: [K7SRN0N0BG00]
K7SR = 5.0.2
K7VA = 6.0
then under Settings, More, Cellular Networks, check to make sure your "Preferred Network Mode" is LTE/WCDMA/GSM.
famewolf said:
First go into "adb shell" and run the following command..see if you are running the same radio...the N0N0 is the latest radio before the 6.0 version came out.
[email protected]:/ $ getprop | grep non.ver
[ro.tct.non.ver]: [K7SRN0N0BG00]
K7SR = 5.0.2
K7VA = 6.0
then under Settings, More, Cellular Networks, check to make sure your "Preferred Network Mode" is LTE/WCDMA/GSM.
Click to expand...
Click to collapse
all the setting is correct. my radio version after using mobile q is K7VAUEB0BG00. do you think this might be because of eluga? before i flash eluga my lte was ok but because i wanted to downgrade to get root.
buksua said:
all the setting is correct. my radio version after using mobile q is K7VAUEB0BG00. do you think this might be because of eluga? before i flash eluga my lte was ok but because i wanted to downgrade to get root.
Click to expand...
Click to collapse
As the message you quoted indicates K7VA shows it's the 6045i Marshmallow (6.0) radio which is what mobile Q would install. If that's not your model or you are not on marshmallow then you should find the appropriate radio and flash it. Additionally if you need/want LTE Band 12 then you HAVE to use the 5.0.2 radio as it's been removed from the 6.0 one.
I'm working on a possible hybrid radio but I wouldn't expect it anytime soon. I'm not even in a band 12 area so I'd have to rely on a tester which will slow things down ALOT.
famewolf said:
First go into "adb shell" and run the following command..see if you are running the same radio...the N0N0 is the latest radio before the 6.0 version came out.
[email protected]:/ $ getprop | grep non.ver
[ro.tct.non.ver]: [K7SRN0N0BG00]
K7SR = 5.0.2
K7VA = 6.0
then under Settings, More, Cellular Networks, check to make sure your "Preferred Network Mode" is LTE/WCDMA/GSM.
Click to expand...
Click to collapse
sorry finally got around to adb.(lets just say that im not as smart as i once thought i was)
[ro.tct.non.ver]: [K7VAUEB0BG00]
everything is set to LTE and LTE discovery app only shows hspa
rotor nuts said:
sorry finally got around to adb.(lets just say that im not as smart as i once thought i was)
[ro.tct.non.ver]: [K7VAUEB0BG00]
everything is set to LTE and LTE discovery app only shows hspa
Click to expand...
Click to collapse
Please see the post right above yours. http://forum.xda-developers.com/showpost.php?p=67751447&postcount=9
If you are in a band 12 lte area that would explain things.