Hello
I have problem with my tablet yoga 2 its an android os
Problem that my volume button is stuck after upgrade framework so every time i reboot tablet it enter recovery mode .... and before couple of days it ask me to upgrade again but i ignored it and i forget recharge it ... and now every time i turn it on it enter to fastboot and stuck there ... i dont know what i should to do so any help
Thanks
Hi friends,
I rooted my yu yureka two days ago. It was working fine and i was still on cyanogen os 12.1 .
I used this thread to root and install cwm recovery.
http://forum.xda-developers.com/yureka/development/tool-one-toolbox-yu-yureka-t3087186
Yesterday I restarted the phone (first reboot since rooting) it powered off and then the yu logo came on screen.
The device vibrates and it is stuck on logo. The logo remains as it is and the notification led is turned red for some time then it is gone.
The vibration is continuous and it would probably not stop till battery gets exhausted. I did not wait that long because i feared permanent damage to the hardware.
I am not able to access recovery. But i am able to get into fastboot mode.
What to do now to restore the device to normal operating conditions?
Is my device bricked?
Note : my device is on official cyanogen version 12.1 all software is original and after rooting i installed only greenify app.
Flash cm12.1 by fastboot method.
yesterday i just locked my boot loader and then i manually restarted the device, it booted till zuk logo and then it vibrated and restated again and then it booted till zuk logo and it restated again. in every 2 sec. device is restating. i tried to shutdown the device but that is also not happening it is just restarting again and again -_- . some more issues :
1. not going into recovery mode
2.not going into fastboot mode
3.not shutting down.
4.not getting detected into pc by adb or any other driver.
5.not getting into qualcomm mode.
i just dont knw what to do i just tried every thing but the phone is restarting again and again :'(
if someone knws what could be the problem and solution then please help me.
i have the same probleme what did you do pls!!!!!
i find it thanks gooooood
http://www.androidbrick.com/lenovo-zuk-phones-qfil-roms-unbrick-guide/
Hello,
I am also facing the same problem
I am not able to open the port .
Can you say me how did you open the Qualcomm HS-USB Qdloader 9008
Help me
hello i'm facing an issue with my zuk z1. I flashed zui 2.5 rom in it through qpst and also unlocked my bootloader and flashed twrp it was just working fine, then i decided to flash the nougat firmware because i was getting some random reboots.
today i flashed a firmware(nougat) for ham and then twrp asked me for reboot i selected reboot and selected system (i usually power it off and then power it on manually) and after that it just started booting up infinite times it just shows a penguin logo for just a fraction of second and automatically reboots in just 2-3 seconds and also vibrated while rebooting
Please help me what should i do ?
Whenever I install COS 12.1, my phone went to bootloop
Phone works fine in Nougat and zui but whenever I install cos via fastboot or twrp, it went to bootloop.
Any solutions???
Also any link for Qfil COS 12.1 room?
Hi there
Just wondering if any others have had the touch screen become unresponsive to touch that persist through reboots and even in twrp
it came back after the 3 or so reboot the first time but it happened again 2 days later today and didn't come back for 20ish min
running AICP 13.1 latest build OOS 5.01 firmware and the latest twrp.
Edit
So i reverted to stock os and recovery same issue happened 3 times to day 30-40 seconds of no touch but it happened again and its been an hour of no touch after restarting many times
so i'm now going to return it to the re-seller to be repaired (hopefully)
Lenovo zuk z1 when powered on shows up cynogen logo and automatically power off until entire charging is over?How to solve it please help
I also faced this problem i would say do qpst and then one by one flash rom upto pie or oreo if u want in sequence.