Perhaps,my Lenovo a6000 plus hard bricked because I have flashed wrong file.not connected with pc ,not charging,not boot into recovery,not showing in pc ,not any movement in my phone
If it is hard bricked then how to solve it.please help me who face this situation.
try this
charge your battery from another source as battery is required as compulsion
you don't need much even 2% of charging is enough for dead flashing
after that install proper drivers on your windows machine for qualcomm devices
and then remove and attach battery to your phone ("if you're sure its charged enough")
it'll get detected as qualcomm mass storage device if it got connected
flash it with QFIL
hope so this will help
Bro,for qfil ,I have prefer many sites and download tools and drivers but on my laptop tolls are unable to install.laptop has windows 7 32 bit.when bricked 30 per. Beetery available,the problem is that phone is not responding with pc.so give me link for drivers and tools .I see also some videos and follow links for download but all links are not working.if possible then please help me
I installed qfil and Qualcomm drivers but device not connected and port is nil
Not connected port ,how to solve bro
Anyone guide me please.
https://forum.xda-developers.com/lenovo-a6000/how-to/guide-hard-brick-lenovo-a6000-t3581892
Email me at [email protected] i will give u full guide
lathiyamayur789 said:
Perhaps,my Lenovo a6000 plus hard bricked because I have flashed wrong file.not connected with pc ,not charging,not boot into recovery,not showing in pc ,not any movement in my phone
If it is hard bricked then how to solve it.please help me who face this situation.
Click to expand...
Click to collapse
Your phone is vibrating continously?
No bro,not anyovement
anhh Happened with me use short point method its magical @bugerxXx will help you getting you device alive
I don't understand on page you suggest ,how it is use
I give to Lenovo centre but approx exp .5000
One method is open mobile and 2 points of processor ,touch with copper wire
It works in Lenovo?
Please help me
Not any post regarding hard bricked in bugarxxx
sorry for late reply
didn't got any mail from xda
n me too having 32 bit Windows 7 laptop and fixed my lenovo A6000 plus with the same
downloaded simple adb drivers from here
removed phone battery connected it again
connected the phone to laptop
and A6000 plus is shown as Qualcomm mass storage device
opened Qfil flashed ROM
and android is back to normal
hope so it'll help
I use this trick ,the main problem in all tricks mobile is not connected with pc .I installed properly Lenovo a6000 drivers ,Qualcomm drivers ,remove beetery ,connect ,volume press with connect all tricks but still mobile Qualcomm is not detected
My mobile is hard bricked ,in hard bricked no response of mobile .All are saying qfil method but for it Qualcomm device detect is necessary .but in my case not detected
Somebody help me please if possible.
If mobile software bricked then it show Qualcomm device detected but hard bricked not any detection
Not unbrick till
Related
Hi Guys,
Please I am in some serious mess and I need help. i messed up with my bootloader and now my phone seems dead. now here's what happens, the phone is completely dead and does not power on. any time i connect it to pc, it shows under device manager as USB Input device. under the tap 'HUMAN INTERFACE DEVICE (HID) the red light stays on for some time then it goes off. Actually i have all the necessary flash firmwares to kick it back to life, but the issue i am having is, my phone is not being detected by my pc. i installed Gionee drivers from the official webpage but still it won't detect my phone. it always sees my phone as 'USB INPUT DEVICE' i was told it needs to be detected under com port before my flashing sotware can recognize it.
please Help
Steps Parku said:
Hi Guys,
Please I am in some serious mess and I need help. i messed up with my bootloader and now my phone seems dead. now here's what happens, the phone is completely dead and does not power on. any time i connect it to pc, it shows under device manager as USB Input device. under the tap 'HUMAN INTERFACE DEVICE (HID) the red light stays on for some time then it goes off. Actually i have all the necessary flash firmwares to kick it back to life, but the issue i am having is, my phone is not being detected by my pc. i installed Gionee drivers from the official webpage but still it won't detect my phone. it always sees my phone as 'USB INPUT DEVICE' i was told it needs to be detected under com port before my flashing sotware can recognize it.
please Help
Click to expand...
Click to collapse
Follow this.. U shud b alrite..
http://forum.xda-developers.com/showthread.php?t=2735079
Still Not Helpful.
freak_on said:
Follow this.. U shud b alrite..
http://forum.xda-developers.com/showthread.php?t=2735079
Click to expand...
Click to collapse
Thanks for the support, but actually i have already visited the link. right now, the issue is, my device detects as a USB HID DEVICE, instead of the qualcom. i have downloaded all the necessary drivers but still. And the above link said he has no idea how to deal with that.
Steps Parku said:
Thanks for the support, but actually i have already visited the link. right now, the issue is, my device detects as a USB HID DEVICE, instead of the qualcom. i have downloaded all the necessary drivers but still. And the above link said he has no idea how to deal with that.
Click to expand...
Click to collapse
Try repair ur dirvers, next plug ur device with GNQ , bp browser open the file ( firmware ) an chose bp_imagen next try ap+bp emergency is anyway is not working change this option for general dowload ap+bp
try it
Still Not Helpful.
andresplata94 said:
Try repair ur dirvers, next plug ur device with GNQ , bp browser open the file ( firmware ) an chose bp_imagen next try ap+bp emergency is anyway is not working change this option for general dowload ap+bp
try it
Click to expand...
Click to collapse
Still Not Helpful.
andresplata94 said:
Try repair ur dirvers, next plug ur device with GNQ , bp browser open the file ( firmware ) an chose bp_imagen next try ap+bp emergency is anyway is not working change this option for general dowload ap+bp
try it
Click to expand...
Click to collapse
Hi, Thanks for the help but i did that several times, i even formatted my pc re-installed windows, re-installed the gionee drivers and over and over again, i even tried doing this from windows xp, 32bit, 64 bit, windows vista, windows 7, windows 8. and in all of this above mentioned os, anytime i connect my phone, it displays under Human Interface Devices as USB INPUT DEVICE, with the red light flashing. in this mode, GNQ downloader never gets to recognize my phone. Please any help?
:crying:
Same Problem...
Steve, did you solve the problem? If yes, how did you solve it?
I have the same problem with my Blu Life Pure XL, which is a similar phone.
Regards,
Ricardo
Steps Parku said:
Hi, Thanks for the help but i did that several times, i even formatted my pc re-installed windows, re-installed the gionee drivers and over and over again, i even tried doing this from windows xp, 32bit, 64 bit, windows vista, windows 7, windows 8. and in all of this above mentioned os, anytime i connect my phone, it displays under Human Interface Devices as USB INPUT DEVICE, with the red light flashing. in this mode, GNQ downloader never gets to recognize my phone. Please any help?
:crying:
Click to expand...
Click to collapse
freak_on said:
Follow this.. U shud b alrite..
http://forum.xda-developers.com/showthread.php?t=2735079
Click to expand...
Click to collapse
hey.
I have this problem with my e7 ,
could you fix it , please ?
I have the same problem with zte nubia z7max, so its qualcomm issue that has rarely been talked about and I couldn't find any solution to it at all too.
if find one,let me know plzzzz.
thnx
Hi Everyone, In an attempt to fix my bricked device with all necessary flash files and drivers installed perfectly, my device is being detected under 'HUMAN INTERFACE DEVICE' as a 'USB INPUT DEVICE' in device manager, according to what i read, my device is suppose to display or be detected as "qulacom HS-USB qloader 9008" under com port. but that isn't happening, i repaired the drivers, re-installed them, formatted my pc and tried it on fresh windows installation. but still the problem is there. i even tried it on several computers but it still detects as USB INPUT DEVICE under Human Interface Devices in device manager. Now i am stuck here with my device dead for the past two weeks. please any one with an idea how to fix this issue?
i will be deeply grateful. Thanks!!
:crying:
Steps Parku said:
Hi Everyone, In an attempt to fix my bricked device with all necessary flash files and drivers installed perfectly, my device is being detected under 'HUMAN INTERFACE DEVICE' as a 'USB INPUT DEVICE' in device manager, according to what i read, my device is suppose to display or be detected as "qulacom HS-USB qloader 9008" under com port. but that isn't happening, i repaired the drivers, re-installed them, formatted my pc and tried it on fresh windows installation. but still the problem is there. i even tried it on several computers but it still detects as USB INPUT DEVICE under Human Interface Devices in device manager. Now i am stuck here with my device dead for the past two weeks. please any one with an idea how to fix this issue?
i will be deeply grateful. Thanks!!
:crying:
Click to expand...
Click to collapse
follow this
1. join in recovery mode (cwm)
2. go mounts and stroge and format system
3 reboot ur device ( Now the loop is eliminated, just a static imagen )
3. dowload drives, firmware , and QNCG
4. install drivers or repair it
5 when the step 4 is done, plug ur device on elife logo and wait for driver installation(like 10 min)
6 use winrar for descompress the firmware
7open GNQC select bp browser, and search in folder firmware a file called BP_imagen
8 try with genereal mode or emergency mode, and click dowload
i did it, its working
u must have patience dont worry
try it, its working
good luck
Still Not Helpful.
andresplata94 said:
follow this
1. join in recovery mode (cwm)
2. go mounts and stroge and format system
3 reboot ur device ( Now the loop is eliminated, just a static imagen )
3. dowload drives, firmware , and QNCG
4. install drivers or repair it
5 when the step 4 is done, plug ur device on elife logo and wait for driver installation(like 10 min)
6 use winrar for descompress the firmware
7open GNQC select bp browser, and search in folder firmware a file called BP_imagen
8 try with genereal mode or emergency mode, and click dowload
i did it, its working
u must have patience dont worry
try it, its working
good luck
Click to expand...
Click to collapse
Actually my device doesn't even come on for me to do all that you said, i tried repairing drivers and all that but it still detects as USB INPUT DEVICE under HUMAN INTERFACE DEVICES. i need my device to detect as qualcomm device before GNQC downloader can detect it. my issue is very different here. because GNQC can't see my device since my device is not being detected the rightful way after all. i will deeply appreciate the solution. Thanks
did u fix it??
U can fix ? I have the same problem since three weeks and nothing... this a a sh*t... only recognized by HID... In other ocassion before of this, i can flash my Gionee but now i cant:crying:
Another one here who saw how the phone bricked after being flashed with GnQc, now when I plug the Usb on the Pc or with wall charger, the red light keep lit and it seems like it will like this forever. I am thinking of trying to get out the screen and disconnect the battery, seems like the phone is stuck on some strange mode.
Thanks.
This feel that not have solution....
Can any one fix it ?
i also got stuck . have given to gionee care they are unable to figure what was the actuall problem
Steps Parku said:
Actually my device doesn't even come on for me to do all that you said, i tried repairing drivers and all that but it still detects as USB INPUT DEVICE under HUMAN INTERFACE DEVICES. i need my device to detect as qualcomm device before GNQC downloader can detect it. my issue is very different here. because GNQC can't see my device since my device is not being detected the rightful way after all. i will deeply appreciate the solution. Thanks
Click to expand...
Click to collapse
the problem for me is that it have recovery stock english(e3) and i can't do anything...
anyone fixed the problem? i have my gionee bricked....
Sir I have lenovo k4 note marshmallow 6 I want to root it I had downloaded all file or all kept on PC
Mtp USB device not working
Vcom preload driver not working
I connect switch off phone to PC but not detected I got problem with flash tool
Pls help me
Sent from my Lenovo A7010a48 using XDA-Developers mobile app
Im having the same problem phone not getting detected by sp tools or adb tools
Unable to unlock bootloader
I dont think Pc drivers are the issue cuz i have tried every possible drivers, it has something to do with phone
[email protected] said:
Sir I have lenovo k4 note marshmallow 6 I want to root it I had downloaded all file or all kept on PC
Mtp USB device not working
Vcom preload driver not working
I connect switch off phone to PC but not detected I got problem with flash tool
Click to expand...
Click to collapse
On SPFLASH tool.. when everything is ready and your ready to flash the phone "First press DOWNLOAD button in SPFLASH tool ..
Turn off your device.
When it's completely turned off connect with the USB. Done.
Phone will be detected n flashed..
hirencj said:
On SPFLASH tool.. when everything is ready and your ready to flash the phone "First press DOWNLOAD button in SPFLASH tool ..
Turn off your device.
When it's completely turned off connect with the USB. Done.
Phone will be detected n flashed..
Click to expand...
Click to collapse
Thanx
lenovo vibe k4 note problem
Hello please that can help me I am totally lost ... my phone lenovo vibe k4 note after 4 months of normal use ... suddenly I notice that the charge percentage thinks and descends quickly like a crazy Then it loads itself ... and again the pc can not detect it in normal mode or the mode of download (by the method of flash tool) ...helpppppppp :'( :'( :'( :'( :'( :'(
Hi, i am Damian, btw. im total begginer in case smartphone manage and i dont know english very well, so please, be forgiving.
Today i tried to unlock bootloader on my Meizu m2 Note M571H. I was using this tutorial:
I found a problem with the first step: turn off the smartphone and connect to your pc.
When i turned of my device, and connected by usb with pc, then my phone started charging, i heard the windows's sound of connecting device and just after sound of disconnecting. The Flash Tool didnt found my meizu m2 note and nothing happend. I tried to download newer version of flash tool, download the scatter from other website, update a meizu drivers (they were the lastest), restart phone and pc, use other usb port, turn on debbuging mode, root my device etc. I still didnt resolve my problem. Have you any idea what can i do?
And 1 more time - please, be forgiving because of my english.
I would be very thankfull if will you help me.
@edit
I was installing drivers for wrong com Im an idiot.
Hey I'm facing the same problem.. Can you please help me ?
I am facing the same issue, could be the rom version, I am in 6.xx
or Windows 10.
No COM is appearing for me...
No idea how to solve it though, sorry
First of all you have to download mtk vcom drivers,so when you connect your phone,it will appear in sp Flash tool.Then you have to download unlock tools from web.There you have all that is needed for unlocking the bootloader
need to unbrick yureka which is not recognized by PC
not able to unbrick..... tried many methods ....
need help
mobile is charging
keeps on restarting untill the battery is removed
plzzzz help me