Database Users

Bricked Elife E7, Human Interface Device (HID) Detection Help

Hi Everyone, In an attempt to fix my bricked device with all necessary flash files and drivers installed perfectly, my device is being detected under 'HUMAN INTERFACE DEVICE' as a 'USB INPUT DEVICE' in device manager, according to what i read, my device is suppose to display or be detected as "qulacom HS-USB qloader 9008" under com port. but that isn't happening, i repaired the drivers, re-installed them, formatted my pc and tried it on fresh windows installation. but still the problem is there. i even tried it on several computers but it still detects as USB INPUT DEVICE under Human Interface Devices in device manager. Now i am stuck here with my device dead for the past two weeks. please any one with an idea how to fix this issue?
i will be deeply grateful. Thanks!!
:crying:

Steps Parku said:
Hi Everyone, In an attempt to fix my bricked device with all necessary flash files and drivers installed perfectly, my device is being detected under 'HUMAN INTERFACE DEVICE' as a 'USB INPUT DEVICE' in device manager, according to what i read, my device is suppose to display or be detected as "qulacom HS-USB qloader 9008" under com port. but that isn't happening, i repaired the drivers, re-installed them, formatted my pc and tried it on fresh windows installation. but still the problem is there. i even tried it on several computers but it still detects as USB INPUT DEVICE under Human Interface Devices in device manager. Now i am stuck here with my device dead for the past two weeks. please any one with an idea how to fix this issue?
i will be deeply grateful. Thanks!!
:crying:
Click to expand...
Click to collapse
follow this
1. join in recovery mode (cwm)
2. go mounts and stroge and format system
3 reboot ur device ( Now the loop is eliminated, just a static imagen )
3. dowload drives, firmware , and QNCG
4. install drivers or repair it
5 when the step 4 is done, plug ur device on elife logo and wait for driver installation(like 10 min)
6 use winrar for descompress the firmware
7open GNQC select bp browser, and search in folder firmware a file called BP_imagen
8 try with genereal mode or emergency mode, and click dowload
i did it, its working
u must have patience dont worry
try it, its working
good luck

Still Not Helpful.
andresplata94 said:
follow this
1. join in recovery mode (cwm)
2. go mounts and stroge and format system
3 reboot ur device ( Now the loop is eliminated, just a static imagen )
3. dowload drives, firmware , and QNCG
4. install drivers or repair it
5 when the step 4 is done, plug ur device on elife logo and wait for driver installation(like 10 min)
6 use winrar for descompress the firmware
7open GNQC select bp browser, and search in folder firmware a file called BP_imagen
8 try with genereal mode or emergency mode, and click dowload
i did it, its working
u must have patience dont worry
try it, its working
good luck
Click to expand...
Click to collapse
Actually my device doesn't even come on for me to do all that you said, i tried repairing drivers and all that but it still detects as USB INPUT DEVICE under HUMAN INTERFACE DEVICES. i need my device to detect as qualcomm device before GNQC downloader can detect it. my issue is very different here. because GNQC can't see my device since my device is not being detected the rightful way after all. i will deeply appreciate the solution. Thanks

did u fix it??

U can fix ? I have the same problem since three weeks and nothing... this a a sh*t... only recognized by HID... In other ocassion before of this, i can flash my Gionee but now i cant:crying:

Another one here who saw how the phone bricked after being flashed with GnQc, now when I plug the Usb on the Pc or with wall charger, the red light keep lit and it seems like it will like this forever. I am thinking of trying to get out the screen and disconnect the battery, seems like the phone is stuck on some strange mode.
Thanks.

This feel that not have solution....

Can any one fix it ?

i also got stuck . have given to gionee care they are unable to figure what was the actuall problem

Steps Parku said:
Actually my device doesn't even come on for me to do all that you said, i tried repairing drivers and all that but it still detects as USB INPUT DEVICE under HUMAN INTERFACE DEVICES. i need my device to detect as qualcomm device before GNQC downloader can detect it. my issue is very different here. because GNQC can't see my device since my device is not being detected the rightful way after all. i will deeply appreciate the solution. Thanks
Click to expand...
Click to collapse
the problem for me is that it have recovery stock english(e3) and i can't do anything...
anyone fixed the problem? i have my gionee bricked....

Meizu m2 note - Problem with unlocking bootloader / usb problem

Hi, i am Damian, btw. im total begginer in case smartphone manage and i dont know english very well, so please, be forgiving.
Today i tried to unlock bootloader on my Meizu m2 Note M571H. I was using this tutorial:
I found a problem with the first step: turn off the smartphone and connect to your pc.
When i turned of my device, and connected by usb with pc, then my phone started charging, i heard the windows's sound of connecting device and just after sound of disconnecting. The Flash Tool didnt found my meizu m2 note and nothing happend. I tried to download newer version of flash tool, download the scatter from other website, update a meizu drivers (they were the lastest), restart phone and pc, use other usb port, turn on debbuging mode, root my device etc. I still didnt resolve my problem. Have you any idea what can i do?
And 1 more time - please, be forgiving because of my english.
I would be very thankfull if will you help me.
@edit
I was installing drivers for wrong com Im an idiot.

Hey I'm facing the same problem.. Can you please help me ?

I am facing the same issue, could be the rom version, I am in 6.xx
or Windows 10.
No COM is appearing for me...
No idea how to solve it though, sorry

First of all you have to download mtk vcom drivers,so when you connect your phone,it will appear in sp Flash tool.Then you have to download unlock tools from web.There you have all that is needed for unlocking the bootloader

lenovo a6000 plus totally dead.

Perhaps,my Lenovo a6000 plus hard bricked because I have flashed wrong file.not connected with pc ,not charging,not boot into recovery,not showing in pc ,not any movement in my phone
If it is hard bricked then how to solve it.please help me who face this situation.

try this
charge your battery from another source as battery is required as compulsion
you don't need much even 2% of charging is enough for dead flashing
after that install proper drivers on your windows machine for qualcomm devices
and then remove and attach battery to your phone ("if you're sure its charged enough")
it'll get detected as qualcomm mass storage device if it got connected
flash it with QFIL
hope so this will help

Bro,for qfil ,I have prefer many sites and download tools and drivers but on my laptop tolls are unable to install.laptop has windows 7 32 bit.when bricked 30 per. Beetery available,the problem is that phone is not responding with pc.so give me link for drivers and tools .I see also some videos and follow links for download but all links are not working.if possible then please help me

I installed qfil and Qualcomm drivers but device not connected and port is nil
Not connected port ,how to solve bro
Anyone guide me please.

https://forum.xda-developers.com/lenovo-a6000/how-to/guide-hard-brick-lenovo-a6000-t3581892

Email me at [email protected] i will give u full guide

lathiyamayur789 said:
Perhaps,my Lenovo a6000 plus hard bricked because I have flashed wrong file.not connected with pc ,not charging,not boot into recovery,not showing in pc ,not any movement in my phone
If it is hard bricked then how to solve it.please help me who face this situation.
Click to expand...
Click to collapse
Your phone is vibrating continously?

No bro,not anyovement

anhh Happened with me use short point method its magical @bugerxXx will help you getting you device alive

I don't understand on page you suggest ,how it is use

I give to Lenovo centre but approx exp .5000

One method is open mobile and 2 points of processor ,touch with copper wire
It works in Lenovo?

Please help me

Not any post regarding hard bricked in bugarxxx

sorry for late reply
didn't got any mail from xda
n me too having 32 bit Windows 7 laptop and fixed my lenovo A6000 plus with the same
downloaded simple adb drivers from here​
removed phone battery connected it again
connected the phone to laptop
and A6000 plus is shown as Qualcomm mass storage device
opened Qfil flashed ROM
and android is back to normal
hope so it'll help

I use this trick ,the main problem in all tricks mobile is not connected with pc .I installed properly Lenovo a6000 drivers ,Qualcomm drivers ,remove beetery ,connect ,volume press with connect all tricks but still mobile Qualcomm is not detected

My mobile is hard bricked ,in hard bricked no response of mobile .All are saying qfil method but for it Qualcomm device detect is necessary .but in my case not detected
Somebody help me please if possible.

If mobile software bricked then it show Qualcomm device detected but hard bricked not any detection

Not unbrick till

Lenovo K4 not showing on P.C after flashing

Hello Everyone, I have flashed my Lenovo K4 Note with RR 5.8.3 recently, everything went fine thanks to the developers. But my sd card and phone memory won't show in PC after connection through data cable. I tried all the methods in Google of USB driver updating and all, but nothing is working. Please help am not able to transfer files or access my phone in P.C.

Hello my friend
This happened to me too .. try enable usb debugging and oem unlock If it did not work .. try another pc or install new win then install driver and i'm sure it will be work

mahmoudehab said:
Hello my friend
This happened to me too .. try enable usb debugging and oem unlock If it did not work .. try another pc or install new win then install driver and i'm sure it will be work
Click to expand...
Click to collapse
Thanks for the prompt reply. Dude, a not able to find OEM unlock in the Developer Options, earlier it used to be there. And i tried USB debug still not working.

mahmoudehab said:
Hello my friend
This happened to me too .. try enable USB debugging and OEM unlock If it did not work .. try another PC or install new win then install driver and I'm sure it will be work
Click to expand...
Click to collapse
Hey, Bro, I found the solution
1. Goto C:/Windows/INF and search for wpdmtp.inf & right click and install it.
2. Turn on safe mode on your phone and then connect it to PC then remove safe mode.

moi_sudeep said:
Hello Everyone, I have flashed my Lenovo K4 Note with RR 5.8.3 recently, everything went fine thanks to the developers. But my sd card and phone memory won't show in PC after connection through data cable. I tried all the methods in Google of USB driver updating and all, but nothing is working. Please help am not able to transfer files or access my phone in P.C.
Click to expand...
Click to collapse
Brother i think you have missed something. Open developer option and ON USB Debugging. If you connect your phone with PC then by default it will be connected as a charger you have to change it to Transfer Files.
Swipe down your notification pannel and there is a notification of USB touch that and new popup will open to phone and then change it to Transfer Files and you are done. Now you can transfer files.
I uploaded some screenshots to help you better.
Hit like if you think i helped you.

moi_sudeep said:
Hello Everyone, I have flashed my Lenovo K4 Note with RR 5.8.3 recently, everything went fine thanks to the developers. But my sd card and phone memory won't show in PC after connection through data cable. I tried all the methods in Google of USB driver updating and all, but nothing is working. Please help am not able to transfer files or access my phone in P.C.
Click to expand...
Click to collapse
Goto device manager in pc, under portable devices you will find MTP device. Right click and uninstall the driver. A new icon with exclamation mark should appear. Double click on it, installation wizard pops up then click on ' browse my computer for drivers' then you find mtp drivers now install MTP USB Device... Not MTP Device. Just reconnect the phone. And the job is done.

moi_sudeep said:
Hey, Bro, I found the solution
1. Goto C:/Windows/INF and search for wpdmtp.inf & right click and install it.
2. Turn on safe mode on your phone and then connect it to PC then remove safe mode.
Click to expand...
Click to collapse
thanks! its worked for me

Hello please that can help me I am totally lost ... my phone lenovo vibe k4 note after 4 months of normal use ... suddenly I notice that the charge percentage thinks and descends quickly like a crazy Then it loads itself ... and again the pc can not detect it in normal mode or the mode of download (by the method of flash tool) ...

Help, mtk vcom usb error code 10

Can anyone help me on my problem, k4 note not detected on my laptop.. when i insert usb to laptop, k4 note not detected and when i see device manager>usb vcom properties says cannot start error code 10? Pls help me, i want to flash stock on sp flash

edarick said:
Can anyone help me on my problem, k4 note not detected on my laptop.. when i insert usb to laptop, k4 note not detected and when i see device manager>usb vcom properties says cannot start error code 10? Pls help me, i want to flash stock on sp flash
Click to expand...
Click to collapse
Disable driver signature reinforcement if you are on windows 8 or later versions.
Reboot to safe mode.. uninstall all drivers related to the phone.
Reboot to normal mode, install lenovo usb drivers(google it) and you can now install the firmware

akurativinod said:
Disable driver signature reinforcement if you are on windows 8 or later versions.
Reboot to safe mode.. uninstall all drivers related to the phone.
Reboot to normal mode, install lenovo usb drivers(google it) and you can now install the firmware
Click to expand...
Click to collapse
So you got this error too...
My device now detected in adb..but mtp is giving an error..(error code 10) so i cant flash twrp recovery..?

edarick said:
So you got this error too...
My device now detected in adb..but mtp is giving an error..(error code 10) so i cant flash twrp recovery..?
Click to expand...
Click to collapse
Update MTP usb device driver in Windows Device Danager.....

akurativinod said:
Update MTP usb device driver in Windows Device Danager.....
Click to expand...
Click to collapse
i update it but not installing..says failed
i dont know why...but this my device has no rom or stock installed..and recovery gone after i flashing another recovery yesterday

edarick said:
i update it but not installing..says failed
i dont know why...but this my device has no rom or stock installed..and recovery gone after i flashing another recovery yesterday
Click to expand...
Click to collapse
Try it connecting in different usb ports..
In update driver window, there is small check box next to Show compatible driver software for this device. In the list of devices, select MTP device or MTP usb device. Install it and try again..

akurativinod said:
Try it connecting in different usb ports..
In update driver window, there is small check box next to Show compatible driver software for this device. In the list of devices, select MTP device or MTP usb device. Install it and try again..
Click to expand...
Click to collapse
Its ok now thanks for replying... Now my brother device that i say my own is now on stock...

:victory: