So my phone's screen suddenly stops responding to touch, flickers and the display gradually dims to a few horizontal lines.
It spontaneously starts working again, but is still dim and streaked. All the phone buttons are perfectly working however.
I've hard reset the phone, removed the battery and sim and restarted it again but neither made a difference.
This is a German phone, so Samsung US support cannot help in any way. And no, I can't call them in Germany.
You don't have to offer a magic solution, but if you at least know what the cause of the problem is I'll be extremely grateful.
it happened to me just once & gone when i was on marketplace
i don't know why , it just gone .
One of my HD2s (TMOUS) has a touch screen related issue:
Has the usual sometimes fails to respond to touch.
Also the notification window keeps opening without any input.
Also when it does work going into resco images to view through pictures results in image chopped in half & bottom of image displayed on top of screen & top of image displayed on bottom of screen.
running on energy WM6.5.3 & have done for over 18months & no new software or settings have been added for a long while.
Also don't use the power key much as turn off/standby via touch screen button & normally turn on from standby via windows key ...
assume it digi but as have not seen one with these exact symptoms before thought I would post & see if anyone had similar symptoms from digitizer failure !?
Hi everyone,
My phone display is not waking up by double tap or by power button and hence i'm not able to use the phone. Rest of the phone is working fine.
I'll be grateful if somebody could help me out on this issue.Thanks in advance.
Same is the case with me. I was asked to try resetting any changes made in the Performance menu. Try it, this may help.
Sent from my Yu Yureka (AO5510), from the XDA Android App.
Hi there,
Please wait until mods will move this thread to the device specific forum for more relevant answers.
Stand by
suri68 said:
Hi everyone,
My phone display is not waking up by double tap or by power button and hence i'm not able to use the phone. Rest of the phone is working fine.
I'll be grateful if somebody could help me out on this issue.Thanks in advance.
Click to expand...
Click to collapse
Please explain more clearly-
If your phone is not waking up by double tap or by power button, does it wake up on an incoming call ?
How can you say that rest of the phone is working fine ?
YUREKA YU screen blacked out after reducing brightness
My phone display is blacked out after i reduced the brightness bar... can anyone help how to enable the screen
Flash a torch at tip of the phone near the sensor....then you have to be quick to increase the brightness
As someone reported, if you enable automatic brightness and color correction and reduce the brightness to the lowest, the screen would switch off forever. The only way back is a factory reset or restoring an backup.
just managed to fix this
I was in a real hurry yesterday and must have accidentally set brightness to all 0. And then bam..black screen
here's how i fixed it.
Downloaded this: http://droid-at-screen.ribomation.com/installation/
This mirrors the phone screen on pc using the jar file. Needs adb debugging to be enabled and accessible from pc.
Doesnt allow you do send touch inputs though.
Probably other solutions exist, like miracast etc. But the above app was my first try and it worked.
I kept my super awesome OPO next to the yureka, as a reference for screen position.
looking at the yu screen on pc, i activated, logged in to the phone, and then pushed my brightness up. All on a blank display. Also doing the same in parallel on the OPO, for reference point.
And, the yu screen lit up.
(if not this, may have to edit some system files, but didnt work in my trials..or backup device and then factory resent and then restore back)
How to fix screen goes dark after manually setting brightness zero
Almost all users are facing this issue. If you manually move the brightness slider to low (extreme left) the screen goes completely dark. You will not be able to see the screen. I tried it but kept the finger on the slider at all time so that I could move the slider and get the right screen brightness.
If you had manually changed the brightness to low and removed your finger from the slider. You sure are looking at a blank screen though the phone is still active. To fix it you will need to blindly follow these instructions. Your phone screen is dark, you will not see anything, unlock the phone (hope you are using swipe to unblock). Once done use two fingers to swipe from top screen to bottom. Note you will still see a blank screen, now tap and hold the finger in the center screen a slightly above the volume down button line – that is where the brightness slider is. If you don’t see the screen lighting up, tap again around the same area, you will get.
ok
suri68 said:
Hi everyone,
My phone display is not waking up by double tap or by power button and hence i'm not able to use the phone. Rest of the phone is working fine.
I'll be grateful if somebody could help me out on this issue.Thanks in advance.
Click to expand...
Click to collapse
Change rom
Slight clarification
sunny765 said:
Flash a torch at tip of the phone near the sensor....then you have to be quick to increase the brightness
Click to expand...
Click to collapse
This was the exact problem I faced rather than as mentioned every where fix for
Proximity sensor .Tourch solution is the quickest one to resolve it.
In my case I used another smart phone to put light on yureka just there where microphone or message notification led is there.Miraculously it works yureka reflect back then
You bring back normal brightness.Explaining this as original and was too short to
Comprehend easily.
9111710426
Plz off adoptive brightness
Sent from my AO5510 using XDA Free mobile app
Go to Settings>Display.
And turn off the Adaptive Brightness.
suri68 said:
Hi everyone,
My phone display is not waking up by double tap or by power button and hence i'm not able to use the phone. Rest of the phone is working fine.
I'll be grateful if somebody could help me out on this issue.Thanks in advance.
Click to expand...
Click to collapse
Though this issue may have been solved , the problem mostly is the proximity sensor setting. In dialer, dial *#*#7769#*#*.
This is the setting/calibration window. Press start and keep your ear to the sensor. Remember the value and press exit. Mine was 49.
please help me i ve done some mistake in flashing the yureka...i was installing lollipop on yureka by cmd after flash is done i ve disconnected my device after that my phone was not switching on i ve opened it and take the help of some pins inside my phone got detected in pc and charging led was coming...charging sound was also coming...but the display is black it is coming like blue screen and off coming and going please help me to get my phone back
Hi ppl my E7 start giving a few toutch screen problems a few days ago. At fist it start unlocking the screen and opening apps and doing calls on its own when on my pocket what it never did before since i bought him months ago. The when i was playing heartstone the toutch screen become totaly crazy no leting me do any grab and drag options e clicking screen at randow :S After a few turn screen on/off it become ok again.. But after a few minutes it hapend again :S when form tha moment it was never the same.. sometimes stops from responding other can do the drag up action to unlock screen others cant drag items others it just starts clicking like crazy on screen on its own.. Had a few power on/off.. Problems continues.. Had a factory reset problem seem a little better but not much.. juxt stop clicking on its own now but cant do drag actions across full screen. Now i installed a toutch screen test app. Found that a part of the screen is not responding (or is responding really really bad like a dozen pixels only in a finger from top to buttom size area) in a paint test... the lenght of a finger.. from top to bottoum near the middle screen (Landscape mode). Cold it be a software issue on the rom ? i did installed some suspecius software (im rooted) a few times could it have damage the rom or the touch drivers or controls in a way the reseting it wont fix? could installing other rom fix it ? Could it be that the screen got out of calibration or something like that ? or its really an hardware issue ?
if its hardware is it cheaper just to exchance the touch screen since the screen doesnt have a single scrach? Or replacing the touch panel is the expansive part when screen breaks? Please any idea is welcome even if little help. Thx for any answer in advance and sorry for my bad english :S im Portuguese
Hi,
It would be very kind of you if I can get some help here.
My Yu Yureka got a little wet in the rain but was working fine. A little while later when I wasn't in the rain any more I tried to use my phone. The display flickered for a minute or so before it went blank. I dried off the phone and tied restarting the device but I saw a vertical bluish strip before it went blank again. Now whatever I do, the display doesn't show a thing. I can receive calls, listen to all sorts of sounds the phone makes in general, feel the vibrations and even unlock the device while the screen is completely blank.
Could anyone suggest a solution to this? I would be very grateful.
Regards
SM
Your display is dead. There is no reviving it. You have to get a new display assembly.