{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This is only for Huawei P9 Plus (VIE)
Code:
OpenKirin presents unofficial TWRP for stock EMUI 5.x with decryption support.
Intended for usage on stock emui 5.x in combination with unlocked bootloader and
modded boot image with disabled dm-verity (depending on what you want to do).
Code:
[COLOR="red"][B]WARNING:[/B] since 3.1.0-2 update we've enabled image flashing to special partitions -
not just /recovery or /boot partition.
That means your device could be bricked in a few seconds if you do not pay attention
or don't know what you're doing. (Noobs please stay away out of this section!)[/COLOR]
Installation Instructions
Code:
1. Enter fastboot mode on unlocked device
2. flash recovery using the following command: fastboot flash recovery twrp-3.1.1-1-vie.img
3. reboot to recovery!
Rooting Methods
Code:
[B][U]1. Official SuperSU (not just 2.82+)[/U][/B]
1. Ensure you are running stock kernel from b380+
2. Tick the option "Keep vendor partition mounted" inside OpenKirin Settings
3. download and install [URL="www.supersu.com/download"]official SuperSU[/URL]
4. Enjoy!
[B][U]2. Custom SuperSU[/U][/B]
1. Make sure the device running stock EMUI 5.x boot.img
2. flash this modded SuperSU 2.79: [URL="https://drive.google.com/open?id=0BxWP2gF_0Bd_UmQ2Zm9ZRGxBTUE"]download here[/URL]
3. enjoy root :)
[COLOR="red"][B]NOTE:[/B][/COLOR] this is for every device (except kirin 960 based) running emui 5.x without loop support.
[B][U]3. Magisk[/U][/B]
1. ensure you are running a kernel from b380 or later
2. flash magisk
3. enjoy root & safetynet (read note)
[B][COLOR="red"]NOTE:[/COLOR][/B] Magisk Hide is a known problem on Huawei/Honor devices.
Make sure you are not rebooting/turning off your device with Magisk Hide enabled!
You may face a broken fingerprint scanner, do not worry,
simply disable magisk hide and reboot - fps works again!
Downloads
Code:
[LIST]
[URL="https://github.com/OpenKirin/android_device_huawei_vie/releases/download/3.1.1-1/twrp-3.1.1-1-vie.img"][U]download twrp-3.1.1-1-vie.img[/U][/URL]
[/LIST]
FAQ
Code:
Q: What's the code status?
A: 10. June 2017
Q: which P9+ models are supported?
A: every model should be supported.
Q: Can i use this TWRP with decrypted /data?
yes, you can! (have a look at the instructions in FAQ)
Q: Can i install LOS or AOSP based roms with this TWRP?
yes, you can! (please follow the installing procedure in the corresponding rom thread)
Q: Can i install Magisk?
A: Every ROM based upon b380+ kernel should now include proper loop support.
Since 3.1.0-3 you are able to flash Magisk through TWRP (recovery kernel has been updated)
Q: Does official SuperSU work?
A: Yes, even though chainfire included a fix in his upcomming version,
you can use every version of it, just check the "Rooting Instructions" section.
Q: ETAs?
A: No.
Going back from decrypted -> encrypted?
Code:
1. Format /data inside of TWRP
2. Flash eRecovery & Kernel from your currently installed Stock ROM Build
3. Do a factory reset inside of eRecovery
5. Let device boot up
6. Install your current firmware hw_data package & SuperSU using TWRP again
Want to decrypt? No problem.
Code:
1. Format /data inside of TWRP
2. Flash a kernel with forceencrypt disabled
3. bootup your device
Special Thanks
Code:
* [URL="https://forum.xda-developers.com/member.php?u=2335078"]surdu_petru[/URL]
* [URL="https://forum.xda-developers.com/member.php?u=7354786"]XePeleato[/URL]
* [URL="https://forum.xda-developers.com/member.php?u=220328"]paulobrien[/URL]
XDA:DevDB Information
TWRP, Tool/Utility for the Huawei P9 Plus
Contributors
OldDroid, surdu_petru, xepeleato
Version Information
Status: Stable
Created 2017-04-04
Last Updated 2017-06-11
Reserved
any working twrp for emui 4,1 with decryption support?
Thx bro
Thx for this nice work @OldDroid
This twrp works fine and root too....
VIE-L29C185 does it work?
I think model device is convenient. is it correct? I will be happy if you give me information.
goksemozkan said:
I think model device is convenient. is it correct? I will be happy if you give me information.
Click to expand...
Click to collapse
It is working good on my VIE-L29C185B360! Go ahead, use it and enjoy....
Addymore said:
It is working good on my VIE-L29C185B360! Go ahead, use it and enjoy....
Click to expand...
Click to collapse
my friend. What supersu have you uploaded, give a link.
https://forum.xda-developers.com/p9/...t3565703/page4
DL: http://filestore.to/?d=B9J55H6X9F link empty
goksemozkan said:
my friend. What supersu have you uploaded, give a link.
https://forum.xda-developers.com/p9/...t3565703/page4
DL: http://filestore.to/?d=B9J55H6X9F link empty
Click to expand...
Click to collapse
For root, I flashed this supersu for emui5....in twrp provided up! Working like a charm...! Thx to @OldDroid
Addymore said:
For root, I flashed this supersu for emui5....in twrp provided up! Working like a charm...! Thx to @OldDroid
Click to expand...
Click to collapse
Thanks to all my friends, now root and supersu are working perfectly.
And I will definitely enjoy :good::good::good:
Now, start nel custom rom
Works perfectly on VIE-L29C636 , thank you!
Thank you so much man
successfully got TWRP and root on VIE-L29C185
Good job my friend
Hi,
How can I flash twrp in emui 7? I've tryed several tutorials but I can't do it.
Best Regards
SuperTamagochi said:
How can I flash twrp in emui 7? I've tryed several tutorials but I can't do it.
Click to expand...
Click to collapse
Have you unlocked the bootloader?
Hi guys. Sombody help me. How can i flash magisk on my p9 plus, i try many twrp, but everytime i see loop?
New release is up - TWRP 3.1.1-0 for P9 Plus.
Kernel should now support loop from b381 onwards.
Check OP for download link and github for more information!
P9 Plus Releases + Changelog
Regards
I'm sorry for the inconvenience but i forgot to exclude the special directory inside the /data partition during wipe/factory reset.
I've re-uploaded the fixed release, so everyone who had already installed 3.1.1-0 should now re-download and re-install.
Best regards
I'm sorry if this question has been asked somewhere else before, but can I flash an OTA update (extracted .zip) using TWRP, while keeping TWRP and SU?
It's quite bothersome to go back to full-stock, lock the bootloader, run the update, unlock the bootloader and root again, just for a minor update like B360 to B370.
I'm currently on B360 with TWRP 3.1.0 and SuperSU (rooted).
Rupert van da Cow said:
I'm sorry if this question has been asked somewhere else before, but can I flash an OTA update (extracted .zip) using TWRP, while keeping TWRP and SU?
It's quite bothersome to go back to full-stock, lock the bootloader, run the update, unlock the bootloader and root again, just for a minor update like B360 to B370.
I'm currently on B360 with TWRP 3.1.0 and SuperSU (rooted).
Click to expand...
Click to collapse
Hi, I can tell you in advance that NO, at least with an earlier version and that in principle it is only for normal P9.
Actually, you could only install that recovery, but with that I do not know what to tell you.
Anyway, due to the internal form of Huawei updates, they can not be installed since twrp, at least I have not been able to, nor anyone I know.
Sorry for my bad English, I do not know, and I use a translator.
Enviado desde mi VIE-L09 mediante Tapatalk
Related
Hydrogen OS 2.0 for Oneplus x Listed on
http://www.h2os.com/download
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
http://download.h2os.com/oneplus_x/...01_all_201608241640_wipe_86b633e3fbec4d56.zip
Size : 703mb
Downloading...
Flash the ROM zip with OOS recovery
TWRP wont work to flash this rom and wont boot after successful flash
Guide to Install Gapps and Root
Step 1: Install Hydrogen OS with OPX Stock recovery
Step 2: Dont Reboot the device, Reboot to Fastboot
>> Check if your bootloader is Unlocked
>> Grab Bootloader file (emmc_appsboot.mbn) from Hydrogen OS 5.1.1 stock rom
>> Place it in Adb& fastboot folder and flash it via fastboot
fastboot flash aboot emmc_appsboot.mbn
>> Now Type
fastboot reboot-bootloader
>> Now temporarily boot TWRP official recovery for OPX with fastboot
fastboot boot twrp-3.0.2-0-onyx.img
You should be able to boot to TWRP recovery now
If not use fastboot reboot-bootloader again and this time try to flash TWRP
fastboot flash recovery twrp-3.0.2-0-onyx.img and boot to recovery
Step 3: Now See if your mobile is connected to PC as MTP device like if u can access storage files both on pc and mobile to flash Gapps
Step 4: If storage files are acessible by TWRP, just flash Open Gapps Pico version. If you were unable to flash for some reason try adb sideload
>> Remember you shouldnt reboot your mobile now
>> Reboot to bootloader/fastboot again
>> Now copy the emmc_appsboot.mbn (bootloader file) from Hydrogen os android 6.0 version to fastboot folder (make sure you are deleting or replacing the previous bootloader file from Hydrogen os 5.1.1 version) and flash it
fastboot flash aboot emmc_appsboot.mbn
>> Your mobile should boot normally now with working Gapps
Guide to Flash SuperSu
>> Download Kingroot apk and install it. Try it for once or twice you will be able to gain access to root
>> Try Kingroot to supersu method
ScreenShots
This post has already made me happier, lets try it out.
Nice! flashable through twrp?
migueldbr said:
Nice! flashable through twrp?
Click to expand...
Click to collapse
Yep
Harish_Kumar said:
Yep
Click to expand...
Click to collapse
opengapps or banks gapps for android 6.0 working by flashing with twrp also? Sorry for the questions, but they will be also useful to other users=p
migueldbr said:
opengapps or banks gapps for android 6.0 working by flashing with twrp also? Sorry for the questions, but they will be also useful to other users=p
Click to expand...
Click to collapse
I am still downloading this so cant say
for previous h2os open pico worked fine, if u can wait for 10 more min i can give you more about this 6.0 version
Harish_Kumar said:
I am still downloading this so cant say
for previous h2os open pico worked fine, if u can wait for 10 more min i can give you more about this 6.0 version
Click to expand...
Click to collapse
Sure, i will wait. thanks
Careful with flashing through twrp though, if its anything like the oxygen 3 community build, there is a new bootloader included that will break twrp and you will be stuck without access to recovery (and the only way to fix that is to root with kingroot(dont know if it works on h2os though) and then flash recovery with flashify, or flash with fastboot command)
migueldbr said:
Sure, i will wait. thanks
Careful with flashing through twrp though, if its anything like the oxygen 3 community build, there is a new bootloader included that will break twrp and you will be stuck without access to recovery (and the only way to fix that is to root with kingroot(dont know if it works on h2os though) and then flash recovery with flashify, or flash with fastboot command)
Click to expand...
Click to collapse
Yep
I am safe until i have unlocked bootloader
I will revert back to prev 5.1.1 bootloader and flash Oxygen OS 2.0
Harish_Kumar said:
Yep
I am safe until i have unlocked bootloader
I will revert back to prev 5.1.1 bootloader and flash Oxygen OS 2.0
Click to expand...
Click to collapse
Please leave feedback here when you try then. If twrp still works, etc=p.
Thanks in advance!
Harish_Kumar said:
Hydrogen OS 2.0 for Oneplus x Listed on
http://www.h2os.com/download
http://download.h2os.com/oneplus_x/...01_all_201608241640_wipe_86b633e3fbec4d56.zip
Size : 703mb
Downloading...
Click to expand...
Click to collapse
Hi if you flashed it..
Then please provide some screenshots.
farooque7508 said:
Hi if you flashed it..
Then please provide some screenshots.
Click to expand...
Click to collapse
Will be adding screenshots in few minutes in the second post
@migueldbr
TWRP didnt work for flashing this rom
Had to flash with OOS recovery and after that TWRP didnt boot
Its same like OOS 3.1.0 community build
Harish_Kumar said:
Its same like OOS 3.1.0 community build
Click to expand...
Click to collapse
It' s to be expected.
Harish_Kumar said:
@migueldbr
TWRP didnt work for flashing this rom
Had to flash with OOS recovery and after that TWRP didnt boot
Its same like OOS 3.1.0 community build
Click to expand...
Click to collapse
thanks.
Btw does it have vibration feedback when you double tap screen to wake? It was missing from the previous h2os
Pls share change log in english. On the h20s.com only on chinese...
migueldbr said:
thanks.
Btw does it have vibration feedback when you double tap screen to wake? It was missing from the previous h2os
Click to expand...
Click to collapse
nope it doesn't vibrate
If you flash this in OOS recovery like OOS 3, how would you install gapps afterwards?
Omicron Technics
sniper20 said:
If you flash this in OOS recovery like OOS 3, how would you install gapps afterwards?
Omicron Technics
Click to expand...
Click to collapse
Via Google Installer
What about battery life and
Xposed working or not?
Sent from my ONE E1003 using XDA-Developers mobile app
Red Wolf Recovery Project
Red Wolf Recovery is custom recovery based on the TWRP source code with it's own unique features. And one of these features is also support of the MIUI Incremental OTA's! However this thing is slightly more complicated then just downloading of the zip and flashing.. You have to first enable some things for this and flash some another ZIP file etc. So that's reason why i think that it would be nice to create a guide for this. Now let's look at it...
Pre-requisite
Redmi Note 3 - Snapdragon version!
Common sense
Steps
Download latest build of the recovery from here. And correctly follow the installation process.
After the correct installation reboot your device in to the recovery.
Now click on the "Advanced" and then on "Special Actions".
Here enable these checkboxes:
"Support MIUI Incremental OTA" and "Include System in OTA Survival".
Now clean/dirty flash some full MIUI ROM and flash whatever you want after that.
Now reboot your device in to the system.
When you get some update just download it using updater app and let it automatically reboot in to the RedWolf
Now everything is done! RedWolf will automatically install it and reboot back to the system!
After that you don't have to flash full ROM anymore.. Just always wait for the update from updater app and let it automatically reboot in to the RedWolf.
Now you can flash SuperSU or Magisk and incremental OTA's without any hustles. Use the built-in SuperSU/Magisk option for rooting your device.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Frequently Asked Questions
Q. I am getting Error 7 while flashing incremental OTA?
Ans: If you are really sure that you followed the installation process correctly then send us a log or screenshot and we will look at it.
Q. Can I install xposed, Viper, blah blah..?
Ans: Yes! You can install anything but make sure that you use this recovery for flashing the zip files.
Q.This recovery can be used in any ROM?
Ans: Yes! You can use this recovery in any ROM.
ATG Droid said:
Red Wolf Recovery Project
Red Wolf Recovery is custom recovery based on the TWRP source code with it's own unique features. And one of these features is also support of the MIUI Incremental OTA's! However this thing is slightly more complicated then just downloading of the zip and flashing.. You have to first enable some things for this and flash some another ZIP file etc. So that's reason why i think that it would be nice to create a guide for this. Now let's look at it...
Pre-requisite
Redmi Note 3 - Snapdragon version!
Common sense
Steps
Download latest build of the recovery from here. And correctly follow the installation process.
After the correct installation reboot your device in to the recovery.
Now click on the "Advanced" and then on "Special Actions".
Here enable these checkboxes:
"Support MIUI Incremental OTA" and "Include System in OTA Survival".
Now clean/dirty flash some full MIUI ROM and flash whatever you want after that.
Now reboot your device in to the system.
When you get some update just download it using updater app and let it automatically reboot in to the RedWolf
Now everything is done! RedWolf will automatically install it and reboot back to the system!
[SIZE="3! You can use this recovery in any ROM.
Click to expand...
Click to collapse
Its much better than ZCX since once zcx is replaced by official twrp then it requires full wipe so keep up the good job.
What is different from zcx twrp
Sent from my Redmi Note 3 using Tapatalk
Androbots said:
Its much better than ZCX since once zcx is replaced by official twrp then it requires full wipe so keep up the good job.
Click to expand...
Click to collapse
Can I flash this on 2gb ram variant?
lordsh said:
What is different from zcx twrp
Sent from my Redmi Note 3 using Tapatalk
Click to expand...
Click to collapse
Look at the thread in the development section.. Here is the feature list. Anyway the main difference here is that RedWolf is based on the latest TWRP base and it also support AOSP 8.0.0 based ROMs
rohan_45 said:
Can I flash this on 2gb ram variant?
Click to expand...
Click to collapse
Yup
In ZCX the system img file (size more than 1 gb) is stored in sdcard. Do RedWolf also stores the system img file in sdcard ? (for incremental ota updates)
What if i edit build.prop...will i still be able to update incremental updates??
is that really ota update working on it??anyone tested??
umang0712 said:
What if i edit build.prop...will i still be able to update incremental updates??
Click to expand...
Click to collapse
Depends on what will you edit.
I can't save my custom settings, like reverse nav bar, system time etc. It is auto defaulted after every reboot. How can I save them?
Awesome recovery looks great, but I will downgrade to ZCX until the "bad app" checking is fixed.
Thanks.
M RN3 got bootloop . its not booting only mi logo showing what to do pls help fast as it is not my phone !! Its my fathers pls help guys. The device was running miui 8 marshmallow one. I did flashed correctly twrp also boot up but then I selected reboot to system from within twrp and it doesn't boot to system . What to do pls help. No offence to the twrp recovery developer but I need help pls ? Guys
kg hggggg tightly said:
M RN3 got bootloop . its not booting only mi logo showing what to do pls help fast as it is not my phone !! Its my fathers pls help guys. The device was running miui 8 marshmallow one. I did flashed correctly twrp also boot up but then I selected reboot to system from within twrp and it doesn't boot to system . What to do pls help. No offence to the twrp recovery developer but I need help pls ? Guys
Click to expand...
Click to collapse
Dude I got the same problem, download lazyflasher zip file ,flash it through twrp ,and reboot,it worked for me
dudemathai said:
Dude I got the same problem, download lazyflasher zip file ,flash it through twrp ,and reboot,it worked for me
Click to expand...
Click to collapse
Ya i understood so that means that if i want to flash custom rom will i need to flash lazyflasher whenever i flash a custom rom?
kg hggggg tightly said:
Ya i understood so that means that if i want to flash custom rom will i need to flash lazyflasher whenever i flash a custom rom?
Click to expand...
Click to collapse
I don't think you need to flash it when you change roms,what I know is that lazyflasher bypasses miui so that you won't be stuck in bootloop while you flash anything into miui
otyg said:
Awesome recovery looks great, but I will downgrade to ZCX until the "bad app" checking is fixed.
Thanks.
Click to expand...
Click to collapse
What problem are you facing? This recovery seems better and updated than ZCX.
Sent from my Redmi Note 3
can i use magisk with this?
rs168 said:
can i use magisk with this?
Click to expand...
Click to collapse
Yes
is this support with newest miui 9..?
xerocracker said:
is this support with newest miui 9..?
Click to expand...
Click to collapse
Yes
Sent from my Redmi Note 3 using XDA Labs
Unofficial release -TWRP recovery for the Galaxy J3 2017 - SM-J330F/FN/FZ/G/DS EXYNOS 7570
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
TWRP 3.3.1-0 Released
May 22, 2019
TWRP 3.3.1-0 is out now for most currently supported devices.
What's new in 3.3.1-0:
* Fix selinux issues during formatting - dianlujitao
* Various fixes for toybox and toolbox builds - CaptainThrowback and bigbiff
* Flash both A and B partitions when installing a recovery ramdisk - Dees_Troy
* Add option to uninstall TWRP app from /system - Dees_Troy
* Create digest for subpartitions - bigbiff
Want to get notifications when we release new versions of TWRP? Install the TWRP app and select your device!
We need your help! The bulk of TWRP work is done by a handful of people on a volunteer basis. We have pushed most of our device files to our github and we have a gerrit instance. If you have the ability, please help us maintain our official devices and/or add your device to our official device list. Thanks in advance
UPDATE 10/8/2019
TWRP 3.3.1-1 OO/PP build released
Current status: Beta
Update 15/9/2018
TWRP 3.2.3-1 OO build released.
Current status: Stable
Update 27/1/2018
TWRP 3.2.1-1NN build released
Current status: Stable
Update 23/11/2017
TWRP 3.1.1-1 NN build released.
Current status: Stable
Features:
TOUCHSCREEN working
MTP working
ADB working
SEANDROID warning fix
TWRP and Kernel built from latest source
Factory Image flashing(see below)
NTFS support
F2FS support >> To be added
Twrp app support
New feature available in TWRP v3 is system image backup and restore and factory image flashing (see TWRP changelog for details)
Basically this means factory system images from the official firmware can now be flashed with TWRP.
This feature can be found under INSTALL >> INSTALL IMAGE >> select image to flash >> select partition.[/B]
You flash this at your own risk. Please ensure you have the stock ROM to hand downloaded from SAMMOBILE in case of problems. This will trip the knox counter.
Instructions:
NOTE: ON ANDROID 5.1.1> DEVICES IT IS NECESSARY TO GO TO:
Settings -> Developer Options -> OEM unlocking
AND ENABLE OEM UNLOCK FIRST OR YOU MAY ENCOUNTER 'BLOCKED BY FRP LOCK' WHEN FLASHING.
Flash with ODIN in the AP slot.
1. Put your device in DOWNLOAD mode.
2. Uncheck Auto reboot. (NOT REQUIRED FOR INSTALLING TWRP 3.3.1-1)
3. Load the respective file below into the AP slot and hit start.
4. After flashing and ODIN reports PASS immediately reboot to recovery by holding POWER + HOME + VOL DOWN.
As soon as the screen goes blank change to VOL UP whilst still holding POWER + HOME. (NOT REQUIRED FOR INSTALLING TWRP 3.3.1-1, THE DEVICE WILL AUTO BOOT TO RECOVERY)
5. Flash the V3 RMM bypass zip
https://forum.xda-developers.com/showpost.php?p=79745844&postcount=627
NOTE: FAILURE TO FOLLOW THE STEPS ABOVE IMPLICITLY WILL RESULT IN STOCK RECOVERY REPLACING TWRP AT FIRST BOOT AND BECOMING RMM LOCKED FOR 7 DAYS.
I ALSO SUGGEST BACKING UP ANYTHING YOU NEED ON INTERNAL STORAGE. AT SOME POINT YOU MAY EXPERIENCE A 'VERIFICATION FAILED MESSAGE' .
THIS IS NORMAL, BUT WILL REQUIRE THE DATA PARTITION TO BE FORMATTED IN TWRP.
DOWNLOAD:
twrp_3.3.1-1_sm-j330x_13819
twrp_3.2.3-1_j330_13918
twrp_3.2.1-1_sm-j330f_270117
twrp_3.1.1-1_sm-j330f_231117
Nougat Root instructions:
Install latest Magisk release with TWRP:
https://forum.xda-developers.com/apps/magisk/official-magisk-v7-universal-systemless-t3473445
To disable forced encryption, disable dmverity and mount internal storage:
1. Boot to Twrp
2. Format Data partition using FORMAT DATA button under Wipe options.
(Note: This will wipe the internal storage)
3. Check DATA is mountable.
4. Install the boot image patch.
Boot image patch
no-verity-no-encrypt_ashyx
5. Install Magisk(if root is required)
https://forum.xda-developers.com/apps/magisk/official-magisk-v7-universal-systemless-t3473445
6. Reboot
OREO ONLY ROOT INSTRUCTIONS:
1. Install the Root patch kernel with TWRP.
J330F-FN_root_no_sim_patch
NOTE:This is a custom Oreo J330F/FN XXU3BRG3 permissive/enforcing kernel and patch built from source. It makes changes to the system partition also.
What does it do?:
*It installs a custom kernel to fix the no SIM issue when rooting.
*Patches the system to fix WIFI and Bluetooth not turning on when using custom kernels.
*Patches DM-Verity.
*Removes forced encryption and patches /data not able to be mounted (after formatting).
*Removes the SecurityLogAgent nag when using a custom kernel.
2. If you wish to mount /DATA for access to internal storage then FORMAT the /DATA partition.
3. To root install the latest Magisk below.
https://forum.xda-developers.com/apps/magisk/official-magisk-v7-universal-systemless-t3473445
PIE ONLY ROOT INSTRUCTIONS:
To root install latest Magisk below.
https://forum.xda-developers.com/apps/magisk/official-magisk-v7-universal-systemless-t3473445
To disable encryption (mount DATA in TWRP) install the zip below with TWRP:
Disable_Dm-Verity_ForceEncrypt_Quota_08.02.2019
Finally FORMAT /DATA in TWRP.
Reboot.
DEVICE TREE: soon
PLEASE DO *NOT* DIRECT LINK TO THESE FILES. PLEASE LINK TO THIS POST
Credits: Me, my tester @lemlis, Teamwin
Please note I don't own this device and spend a lot of my free time bringing these builds for you to use and benefit from.
FEEDBACK IS APPRECIATED PLEASE.
THANKS.
DONATE ME HERE IF YOU WANT TO BUY ME A BEER OR HIT THE THANKS BUTTON IF I HELPED YOU
UPDATE: Touchscreen fixed
.
Arggghh i feel something goes wrong with my device intead of succesfull installation. Yes i can flash zip and make nandroid backup. But my device not running properly. I can't adjust screen brightness even camera not functioning. Now i'm waiting for full batery charge to flash stock rom & try to flash twrp once again
---------- Post added at 22:19 ---------- Previous post was at 22:16 ----------
Anual said:
Arggghh i feel something goes wrong with my device intead of succesfull installation. Yes i can flash zip and make nandroid backup. But my device not running properly. I can't adjust screen brightness even camera not functioning. Now i'm waiting for full batery charge to flash stock rom & try to flash twrp once again
Click to expand...
Click to collapse
Now my j330g working normally after i flash cf auto root without flashing stock rom. What's the problem??
Anual said:
Arggghh i feel something goes wrong with my device intead of succesfull installation. Yes i can flash zip and make nandroid backup. But my device not running properly. I can't adjust screen brightness even camera not functioning. Now i'm waiting for full batery charge to flash stock rom & try to flash twrp once again
---------- Post added at 22:19 ---------- Previous post was at 22:16 ----------
Now my j330g working normally after i flash cf auto root without flashing stock rom. What's the problem??
Click to expand...
Click to collapse
Probably the version of SuperSu you flashed.
ashyx said:
twrp_3.1.1-1_sm-j330f_231117
Click to expand...
Click to collapse
Thanks.now color in TWRP is blue.Only in screenshot yellow.backup CPEFS is 0 ? with changed recovery.fsab i have CPEFS 8MB
Works all good.
lemlis said:
Thanks.now color in TWRP is blue.Only in screenshot yellow.backup CPEFS is 0 ? with changed recovery.fsab i have CPEFS 8MB
Works all good.
View attachment 4340464View attachment 4340476
Click to expand...
Click to collapse
Seems I didn't include my updated FSTAB in the new build. Corrected, thanks for pointing it out.
ashyx said:
Probably the version of SuperSu you flashed.
Click to expand...
Click to collapse
Yeaa you right..i use super su which remain in my memory card almost 2 years ago ???
Sorry for this offtopic but can anyone post a link of latest firmware for J330G/DS, which doesn't want to grab my money for Fast download speed please? I want to try this recovery but still afraid if something bad happens. Thanks in advance!
@ashyx, thank you so much for this recovery sir! I've been waiting for a recovery for this phone for so long and now it's here! you managed to create this recovery for this phone even without one! I'm impressed sir!
BlackDragonz said:
Sorry for this offtopic but can anyone post a link of latest firmware for J330G/DS, which doesn't want to grab my money for Fast download speed please? I want to try this recovery but still afraid if something bad happens. Thanks in advance!
@ashyx, thank you so much for this recovery sir! I've been waiting for a recovery for this phone for so long and now it's here! you managed to create this recovery for this phone even without one! I'm impressed sir!
Click to expand...
Click to collapse
updato.com
i cant flash super su twrp didn't show the file to flash
File to flash have to be on sd card ?
Help Me
azhar960225 said:
Help Me
Click to expand...
Click to collapse
Police. Fire or ambulance?
I Want root j3 pro 2017..but how
azhar960225 said:
I Want root j3 pro 2017..but how
Click to expand...
Click to collapse
Flash SuperSU or Magisk.
How? To Flash How? Cannot root j3 How to Flash?
7.11 Android...
arabarabow said:
twrp didn't show the file to flash
Click to expand...
Click to collapse
put zip file inside any folder.File to flash have to be in folder
Just done flashing latest build and flashed magisk, all are running fine. Tysm @ashyx !
can anyone help me telephone stuck on logo and i cant do nothing even reboot to twrp @ashyx
arabarabow said:
can anyone help me telephone stuck on logo and i cant do nothing even reboot to twrp @ashyx
Click to expand...
Click to collapse
Boot to TWRP and flash Supersu or Magisk. Use the three button combo.
Can i just use cf auto root to root my phone without installing a recovery? Or it's better to root using this method?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Welcome to Team OpenKirin AOSP Project. Our goal is to provide
a overall stable AOSP experience across all Huawei/Honor phones
utilizing a Kirin SoC and EMUI 8.0 - either updated or shipped.
So far most of the bugs have been fixed and the ROMs are fully usable
as daily driver - and fully Kirin optimized.
This is the device support section for: Huawei P10.
Any bugs found on this device(s) can be reported here, please include proper logs if you encounter any issues.
We support 3 ROMs in total as of now - LineageOS (Unofficial), ResurrectionRemix OS (Official from Beta 2+), OmniRom
You can find all needed guides/roms on our official website: https://openkirin.net
Requirements: basically full stock EMUI 8.0, with stock recovery/ramdisk
Support: Telegram - https://t.me/joinchat/EeDpi02ekfeJSBeaV4eqOw
XDA:DevDB Information
OpenKirin Treble ROMs, ROM for the Huawei P10
Contributors
OldDroid, XePeleato, surdu_petru
ROM OS Version: 8.x Oreo
ROM Kernel: Linux 4.x
ROM Firmware Required: EMUI 8.0
Based On: LineageOS, ResurrectionRemix OS, OmniRom
Version Information
Status: Beta
Created 2018-08-13
Last Updated 2018-08-27
do you know anyway in which i could unlock my bootloader?
JohnnyMwanza said:
do you know anyway in which i could unlock my bootloader?
Click to expand...
Click to collapse
DC Unlocker is the only way to go as Huawei stopped releasing bootloader unlock codes since July 22, 2018.
I installed the Resurrection Remix and Lineage rom on my P10+ (VKY L29) device and both got me the same problem:
When i boot (the boot is successful), Google starts the first configuration. It asks me the language and the visual properties and then i press "next". The screen remains on "Just a second..." for about forever.
I tried format data before and after, tried to install several Treble roms... Everything took me to the same problem.
I tried also to re-install Gapps, but this took me to another problem: the Google First Configuration is totally black.
What should i do?
McEyes said:
I installed the Resurrection Remix and Lineage rom on my P10+ (VKY L29) device and both got me the same problem:
When i boot (the boot is successful), Google starts the first configuration. It asks me the language and the visual properties and then i press "next". The screen remains on "Just a second..." for about forever.
I tried format data before and after, tried to install several Treble roms... Everything took me to the same problem.
I tried also to re-install Gapps, but this took me to another problem: the Google First Configuration is totally black.
What should i do?
Click to expand...
Click to collapse
Its a know glitch, just reboot and try again.
netmaniack said:
Its a know glitch, just reboot and try again.
Click to expand...
Click to collapse
I tried rebooting about 10 times and he always did the same.
Fortunately I figured out how to resolve this hell:
The Google first configuration setup checks the integrity of the ramdisk Partition. I had a custom recovery so obviously the check was not satisfied.
The solution is to flash the stock recovery ramdisk partition (in my case i download The Official update of Huawei p10 Plus and extracted only the ramdisk image).
When i finished the configuration I completed every setup and then I reinstalled the custom recovery again.
McEyes said:
Fortunately I figured out how to resolve this hell:
The Google first configuration setup checks the integrity of the ramdisk Partition. I had a custom recovery so obviously the check was not satisfied.
The solution is to flash the stock recovery ramdisk partition (in my case i download The Official update of Huawei p10 Plus and extracted only the ramdisk image).
When i finished the configuration I completed every setup and then I reinstalled the custom recovery again.
Click to expand...
Click to collapse
If you have properly read the instructions in OpenKirin website, it was clearly stated there that all these ROMs must be installed wirh stock recovery to avoid other issues.
ej8989 said:
If you have properly read the instructions in OpenKirin website, it was clearly stated there that all these ROMs must be installed wirh stock recovery to avoid other issues.
Click to expand...
Click to collapse
True, I've read the disclaimer, but if someone, like me, used to install ROMs with the same warning without any problem (like an AOSP rom on my previous phone, which I installed having the TWRP), maybe he/she would think that there is not so much to worry about.
However, I noticed that there isn't a real "guide" on internet about a workaround of the "Just a sec" problem, so I wrote that message also for who needs a help and does not know about the partition check.
I found a bug on the "display" menu.
When i select a theme (light, dark, or the black switch), the system theme doesn't change at all. Tried to reboot, clear cache and data of SystemUI, nothing changed.
I bypassed this theme issue with Substratum. Didn't get any bug/problem with Substratum.
Device: P10 plus VKY-L29
Rom: Resurrection Remix 6.1.0 - Oreo - 2018.08.18
McEyes said:
I found a bug on the "display" menu.
When i select a theme (light, dark, or the black switch), the system theme doesn't change at all. Tried to reboot, clear cache and data of SystemUI, nothing changed.
I bypassed this theme issue with Substratum. Didn't get any bug/problem with Substratum.
Device: P10 plus VKY-L29
Rom: Resurrection Remix 6.1.0 - Oreo - 2018.08.18
Click to expand...
Click to collapse
for me working normal
how to root ? can i flash normal magisk or need special for huawei device?
doktor29 said:
for me working normal
how to root ? can i flash normal magisk or need special for huawei device?
Click to expand...
Click to collapse
If you use a normal Huawei EMUI system, there is a special treatment which use a special SuperSu zip file.
Also, you can use a Magisk version, always optimized for Huawei. I found the zip variant in a thread in the P10+ section.
If you have the Treble ROM, which is the main topic of the thread, I did this:
Ensured that there were no setups to do;
Re-flashed TWRP;
Installed the normal Magisk zip from TWRP.
Because is not a EMUI system anymore, you can easily install every mod or patch you wish.
Personal note: I tried install SuperSu with the zip, but the app said "binary occupied". Since it did like that before, with the EMUI system, I gave up and I installed Magisk.
Now it works like a charm.
McEyes said:
If you use a normal Huawei EMUI system, there is a special treatment which use a special SuperSu zip file.
Also, you can use a Magisk version, always optimized for Huawei. I found the zip variant in a thread in the P10+ section.
If you have the Treble ROM, which is the main topic of the thread, I did this:
Ensured that there were no setups to do;
Re-flashed TWRP;
Installed the normal Magisk zip from TWRP.
Because is not a EMUI system anymore, you can easily install every mod or patch you wish.
Personal note: I tried install SuperSu with the zip, but the app said "binary occupied". Since it did like that before, with the EMUI system, I gave up and I installed Magisk.
Now it works like a charm.
Click to expand...
Click to collapse
can you link magisk version?
i try many official but i get info "unable to detect boot image"
doktor29 said:
can you link magisk version?
i try many official but i get info "unable to detect boot image"
Click to expand...
Click to collapse
This is the thread:
https://forum.xda-developers.com/p10-plus/development/magisk-p10-p10plus-t3752482
It says is good even for P10.
you must flash it with TWRP
McEyes said:
This is the thread:
https://forum.xda-developers.com/p10-plus/development/magisk-p10-p10plus-t3752482
It says is good even for P10.
you must flash it with TWRP
Click to expand...
Click to collapse
what version of recovery You use ? because still wont work, i have 3.1.1 for oreo
you have dencrypted or encrypted data ? i try to decrypt but still in recovery i dont see anything in data partition
Don't use twrp with openkirin rom's. Join the telegram openkirin group and u will get there all the help u need. U need magisk 16.7 or newer. I don't understand why people still use twrp when is stated so many times that using twrp with openkirin rom's usually leed's to bootlop.
any chance to get rid of this annoying notification of SDCARD after reboot ?
rom ressurection remix
---------- Post added at 09:52 PM ---------- Previous post was at 09:33 PM ----------
antiratar said:
Don't use twrp with openkirin rom's. Join the telegram openkirin group and u will get there all the help u need. U need magisk 16.7 or newer. I don't understand why people still use twrp when is stated so many times that using twrp with openkirin rom's usually leed's to bootlop.
Click to expand...
Click to collapse
so how i can flash magisk without twrp ?
for me it works only data partition is not vivible due to encryption
can someone test fingerprint after reboot ?
i have strange issue, after reboot my fingerprint is not recognized anymore :/
if i add new one is ok till next reboot, then again my FP is not recognizing.
and no i dont mean it wont work berofre i put PIN/Passoword after reboot it wont work at all after reboot till i add next one :/
it happen in RR and Carbon, other roms i dont test
doktor29 said:
can someone test fingerprint after reboot ?
i have strange issue, after reboot my fingerprint is not recognized anymore :/
if i add new one is ok till next reboot, then again my FP is not recognizing.
and no i dont mean it wont work berofre i put PIN/Passoword after reboot it wont work at all after reboot till i add next one :/
it happen in RR and Carbon, other roms i dont test
Click to expand...
Click to collapse
Are you on stock kernel? Does this happen ALL the time or just random?
doktor29 said:
so how i can flash magisk without twrp ?
Click to expand...
Click to collapse
Instructions here: https://forum.xda-developers.com/ho...agisk-root-honor-view-10-mate-10-pro-t3749280
You only need to use fastboot.
ej8989 said:
Are you on stock kernel? Does this happen ALL the time or just random?
Instructions here: https://forum.xda-developers.com/ho...agisk-root-honor-view-10-mate-10-pro-t3749280
You only need to use fastboot.
Click to expand...
Click to collapse
it happen to me every reboot :/
i have only magisk with stock recovery, from instruction above
doktor29 said:
what version of recovery You use ? because still wont work, i have 3.1.1 for oreo
you have dencrypted or encrypted data ? i try to decrypt but still in recovery i dont see anything in data partition
Click to expand...
Click to collapse
I use the FromFutureRom version that is in the thread I linked before. I think is made especially for Huawei P10/P10+
My data partition is still encrypted.
In order to decrypt data you should format the so called "user data", which is the combination of /data and /sdcard. Don't have to say that you will lose everything on your internal archive, so be sure to backup everything. The external SD card will NOT be affected.
In the TWRP you can to this on the menu "format" -> "format data" -> write "yes" and format everything.
---------- Post added at 02:15 PM ---------- Previous post was at 02:14 PM ----------
antiratar said:
Don't use twrp with openkirin rom's. Join the telegram openkirin group and u will get there all the help u need. U need magisk 16.7 or newer. I don't understand why people still use twrp when is stated so many times that using twrp with openkirin rom's usually leed's to bootlop.
Click to expand...
Click to collapse
You are absolutely right, but I said that you can install TWRP or any custom rom AFTER the Treble Rom installation. I am now on Resurrection Remix Treble rom, with a TWRP recovery installed after the rom flash and everything is fine since the first boot.
Completely Re-Written in C#
This version is actually up to date, sorry for the long time between releases, I had to learn c# before creating the C# version...
Anyways, you know the schpeel
I am not responsible for anything that happens to your device, or computer as a result of you using my toolkit. You are responsible for your own devices, don't be stupid.
Please note, this program is in it's early days, due to me not knowing a lot of c#. Please be patient if it is buggy, comment and join my telegram channel for support at https://t.me/a2_gui_toolkit
The features include:
Reboot options
Reboot to EDL mode
Common Links used in the forums
IMG flasher (beta)
Stock rom downloader and flasher (beta)
No install TWRP launcher
No install TWRP zip installer
Auto Root
Auto Update Checker.
Other features to come
Easter egg, can you find it?
Future features
Backup/Restore
Convert to Mi 6X
Mi 6x Support
Rom installer
Hex Kernel Installer
Possible Suggestions
Camera 2 enabler
OTA installer for rooted users
Some screenshots
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Release Notes
Version 1.0.2
Added auto-root functionality
Fixed random crashes and bugs
Added new UI elements for parts currently being worked on
Converted to use a c# adb api
added dropdown for noob mode
updated instructions and order of certain processes
added json support for twrp api (in the future will automatically download latest twrp version)
probably more I am forgetting
Version 1.0.1
fixed TWRP zip flashing on reboot
Fixed settings not saving correctly on certain systems
Fixed many misc bugs
Updated dialogs to be more convienient and guiding
Created disabled butttons to show future implimentations
Added backup via ADB backup, restore is not yet implimented
Please ensure you have .net version 4.6.1 or later! It can be downloaded here if not already installed.
https://dotnet.microsoft.com/download/dotnet-framework/net461
Download Toolkit Here
https://github.com/da-ha3ker/Jarvinator-A2-Toolkit-Release
Can you provide some screenshots or tutorial? Thank you in advance!
Can you provide the same tool for Mi A2 Lite ?
Thank you
8 no. revert to stock rom
if i use this will my bootloader unlocked a2 will revert to stock rom with bootloader locked?
Syed Shahriar said:
8 no. revert to stock rom
if i use this will my bootloader unlocked a2 will revert to stock rom with bootloader locked?
Click to expand...
Click to collapse
No. It will only flash the stock rom, your bootloader will still be unlocked. I will add re-lock bootloader as an option in future updates
Daha3ker said:
No. It will only flash the stock rom, your bootloader will still be unlocked. I will add re-lock bootloader as an option in future updates
Click to expand...
Click to collapse
flash rom with august patch?
and will stock rom be downloaded from the commands ?
No 4 installs the patches boot image right? No 5 install the original one? Do i have to install the unpatched image (unroot) before ota?
bartoloandre98 said:
No 4 installs the patches boot image right? No 5 install the original one? Do i have to install the unpatched image (unroot) before ota?
Click to expand...
Click to collapse
No 4 and 5 is correct. You will have to have an unrooted device to install ota's, so if you run the unroot it should work; So as long as your device's system hasn't been modified (eg busybox or non systemless modifications) you should be good to install the ota.
Syed Shahriar said:
flash rom with august patch?
and will stock rom be downloaded from the commands ?
Click to expand...
Click to collapse
The version is stated in the description. So yes, the August patch. The stock rom is in the Stock_images folder. So it is downloaded when you download the program.
Ahmed_hassan95 said:
Can you provide the same tool for Mi A2 Lite ?
Click to expand...
Click to collapse
I do not have an A2 lite, if you or someone you know would like to, you can port this to the lite version. It should not be too hard, I just don't have any way to test what would work and what would not.
I've my A2 already unlocked (BootLoader unlocked)
if i want simply to root it, have i simply to use 4. Root Device ?
does this install also TWRP ?
have i to launch 4 option with phone in faastboot, or in normal mode ?
webmasterone said:
I've my A2 already unlocked (BootLoader unlocked)
if i want simply to root it, have i simply to use 4. Root Device ?
does this install also TWRP ?
have i to launch 4 option with phone in faastboot, or in normal mode ?
Click to expand...
Click to collapse
You must run OEM unlock, unlock flashing and unlock critical, then run 4 to root the device. TWRP will cause a bootloop, so follow the instructions in option 6 to avoid it. TWRP is able to be used, but not permanetly installed.
No spiking english, how relock bootloader? Help me please!
Nestor0rtiz1 said:
No spiking english, how relock bootloader? Help me please!
Click to expand...
Click to collapse
fastboot oem lock
AhanafTanvir said:
fastboot oem lock
Click to expand...
Click to collapse
Could you explain me please?
Nestor0rtiz1 said:
Could you explain me please?
Click to expand...
Click to collapse
boot to fastboot mode in ur phone, connect via usb, open fastboot from pc. type
fastboot oem lock
tell me what happens
I really want to install GCAM and camera2API on my A2, but also, I don't want to lose OTA updates, banking funcionatility and don't want to keep bootloader unlocked.
Can I have this? Or am I dreaming too high?
kadu20es said:
I really want to install GCAM and camera2API on my A2, but also, I don't want to lose OTA updates, banking funcionatility and don't want to keep bootloader unlocked.
Can I have this? Or am I dreaming too high?
Click to expand...
Click to collapse
You won't lose data when locking the bootloader, only unlocking. You can OTA update, if you open magisk manager and uninstall (restore the original boot.img). I didn't test this myself, but I will as soon as the next OTA is available.
hugopg said:
You won't lose data when locking the bootloader, only unlocking. You can OTA update, if you open magisk manager and uninstall (restore the original boot.img). I didn't test this myself, but I will as soon as the next OTA is available.
Click to expand...
Click to collapse
Cool! When you get done, please, share your experience. If you can, share the process of restoring of the original "boot.img"