Database Users

[Q] Really Bricked?

I had an Asylum Custom Rom installed.
I also had TWRP as the recovery installed.
I decided to try the new COLOR ROM public beta that I got from the OPPO forums.
I went into TWRP recovery, did a full wipe and then proceeded to install the new COLOR ROM.
When I rebooted, the phone never turned on again.
Now I cannot get to fastboot, recovery, or turn on the phone at all.
I browsed through many forums and tried
1. Charging phone for 5 hours (no led light when plugged in) -> nothing
2. Holding Power button for 30 secs, (5 times to try a hard reset) -> nothing
3. Holding Down button for 10 secs -> nothing
4. Power and up volume -> nothing
5. Power and down volume -> nothing
6. Plugged into computer USB and tried all button combos -> nothing
Is my phone really bricked now?

I hope for your sake it really isn't the case. It does seem like you have tried all the usual ways of getting around the symptoms you are describing. It sounds like you had a bad download and flashed it anyway. I hope someone has some advice for you to fix your device. I am currently on Asylum and was just considering trying out the new Color ROM so i think i'll hold off until i know for sure you can resurrect your device.
when you are hooked up to USB on PC can you try ADB? does it even see the device at all?

killerskincanoe said:
I hope for your sake it really isn't the case. It does seem like you have tried all the usual ways of getting around the symptoms you are describing. It sounds like you had a bad download and flashed it anyway. I hope someone has some advice for you to fix your device. I am currently on Asylum and was just considering trying out the new Color ROM so i think i'll hold off until i know for sure you can resurrect your device.
when you are hooked up to USB on PC can you try ADB? does it even see the device at all?
Click to expand...
Click to collapse
Nothing. no response whatsoever. I've worked with many different phones before starting with the Nexus One and I've always been able to get out of a potentially bad situation because I could at least always get to fastboot or recovery, but in this case, nothing. It really is like working with a brick, hence the term "brick". Now i can really understand the meaning of the term.

such a bummer. it certainly makes me think twice about trying other ROMS now jeez

update
Just an update to this thread... I sent my Find 5 to get repaired to try and figure out what the problem was. It turned out that the battery had failed and they replaced the battery for me. Glad to say that my Find 5 is up and running again.

dtwrain said:
Just an update to this thread... I sent my Find 5 to get repaired to try and figure out what the problem was. It turned out that the battery had failed and they replaced the battery for me. Glad to say that my Find 5 is up and running again.
Click to expand...
Click to collapse
good to hear !!
I couldnt really believe that flashing a rom using recovery affects fastboot let alone button combos/charging...
btw what were the costs of replacing the battery ? or was it free of charge under warranty...

dtwrain said:
Just an update to this thread... I sent my Find 5 to get repaired to try and figure out what the problem was. It turned out that the battery had failed and they replaced the battery for me. Glad to say that my Find 5 is up and running again.
Click to expand...
Click to collapse
Glad to hear it turned out that way. Really strange situation.

Oualcomm HS-USB Diagnostics 9008
1) Can you give me some advices? Smartphone OPPO find 5 x909 is in the Oualcomm HS-USB Diagnostics 9008 port. Completely brick. What we gonna do with it ? Where i may download unbrick files and will see unbrick method? Need just rowprogram0.xml, patch0.xml, 8064_msimage.mbn, MPRG8064.hex for OPPO find5 x909 strongly.
2) How i can place other (working) smartphone in Download mode? What i gonna press?
Sorry for my english, and thank you.

olezhek1975 said:
1) Can you give me some advices? Smartphone OPPO find 5 x909 is in the Oualcomm HS-USB Diagnostics 9008 port. Completely brick. What we gonna do with it ? Where i may download unbrick files and will see unbrick method? Need just rowprogram0.xml, patch0.xml, 8064_msimage.mbn, MPRG8064.hex for OPPO find5 x909 strongly.
2) How i can place other (working) smartphone in Download mode? What i gonna press?
Sorry for my english, and thank you.
Click to expand...
Click to collapse
I suggest you to ask addel in oppo forum, she can help you just pm her and tell your problem, because she has an app like odin in samsung to totally flash new rom inage from pc like odin did. But its not officially released by oppo and its hard to find, so i suggest you to contact her
Sent from my GT-I9205 using XDA Free mobile app

I can' get it to boot properly. Help me please!

A friend of mine gave me this phone after unexpected self shutdown. The phone was in a boot loop. At this point where I am right now I think I tried everything I can. I have read various guides and tutorials how to bring this phone back to life and nothing works for me. I suppose that there is some damage on mainboard but till I losse this phone I want to be sure. So the situation looks like this. Since the bootloader in locked and there is no working OS I am not able to unlock the bootloader. (If I am wrong here tell me please because I can't find a solution "how to unlock bootloader without having working OS"). The only metode to flash this phone in this state is to use QFIL. Flashing through fastboot fails everytime - booloader locked -> no *.img flashing. So I have 4 various versions of stock ROM for this phone and after flashing via QFIL the phone doesn't boot. It end with 3 possible ways. 1'st way - clasic bootloop. 2'nd way - frozen on loading screen. 3'rd way - black screen with blue LED, USB diagnostics state, 9006 port opened, no chance to flash because of closed QD port 9008. After this I have to erase every single one of the partitions made through flashing. Then I am able again to flash with QFIL.
I have no idea where is the problem here or what am I doing wrong. I tested the internal memory with a partitioning program in search of bad sectors -> 100% OK. Filled the whole memory with zero's and then formated it. It didn't help. Are every of my stock ROMs broken or is this phone realy damaged? Dear XDA community help me please! I have no clue what can I still try.

Tried ZUI QPST image or CM one?

ankurpandeyvns said:
Tried ZUI QPST image or CM one?
Click to expand...
Click to collapse
CM through QFIL already tried. Doesn't boot. I've got .zip ROM images but without TWRP no chance to use it. I have got also an image in .qsb file but no idea how to push it into the phone. Will it work through fastboot to put the file into the phone and than flash through diagnostic mode ?

kotex said:
CM through QFIL already tried. Doesn't boot. I've got .zip ROM images but without TWRP no chance to use it. I have got also an image in .qsb file but no idea how to push it into the phone. Will it work through fastboot to put the file into the phone and than flash through diagnostic mode ?
Click to expand...
Click to collapse
I just recommend you downloading this https://drive.google.com/open?id=0B7zm16vLHfdBVi1lWlMwelBBdXc . It's ZUI 2.0.49 for qfil, hope it works for you.

kotex said:
CM through QFIL already tried. Doesn't boot. I've got .zip ROM images but without TWRP no chance to use it. I have got also an image in .qsb file but no idea how to push it into the phone. Will it work through fastboot to put the file into the phone and than flash through diagnostic mode ?
Click to expand...
Click to collapse
Download the CM QFIL image from my video. It should work.

ankurpandeyvns said:
Download the CM QFIL image from my video. It should work.
Click to expand...
Click to collapse
Already tried your copy. To be honest tried it many times in every way I could. The phone is now sitting for over 3h frozen on loading screen. It is never going to boot or tell me that this is normal... Ereased the whole internal memory by delting every existing partition and then flashed it via QFIL. Also tried to format the whole memory in ext4. Same result. Like I said the phone is laying right now for over 3h on the same CYANOGEN screen with some graphical artifacts.
Borja Viera said:
I just recommend you downloading this https://drive.google.com/open?id=0B7zm16vLHfdBVi1lWlMwelBBdXc . It's ZUI 2.0.49 for qfil, hope it works for you.
Click to expand...
Click to collapse
OMG This room booted normaly. Thank you some much my friend! You made my day. It is a step forward. However all connections aren't working. I can't find "OEM unlocking" under Developer Options. I want to unlock the Bootloader as soon as possible so I will be able to put TWRP recovery and then flash it with any available CustomROM

kotex said:
Already tried your copy. To be honest tried it many times in every way I could. The phone is now sitting for over 3h frozen on loading screen. It is never going to boot or tell me that this is normal... Ereased the whole internal memory by delting every existing partition and then flashed it via QFIL. Also tried to format the whole memory in ext4. Same result. Like I said the phone is laying right now for over 3h on the same CYANOGEN screen with some graphical artifacts.
Click to expand...
Click to collapse
What's the result after flashing ZUI 2.5.330 image?

ankurpandeyvns said:
What's the result after flashing ZUI 2.5.330 image?
Click to expand...
Click to collapse
Many hours frozen on black screen with blue led. 9008 QD port blocked. 9006 USB Diagnostics port opened. No chance to flash until all partitions are erased and the port is reset. Otherwise I need to try getting to the 9008 port by puting the USB cable while holding the "Vol Up" button and then flash it agin with QFIL.

kotex said:
Many hours frozen on black screen with blue led. 9008 QD port blocked. 9006 USB Diagnostics port opened. No chance to flash until all partitions are erased and the port is reset. Otherwise I need to try getting to the 9008 port by puting the USB cable while holding the "Vol Up" button and then flash it agin with QFIL.
Click to expand...
Click to collapse
Got successful in flashing?

ankurpandeyvns said:
Got successful in flashing?
Click to expand...
Click to collapse
Yes
Right now thanks to Borja Viera I used the working OS to make a "sdfuse" folder on the internal memory, put the .qsb image file into the folder and flash the phone through diagnostic mode. I have got right now android 5.1.1 on it and it booted normaly However the connections still aren;t working. I managed to enable "OEM unlocking" then got to the fastboot mode with a bit of help from AIO tool (because turning the phone with pressed "Vol Up" and "Vol Down" buttons at the same time makes the menu but no "go to bootloader" shortcut over there). Unlocked the bootloader manualy with minimal ADB. Then I wasn't able to put TWRP as the recovery because of some weird error comming every time I tried the command. So I flashed the phone once again back to CM 12.1 soft only to get other "the better one - with many options" bootloader. Tried flashig TWRP once again and voila! TWRP working!! Bootloader unlocked! In a while I will be downloading some CustomROM and turn this phone back to life... I hope so
[UPDATE]
Tried 5 different ROMs:
Two Cyanogen:
1'st - black screen blue led usb diagnostics state with port 9006 opened
2'nd - frozen on loading screen
Three CustomROMs:
1'st Official Lineage
2'nd Unofficial Lineage
3'rd AICP-12.1
All three are not booting. Phone resets itself on loading screen -> boot loop. Do you have any sugestion right now? In TWRP everything wiped and ROM installed on clean phone. Gapps installed too from Open Gapps website. Eveything done right with the instructions.
Is this phone really damaged?

kotex said:
Yes
Right now thanks to Borja Viera I used the working OS to make a "sdfuse" folder on the internal memory, put the .qsb image file into the folder and flash the phone through diagnostic mode. I have got right now android 5.1.1 on it and it booted normaly However the connections still aren;t working. I managed to enable "OEM unlocking" then got to the fastboot mode with a bit of help from AIO tool (because turning the phone with pressed "Vol Up" and "Vol Down" buttons at the same time makes the menu but no "go to bootloader" shortcut over there). Unlocked the bootloader manualy with minimal ADB. Then I wasn't able to put TWRP as the recovery because of some weird error comming every time I tried the command. So I flashed the phone once again back to CM 12.1 soft only to get other "the better one - with many options" bootloader. Tried flashig TWRP once again and voila! TWRP working!! Bootloader unlocked! In a while I will be downloading some CustomROM and turn this phone back to life... I hope so
[UPDATE]
Tried 5 different ROMs:
Two Cyanogen:
1'st - black screen blue led usb diagnostics state with port 9006 opened
2'nd - frozen on loading screen
Three CustomROMs:
1'st Official Lineage
2'nd Unofficial Lineage
3'rd AICP-12.1
All three are not booting. Phone resets itself on loading screen -> boot loop. Do you have any sugestion right now? In TWRP everything wiped and ROM installed on clean phone. Gapps installed too from Open Gapps website. Eveything done right with the instructions.
Is this phone really damaged?
Click to expand...
Click to collapse
If you're still in warranty, the best bet will be to get it replaced. Because it seems like a serious issue in the hardware.

kotex said:
Yes
Right now thanks to Borja Viera I used the working OS to make a "sdfuse" folder on the internal memory, put the .qsb image file into the folder and flash the phone through diagnostic mode. I have got right now android 5.1.1 on it and it booted normaly However the connections still aren;t working. I managed to enable "OEM unlocking" then got to the fastboot mode with a bit of help from AIO tool (because turning the phone with pressed "Vol Up" and "Vol Down" buttons at the same time makes the menu but no "go to bootloader" shortcut over there). Unlocked the bootloader manualy with minimal ADB. Then I wasn't able to put TWRP as the recovery because of some weird error comming every time I tried the command. So I flashed the phone once again back to CM 12.1 soft only to get other "the better one - with many options" bootloader. Tried flashig TWRP once again and voila! TWRP working!! Bootloader unlocked! In a while I will be downloading some CustomROM and turn this phone back to life... I hope so
[UPDATE]
Tried 5 different ROMs:
Two Cyanogen:
1'st - black screen blue led usb diagnostics state with port 9006 opened
2'nd - frozen on loading screen
Three CustomROMs:
1'st Official Lineage
2'nd Unofficial Lineage
3'rd AICP-12.1
All three are not booting. Phone resets itself on loading screen -> boot loop. Do you have any sugestion right now? In TWRP everything wiped and ROM installed on clean phone. Gapps installed too from Open Gapps website. Eveything done right with the instructions.
Is this phone really damaged?
Click to expand...
Click to collapse
Do you have any telegram account, we could make things faster if we communicate that way.

ankurpandeyvns said:
If you're still in warranty, the best bet will be to get it replaced. Because it seems like a serious issue in the hardware.
Click to expand...
Click to collapse
Asked my firend about it. The phone is like 1 month old. He was making some pictures and the phone suddenly died and got to boot loop. He bought it new on ebay. Shipped from China. He already made some research about the warranty before he gave it to me. He made some calls and emails to customer service here in Germany and they told him that he has to send the phone back to China. No warranty in Germany. It is not worth to send it back to China because of duty tax on the way to China. They send him this phone on some special shipping method to avoid this taxes and stay with profitable shipping price. But if you need to send it back they won;t help you at all. And the dispatch price is a no-go.
Since I have decent experience with electronics and flashing various smartphones he gave it to me with a though that I will be able to bring it back to life.
I already said when I started this topic that I suppose that this phone has some damage on the mainboard because of the weird behaviour. I just want to be sure about that and try everything I can before I tell him that he wasted his money by buying this phone.
I want to thank you for your support! If you have some ideas what could I still try I will gladly listen.

kotex said:
Asked my firend about it. The phone is like 1 month old. He was making some pictures and the phone suddenly died and got to boot loop. He bought it new on ebay. Shipped from China. He already made some research about the warranty before he gave it to me. He made some calls and emails to customer service here in Germany and they told him that he has to send the phone back to China. No warranty in Germany. It is not worth to send it back to China because of duty tax on the way to China. They send him this phone on some special shipping method to avoid this taxes and stay with profitable shipping price. But if you need to send it back they won;t help you at all. And the dispatch price is a no-go.
Since I have decent experience with electronics and flashing various smartphones he gave it to me with a though that I will be able to bring it back to life.
I already said when I started this topic that I suppose that this phone has some damage on the mainboard because of the weird behaviour. I just want to be sure about that and try everything I can before I tell him that he wasted his money by buying this phone.
I want to thank you for your support! If you have some ideas what could I still try I will gladly listen.
Click to expand...
Click to collapse
If you have telegram, drop a message @ankurpandeyvns

Lenovo k6 Power Hard Bricked.

No Fastboot, No Recovery, No Download Mode, just a black screen. All Partitions of Phone got deleted. Pc is only detecting it as "Qualcomm HS-Usb Diagnostic 900E(Com10)" but unable to flash stock firmware. Getting the following error in Qfil.
...
"Download Fail:Switch To EDL FailFailed to Switch to Emergency Download mode".
Phone is also heating up as it have no OS installed.

I also faced this same problem in the past but i was able to recover my phone. Right now i don't remember how i did it but give me some time to think about it. I am sure someone else will help you just don't give up!!
Go to this link and try to follow their tutorial. It might help you.
https://firmwarefile.com/lenovo-vibe-k6-power-k33a42

ImSSin said:
I also faced this same problem in the past but i was able to recover my phone. Right now i don't remember how i did it but give me some time to think about it. I am sure someone else will help you just don't give up!!
Go to this link and try to follow their tutorial. It might help you.
https://firmwarefile.com/lenovo-vibe-k6-power-k33a42
Click to expand...
Click to collapse
Thank You ?
I am also trying my best to recover the phone and i will write here so that anyone who is facing this issue can recover his/her Phone.

No Solution found for this.
...
You have to send your Lenovo K6 Power to Lenovo Service Centre and get your Motherboard replaced.
If your phone is in guarantee then you will get free replacement no matter if your phone is rooted but please don't tell about root to them otherwise they will charge money for your small mistake.

what happened?

Do a new install

faizynadim said:
No Fastboot, No Recovery, No Download Mode, just a black screen. All Partitions of Phone got deleted. Pc is only detecting it as "Qualcomm HS-Usb Diagnostic 900E(Com10)" but unable to flash stock firmware. Getting the following error in Qfil.
...
"Download Fail:Switch To EDL FailFailed to Switch to Emergency Download mode".
Phone is also heating up as it have no OS installed.
Click to expand...
Click to collapse
Boss it seems that you have hard bricked your phone so it means it's first boot has been corrupted there is no chance as first boot is mandatory to flash any file, there are some tools like octopus, or Medusa box, they can repair your boot then the phone can be used its just an outside chance 5o get it in workable condition look for some person or Repairing person have this boot repairing gadget,
If this fails too or you have messed up very badly then, last option is mother board replacement, there is no software option to repair by yourself

Help please..!!!!
:crying:
Even I face the same problem...
How do I go to download mode..???
It's stuck at Lenovo screen .... It just turn off on low battery and reboots on long press of power button.. Is it compulsory to have 80% of charge to get into download mode..???

i did the same. it switches on with lenovo logo , shows the os logo animation and its stuck there. when i tried connecting it to phone it showing unspecified device.
i could get into a fastboot mode . but nothing ahead to that. please find me a solution

Help me same issue
faizynadim said:
No Fastboot, No Recovery, No Download Mode, just a black screen. All Partitions of Phone got deleted. Pc is only detecting it as "Qualcomm HS-Usb Diagnostic 900E(Com10)" but unable to flash stock firmware. Getting the following error in Qfil.
...
"Download Fail:Switch To EDL FailFailed to Switch to Emergency Download mode".
Phone is also heating up as it have no OS installed.
Click to expand...
Click to collapse
Did you find any solution for this, present i'm facing same issue, please tell me if you have any solution for this...

Bricked A2017G

Hey Folks, i just bricked My Axon 7 some Days ago. It started randomly a reboot which i can't abort anymore. Everytime the Device get's a Charge does it start again. I can't enter TWRP or Fastboot (Reboots after a few Seconds). Same for the Flash Mode. It is now completely discharged and i don't know how to recover it. Any Ideas?
Think i can't fix this, but asking here don't hurts... :angel:

4th grade unbrick guide here in the Forums. That helped me after i cannot access any Mode. No Flash Mode, No EDL, No USB, No Qualcomm Loader. Axon 7 too.
https://forum.xda-developers.com/axon-7/how-to/a2017-4th-category-brick-repair-manual-t3585898

HighSierra1014 said:
4th grade unbrick guide here in the Forums. That helped me after i cannot access any Mode. No Flash Mode, No EDL, No USB, No Qualcomm Loader. Axon 7 too.
https://forum.xda-developers.com/axon-7/how-to/a2017-4th-category-brick-repair-manual-t3585898
Click to expand...
Click to collapse
Lol. I made a guide based on that one but updated, called DFU unbrick, because everybody had to read my comments there anyways to be able to do it. Not sure why everyone still uses the old one ?
@Miustone: If you want, you can try an EDL cable first. A lot of people say that they could get out of DFU that way. (assuming that you can get into EDL/DFU that is). Google my guide, it's called "DFU unbrick", if the EDL cable doesn't work

Thanks Guys! I will take a look on the DFU unbrick and the EDL Cable. At least a blink of Hope for this great Device... Still good as new, would be sad to use it just as a golden Sculpture lol

Miustone said:
Hey Folks, i just bricked My Axon 7 some Days ago. It started randomly a reboot which i can't abort anymore. Everytime the Device get's a Charge does it start again. I can't enter TWRP or Fastboot (Reboots after a few Seconds). Same for the Flash Mode. It is now completely discharged and i don't know how to recover it. Any Ideas?
Think i can't fix this, but asking here don't hurts... :angel:
Click to expand...
Click to collapse
Hey, sorry for asking but how did you brick it? I am thinking about installing a custom ROM, rooting etc and I would just like to know if it was something in specific so I can stay away from it. Cheers.

Any help with fully bricked device

Hello!
THink I have bricked my phone, but just checking before I go through what I suppose is a long process with oneplus.
Looking for any help. I had a working device - unlocked bootloader and installed TWRP and magisk using MauronofrioTool. ok - however, I found out I couldn't use a fingerprint security option on that would have been anoying. So... Long story short. I used MauronofrioTool to relock bootloader. Oops - so that didn't work. THen found out I couldn't do anything except stare at g.co/ADH message on my screen. Couldn
't get to fastboot or TWP. ANyway, so I managed to up and down volume and enter into TWRP. Was still connecting to the tool, so I downloaded factory Zips and tried to install via tool after unlocking - Seemed to be working ... but it stopped mid way through a process and hasbn't come back! NOthing at all. I wonder if I could have triggered an OEM thing? ANyway - literally nothing no buttons work no screen action. I see a QUSB_BULK_CID:etc number when connecting the phone, but that is it. No fast boot or any other actions available.
PLease, pretty devastating, Anyone know if I can do anything?

I'm no pro but I use this tool which helped me:

henk-jan said:
I'm no pro but I use this tool which helped me:
Click to expand...
Click to collapse
Thank you. I feel I am little past this stage now though.. Also trying the brick reprieve software . Just can't get my computer to recognise the phone now. No ability to get to emergency download path - think it is my crappy cihinese pc (old Huawei tablet basically) or Windows via apple that have me stranded.
**********SOLVED
THe crappy Chinese language Windows tablet worked as the unbrick OP said WIndows would. Must be a kink in the Windows via Mac that could get me into the situation, but not out.
Very relieved... Even though I still am not 100% sure what I actually ended up clicking to get it to register and connect with the unblock tool (which of course was in Chinese) hahaha.
Cheers
CHeers though

Glad you got it sorted out! Cheers

Need Help, please
Just received my OnePlus 8 pro, decided to Root and unlock the bootloader---this went fine.
I then went and upgraded to Android 11 DP3.
I'm now only able to get into Fastboot. at points it will try to boot but only get to the logo screen and then goes black.
When the phone boots up, it goes to Qualcomm CrashDump Mode.
I've been attempting to solve this for half the day with no luck. I've tried Msmtool, but it doesn't recognize the device, even after loading drivers again.
Is there a way to load a ROM from fastboot mode?
Hoping someone can assist, this is super frustrating and I would appreciate any help, please.
Rick

rickhurl said:
Just received my OnePlus 8 pro, decided to Root and unlock the bootloader---this went fine.
I then went and upgraded to Android 11 DP3.
I'm now only able to get into Fastboot. at points it will try to boot but only get to the logo screen and then goes black.
When the phone boots up, it goes to Qualcomm CrashDump Mode.
I've been attempting to solve this for half the day with no luck. I've tried Msmtool, but it doesn't recognize the device, even after loading drivers again.
Is there a way to load a ROM from fastboot mode?
Hoping someone can assist, this is super frustrating and I would appreciate any help, please.
Rick
Click to expand...
Click to collapse
https://forum.xda-developers.com/oneplus-8-pro/how-to/rom-stock-fastboot-roms-oneplus-8-pro-t4083997

cultofluna said:
https://forum.xda-developers.com/oneplus-8-pro/how-to/rom-stock-fastboot-roms-oneplus-8-pro-t4083997
Click to expand...
Click to collapse
Thanks so much. I ended up getting Msmtool to work. Although my device wasn't on (black screen) and it didn't fully show up in the tool, I decided to start the process anyway and it began to load.
I've been on here for over 10 yeas (XDA) I've just lost my account info and made a new one.
Thanks for taking the time to respond. Much appreciated.