I can't figure this phone out with regard to charging.
1) Won't charge via computer USB (I've heard the reasoning for this - still seems stupid)
2) Charging w/ 1amp 5V wall charger - phone screen is non responsive to touch, but phone charges (unplugging it unfreezes the screen)
3) 1amp accessory USB charger, won't charge the phone at all.
Are the charging limitations software or hardware based. I can't come to terms with the fact that this phone can't at least charge by USB. It doesn't need to be lightening fast, but it should at least charge.
Is there anything that can be done?
are u using OEM charger and USB cable ?
charging by USB
My phone charges with just the USB cord and a PC, It is a bit slow to charge that way, but it charges. Are you sure you are using a powered USB port?
it will charge via USB, you just need to install the motorola drivers. it needs more current than the original USB standards allowed for. USB can provide that current now, but you need the drivers.
Not OEM
None of the above are OEM chargers and the cables are no OEM either (Wouldn't think the cable has anything to do with it).
Since i am out and about a bit, i have to have a portable battery powered backup charger, i also carry a wall/car charger that is capable of doing both at the same time.
cable has nothing to do with it. The power requirements are strict for this phone, and it's all down to the proper way to charge the battery.
I know for a fact that the generic energizer car charger i picked up with interchangeable ends for different USB types works perfectly for this phone. It might be worth it to just jump on ebay and grab another OEM battery instead of trying to run around with chargers.
have you measured the output of those 1a chargers? i have an adapter from china that says 1a but only puts out 0.3a and doesnt charge my atrix either.
I am still using the chargers I had from my blackberry 8900. The bb wall charger works great. The car charger (att) with the flip cover over a usb makes my phone hot as hell but it still charges.
Think i've also found that, once you have the motorola drivers installed on your computer, disabling the data connection to the phone (as in selecting "None" for the USB connection option in the notification pane after you connect the phone) seems to allow the phone to charge a fair bit faster over USB. Kinda makes sense too when you're thinking about it... since it wouldn't be constantly accessing the phone as a storage device.
Yes some wall chargers dont work i.e. the two I had from my Nexus One, BB chargers seem to work well as I believe they needed more juice to charge in the first place, for the usb cable, the best solution to try is getting the updated usb drivers as mentioned.
Got an old iPhone usb charger with a generic usb lead which charges the phone fine but when it hits 100% the alert to say it is fully charged never happens yet if I then change to the official samsung usb lead after 5 or so minutes the phone then vibrates and says it is now fully charged.
Not so much an issue as the phone charges fine just wondering if anyone else has seen this
The good news is with this 'feature' the phone doesn't wake me up when it's finished charging!
I've seen problems like this when using other generic usb chargers on other phones. I believe the wattage provided for charging can vary, which can cause issues.
I used Samsung's data cable connected to an HTC charger and the phone launched the MTP screen and tried to connect to my power outlet via USB. I haven't had a Samsung phone in years but from this I'm guessing that they're pretty sensitive when it comes to cables and chargers. I ordered OEM cables and chargers just to be safe.
When i charge my phone from a wall charger it charges perfectly all the way up to 100%. However if i charge it using my pc from its usb port using a usb cable it usually charges upto only 14% and then gets stuck at it, charging is also very slow compared to charging with the wall charger and i do also sometimes get random reboots when charging it with my pc using usb. So how do i fix this issue as i do not currently own a wall charger of my own and have to borrow it from my cousin
Problem solved
so i figured out what the problem was and now it's charging all the way upto a 100%.
instead of plugging the usb cable using a usb extension or on my casing's USB port i plugged it directly into the USB 2.0 port at the back of my mother board and it started charging normally again . no random reboots etc. So please close the thread
Last night I was charging my S4 in my car adapter, but noticed the cattery was still going down. I went home and plugged it into my AC (wall charger) and went to bed. The next morning the S4 was dead and couldn't charge. The only solution was to plug it in my computer and went an hour for it to get some charge back.
I have a root i337m running rootbox 4.1, and I went into TWRP to wiped the phone and installed the ROM again - no luck.
Is this a battery issue, a software issue or a whole device issue? Thanks.
freddywhite said:
Last night I was charging my S4 in my car adapter, but noticed the cattery was still going down. I went home and plugged it into my PC and went to bed. The next morning the S4 was dead and couldn't charge. The only solution was to plug it in my computer and went an hour for it to get some charge back.
I have a root i337m running rootbox 4.1, and I went into TWRP to wiped the phone and installed the ROM again - no luck.
Is this a battery issue, a software issue or a whole device issue? Thanks.
Click to expand...
Click to collapse
I don't think its a rom issue. I tried charging via USB as well and had phone charging a few hours and it ate crap. So I only charge via AC outlet only. USB charges but at a very slow pace.
Reinaldo33897 said:
I don't think its a rom issue. I tried charging via USB as well and had phone charging a few hours and it ate crap. So I only charge via AC outlet only. USB charges but at a very slow pace.
Click to expand...
Click to collapse
I made an error in the OP - I meant to say I left it to charge on the wall and I got nothing.
Right now, the charge light doesn't even come on if I plug it with AC.
freddywhite said:
I made an error in the OP - I meant to say I left it to charge on the wall and I got nothing.
Right now, the charge light doesn't even come on if I plug it with AC.
Click to expand...
Click to collapse
Maybe see the results by changing the charger you're using?
r8revealed said:
Maybe see the results by changing the charger you're using?
Click to expand...
Click to collapse
I've tried 3-4 different chargers and cables, same issue. Charges slowly through PC,doesn't charge at all with AC. Did a factory reset after reverting to stock FW, no luck.
freddywhite said:
I've tried 3-4 different chargers and cables, same issue. Charges slowly through PC,doesn't charge at all with AC. Did a factory reset after reverting to stock FW, no luck.
Click to expand...
Click to collapse
I doubt it's a ROM issue, but there's no harm in reverting back to stock to see the results (assuming you've backed it up). If it all fails, i think you should unroot and send it to Samsung for the warranty. Software problems are somewhat easier to fix here than hardware, so it may be the best option to let Samsung handle it.
I had similar problems with my Note 2 before and now with my S4. What I found was, sometimes the usb cable wasn't tightly plugged into the wall charger. Once I've made sure of this, I've been able to charge (AC) every time.
I found this article that indicates that the S4 is looking for special sauce on the D+D- pins.
http://www.anandtech.com/show/6914/samsung-galaxy-s-4-review/2
Obviously the Galaxy S 4 will charge with any USB charger, but the charge time will simply be longer. Samsung uses a voltage divider and signals the presence of their own charger by sending 1.2-1.3 V across the D+ / D- pins, this is similar to what Apple does with 2.0 or 2.8 V across the pins for various USB chargers they've shipped over the years. This signaling is essentially Samsung's proprietary tablet charging signaling which they've employed on the Galaxy Note 2 and now SGS4, in fact the two use the same exact charger, so it's worth tossing out your old ones and getting the appropriate one to take advantage of the faster charging.
However I do not believe this to be 100% true. I think not all chargers will work..
I took a charger that is very vanilla (Wall charger but the D+D- pins are NC) and it works with the S3 and NEXUS7 but does not work with the S4.
This charger uses a stock USB cable so I took a wall charger that had gone bad but had a dedicated cable and hacked off the end and wired up my own cable...
That works! So it appears that the S4 will only charge properly with certain chargers that do something to the D+D- pins (either shorting them with a resistor like the article indicates
I then took a look at the cable I used to replace. It is a Motorola cable and it has the ID pin pulled high built into the cable... So I suspect that is required for the phone to work... But to fast charge it will need the special sauce indicated above!
Had the same issue and found the solutions which worked for me. Go into the developer mode and deactivate the usb debug mode.
Had the exact same issue. I took a soldering iron to my charging port on my phone. Problem solved. The ID pin had a bad joint.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app
I have a strange issue, my s4 is detected by pc, charges normally with usb ( wall or pc charge ) my battery is full but when I take the cable from microUSB port and s4 should work with the battery, turns off and consumes no battery, it's like refusing to use the battery and that it is full! battery checked on a sph l 720
I've tried installing other roms with safestrap but I still have the same problem, refuses to consume battery and while the battery is at 100% ,my s4 shows 0% if I disconnect the usb cable... game over. However, I can be on the safestrap menu for hours only with the battery, no problem, is a problem of rom I think but did not know how to fix it .. : (
I'm having the same issue as the original poster. The USB port is good, charges fine when connected to PC (although much slower because of different mVS). Have tried amidst everything and nothing fixes it. I've turned debugging mode off and back on, restore to backup, complete wipe and reinstall of 2 ROMs with and without apps, fix permissions, different kernels, different USB cables... The adaptor is in good condition. But when plugged in while on my phone doesn't recognize that's it's connected. Previously out would give a false charging reading. If off sometimes I got the grey bar battery but note is just vibrating every few seconds. Idk what to do...
crazy_dr0id said:
I'm having the same issue as the original poster. The USB port is good, charges fine when connected to PC (although much slower because of different mVS). Have tried amidst everything and nothing fixes it. I've turned debugging mode off and back on, restore to backup, complete wipe and reinstall of 2 ROMs with and without apps, fix permissions, different kernels, different USB cables... The adaptor is in good condition. But when plugged in while on my phone doesn't recognize that's it's connected. Previously out would give a false charging reading. If off sometimes I got the grey bar battery but note is just vibrating every few seconds. Idk what to do...
Click to expand...
Click to collapse
I'd guess it's the charger. Get a new one
Sent from my Nexus 5 using XDA Free mobile app
I had the same problem. S4 will recognize charger as USB charger, not AC. solution was to clean usb port connector, was some cloth covering wires. then restarted and worked ok
I am having trouble charging the phone the same way. I have reset the phone 3 times and still can't get a charge.
So its been a while since my s4 i9500 wall charger's cable been cut. Although the phone does get charged up. It isnt charging up quickly as it used to before the wire was cut. Sometimes the phone doesnt even charge even thought the battery icon shows that it is charging.
Now, I have been thinking of replacing the charger. But do i have to buy the charger or should i just replace the cables? I have a lot of micro usb cables . Can i use them with the adapter to charge up my phone?
You can use quite literally any micro-usb 2.0 cable and any usb charger to charge it; however, to achieve the maxium charging speed (1900mah) you will need a high quality shielded micro-usb cable (like the stock Samsung cable) and a 2A (or higher) usb charger (like the stock Samsung charger or an iPad charger).