HI there,
DOes anyone have a solution for us stuck on MK2?
I have the following problems:
I bought this i337 second hand, and it came with UCUAMK2 firmware.
I rooted it with SAFEROOT (saferoot.zip). That worked fine.
But I cant install LOKI, to get the ClockWorkMod, so I can't install Custom ROMs.
Because when I type in the commands in Android Terminal, to flash loki's CWM recovery, it says :
[+] loki_flash v1.1
[-] Loki aboot version does not match device.
SO i figure, I have to revert back to MDB or MDL firmware.
BUT when I open ODIN, and try to flash the official firmware:
1. I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5
it FAILS in ODIN, so I (try) to flash this:
2.I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5
but that FAILS also!!!!!!!
SO should I install SAFESTRAP?
Some ppl complain, that screws things up, and end up in bootloop, and can't remove this SAFESTRAP...so i dunno if
i should install it.
Does flashing via/using ODIN FAIL==> because my bootloader is LOCKED?
Can you tell me how to Unlock my bootloader????
I need to go back to MDB or MDL, because otherwise I can't unlock the carrier restriction, since I'm on Vodafone,
and not on AT&T!
Plus, I was always installing custom Roms on my S2, S3, and all my other android devices since 2009....sorry to see
that the S4 is
such a headache....
Can you help me out please, seeing how good aof a DEV you are....?
Please and thank you
djmisi
You SOL buddy. Sell the phone and get something else. You will never be able to downgrade
MOTO X SLAPPED
djmisi99 said:
HI there,
DOes anyone have a solution for us stuck on MK2?
I have the following problems:
I bought this i337 second hand, and it came with UCUAMK2 firmware.
I rooted it with SAFEROOT (saferoot.zip). That worked fine.
But I cant install LOKI, to get the ClockWorkMod, so I can't install Custom ROMs.
Because when I type in the commands in Android Terminal, to flash loki's CWM recovery, it says :
[+] loki_flash v1.1
[-] Loki aboot version does not match device.
SO i figure, I have to revert back to MDB or MDL firmware.
BUT when I open ODIN, and try to flash the official firmware:
1. I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5
it FAILS in ODIN, so I (try) to flash this:
2.I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5
but that FAILS also!!!!!!!
SO should I install SAFESTRAP?
Some ppl complain, that screws things up, and end up in bootloop, and can't remove this SAFESTRAP...so i dunno if
i should install it.
Does flashing via/using ODIN FAIL==> because my bootloader is LOCKED?
Can you tell me how to Unlock my bootloader????
I need to go back to MDB or MDL, because otherwise I can't unlock the carrier restriction, since I'm on Vodafone,
and not on AT&T!
Plus, I was always installing custom Roms on my S2, S3, and all my other android devices since 2009....sorry to see
that the S4 is
such a headache....
Can you help me out please, seeing how good aof a DEV you are....?
Please and thank you
djmisi
Click to expand...
Click to collapse
You will need to use safestrap.
Loki does not work with MK2 because they patched it in the MK2 update.
At this point in time the bootloader cannot be unlocked.
el o el
The s4 is nothing like previous samsung devices...at least on att, the bootloader is locked, safestrap is your only option.
Also keep in mind, att stated about a year ago they will no longer be supporting phones with unlocked bootloaders...so the problem you are experiencing now can be expected on every new att branded phone
Sent from my SAMSUNG-SGH-I337 using Tapatalk
djmisi99 said:
HI there,
DOes anyone have a solution for us stuck on MK2?
I have the following problems:
I bought this i337 second hand, and it came with UCUAMK2 firmware.
I rooted it with SAFEROOT (saferoot.zip). That worked fine.
But I cant install LOKI, to get the ClockWorkMod, so I can't install Custom ROMs.
Because when I type in the commands in Android Terminal, to flash loki's CWM recovery, it says :
[+] loki_flash v1.1
[-] Loki aboot version does not match device.
SO i figure, I have to revert back to MDB or MDL firmware.
BUT when I open ODIN, and try to flash the official firmware:
1. I337UCUAMDB_I337ATTAMDB_I337UCUAMDB_HOME.tar.md5
it FAILS in ODIN, so I (try) to flash this:
2.I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5
but that FAILS also!!!!!!!
SO should I install SAFESTRAP?
Some ppl complain, that screws things up, and end up in bootloop, and can't remove this SAFESTRAP...so i dunno if
i should install it.
Does flashing via/using ODIN FAIL==> because my bootloader is LOCKED?
Can you tell me how to Unlock my bootloader????
I need to go back to MDB or MDL, because otherwise I can't unlock the carrier restriction, since I'm on Vodafone,
and not on AT&T!
Plus, I was always installing custom Roms on my S2, S3, and all my other android devices since 2009....sorry to see
that the S4 is
such a headache....
Can you help me out please, seeing how good aof a DEV you are....?
Please and thank you
djmisi
Click to expand...
Click to collapse
There is NO WAY back from mk2. You can flash custom roms ONLY with Safestrap. No CWM no TWRP. Read this guide, it has everything you need to know for the S4. There is nearly 30 custom roms tested & affirmed working. Good luck & happy reading.
http://forum.xda-developers.com/showthread.php?t=2616221
SGS4 AT&T i337 on Stock MK2...jeboo kernel/recovery needed to install SHOstock v3.0 ?
I am very familiar with custom roms and your kernels, from always using them on my SGS2 i777 (AT&T), but i just bought an SGS4 i337 AT&T, on MK2 baseband, and everybody suggested I should install the SHOstock v3.0 for the i337 (http://forum.xda-developers.com/show....php?t=2305752).
Problem is, I am sooooo confused now, because there is jeboo kernels: (Jeboo_Kernel_i337_v3_0a-i.zip, Jeboo_Kernel_i337_v3_0a.zip, Jeboo_Kernel_i337_v3_0.zip, Jeboo_Kernel_i337_v2_2.zip)
...than there's your RECOVERY: Jeboo_Recovery_v2_1.zip
so Im very confused now how I should go about installing our most awesome DEV shoman94's SHOstock v3.0) ROM...==> THAT I DUNNO WHAT SHOULD I DO ANYMORE.....
1. Because, on the thread there (http://forum.xda-developers.com/show....php?t=2305752), in POST#1 it says , in the Instructions, that :We must be running a custom recovery using Jeboo's Recovery from Post#4 which is your Jeboo_Recovery_v2_1.zip
2. But how should I run the Jeboo_Recovery_v2_1.zip RECOVERY, if Im on SafeStrap 3.71 (which is a recovery also)???
3. If i flash Jeboo_Recovery_v2_1.zip, wont that brick (or softbrick) the S4?
4. Or if I flash Jeboo_Recovery_v2_1.zip, will I end up having 2 recoveries? Or will I only end up with having only the Jeboo_Recovery_v2_1 ???
5. In POST#3, it says that:
IF YOUR PHONE HAS MF3/MK2 BOOTLOADERS, YOU MUST RUN THE MF3/MK2 STOCK KERNEL. DO NOT TRY INSTALLING ANYTHING BELOW UNLESS YOU HAVE MDB/MDL BOOTLOADERS THAT SUPPORT LOKI!!
So, should I NOT flash your Jeboo_Kernel_i337_v2_2.zip , since I am on MK2 stock kernel/baseband/bootloader....?
Check it out: http://i.imgur.com/cNWijKF.png
7. I mean, what is BELOW MF3/MK2 and ABOVE MDB/MDL? Because it also says, that: All binaries posted here will be loki'd (as signified by the .lok extension).
SO, keeping in mind that Im on Stock MK2 , but also Im ROOTED via SAFEROOT.zip (as you can see in the pic above: (http://i.imgur.com/cNWijKF.png) , can someone please tell me if I should flash this SHOstock v3.0, and more speciafically, WHICH, IF ANY of you jeboo kernels and Jeboo Recovery should I use?
Can I bug any of you to tell me the exact steps on how to get this SHOstock 3.0 on my i337, if I'm on MK2, rooted, and safestrap-ed?
ANy help would be much appreciated
djmisi99 said:
I am very familiar with custom roms and your kernels, from always using them on my SGS2 i777 (AT&T), but i just bought an SGS4 i337 AT&T, on MK2 baseband, and everybody suggested I should install the SHOstock v3.0 for the i337 (http://forum.xda-developers.com/show....php?t=2305752).
Problem is, I am sooooo confused now, because there is jeboo kernels: (Jeboo_Kernel_i337_v3_0a-i.zip, Jeboo_Kernel_i337_v3_0a.zip, Jeboo_Kernel_i337_v3_0.zip, Jeboo_Kernel_i337_v2_2.zip)
...than there's your RECOVERY: Jeboo_Recovery_v2_1.zip
so Im very confused now how I should go about installing our most awesome DEV shoman94's SHOstock v3.0) ROM...==> THAT I DUNNO WHAT SHOULD I DO ANYMORE.....
1. Because, on the thread there (http://forum.xda-developers.com/show....php?t=2305752), in POST#1 it says , in the Instructions, that :We must be running a custom recovery using Jeboo's Recovery from Post#4 which is your Jeboo_Recovery_v2_1.zip
2. But how should I run the Jeboo_Recovery_v2_1.zip RECOVERY, if Im on SafeStrap 3.71 (which is a recovery also)???
3. If i flash Jeboo_Recovery_v2_1.zip, wont that brick (or softbrick) the S4?
4. Or if I flash Jeboo_Recovery_v2_1.zip, will I end up having 2 recoveries? Or will I only end up with having only the Jeboo_Recovery_v2_1 ???
5. In POST#3, it says that:
IF YOUR PHONE HAS MF3/MK2 BOOTLOADERS, YOU MUST RUN THE MF3/MK2 STOCK KERNEL. DO NOT TRY INSTALLING ANYTHING BELOW UNLESS YOU HAVE MDB/MDL BOOTLOADERS THAT SUPPORT LOKI!!
So, should I NOT flash your Jeboo_Kernel_i337_v2_2.zip , since I am on MK2 stock kernel/baseband/bootloader....?
Check it out: http://i.imgur.com/cNWijKF.png
7. I mean, what is BELOW MF3/MK2 and ABOVE MDB/MDL? Because it also says, that: All binaries posted here will be loki'd (as signified by the .lok extension).
SO, keeping in mind that Im on Stock MK2 , but also Im ROOTED via SAFEROOT.zip (as you can see in the pic above: (http://i.imgur.com/cNWijKF.png) , can someone please tell me if I should flash this SHOstock v3.0, and more speciafically, WHICH, IF ANY of you jeboo kernels and Jeboo Recovery should I use?
Can I bug any of you to tell me the exact steps on how to get this SHOstock 3.0 on my i337, if I'm on MK2, rooted, and safestrap-ed?
ANy help would be much appreciated
Click to expand...
Click to collapse
You are making it too hard. You need to be on 3.71 Safestrap to flash Sho's 3.0. You must use default (stock) kernel. You can not flash any other kernels period. And no other recoveries. And no 4.4 or aosp roms. I am not on SafeStrap as I have a MDL phone. So, you need to go the SafeStrap thread and read up on flashing a rom on SafeStrap. There are a couple threads on the subject. Read all you can first and make any backup your phone/recovery allows before flashing. Also, do a clean wipe before installing rom. That may be different then a clean wipe on MDL/Custom Recovery, not sure--:good:
[email protected] said:
You SOL buddy. Sell the phone and get something else. You will never be able to downgrade
MOTO X SLAPPED
Click to expand...
Click to collapse
Problem is it came from AT&T Store with MDL ...but the MK2 update came through OTA...and that must of lock the bootloader....dayummmmmmm...
AM I right?
Yes
Maribou said:
You will need to use safestrap.
Loki does not work with MK2 because they patched it in the MK2 update.
At this point in time the bootloader cannot be unlocked.
Click to expand...
Click to collapse
Phone came from the Store with MDL, ( I see it on the Original box: SoftWare Ver: UCUAMDL....
The guy I bought it from rooted it, and loki-ed it... how did that OTA come through, I wonder? Once rooted and LOKI-ed...the OTAs shouldn't come through, right?
Sounds like the seller messed up and flashed back to stock. He was probably selling it to cut his losses.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app
Maribou said:
You will need to use safestrap.
Loki does not work with MK2 because they patched it in the MK2 update.
At this point in time the bootloader cannot be unlocked.
Click to expand...
Click to collapse
*************************************************************************
THX,
I just saw that the phone originally came with MDL baseband, its on the Original Box...
I wonder, was it with an unlocked bootloader at THAT time?
ANd the MK2 OTA update locked it?
djmisi99 said:
*************************************************************************
THX,
I just saw that the phone originally came with MDL baseband, its on the Original Box...
I wonder, was it with an unlocked bootloader at THAT time?
ANd the MK2 OTA update locked it?
Click to expand...
Click to collapse
Answer, yes & yes. There is plenty of custom roms for mk2 in the All things mk2 guide. You can also upgrade to 4.4.2 Kit Kat now as well. Forget about MDL cause there's no way to go back to it.
Maribou said:
You will need to use safestrap.
Loki does not work with MK2 because they patched it in the MK2 update.
At this point in time the bootloader cannot be unlocked.
Click to expand...
Click to collapse
Red_81 said:
Sounds like the seller messed up and flashed back to stock. He was probably selling it to cut his losses.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
******************************************
But if he had it LOKI-ed, that means he was just fine on MDL, no need for SafeSTrap, unlocked BL prolly ... he was free to install CM, GPE, AOSP, PACman and all these ROMs....so why flash it back to stock MK2? I mean, cutting his losses....that's funny...I mean, unless the MK2 OTA from AT&T came forced.... WHo knows...
He probably didn't know what he was doing, got stuck, and tried to Odin back to stock. Only he used the mk2 package and not the MDL one.
Stuff like that never surprises me anymore. People don't want to learn/read. Just give me the file so I can flash it.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app
joeybear23 said:
el o el
Click to expand...
Click to collapse
LOL my butt, buddy...we still have SafeStrap ....ab. 30+ ROMz for it...so not exactly eL Oh eL....but oh well....such is life, ya know?
Red_81 said:
He probably didn't know what he was doing, got stuck, and tried to Odin back to stock. Only he used the mk2 package and not the MDL one.
Stuff like that never surprises me anymore. People don't want to learn/read. Just give me the file so I can flash it.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I know EXACTLY what you mean, bud...just gimme the file so I can flash it -type ... who cares what's that gonna actually do to my phone...Oh well, there are people...and there's people.... U never know who you get to deal with....
Just ask for a little help, ...why is that so hard, right?
I've been reading up on all I could, and now that I "kinda" get a better understanding of how things lay with the i337 MK2...I can make a decision to flash, and stay stock...
Problem is, I have been flashing since 2009, so I can't imagine owning a droid, AND NOT FLASH IT!!! IT KINDA DEFEATS THE PURPOSE OF OWNING AN ANDROID, right? hehehe
I know that feeling. At least Safestrap is a decent option. I rushed out to grab my MDL 32gb one before they updated their stock.
Sent from my SAMSUNG-SGH-I337 using XDA Premium 4 mobile app
KK 4.4 NB1 baseband
John The Rhino said:
Answer, yes & yes. There is plenty of custom roms for mk2 in the All things mk2 guide. You can also upgrade to 4.4.2 Kit Kat now as well. Forget about MDL cause there's no way to go back to it.
Click to expand...
Click to collapse
***************************************
Yes, prolly could upgrade to 4.4 , but would be needing to flash the NB1 modem, baseband first right?
ANd ppl are saying there is not much SafeStrap versions for KK 4.4(.2) yet, or am I wrong?
DO you know any ROMz like that?
Would it be possible to come back to JB 4.3, once on KK, that you know of?
Lemme know, bud...THX
ANy links.....?
Okay, so I'm almost positive there is probably a thread for this, but I'm having trouble finding exactly what I'm looking for and very new to doing all of this on my own. I usually have a buddy help me out (aka he does it all).
I am running 4.4.2 Kit Kat on NC1 and I was finally able to root my device using TowelRoot. I've been trying for days now to install ClockworkMod custom recovery, but to no avail. Odin has failed, the command prompt method has failed, and Rom Manager app has failed. Is there just no compatible builds for any of this? I'm not entirely sure how this all works or why any of it is failing. What can I do to install CWM or TWRP and get CM11 back on? I need all kinds of explanation, so don't skimp on the details! Thanks guys!
You can't install clockwork. You have to use safestrap. Read the all things mk2, nc1 thread. It will tell you just about everything you need to know. Is an awesome thread and how I learned everything about this phone.
bweekzzzz said:
You can't install clockwork. You have to use safestrap. Read the all things mk2, nc1 thread. It will tell you just about everything you need to know. Is an awesome thread and how I learned everything about this phone.
Click to expand...
Click to collapse
Awesome! That's exactly the direction I'm looking for! Thank you so much.
No problem at all. We've all needed help on here from time to time. Good luck.
Great advice above. To add to it you will NOT be able to use CM11 on your device at this time or probably ever. Also you will NOT be able to ever flash CWM or TWRP recoveries.
You can ONLY use safestrap recovery which ONLY allows flashing Touchwiz based Roms.
You can ONLY flash Touchwiz based Roms because with Safestrap it will NOT flash any custom kernels. A custom Kernel is need to flash CM11, AOKP, and other AOSP Based roms.
You also CANNOT downgrade your bootloader as it is locked down hard. The locked down boot loader is why all above cannot work for your device. ONLY the original phones that came with MDB or MDL firmwares were able to use the Loki Bootloader Bypass, which allowed for flashing CWM or TWRP recoveries and then allow ANYTHING like any custom Roms (also based or Touchwiz based), flash custom kernels, flash anything. But any phone updated to the MF3 firmware or newer the boot loader was locked down too much to do much.
Sent fron I337 Red BadAss Themed ShoStock 7.0
I rooted my S4 ATT SGH-I337 yesterday with Kingroot while already having Lollipop 5.0.1. I then downloaded Flashify & Flashed ClockworkMod Recovery. Restarted my phone to goto recovery and I got a yellow triangle saying this phone has software unauthorized by att.
What Custom Recovery can I use and where can I find the latest version? Will TWRP work and also I've heard of something called Philz?
Oh and does bootloader have anything to do with this because when I rooted my S3 I never even knew or heard of bootloader.
Thanks in Advance
tpedreira said:
I rooted my S4 ATT SGH-I337 yesterday with Kingroot while already having Lollipop 5.0.1. I then downloaded Flashify & Flashed ClockworkMod Recovery. Restarted my phone to goto recovery and I got a yellow triangle saying this phone has software unauthorized by att.
What Custom Recovery can I use and where can I find the latest version? Will TWRP work and also I've heard of something called Philz?
Oh and does bootloader have anything to do with this because when I rooted my S3 I never even knew or heard of bootloader.
Thanks in Advance
Click to expand...
Click to collapse
You will not be able to use a custom recovery because your bootloader is locked with no means of unlocking it or downgrading to an unlocked one. You have 2 tools that you can use, currently in lollipop. One is flashfire beta. If you ever purchased mobile Odin, you will be upgraded to the paid version for free. The other is safestrap. Safestrap isn't updated for lollipop but there is a workaround. Since you rooted with Kingroot, I'd suggest getting flashfire beta and then use it to flash the rooted 0C3 zip found in the OP of this thread :
http://forum.xda-developers.com/gal...-to-update-to-i337oc3-5-0-1-keeproot-t3075814
The reason is that Kingroot seems shady and installs other crapware. Also, if you try to update to 0C4, it will fail with the Kingroot rooted lollipop. It won't with Muniz' method. Well, at least I know it won't with the stock rooted one. I'm still unsure if the deodexed one will cause the update to fail.
Snapping along on stock rooted 0C4 I337, wishing for some good up to date lollipop ROM's to throw into flashfire
I have Flashfire Pro and SuperSU
buggerritt said:
You will not be able to use a custom recovery because your bootloader is locked with no means of unlocking it or downgrading to an unlocked one. You have 2 tools that you can use, currently in lollipop. One is flashfire beta. If you ever purchased mobile Odin, you will be upgraded to the paid version for free. The other is safestrap. Safestrap isn't updated for lollipop but there is a workaround. Since you rooted with Kingroot, I'd suggest getting flashfire beta and then use it to flash the rooted 0C3 zip found in the OP of this thread :
http://forum.xda-developers.com/gal...-to-update-to-i337oc3-5-0-1-keeproot-t3075814
The reason is that Kingroot seems shady and installs other crapware. Also, if you try to update to 0C4, it will fail with the Kingroot rooted lollipop. It won't with Muniz' method. Well, at least I know it won't with the stock rooted one. I'm still unsure if the deodexed one will cause the update to fail.
Snapping along on stock rooted 0C4 I337, wishing for some good up to date lollipop ROM's to throw into flashfire
Click to expand...
Click to collapse
My question is what is 0C3? and what is 0C4?
I have the paid version of Flashfire beta
The reason I want a custom recovery is so i can make a backup of my phone and then flash a rom preferably Cyanogen Mod if they have it yet. I hate this touchwiz. But I wanna make a backup like i was able to wish Clockwork mod. Is FlashFire capable of making a complete backup? I see the Backup option but have no clue which to choose and or what it is backing up??????
tpedreira said:
My question is what is 0C3? and what is 0C4?
I have the paid version of Flashfire beta
The reason I want a custom recovery is so i can make a backup of my phone and then flash a rom preferably Cyanogen Mod if they have it yet. I hate this touchwiz. But I wanna make a backup like i was able to wish Clockwork mod. Is FlashFire capable of making a complete backup? I see the Backup option but have no clue which to choose and or what it is backing up??????
Click to expand...
Click to collapse
OC3 is the original Lollipop distribution for the AT&T I337. OC4 is the patch update which is assumed to have corrected the stagefright bug.
I don't have the phone, so I don't use flashfire, but I understand that you can do most everything with it that you can do with CWM or TWRP.
The bootloader is locked, and you will not be able to install a custom recovery. You will also not be able to install a custom kernel, so no AOSP based roms can be installed either. You're stuck with Touchwiz based roms. Period.
TWRP will work
Anili9082 said:
TWRP will work
Click to expand...
Click to collapse
No it won't. Only safestrap will work with the nc1 work around. Flashfire is great until you want to flash a rom with an aroma installer, then safestrap is the only option.
Can't upgrade to OC4
Hey, I have updated to Lollipop using Muniz's method back in April. You said that the udate should work with Muniz's installation. It is not working for me. Are you aware of this? I too have a locked bootloader, and am stuck with the Safestrap like many others.
Thanks,
buggerritt said:
You will not be able to use a custom recovery because your bootloader is locked with no means of unlocking it or downgrading to an unlocked one. You have 2 tools that you can use, currently in lollipop. One is flashfire beta. If you ever purchased mobile Odin, you will be upgraded to the paid version for free. The other is safestrap. Safestrap isn't updated for lollipop but there is a workaround. Since you rooted with Kingroot, I'd suggest getting flashfire beta and then use it to flash the rooted 0C3 zip found in the OP of this thread :
http://forum.xda-developers.com/gal...-to-update-to-i337oc3-5-0-1-keeproot-t3075814
The reason is that Kingroot seems shady and installs other crapware. Also, if you try to update to 0C4, it will fail with the Kingroot rooted lollipop. It won't with Muniz' method. Well, at least I know it won't with the stock rooted one. I'm still unsure if the deodexed one will cause the update to fail.
Snapping along on stock rooted 0C4 I337, wishing for some good up to date lollipop ROM's to throw into flashfire
Click to expand...
Click to collapse
hi4s4 said:
Hey, I have updated to Lollipop using Muniz's method back in April. You said that the udate should work with Muniz's installation. It is not working for me. Are you aware of this? I too have a locked bootloader, and am stuck with the Safestrap like many others.
Thanks,
Click to expand...
Click to collapse
Have you changed anything since the update? If you've unistalled or frozen any apps, or made any other change to the rom, the update will fail. It does work with the deodexed version of the rom also, that's what I updated with.
i have rooted OC4 installed on my phone and have i've been reading up on OCTos and their 6.0.1 custom firmware (found a good link too: http://www.teamandroid.com/2016/01/20/update-att-galaxy-s4-i337-android-601-octos-marshmallow-custom-rom/ ) . and now am more confused.
it should be simple from what i am reading.
1) backup everything
2) revert to 4.3 (mk2), root, and install ClockworkMod 10.2+
3) install custom rom 6.0.1 OCTos
however, i'm reading on this page (http://forum.xda-developers.com/galaxy-s4-att/general/guide-odin-to-stock-updating-rooting-t2926642) but it states >> Once you flash NB1, you CANNOT go back to MK2. <<
So now I'm trying to figure out exactly how i can get the OCTos onto my phone. what guide should i follow !?!?!?!
:silly:
They meant the MK2 boot loader based devices, same with MDL. Aside from a few exploited boot loaders.. it's been the general consensus that they're all locked up, therefore.. only stock roms. The lowest boot loader you can possibly be on is NB1. Download "Terminal Emulator" for the Play Store and then when you open it up, type the following:
getprop ro.bootloader
^ exactly like that, then see what it says. The last three characters (MDK, MDL, MK2, NB1, NC1, OC3, OC4)--that's how you can figure out which boot loader you are using. I am on NB1's bootloader but I can still downgrade to MK2, i.e. Android 4.3, and still have it work.. only because of how the roms in these threads are rooted and the fact that they're stock, aside from a few other small details. When they say OC3 or MK2, or NB1... whichever.. then typically they mean the boot loader when saying you cannot revert. Definitely cannot revert to MK2 bootloader after taking an OTA update.
pr3dicament said:
getprop ro.bootloader
Click to expand...
Click to collapse
i337ucugoc4
egiblock said:
i have rooted OC4 installed on my phone and have i've been reading up on OCTos and their 6.0.1 custom firmware (found a good link too: http://www.teamandroid.com/2016/01/20/update-att-galaxy-s4-i337-android-601-octos-marshmallow-custom-rom/ ) . and now am more confused.
it should be simple from what i am reading.
1) backup everything
2) revert to 4.3 (mk2), root, and install ClockworkMod 10.2+
3) install custom rom 6.0.1 OCTos
however, i'm reading on this page (http://forum.xda-developers.com/galaxy-s4-att/general/guide-odin-to-stock-updating-rooting-t2926642) but it states >> Once you flash NB1, you CANNOT go back to MK2. <<
So now I'm trying to figure out exactly how i can get the OCTos onto my phone. what guide should i follow !?!?!?!
:silly:
Click to expand...
Click to collapse
Even though it was not mentioned, the article appears to be written for the SGH-i337 with old bootloaders (MDB, MDL). These are the only two bootloaders that can be exploited and installed the custom recovery like CWM or TWRP.
Since your bootloader is OC4 you can not install the CWM or TWRP. You could try flashing with safestrap though. If that custom rom is not written with Aroma then you could also try to flash with flashfire. These are the only two options for you.
egiblock said:
i337ucugoc4
Click to expand...
Click to collapse
Okay, yeah.. you're not on MDK or MDL, not even NB1.. you're simply on OC4. You aren't going to be able to do any flashing of any Custom Roms that are not Safestrap compatible (touchwiz)
Good luck.. you can't go anywhere backwards, not even OC3. That really sucks. I'm sorry. It looks like you took the OTA's.
I can still ODIN to NB1 and that was because I never took the OTA update. I got lucky.. I can still choose between kitkat and lollipop. You can't. You might be able to with someone's help.. but your bootloader is OC4.. that's a problem. You more than likely will have trouble doing anything unless it's not MDK/MDL or even NB1 based.
---------- Post added at 08:23 PM ---------- Previous post was at 08:21 PM ----------
sway8966 said:
Even though it was not mentioned, the article appears to be written for the SGH-i337 with old bootloaders (MDB, MDL). These are the only two bootloaders that can be exploited and installed the custom recovery like CWM or TWRP.
Since your bootloader is OC4 you can not install the CWM or TWRP. You could try flashing with safestrap though. If that custom rom is not written with Aroma then you could also try to flash with flashfire. These are the only two options for you.
Click to expand...
Click to collapse
Yeah.. You might have a shot with FlashFire. I might test that via the NB1 bootloader that I'm on but I don't think it matters that much aside from being able to Odin back to 4.3 software.
sway8966 said:
Even though it was not mentioned, the article appears to be written for the SGH-i337 with old bootloaders (MDB, MDL). These are the only two bootloaders that can be exploited and installed the custom recovery like CWM or TWRP.
Since your bootloader is OC4 you can not install the CWM or TWRP. You could try flashing with safestrap though. If that custom rom is not written with Aroma then you could also try to flash with flashfire. These are the only two options for you.
Click to expand...
Click to collapse
FlashFire came out with another release (0.32) that seems to have an AROMA emulation option.. my guess is that it's still in testing, but it's worth a shot even without it. The way I have OC3 with the NB1 boot loader is because of FlashFire.. Safestrap.. it's been awhile since I've used it. I've tried recently for other ROMS but you can't do a custom kernel.. that's the reason most custom roms aren't able to work, i.e. CM v13 runs a totally different kernel. It's not just TouchWiz now.. now it's just stock kernels.. at least via SafeStrap. So far I've gotten none to work with SafeStrap aside from Stock rooted roms. OC3, OC4, and if I felt like it, OK2.. but why even bother with OK2, I'm not gonna see any difference given all of the patches you can use with Xposed.. including any memory leak bull****, that's all good now in 5.0.x -- 5.1+ has that patched up.. and OK2 certainly isn't 5.1. I don't see any difference between OC3 and OC4.. and if my opinion counts for anything.. the one thing that I noticed (bloatware script ran and other apps not needed were frozen for both) is a very high amount of battery usage with OC4.. same userdata, same everything.. and when you flash the kernel, the modules, and move up to OC4.. it's still the same looking.. feels the same.. more ram used.. OC3 is superior in this instance. I'd love to try and give an AOSP rom a shot.. but.. via SafeStrap (someone made a guide for those not on the MDK or MDL boot loaders) .. eh.. no luck. That was all via SafeStrap. I'm just putting in my two cents. I think development for this phone is finished.. no one has come out with anything new aside from the SafeStrap kernel workarounds.. not many FlashFire users.. and the one that used to find every single exploit is now EMPLOYED by Samsung so his development.. gone. That was a huge kick in the ass to this entire community. Plenty of people around, just.. they don't give a **** about the S4 with boot loader all locked up. NB1 was an accident for me.. I was on MDL for a long, long time.. I really ****ed that up or I'd be running MarshMallow already It seems to run best with KitKat, but a lot of AOSP roms have shown huge differences in MarshMallow.. oh well. Can't try it at the moment.
Unfortunately I can't remember what I did in the past to this phone, but I have never had luck with OTA updates. I'll have to see if I can find my note to see what I originally did on this stupid thing.
egiblock said:
Unfortunately I can't remember what I did in the past to this phone, but I have never had luck with OTA updates. I'll have to see if I can find my note to see what I originally did on this stupid thing.
Click to expand...
Click to collapse
Since you are on OC4, the lowest you can go is NB1 (kit-kat).