Database Users

How to uninstall CWM from Huawei P8, B200, rolled back from MM

I don't have an unlocked bootloader and i flashed the CWM. Now when i try to enter the recovery mode with buttons, nothing happens just turns the phone on normally. I searched for stock recoveries, but didn't found nothing.
I have GRA-L09, B200, Europe Open
Thanks for help!

To get an unlocked bootloader you must go to settings> about phone> build number
and then press build number 7 times
after you did that exit out of about phone then click on the newly-appeared 'developer settings'
there you should find OEM Unlocking and Enable USB Debugging
You'll get it from there.

I have the Dev Ops, but don't have OEM unlock.

But shouldn't you already have an unlocked bootloader to have DevOps?

Don't know. I don't typed any code in to unlock bootloader.

Are you sure you have DevOps?
---------- Post added at 01:58 PM ---------- Previous post was at 01:55 PM ----------
And also try to do it not with buttons, but with your computer
I don't know the script for how to boot into recovery mode but to fastboot, for example, you'd type in >fastboot
when your phone is connected to your PC via USB.
Y'know, just search up 'How to use Recovery Mode' - maybe you just did it wrong

Didn't tryed it w/ adb yet.

ADB didn't worked. I'm trying a full hard reset..

Hard reset didn't do nothing. HELP PLS!!

adb reboot-bootloader worked, but it has a subtitle: Phone Locked (with red). What is it?

TheGolem said:
adb reboot-bootloader worked, but it has a subtitle: Phone Locked (with red). What is it?
Click to expand...
Click to collapse
That means you have a locked bootloader, so CWM didn't install successfully.
In other words, you need to unlock the bootloader first in order to successfully install CWM.
So, 1st step - visit the Huawei unlocking code request page, taking your time to fill in the form accurately & submit it.
[Btw, if you don't already have a Huawei ID, you can register for one here: http://www-file.huawei.com/en/my-huawei/register
Then use these login details in the above link to request for the unlock code]
2nd step: Once you receive the unlock code from them, use it to unlock the bootloader by issuing the following command in fastboot mode [the asterisks (*) represent your 16-digit unlock code]:
Code:
fastboot oem unlock ****************
Now you can attempt to install CWM. Where are you getting the CWM img file from?

GaT7 said:
That means you have a locked bootloader, so CWM didn't install successfully.
In other words, you need to unlock the bootloader first in order to successfully install CWM.
So, 1st step - visit the Huawei unlocking code request page, taking your time to fill in the form accurately & submit it.
[Btw, if you don't already have a Huawei ID, you can register for one here: http://www-file.huawei.com/en/my-huawei/register
Then use these login details in the above link to request for the unlock code]
2nd step: Once you receive the unlock code from them, use it to unlock the bootloader by issuing the following command in fastboot mode [the asterisks (*) represent your 16-digit unlock code]:
Code:
fastboot oem unlock ****************
Now you can attempt to install CWM. Where are you getting the CWM img file from?
Click to expand...
Click to collapse
Sorry, "Phone Unlocked" with red

TheGolem said:
Sorry, "Phone Unlocked" with red
Click to expand...
Click to collapse
Ok, so it appears you may have corrupted the recovery partition.
Is the phone otherwise booting into the system & functioning normally?
Also, can you tell us what you are wanting to ultimately achieve by installing CWM?
Just to confirm the bootloader is unlocked, run this command in fastboot mode & let us know the result:
Code:
fastboot oem get-bootinfo

Ok, I just read your post in the other thread about wanting to update B200 to B370.
TheGolem said:
I have b200 but can't install it [B370]. Why?
Early flashed the CWM with flashify succesfully, but don't have unlocked bootloader. And if i try to enter recovery mode, nothing happens. Is it possible, that i cant' install it because of this?
Click to expand...
Click to collapse
As the guys already said, you do not need to install anything in order to update an official rom.
So, let's leave out CWM, bootloaders, etc for now, & help you update only from B200.
When you try using TopperBG's method to update, what happens?
What is your current FULL firmware version? It will be in this format: GRA-L09CxxxB200 - if everything else is as I've mentioned, I'm interested in the Cxxx part.

GaT7 said:
Ok, I just read your post in the other thread about wanting to update B200 to B370.
As the guys already said, you do not need to install anything in order to update an official rom.
So, let's leave out CWM, bootloaders, etc for now, & help you update only from B200.
When you try using TopperBG's method to update, what happens?
What is your current FULL firmware version? It will be in this format: GRA-L09CxxxB200 - if everything else is as I've mentioned, I'm interested in the Cxxx part.
Click to expand...
Click to collapse
Update succeed, it wroks fine. The problem is with the recovery mode.
When i'm trying the button method to enter recover, the phone just normally turns on. When still hold the buttons, black screen. It's with the abd too.

TheGolem said:
adb reboot-bootloader worked, but it has a subtitle: Phone Locked (with red). What is it?
Click to expand...
Click to collapse
you don't have a unlocked bootloader so you can't have cwm

I said it wrong:
-Android 5 succeed
-If i try to install Android 6
https://forum.xda-developers.com/huawei-p8/how-to/emui4-0-1-p8-official-marshmallow-6-0-t3417212
or enter recovery mode, then happens the black screen.

TheGolem said:
I said it wrong:
-Android 5 succeed
-If i try to install Android 6
https://forum.xda-developers.com/huawei-p8/how-to/emui4-0-1-p8-official-marshmallow-6-0-t3417212
or enter recovery mode, then happens the black screen.
Click to expand...
Click to collapse
1. You need to install stock recovery for android 5(unlocked bootloader is required).
2. Then you can use the dload method to update.
3. You can flash TWRP after that because no-one uses CWM.

GaT7 said:
Ok, so it appears you may have corrupted the recovery partition.
Is the phone otherwise booting into the system & functioning normally?
Also, can you tell us what you are wanting to ultimately achieve by installing CWM?
Just to confirm the bootloader is unlocked, run this command in fastboot mode & let us know the result:
Code:
fastboot oem get-bootinfo
Click to expand...
Click to collapse
Phone normally booting, no problem with current system.
I typed in the command, and its <waiting for device>.

GaT7 said:
Where are you getting the CWM img file from?
Click to expand...
Click to collapse
http://www.teamandroid.com/2015/06/07/install-huawei-p8-clockworkmod-recovery/2/
Step 5
cwm-p8-nogui.img

Boot loop after Android O DP2 update

I installed Android O DP2 update via OTA yesterday. The phone updated, rebooted to the new build and restarted abruptly and since then has been stuck in a boot loop. The Google logo shows up, goes to the android animation step and then Google logo appears again.
I don't have bootloader unlocked, don't have TWRP and have done OTA updates. I am able to get into the stock recovery mode.
How do I fix this, i.e. make it work in any way without erasing the user data? I don't mind extreme steps (without erasing user data) because I was planning to reflash 7 with unlocking & rooting today.

Try to wipe cache from recovery - in recovery hold volume-down and select "Wipe cache partition". Should do the trick

I tried, didn't work. Had to factory reset in the end. Also opted out of beta

I just read that some people that took the update from certain builds had boot loops due to the update only replacing part of the OS but leaving the 7.x.x system in place causing it to boot loop. I think it was like on android authority or something like that.
Sent from my Nexus 6P using XDA-Developers Legacy app

I have similar problem. Phone became stuck at Google logo and bootloop. I didn't have OEM unlock and debugged enable when phone was working. Now I'm stuck because It cannot flash with any factory image rom. Anyone with solution, please help. Thanks

citifone said:
I have similar problem. Phone became stuck at Google logo and bootloop. I didn't have OEM unlock and debugged enable when phone was working. Now I'm stuck because It cannot flash with any factory image rom. Anyone with solution, please help. Thanks
Click to expand...
Click to collapse
You can unlock your bootloader to flash a stock ROM. Do you need the steps?
---------- Post added at 09:54 AM ---------- Previous post was at 09:38 AM ----------
citifone said:
I have similar problem. Phone became stuck at Google logo and bootloop. I didn't have OEM unlock and debugged enable when phone was working. Now I'm stuck because It cannot flash with any factory image rom. Anyone with solution, please help. Thanks
Click to expand...
Click to collapse
To flash a system image:
Download the latest system image for your Nexus 6p, then unzip it to a safe directory.
https://dl.google.com/dl/android/aosp/angler-n2g47o-factory-dc258043.zip
or Download any of your choice from here
https://developers.google.com/android/images
Connect your device to your computer over USB.
Start the device in fastboot mode with one of the following methods:
adb tool
http://developer.android.com/tools/help/adb.html
Using a key combo: Turn the device off, then turn it on and immediately hold down the relevant key combination for your device.
POWER BUTTON + VOLUME DOWN BUTTON
Click to expand...
Click to collapse
If necessary, unlock the device's bootloader using one of the following methods:
Code:
fastboot flashing unlock
If you are updating an older device, run this command:
Code:
fastboot oem unlock
The target device will show you a confirmation screen. (This erases all data on the target device.)
Open a terminal and navigate to the unzipped system image directory or Open a command prompt from within your System image folder (navigate to where you have flash-all.bat located on your PC, shift + right click anywhere within that folder, select open command prompt here
Execute the flash-all script.
Code:
fastboot flash-all.bat
This script installs the necessary bootloader, baseband firmware(s), and operating system.
Once the script finishes, your device reboots. You should now lock the bootloader for security:
Start the device in fastboot mode again, as described above.
Execute:
Code:
fastboot flashing lock
or, for older devices, run:
Code:
fastboot oem lock
Locking bootloader will wipe the data on some devices. After locking the bootloader, if you want to flash the device again, you must run fastboot oem unlock again, which will wipe the data.

Mavelos said:
You can unlock your bootloader to flash a stock ROM. Do you need the steps?
---------- Post added at 09:54 AM ---------- Previous post was at 09:38 AM ----------
To flash a system image:
Download the latest system image for your Nexus 6p, then unzip it to a safe directory.
https://dl.google.com/dl/android/aosp/angler-n2g47o-factory-dc258043.zip
or Download any of your choice from here
https://developers.google.com/android/images
Connect your device to your computer over USB.
Start the device in fastboot mode with one of the following methods:
adb tool
http://developer.android.com/tools/help/adb.html
Using a key combo: Turn the device off, then turn it on and immediately hold down the relevant key combination for your device.
If necessary, unlock the device's bootloader using one of the following methods:
Code:
fastboot flashing unlock
If you are updating an older device, run this command:
Code:
fastboot oem unlock
The target device will show you a confirmation screen. (This erases all data on the target device.)
Open a terminal and navigate to the unzipped system image directory or Open a command prompt from within your System image folder (navigate to where you have flash-all.bat located on your PC, shift + right click anywhere within that folder, select open command prompt here
Execute the flash-all script.
Code:
fastboot flash-all.bat
This script installs the necessary bootloader, baseband firmware(s), and operating system.
Once the script finishes, your device reboots. You should now lock the bootloader for security:
Start the device in fastboot mode again, as described above.
Execute:
Code:
fastboot flashing lock
or, for older devices, run:
Code:
fastboot oem lock
Locking bootloader will wipe the data on some devices. After locking the bootloader, if you want to flash the device again, you must run fastboot oem unlock again, which will wipe the data.
Click to expand...
Click to collapse
Thanks for your reply..But you can only do this only if you have an unlocked bootloader and debugged mode on. I didn't have either so it won't allow to flash with locked bootloader.

citifone said:
Thanks for your reply..But you can only do this only if you have an unlocked bootloader and debugged mode on. I didn't have either so it won't allow to flash with locked bootloader.
Click to expand...
Click to collapse
Exactly why i posted that. You can unlock your bootloader without turning USB debugging ON. Just Boot up with the POWER + VOLUME down Combination and use the bootloader unlock command in my previous post.

FAILED (remote: OEM unlock is not allowed)
Mavelos said:
Exactly why i posted that. You can unlock your bootloader without turning USB debugging ON. Just Boot up with the POWER + VOLUME down Combination and use the bootloader unlock command in my previous post.
Click to expand...
Click to collapse
What I think he is telling you and the same problem I have, when We try the unlock command we are getting this error :
FAILED (remote: OEM unlock is not allowed)
any suggestions ?
Regards.

Lord Aguacate said:
What I think he is telling you and the same problem I have, when We try the unlock command we are getting this error :
FAILED (remote: OEM unlock is not allowed)
any suggestions ?
Regards.
Click to expand...
Click to collapse
Yes, I got the same error. Again, it's because of bootloader locked and debug is off. Any other ways to unlock or flash this phone?

citifone said:
Yes, I got the same error. Again, it's because of bootloader locked and debug is off. Any other ways to unlock or flash this phone?
Click to expand...
Click to collapse
To unlock you first need to have ticked the allow OEM unlock from developer menu within the OS. It won't work otherwise.

Lord Aguacate said:
What I think he is telling you and the same problem I have, when We try the unlock command we are getting this error :
FAILED (remote: OEM unlock is not allowed)
any suggestions ?
Regards.
Click to expand...
Click to collapse
You'll have to use a Rescue OTA
Download the latest Nexus 6P OTA from here https://dl.google.com/dl/android/aosp/angler-ota-n2g47o-ec3f4df1.zip
STEPS TO FOLLOW
To apply an OTA update image:
Download the appropriate update image for your device below.
https://dl.google.com/dl/android/aosp/angler-ota-n2g47o-ec3f4df1.zip
Boot into your recovery from fastboot
use the key combination for your device
Code:
POWER + VOLUME DOWN
and then select the Recovery option from the bootloader menu. The device is now in recovery mode and an Android logo with red exclamation mark should appear on screen.
Hold the Power button and press Volume Up once, and a menu will appear. Select the option Apply update from ADB.
Run the following command on your PC:
Code:
adb devices
and check that your device shows up with "sideload" next to its name.
Run the following command:
Code:
adb sideload ota_file.zip
where ota_file.zip is the name of the file you have downloaded and verified.
Once the update finishes, reboot the phone by choosing Reboot system now.

Mavelos said:
You'll have to use a Rescue OTA
Download the latest Nexus 6P OTA from here [="https://dl.google.com/dl/android/aosp/angler-ota-n2g47o-ec3f4df1.zip"]https://dl.google.com/dl/android/aosp/angler-ota-n2g47o-ec3f4df1.zip
STEPS TO FOLLOW
To apply an OTA update image:
Download the appropriate update image for your device below.
="https://dl.google.com/dl/android/aosp/angler-ota-n2g47o-ec3f4df1.zip"]https://dl.google.com/dl/android/aosp/angler-ota-n2g47o-ec3f4df1.zip
Boot into your recovery from fastboot
use the key combination for your device
Code:
POWER + VOLUME DOWN
and then select the Recovery option from the bootloader menu. The device is now in recovery mode and an Android logo with red exclamation mark should appear on screen.
Hold the Power button and press Volume Up once, and a menu will appear. Select the option Apply update from ADB.
Run the following command on your PC:
Code:
adb devices
and check that your device shows up with "sideload" next to its name.
Run the following command:
Code:
adb sideload ota_file.zip
where ota_file.zip is the name of the file you have downloaded and verified.
Once the update finishes, reboot the phone by choosing Reboot system now.
Click to expand...
Click to collapse
Dear Mavelos,
I already tried that and the installation was successful, but my first problem still there, when I installed the Android O Beta, the touch of my screen stop working after the 2nd day of installation.
Now I don't know if this is a problem with Android O or just a coincidence and the hardware its broken.
I went to a lot of forums but nobody its talking about that (Touch Screen not working)
Did You guys hear anything about it?

Mavelos said:
You'll have to use a Rescue OTA
Download the latest Nexus 6P OTA from here https://dl.google.com/dl/android/aosp/angler-ota-n2g47o-ec3f4df1.zip
STEPS TO FOLLOW
To apply an OTA update image:
Download the appropriate update image for your device below.
https://dl.google.com/dl/android/aosp/angler-ota-n2g47o-ec3f4df1.zip
Boot into your recovery from fastboot
use the key combination for your device
Code:
POWER + VOLUME DOWN
and then select the Recovery option from the bootloader menu. The device is now in recovery mode and an Android logo with red exclamation mark should appear on screen.
Hold the Power button and press Volume Up once, and a menu will appear. Select the option Apply update from ADB.
Run the following command on your PC:
Code:
adb devices
and check that your device shows up with "sideload" next to its name.
Run the following command:
Code:
adb sideload ota_file.zip
where ota_file.zip is the name of the file you have downloaded and verified.
Once the update finishes, reboot the phone by choosing Reboot system now.
Click to expand...
Click to collapse
I have the same problem as others, stuck in a bootloop and had not enabled unlock in dev options. I can get to bootloader but not recovery mode (bootloops when I select this). I would love to try this OTA side load, but I can't see my device in adb. I can see it however in fastboot. Not sure how to get it up in adb....
Any help would be much appreciated.

scorneil said:
I have the same problem as others, stuck in a bootloop and had not enabled unlock in dev options. I can get to bootloader but not recovery mode (bootloops when I select this). I would love to try this OTA side load, but I can't see my device in adb. I can see it however in fastboot. Not sure how to get it up in adb....
Any help would be much appreciated.
Click to expand...
Click to collapse
If you get a bootloop when selecting recovery, try rebooting to recovery with fastboot
Code:
fastboot reboot recovery
if that doesn't work, then i think your device is bricked.
---------- Post added at 06:19 AM ---------- Previous post was at 06:16 AM ----------
Lord Aguacate said:
Dear Mavelos,
I already tried that and the installation was successful, but my first problem still there, when I installed the Android O Beta, the touch of my screen stop working after the 2nd day of installation.
Now I don't know if this is a problem with Android O or just a coincidence and the hardware its broken.
I went to a lot of forums but nobody its talking about that (Touch Screen not working)
Did You guys hear anything about it?
Click to expand...
Click to collapse
If your touch screen isn't working, it might be related to the Android O Beta you flashed. Can you boot the phone up? If you have an OTG cable, connect a mouse to your phone. Turn on OEM unlocking in developer options. Do a factory reset.

i have the same problem with this, and i cannot unlock it too, is there anyway to unlock this phone?

OTG works Perfect! But.....
Mavelos said:
If you get a bootloop when selecting recovery, try rebooting to recovery with fastboot
Code:
fastboot reboot recovery
if that doesn't work, then i think your device is bricked.
---------- Post added at 06:19 AM ---------- Previous post was at 06:16 AM ----------
If your touch screen isn't working, it might be related to the Android O Beta you flashed. Can you boot the phone up? If you have an OTG cable, connect a mouse to your phone. Turn on OEM unlocking in developer options. Do a factory reset.
Click to expand...
Click to collapse
So I Follow your suggestion and I bought the OTG adapter, works perfectly I unlocked the bootloader from the developers options, did a factory restore with a previous image, etc.... Touch still not working, I'm starting to believe this a hardware problem with the screen.... Bad Luck maybe, I don't know! ..... I will have to buy that expensive screen ($140).
Anyway thanks for the help...
Regards

Lord Aguacate said:
So I Follow your suggestion and I bought the OTG adapter, works perfectly I unlocked the bootloader from the developers options, did a factory restore with a previous image, etc.... Touch still not working, I'm starting to believe this a hardware problem with the screen.... Bad Luck maybe, I don't know! ..... I will have to buy that expensive screen ($140).
Anyway thanks for the help...
Regards
Click to expand...
Click to collapse
You're welcome. Get your phone fixed and return to the flashing community.

last night i my phone inside my freezer hehehe and this morning i tried to turn it on, and it pass the google logo boot normally but it only lasted for a few minute and then turn off and bootloop again. so i guess my 6p has a hardware faulty

----- Root Moto M S356 Android 7 -------

Hi guys,
I have started this thread so that you guys can root your moto M XT_1663_S356 andriod (7.0)
First of all i'm not responsible if your phone bricks burns or dies.
A big thanks to VVizard from lenovo RU forum with out him, it was not possible.
Thanks to Chainfire for the SuperSu.zip
To check Build number go to Settings -> About Phone-> Build number
Note -
1 - This only works for Moto M which is having build number XT1663_S356_170621_ROW. If you are on any other build number then please don't proceed.
2 - All the files are attached
3 - Install all the Motoral drivers and Minimal and adb folder.
4 - Following link contains all files needed to root the phone.
https://drive.google.com/file/d/0B3eDb0dWRU-uUjk4ZS1tdFpRR1U/view?usp=sharing
Rooting Moto M phone is divided into 3 Parts
1) Unlocking BootLoader
2) Flashing TWRP
3) Flashing SuperSu.zip
unlocking the bootloader
Note - This will wipe out all the data hence take a backup before unlocking boot loader
1 - First of all enable the Developer Option, To Enable the Developer Option, Go to your Settings -> About Phone-> Now Tap on the Build Number 7-8 Times until you see a toast message “Developer option enabled"
2 - Go back to settings -> Now you need to enable the OEM Unlock by going to Settings -> Developer Option and Enable OEM Unlock and USB Debugging
3 - Download and Extract the Downloaded ADB fastboot Zip file on your PC
4 - Now connect your phone to Computer using USB Cable.
5 - When you connect your Phone to Computer, please wait until all the drivers get installed.
6 - In your ADB fastboot folder open a command prompt window by pressing Shift Key + Right Mouse Click
7 - Now type the command in your command window
adb devices
If you see a pop up to allow USB Debugging on your phone, Click OK
8 - Now type the command below to reboot your phone to bootloader
adb reboot bootloader
9 - Once your phone reboot into bootloader, then type the command below to make sure fastboot drivers are installed properly.
fastboot devices
10 - This command will list the connected devices. If your phone’s serial number shows up you are good to go and may continue. If the phone is NOT listed this indicates that your drivers are not installed correctly.
11 - If your phone is listed then type in the following command in CMD.
fastboot oem unlock
12 - Check your phone you would have written"do you really want to unloock bootloader ? "(something like this). Just select yes using volume up and down button and press power button to confirm it .
13 - Congrats your bootloader is unlocked
Install TWRP
Note - You should have your bootloader unlocked before proceeding.
Copy the boot_XT1663_356.img and TWRP_Moto_M.img to Minimal adb folder
1 - First of all enable the Developer Option, To Enable the Developer Option, Go to your Settings -> About Phone-> Now Tap on the Build Number 7-8 Times until you see a toast message “Developer option enabled"
2 - Go back to settings -> Now you need to enable the OEM Unlock by going to Settings -> Developer Option and Enable OEM Unlock and USB Debugging
3 - Download and Extract the Downloaded ADB fastboot Zip file on your PC
4 - Now connect your phone to Computer using USB Cable.
5 - When you connect your Phone to Computer, please wait until all the drivers get installed.
6 - In your ADB fastboot folder open a command prompt window by pressing Shift Key + Right Mouse Click
7 - Now type the command in your command window
adb devices
If you see a pop up to allow USB Debugging on your phone, Click OK
8 - Now type the command below to reboot your phone to bootloader
adb reboot bootloader
9 - Once your phone reboot into bootloader, then type the command below to make sure fastboot drivers are installed properly.
fastboot devices
10 - This command will list the connected devices. If your phone’s serial number shows up you are good to go and may continue. If the phone is NOT listed this indicates that your drivers are not installed correctly.
11 - If your phone is listed then type in the following command in CMD.
fastboot flash boot boot_XT1663_356.img
12 - To flash the recovery, Type the command
fastboot flash recovery TWRP_Moto_M.img
13 - Congrats! you have successfully installed TWRP.
Rooting Phone.
Note -
You should have your bootloader unlocked.
You should have TWRP installed.
You should have supersu.zip copied in your phone.
1 - Switch off your phone. Now press volume down + power button till phone vibrates. Once it vibrates release the power button you should see android logo.
2 - Now with the help of volume up and down button select 'Recovery mode' and press power button.
3 - TWRP should start up.
4 - Select 'Allow Modification' and proceed.
5 - Select 'Install' and then select the 'SuperSu.zip' file and flash it.
6 -Restart the Phone.
7 - Congrats! your phone is rooted.
Note -
I have tried all this steps and have successfully rooted my phone i'm not responsible for any damage.
I have not build the boot_M_S365/ img file this is done by VVizard and really very thank full to him.

I am making a video on this!

Method Issues
Bro, I have faced a few problems since I have started
i) When I type in adb devices it shows my phone but unauthorized
so I have to allow it as you said but only after a reboot and doing the process again will it show authorized
ii) after entering adb reboot bootloader it doesnt show bootloader locked but straight up fastboot mode
iii) then when i enter fastboot oem unlock it shows asks me if I want to unlock, I press on volume up. Then it again asks me some other thing and I hold the volume up down and power together. Next I reboot into my phone. All data erased. I setup it again.
Now, does this mean my bootloader is unlocked? When I reboot it shows something on the middle right- unlocked..
So does this mean I continue and install twrp now? or what?

manandua01 said:
Thanks bro, I will give you credits ^_^
Click to expand...
Click to collapse
Cool!

manandua01 said:
Bro, I have faced a few problems since I have started
i) When I type in adb devices it shows my phone but unauthorized
so I have to allow it as you said but only after a reboot and doing the process again will it show authorized
ii) after entering adb reboot bootloader it doesnt show bootloader locked but straight up fastboot mode
iii) then when i enter fastboot oem unlock it shows asks me if I want to unlock, I press on volume up. Then it again asks me some other thing and I hold the volume up down and power together. Next I reboot into my phone. All data erased. I setup it again.
Now, does this mean my bootloader is unlocked? When I reboot it shows something on the middle right- unlocked..
So does this mean I continue and install twrp now? or what?
Click to expand...
Click to collapse
1 - It doen't matter if its authorized or not..
2 - yes! thats correct it directly takes you to fastboot mode it use to show bootloader locked for old Moto phones).I 'll make changes in the thread.
Yes! your bootloader is unlocked successfully..
if you see something like 'Your devices is unlocked and cant be trusted' on the left hand side during the moto logo.

TWRP Recovery
akash.mahadeshwar said:
1 - It doen't matter if its authorized or not..
2 - yes! thats correct it directly takes you to fastboot mode it use to show bootloader locked for old Moto phones).I 'll make changes in the thread.
Yes! your bootloader is unlocked successfully..
if you see something like 'Your devices is unlocked and cant be trusted' on the left hand side during the moto logo.
Click to expand...
Click to collapse
Thanks for your help Y_Y
Hey bro, I am not about to install the recovery.
Before this may I ask why we need to flash boot_XT1663_356.img ?
Also, isn't this command wrong? fastboot flash boot boot_XT1663_356.img
It should be fastboot flash boot boot_XT1663_356.img
Without the boot twice ryt?
Also, will the data be erased after installing TWRP recovery or not? If not, will it be erased after installing the SuperSU?

manandua01 said:
Thanks for your help Y_Y
Hey bro, I am not about to install the recovery.
Before this may I ask why we need to flash boot_XT1663_356.img ?
Also, isn't this command wrong? fastboot flash boot boot_XT1663_356.img
It should be fastboot flash boot boot_XT1663_356.img
Without the boot twice ryt?
Also, will the data be erased after installing TWRP recovery or not? If not, will it be erased after installing the SuperSU?
Click to expand...
Click to collapse
1 - It is the Image file which is specifically build for S356 (build number) hence it is necessary to flash it before flashing TWRP. If you don't flash boot image then you might face boot loop issues and hard brick your phone.
2 - The correct command is 'fastboot flash boot boot_XT1663_356.img' . the first boot is to recognize cmd that we are flashing a boot image and the second boot is the name of image file.
3 - Flashing TWRP and Super SU won't erase your data.

akash.mahadeshwar said:
1 - It is the Image file which is specifically build for S356 (build number) hence it is necessary to flash it before flashing TWRP. If you don't flash boot image then you might face boot loop issues and hard brick your phone.
2 - The correct command is 'fastboot flash boot boot_XT1663_356.img' . the first boot is to recognize cmd that we are flashing a boot image and the second boot is the name of image file.
3 - Flashing TWRP and Super SU won't erase your data.
Click to expand...
Click to collapse
I installed TWRP unlocked bootloader copied SuperSU- and was abt to root. With volume up and down I came to Factory Mode
It said Factory Mode
I pressed on power button- now it shows something in Japenese or Chinese what should I DO? I am scared as hell bro
ITS DOING SOME WEIRD STUFF NOW- GPS, SIM etc I have no clue .-.
UPDATE: Rebooting phone- Back to my home screen now. Heres what happened
(uploading video will post link here soon)

manandua01 said:
I installed TWRP unlocked bootloader copied SuperSU- and was abt to root. With volume up and down I came to Factory Mode
It said Factory Mode
I pressed on power button- now it shows something in Japenese or Chinese what should I DO? I am scared as hell bro
ITS DOING SOME WEIRD STUFF NOW- GPS, SIM etc I have no clue .-.
UPDATE: Rebooting phone- Back to my home screen now. Heres what happened
(uploading video will post link here soon)
Click to expand...
Click to collapse
As i have mentioned in my thread that you need to select recovery mode and not factory mode
Please select recovery mode and you should b able to see twrp
Note - to select recovery mode press volum up n down button till it shows 'recovery mode ' in the andrioid logo screen

akash.mahadeshwar said:
1 - It is the Image file which is specifically build for S356 (build number) hence it is necessary to flash it before flashing TWRP. If you don't flash boot image then you might face boot loop issues and hard brick your phone.
2 - The correct command is 'fastboot flash boot boot_XT1663_356.img' . the first boot is to recognize cmd that we are flashing a boot image and the second boot is the name of image file.
3 - Flashing TWRP and Super SU won't erase your data.
Click to expand...
Click to collapse
akash.mahadeshwar said:
As i have mentioned in my thread that you need to select recovery mode and not factory mode
Please select recovery mode and you should b able to see twrp
Note - to select recovery mode press volum up n down button till it shows 'recovery mode ' in the andrioid logo screen
Click to expand...
Click to collapse
Bro, I opened Recovery Mode, but now its asking for a password. It shows temp on the top. You from India, ryt? Could you give me your number? or maybe a skype id?
EDIT: Here's what was on my cmd after flashing the recovery http://prntscr.com/ft3t1l

manandua01 said:
Bro, I opened Recovery Mode, but now its asking for a password. It shows temp on the top. You from India, ryt? Could you give me your number? or maybe a skype id?
Click to expand...
Click to collapse
Go ahead ignore the password part.. it will only appear first time.. you should have a option to go ahead..

akash.mahadeshwar said:
As i have mentioned in my thread that you need to select recovery mode and not factory mode
Please select recovery mode and you should b able to see twrp
Note - to select recovery mode press volum up n down button till it shows 'recovery mode ' in the andrioid logo screen
Click to expand...
Click to collapse
Please reply asap
---------- Post added at 08:57 AM ---------- Previous post was at 08:56 AM ----------
akash.mahadeshwar said:
Go ahead ignore the password part.. it will only appear first time.. you should have a option to go ahead..
Click to expand...
Click to collapse
Ok trying now
---------- Post added at 09:21 AM ---------- Previous post was at 08:57 AM ----------
akash.mahadeshwar said:
Go ahead ignore the password part.. it will only appear first time.. you should have a option to go ahead..
Click to expand...
Click to collapse
Yo bro, I can only view External (sd card) storage. Not internal storage! What to do now? As I have SuperSU in Internal Storage
---------- Post added at 09:29 AM ---------- Previous post was at 09:21 AM ----------
Ok, I have rooted the phone successfully. Had to copy the SuperSU file to SD Card though 6-6

manandua01 said:
Please reply asap
---------- Post added at 08:57 AM ---------- Previous post was at 08:56 AM ----------
Ok trying now
---------- Post added at 09:21 AM ---------- Previous post was at 08:57 AM ----------
Yo bro, I can only view External (sd card) storage. Not internal storage! What to do now? As I have SuperSU in Internal Storage
---------- Post added at 09:29 AM ---------- Previous post was at 09:21 AM ----------
Ok, I have rooted the phone successfully. Had to copy the SuperSU file to SD Card though 6-6
Click to expand...
Click to collapse
Ext_sdcard folder is ur memory card folder and sdcard folder is the internal memory folder in twrp

BAM!
---------- Post added at 01:14 PM ---------- Previous post was at 01:12 PM ----------

I really thank you for this great effort
all things went good but I had a problem that I didn't find the SuperSU-v2.82-201705271822.zip although I am sure that I put it in the internal memory
please help

Hi there,
After I unlocked the bootloader, pushed the twrp recovery successfully, got stuck in the recovery mod each time I reboot the phone so can't boot the stock rom. Done wipe factory reset and format data and still nothing changed. Any ideas?
Thanks in advance OP
Edit: Just solved issue by flashing stock firmware

pdf5 said:
Hi there,
After I unlocked the bootloader, pushed the twrp recovery successfully, got stuck in the recovery mod each time I reboot the phone so can't boot the stock rom. Done wipe factory reset and format data and still nothing changed. Any ideas?
Thanks in advance OP
Edit: Just solved issue by flashing stock firmware
Click to expand...
Click to collapse
May I have the firmware file, just in case? Is it ok if firmware country code doesn't match? Do you get imei?

any idea? when image for new build will be released?

rajesh280392 said:
any idea? when image for new build will be released?
Click to expand...
Click to collapse
Well, yes ... The new boot.img for removing encryption. Especially for post-OTA updating to XT1663_S364_170803_ROW.
boot_XT1663_364.img

Does anyone know how to keep your Moto M rooted even after updating to the new security update of 7.0? Do we just flash the new .img file or what? Kinda newb here

Unlocked bootloader

Hey guys, I used the rootles tool for gcam and it got stuck at locking bootloader. Now my phone has camera 2api enabled but the bootloader is unlocked. How do I lock it.

mb145 said:
Hey guys, I used the rootles tool for gcam and it got stuck at locking bootloader. Now my phone has camera 2api enabled but the bootloader is unlocked. How do I lock it.
Click to expand...
Click to collapse
Boot your mi a1 in fastboot mode and then connect it to a computer. Open command and write fastboot oem lock, reboot your phone and it should be locked

Sly2031 said:
Boot your mi a1 in fastboot mode and then connect it to a computer. Open command and write fastboot oem lock, reboot your phone and it should be locked
Click to expand...
Click to collapse
I read some guides that say you need fastboot and adb. How do you get them. Also to boot in fastboot you need to hold power+volume down or something else?
Thank you for all the answers.

Check If camera 2 API Enabled or Not By downloading Manual Camera From Playstore .
If All Right Mean Camera 2 API Enabled .
If Camera 2 API Not present.
Just Remove Your ADB Fastboot Driver And Download latest Version Adb And Install It Manually.
Then install Camera 2 API With Gcame .
It will Lock Your Bootloader Without Any Issue

mb145 said:
I read some guides that say you need fastboot and adb. How do you get them. Also to boot in fastboot you need to hold power+volume down or something else?
Thank you for all the answers.
Click to expand...
Click to collapse
Sorry for taking so long to reply :s
Yeah, to boot in fastboot mode you have to hold power+volume down/up(depends which device u have)
After that os juts follow the steps I said before
---------- Post added at 12:51 AM ---------- Previous post was at 12:49 AM ----------
Sly2031 said:
Sorry for taking so long to reply :s
Yeah, to boot in fastboot mode you have to hold power+volume down/up(depends which device u have)
After that os juts follow the steps I said before
Click to expand...
Click to collapse
I need the latest adb drivers/usb drivers, u can download it from typing on Google, don't stress about that
After u download it, open command line and write "adb devices" if ur device show up follow the steps, if not, say something

Hi,
Someone could say me if fastboot oem off-mode-charge 0 (for power on the phone when it off and charger plug) work on this phone. I want to buy it but I need to know that before.
If someone can test it to help me, the reverse command is fastboot oem off-mode-charge 1 (and the phone charge without boot again).

Z17S (NX595J) Unlock Bootloader & TWRP

Hi, I'm new to this phone. Just got it 1 week ago. I tried to find any related information on the bootloader unlock and custom recovery, but it is very limited. I think maybe this phone is not well known. I would appreciate if someone can provide me the way to unlock bootloader, flash TWRP and roots. I can't live without magisk and viper4android. Thanks.

Here ya go,
1. Download and install minimal fastboot adb
2.Download TWRP rename it Recovery and move it to minimal fastboot adb folder
3. Unlock bootloader, in fastboot enter the following code : fastboot oem nubia_unlock NUBIA_NX595J
4. then also in fastboot: fastboot flash recovery recovery.img
5. you may need to format data in TWRP to get it to boot up !
Enjoy your new life !

thanks

dantonuci said:
Here ya go,
1. Download and install minimal fastboot adb
2.Download TWRP rename it Recovery and move it to minimal fastboot adb folder
3. Unlock bootloader, in fastboot enter the following code : fastboot oem nubia_unlock NUBIA_NX595J
4. then also in fastboot: fastboot flash recovery recovery.img
5. you may need to format data in TWRP to get it to boot up !
Enjoy your new life !
Click to expand...
Click to collapse
Hi, I've tried numerous timed and it always won't pick up the command of unlocking bootloader. It always stay in the fastboot menu. I've toggled the 'OEM Unlock' function in the developer setting, as well as the USB debugging. Any idea why the device won't pick up that command?

Is it changing to unlock after you enter the command?
If so flash twrp then boot into recovery ...

dantonuci said:
Is it changing to unlock after you enter the command?
If so flash twrp then boot into recovery ...
Click to expand...
Click to collapse
Nope. It doesn't respond to the command in the fastboot. It just shows the fastboot menu. My adb is written 'waiting for device.... '.

Drivers , uninstall all other drivers and try please

dantonuci said:
Drivers , uninstall all other drivers and try please
Click to expand...
Click to collapse
Okay will try again

storytellerz said:
Okay will try again
Click to expand...
Click to collapse
I am also finding this message, what is its solution ???

the same recovery
dantonuci said:
Here ya go,
1. Download and install minimal fastboot adb
2.Download TWRP rename it Recovery and move it to minimal fastboot adb folder
3. Unlock bootloader, in fastboot enter the following code : fastboot oem nubia_unlock NUBIA_NX595J
4. then also in fastboot: fastboot flash recovery recovery.img
5. you may need to format data in TWRP to get it to boot up !
Enjoy your new life !
Click to expand...
Click to collapse
Hi there, when I flashed the recovery that is always the stock recovery, why?

vins84 said:
Hi there, when I flashed the recovery that is always the stock recovery, why?
Click to expand...
Click to collapse
Not sure what you're asking, did you want to flash TWRP or stock? I was just giving tutorial for how to install TWRP

dantonuci said:
Here ya go,
1. Download and install minimal fastboot adb
2.Download TWRP rename it Recovery and move it to minimal fastboot adb folder
3. Unlock bootloader, in fastboot enter the following code : fastboot oem nubia_unlock NUBIA_NX595J
4. then also in fastboot: fastboot flash recovery recovery.img
5. you may need to format data in TWRP to get it to boot up !
Enjoy your new life !
Click to expand...
Click to collapse
I'm having the problem. Unlock is not sticking to unlock. The unlock works and the flash works but as soon as you try and reboot into recovery it hangs at a blank screen no twrp. Console says waiting for device and stuck. next time I go into bootloader it says locked. The count is 3 for unlock count is there a limit? 7-6-18 Nubia Z17 NX591J WIn 10.

bmaz121 said:
I'm having the problem. Unlock is not sticking to unlock. The unlock works and the flash works but as soon as you try and reboot into recovery it hangs at a blank screen no twrp. Console says waiting for device and stuck. next time I go into bootloader it says locked. The count is 3 for unlock count is there a limit? 7-6-18 Nubia Z17 NX591J WIn 10.
Click to expand...
Click to collapse
Trouble shoot and experiment with the process it will work, even if it appears not locked after reboot

dantonuci said:
Trouble shoot and experiment with the process it will work, even if it appears not locked after reboot
Click to expand...
Click to collapse
I don't understand? Appears not locked? It is locked. Now I remember when I flashed my Star N997 the developer said that there is a unlock bit that has to be turned on in the process of unlocking. I think this may be the case here since it unlocks until a reboot. I am deep concerned that after a unlock count of 3 the phone will not boot anymore. Do you know anything about these things? Another thought is does the USB C need different drivers and should it be plugged into a USB 3.0 outlet?

TWRP will flash only when it's unlocked so even if it's saying it's locked go by what you can do with TWRP
---------- Post added at 12:25 AM ---------- Previous post was at 12:24 AM ----------
I did it several times and never had a problem

i was looking for camera.apk file from Nubia Z17S phone from Stock ROM, can anyone upload it here..it should be located in system / app or app-pvt folder, you can copy using Root Explorer tool.
pls. let me know...

I'm having problems unlocking the bootloader. Has anyone got the proper TWRP for this phone? I can't find it. The one I have says FAILED (remote: Requested download size is more than max allowed). Thanks

hello links no longer works. Someone could give me back the TWRP and minimalb fastboot adb

For anyone's information, TWRP will not boot in recovery while the phone is being charged. Unplug first. You will just get a black screen.

i am also experiencing the same issue.. where can i find the drivers for this phone nx595j? or how do i uninstall the drivers for it?
---------- Post added at 01:21 AM ---------- Previous post was at 01:17 AM ----------
yo can somebody help me install a custom rom on my z17s via team viewer?? im willing to pay for your time