Related
This is really weird. I am not sure what to do at this point. Here is the rundown on what happened:
I used the phone today, made phone calls, everything was fine. It was just sitting on my desk and then I got a call so I went to go answer it. When I tried to press answer, nothing happened. None of my other buttons would work either. I powered the phone off and rebooted it. It booted to the recovery image and is still stuck there.
I was running RC29 1.0 just followed the tutorial here http://forum.xda-developers.com/showthread.php?t=442480 to root it when I first got it and stopped installing the SPL. I had been thinking about upgrading to JF1.51 anyway so I thought this would be a good opportunity to force me to do it. I downloaded the new radio and the ROM. I installed both and the updates said they completed correctly. It still boots to the recovery image every time I turn it on.
For some more info, the phone will not reboot by pressing Home+Back like the recovery image says it should, I have to pull the battery to get it to turn off. Also, I can use adb to run commands on the phone.
Does anyone have any advice on where to go from here?? I've done a crap-ton of searching on here and across the internet and haven't been able to find much. If you need any more information on the situation please let me know. I would REALLY appreciate the help.
Your phone isn't bricked, so don't worry. Start over fresh from rooting, installing the DREAMIMG.nbh and the SPL. Follow the instruction carefully, and remember, Nandroid is your friend, so use it often.
Thanks for the look. I tried to do the process over again but holding down the camera button while powering on the phone will not bring me to the bootloader menu. It boots into the recovery utility every time.
Any other suggestions?
I still can't get anywhere with it? Does anyone have an idea on how I can get it into the bootloader?
Sorry for the huge post, but here is the dmesg output:
Code:
/ # dmesg
dmesg
[ 0.000000] Linux version 2.6.25-01843-gfea26b0 ([email protected]) (gc
c version 4.2.1) #5 PREEMPT Sun Nov 16 03:48:59 UTC 2008
[ 0.000000] CPU: ARMv6-compatible processor [4117b362] revision 2 (ARMv6TEJ),
cr=00c5387f
[ 0.000000] Machine: trout
[ 0.000000] AKM Data size = 1018 , 0x89768976, size = 4064
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 25856
[ 0.000000] DMA zone: 202 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 25654 pages, LIFO batch:7
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] trout_init_map_io()
[ 0.000000] clock_init()
[ 0.000000] ACPU running at 384000 KHz
[ 0.000000] WARNING - Bad VDD (0 != 3) for this freq
[ 0.000000] CPU0: D VIPT write-back cache
[ 0.000000] CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 s
ets
[ 0.000000] CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 s
ets
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag
es: 25654
[ 0.000000] Kernel command line: board_trout.disable_uart3=0 board_trout.usb_
h2w_sw=0 board_trout.disable_sdcard=0 board_trout.smisize=64 androidboot.baseba
nd=1.22.12.29 androidboot.bootloader=0.95.3000 androidboot.carrier=TMUS board_tr
out.keycaps=qwerty androidboot.mode=recovery androidboot.serialno=HT842GZ02076
[ 0.000000] Unknown boot option `board_trout.smisize=64': ignoring
[ 0.000000] Unknown boot option `androidboot.baseband=1.22.12.29': ignoring
[ 0.000000] Unknown boot option `androidboot.bootloader=0.95.3000': ignoring
[ 0.000000] Unknown boot option `androidboot.carrier=TMUS': ignoring
[ 0.000000] Unknown boot option `androidboot.mode=recovery': ignoring
[ 0.000000] trout_init_irq()
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.010000] Memory: 101MB = 101MB total
[ 0.010000] Memory: 97536KB available (2608K code, 760K data, 100K init)
[ 0.010000] Calibrating delay loop... 383.38 BogoMIPS (lpj=1916928)
[ 0.230000] Mount-cache hash table entries: 512
[ 0.230000] CPU: Testing write buffer coherency: ok
[ 0.230000] net_namespace: 440 bytes
[ 0.230000] NET: Registered protocol family 16
[ 0.230000] trout_init() revision=128
[ 0.240000] trout_init: cpld_usb_hw2_sw = 0
[ 0.240000] trout_gpio_irq_handler: got masked interrupt: 0:84
[ 0.340000] msm_i2c_probe
[ 0.340000] msm_i2c_probe: clk_ctl 35d, 100000 Hz
[ 0.380000] Bluetooth: Core ver 2.11
[ 0.380000] NET: Registered protocol family 31
[ 0.380000] Bluetooth: HCI device and connection manager initialized
[ 0.380000] Bluetooth: HCI socket layer initialized
[ 0.380000] NET: Registered protocol family 2
[ 0.390091] Switched to high resolution mode on CPU 0
[ 0.470671] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.472838] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.473326] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.473601] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.473662] TCP reno registered
[ 0.501586] Unpacking initramfs... done
[ 1.052929] Freeing initrd memory: 1305K
[ 1.055554] Registered led device: lcd-backlight
[ 1.056195] smd_init()
[ 1.056286] smd_core_init()
[ 1.056530] smd_alloc_channel() 'SMD_RPCCALL' cid=2, shared=e010d9a0
[ 1.056927] smd_alloc_channel() 'SMD_DATA5' cid=11, shared=e0119a18
[ 1.057263] smd_alloc_channel() 'SMD_DATA6' cid=12, shared=e011da40
[ 1.057568] smd_alloc_channel() 'SMD_DATA7' cid=13, shared=e0121a68
[ 1.057873] smd_alloc_channel() 'SMD_DATA11' cid=17, shared=e01119c8
[ 1.058178] smd_alloc_channel() 'SMD_GPSNMEA' cid=27, shared=e0131b08
[ 1.058483] smd_alloc_channel() 'SMD_CS_A2M' cid=33, shared=e01159f0
[ 1.058758] smd_alloc_channel() 'SMD_DATA5_CNTL' cid=38, shared=e0125a90
[ 1.059063] smd_alloc_channel() 'SMD_DATA6_CNTL' cid=39, shared=e0129ab8
[ 1.059338] smd_alloc_channel() 'SMD_DATA7_CNTL' cid=40, shared=e012dae0
[ 1.059674] smd_core_init() done
[ 1.062441] SMD: ch 2 OPENING -> OPENED
[ 1.064241] hw3d: 0 init
[ 1.064760] msm_perf_init():
[ 1.066469] H2W: Registering H2W (headset) driver
[ 1.069033] input: h2w headset as /class/input/input0
[ 1.082502] RPC_TIME_TOD_SET_APPS_BASES:
[ 1.082532] tick = 343159
[ 1.082532] stamp = 3858764230
[ 1.084577] ashmem: initialized
[ 1.086134] yaffs Nov 16 2008 03:47:51 Installing.
[ 1.086317] io scheduler noop registered
[ 1.086408] io scheduler anticipatory registered (default)
[ 1.087324] logger: created 64K log 'log_main'
[ 1.087598] logger: created 256K log 'log_events'
[ 1.087873] logger: created 64K log 'log_radio'
[ 1.088087] ram_console: got buffer at 16d00000, size 20000
[ 1.088697] ram_console: uncorrectable error in header
[ 1.088880] ram_console: no valid data in buffer (sig = 0xffffffff)
[ 1.088941] console [ram-1] enabled
[ 1.091739] pmem: 1 init
[ 1.092807] pmem_adsp: 0 init
[ 1.094028] pmem_gpu0: 0 init
[ 1.095676] pmem_gpu1: 0 init
[ 1.100915] pmem_camera: 0 init
[ 1.102777] mddi_pmdh: init() base=0xe000b000 irq=16
[ 1.109307] get_smem_clock: state 10429 clock 0
[ 1.130000] smd_alloc_channel() 'SMD_DS' cid=0, shared=e0135b38
[ 1.130457] smd_alloc_channel() cid 7 does not exist
[ 1.131373] smd_alloc_channel() 'SMD_DATA2' cid=8, shared=e013db88
[ 1.132258] smd_alloc_channel() 'SMD_DATA3' cid=9, shared=e0141bb0
[ 1.133356] smd_alloc_channel() 'SMD_DATA4' cid=10, shared=e0145bd8
[ 1.140305] mddi cmd send rtd: int 3a000, stat 8063, rtd val d
[ 1.160793] mddi_pmdh: publish: mddi_c_d263_0000
[ 1.162960] vsync on gpio 97 now 0
[ 1.163601] mddi_pmdh: mddi_add_panel(c035f5e0, c02c2660)
[ 1.163967] mddi_pmdh: publish: mddi_panel
[ 1.164974] msmfb_probe() installing 320 x 480 panel
[ 1.200976] msm_serial: detected port #0
[ 1.201586] msm_serial.0: ttyMSM0 at MMIO 0xa9a00000 (irq = 9) is a MSM
[ 1.203051] msm_serial: driver initialized
[ 1.205340] loop: module loaded
[ 1.206011] PPP generic driver version 2.4.2
[ 1.206622] PPP Deflate Compression module registered
[ 1.207019] PPP BSD Compression module registered
[ 1.217568] allocated dma buffer at ffc01000, dma_addr 163db000
[ 1.218178] read CFG0 = aad400c0, CFG1 = 4745c
[ 1.218789] CFG0 = e8d408c0, CFG1 = 4745c
[ 1.219124] CFG0: cw/page=3 ud_sz=516 ecc_sz=10 spare_sz=1 num_addr_cycles=5
[ 1.219765] NAND_READ_ID = 1500aaec
[ 1.220152] status: c03120
[ 1.220518] nandid: 1500aaec maker ec device aa
[ 1.221129] CFG0: cw/page=3 ud_sz=512 ecc_sz=10 spare_sz=5
[ 1.221525] DEV_CMD1: f00f3000
[ 1.221861] NAND_EBI2_ECC_BUF_CFG: 1ff
[ 1.222441] flash_id: 1500aaec size 10000000
[ 1.222777] Creating 6 MTD partitions on "msm_nand":
[ 1.223387] 0x024c0000-0x02500000 : "misc"
[ 1.224608] 0x026c0000-0x02bc0000 : "recovery"
[ 1.225798] 0x02bc0000-0x02e40000 : "boot"
[ 1.227141] 0x02e40000-0x071c0000 : "system"
[ 1.228392] 0x071c0000-0x0b540000 : "cache"
[ 1.229643] 0x0b540000-0x10000000 : "userdata"
[ 1.231586] usb_probe() io=c6806000, irq=47, dma=ffc02000(163e5000)
[ 1.232929] usb_function_register() 'adb'
[ 1.233845] usb_function_register() 'usb_mass_storage'
[ 1.234211] msm_hsusb: functions bound. starting.
[ 1.234791] usb_bind_func() 'usb_mass_storage'
[ 1.235645] usb_mass_storage usb_mass_storage: Number of LUNs=1
[ 1.236042] usb_bind_func() 'adb'
[ 1.236622] adb_bind() c63d7874, c63d7a34
[ 1.237049] adb_bind() allocated 4 rx and 4 tx requests
[ 1.238453] usb_function_register() 'diag'
[ 1.239399] mice: PS/2 mouse device common for all mice
[ 1.240122] hsusb: IDLE -> ONLINE
[ 1.240793] hsusb: reset controller
[ 1.290122] ulpi: write 0x40 to 0x31
[ 1.290518] ulpi: write 0x1d to 0x0d
/ #
Looking at the Kernel Command Line message at the top makes it look like the phone doesn't know what any of the android.boot commands do so it defaults to recovery. Why would it be doing this?
the last post was too long to fix everything. here is the rest:
Code:
[ 1.291068] ulpi: write 0x1d to 0x10
[ 1.291403] ept #0 out max:64 head:ffc02000 bit:0
[ 1.291739] ept #1 out max:512 head:ffc02080 bit:1
[ 1.292288] ept #2 out max:512 head:ffc02100 bit:2
[ 1.292624] ept #0 in max:64 head:ffc02040 bit:16
[ 1.293204] ept #1 in max:512 head:ffc020c0 bit:17
[ 1.293540] ept #2 in max:512 head:ffc02140 bit:18
[ 1.293997] usb: notify offline
[ 1.294669] hsusb: ONLINE -> OFFLINE
[ 1.300610] msm_i2c msm_i2c.0: Error during data xfer (-5)
[ 1.311373] synaptics_ts_probe: Product Major Version 1
[ 1.313021] synaptics_ts_probe: Product Minor Version c
[ 1.314669] synaptics_ts_probe: product property 2
[ 1.316469] synaptics_ts_probe: device control 81
[ 1.318026] synaptics_ts_probe: interrupt enable 3
[ 1.320000] synaptics_ts_probe: 0xe0: 1 1 1 2 1 c 0 0
[ 1.320000] synaptics_ts_probe: max_x 3480, max_y 5368
[ 1.320000] synaptics_ts_probe: inactive_x -80 -80, inactive_y -32 -32
[ 1.320000] synaptics_ts_probe: snap_x 240-248 240-248, snap_y 80-88 80-88
[ 1.320000] input: synaptics-rmi-touchscreen as /class/input/input1
[ 1.370854] synaptics_ts_probe: Start touchscreen synaptics-rmi-touchscreen i
n interrupt mode
[ 1.371770] GPIO Event Driver
[ 1.372716] GPIO Keypad Driver: Start keypad matrix for trout-keypad-v3 in in
terrupt mode
[ 1.373692] No IRQF_TRIGGER set_type function for IRQ 191 (troutgpio)
[ 1.374364] No IRQF_TRIGGER set_type function for IRQ 192 (troutgpio)
[ 1.374852] GPIO Input Driver: Start gpio inputs for trout-keypad-v3 in inter
rupt mode
[ 1.375584] No IRQF_TRIGGER set_type function for IRQ 188 (troutgpio)
[ 1.376103] GPIO Input Driver: Start gpio inputs for trout-keypad-v3 in inter
rupt mode
[ 1.377476] input: trout-keypad-v3 as /class/input/input2
[ 1.430946] No IRQF_TRIGGER set_type function for IRQ 186 (troutgpio)
[ 1.431434] GPIO Input Driver: Start gpio inputs for trout-nav in interrupt m
ode
[ 1.432716] input: trout-nav as /class/input/input3
[ 1.491831] rs30000048:0da5b528 rs30000048:0da5b528: rtc core: registered msm
_rtc as rtc0
[ 1.496103] Registered led device: blue
[ 1.496897] Registered led device: green
[ 1.497782] Registered led device: red
[ 1.498361] AKM8976A compass driver: init
[ 1.498880] No IRQF_TRIGGER set_type function for IRQ 187 (troutgpio)
[ 1.500000] input: compass as /class/input/input4
[ 1.531129] pdev->dev.platform_data is not NULL
[ 1.531861] mt9t013: probe
[ 1.532197] mt9t013: init
[ 1.532502] mt9t013: mt9t013_register_init
[ 1.533082] mt9t013: camera sensor_reset set as 1
[ 1.535432] mt9t013: clk_get(vfe_mdc_clk): c02b2cd4
[ 1.535828] mt9t013: clk_get(mdc_clk): c02b2954
[ 1.536439] mt9t013: clk select 1
[ 1.536744] mt9t013: clk_get(vfe_clk): c02b2cb4
[ 1.537385] mt9t013: enable vfe_clk
[ 1.560091] mt9t013: clk select 0
[ 1.569277] mt9t013: camera sensor init sequence done
[ 1.569857] mt9t013: camera sensor suspend sequence
[ 1.570091] mt9t013: disabling vfe_clk
[ 1.570457] mt9t013: clk_put(vfe_clk): c02b2cb4
[ 1.571281] mt9t013: camera sensor suspend sequence done
[ 1.572258] Bluetooth: HCI UART driver ver 2.2
[ 1.572899] Bluetooth: HCI H4 protocol initialized
[ 1.573204] Bluetooth: HCILL protocol initialized
[ 1.574577] mmc0: Qualcomm MSM SDCC at 0x00000000e1000000 irq 24,0 dma -1
[ 1.575218] mmc0: 4 bit data mode enabled
[ 1.575554] mmc0: MMC clock 144000 -> 20000000 Hz, PCLK 64000000 Hz
[ 1.576134] mmc0: Slot eject status = 1
[ 1.576439] mmc0: Power save feature enable = 0
[ 1.577019] mmc0: PIO transfer enabled
[ 1.578392] mmc1: Qualcomm MSM SDCC at 0x00000000e1001000 irq 26,194 dma 8
[ 1.579002] mmc1: 4 bit data mode enabled
[ 1.579369] mmc1: MMC clock 144000 -> 20000000 Hz, PCLK 64000000 Hz
[ 1.580061] mmc1: Slot eject status = 0
[ 1.580396] mmc1: Power save feature enable = 0
[ 1.580732] mmc1: DM non-cached buffer at ffc04000, dma_addr 0x15805000
[ 1.581312] mmc1: DM cmd busaddr 360730624, cmdptr busaddr 360731392
[ 1.582472] Registered led device: spotlight
[ 1.583326] Registered led device: keyboard-backlight
[ 1.583967] Registered led device: button-backlight
[ 1.585188] No IRQF_TRIGGER set_type function for IRQ 190 (troutgpio)
[ 1.586683] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 1.595432] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.596103] TCP cubic registered
[ 1.596622] NET: Registered protocol family 1
[ 1.597415] NET: Registered protocol family 17
[ 1.597843] Bluetooth: L2CAP ver 2.9
[ 1.598422] Bluetooth: L2CAP socket layer initialized
[ 1.598789] Bluetooth: SCO (Voice Link) ver 0.6
[ 1.599124] Bluetooth: SCO socket layer initialized
[ 1.600274] Bluetooth: RFCOMM socket layer initialized
[ 1.600732] Bluetooth: RFCOMM TTY layer initialized
[ 1.601312] Bluetooth: RFCOMM ver 1.9
[ 1.602105] clock_late_init() disabled 20 unused clocks
[ 1.604547] rs30000048:0da5b528 rs30000048:0da5b528: setting system clock to
2009-06-22 14:22:20 UTC (1245680540)
[ 1.605127] Freeing init memory: 100K
[ 1.833296] init: cannot open '/initlogo.rle'
[ 1.836988] init: Unable to open persistent property directory /data/property
errno: 2
[ 1.854486] enabling adb function
[ 1.857080] init: cannot find '/system/bin/akmd', disabling 'akmd'
[ 2.151251] init sharp panel
[ 2.205005] yaffs: dev is 32505860 name is "mtdblock4"
[ 2.205401] yaffs: passed flags ""
[ 2.205981] yaffs: Attempting MTD mount on 31.4, "mtdblock4"
[ 2.210763] yaffs: restored from checkpoint
[ 2.211404] yaffs_read_super: isCheckpointed 1
[ 2.568758] mmc_sd_init_card: Delay 250 ms
[ 2.682685] save exit: isCheckpointed 1
[ 2.910061] mmc1: host does not support reading read-only switch. assuming wr
ite-enable.
[ 2.910427] mmc1: new SD card at address b368
[ 2.912197] mmcblk0: mmc1:b368 SD01G 999936KiB
[ 2.912960] mmcblk0: p1
[ 3.040006] hsusb: OFFLINE -> ONLINE
[ 3.040006] hsusb: reset controller
[ 3.070128] ulpi: write 0x40 to 0x31
[ 3.070433] ulpi: write 0x1d to 0x0d
[ 3.070983] ulpi: write 0x1d to 0x10
[ 3.071288] ept #0 out max:64 head:ffc02000 bit:0
[ 3.071563] ept #1 out max:512 head:ffc02080 bit:1
[ 3.072112] ept #2 out max:512 head:ffc02100 bit:2
[ 3.072417] ept #0 in max:64 head:ffc02040 bit:16
[ 3.072936] ept #1 in max:512 head:ffc020c0 bit:17
[ 3.073241] ept #2 in max:512 head:ffc02140 bit:18
[ 3.073638] usb: notify offline
[ 3.078856] usb: suspend
[ 3.130006] usb: reset
[ 3.130006] usb: portchange
[ 3.130006] usb: reset
[ 3.130006] usb: portchange
[ 3.140006] usb_mass_storage usb_mass_storage: config #1
[ 7.352186] init: untracked pid 44 exited
[ 14.633174] init: untracked pid 57 exited
/ #
I didnt look through the dmesg out put but it sounds like your home key is stuck down.
Thats what I thought at first too but I still had full range of motion of the button when clicking it.
Anyway, I switched my SIM out to an older phone so I at least had something to use. Got back home and decided to try booting the phone without a SIM, booted to the setup screen. Powered off and put the SIM back in and it started up fine. Not positive that the SIM removal fixed it but its working! w00t!
can you describe the screen that it boots too? is it black with yellow text, grey backgound, rainbow, etc...
mm0
Now that it is working I would recommend to restart the whole process of Rooting and flashing your rom so that nothing is messed up.
Crap, its doing it again. I am pretty dang sure that the Home button is not stuck down, it clicks like normal, like it always has.
It boots up into the recovery screen, no matter if I try to boot into Bootloader mode (holding the camera button down) or not. It is the screen with the ! in the triangle and the picture of the phone. I have normal control while inside of it, can wipe and update, but I cannot restart by pressing Home+Back.
Is maybe the circuitry the handles the buttons bad? I really hope not, but does anyone have any other advice?
shameful bump.... I have tried everything I know how to do and I am really at a loss.
How good are you at taking things apart?
Is the phone under warranty or did you buy it used? If Its from tmobile then id call them up and explain what its doing. Run through everything they tell you to try and Im sure they will send out a replacement.
If its not under warranty then Id try taking it apart to see if the home button contacts are stuck.
I'm not too bad at it, just really paranoid of screwing something up. Ive taken apart my Tytn2 successfully before to change a digitzer. I bought the G1 used on eBay so I have no warranty whatsoever.
I'm almost convinced now it is the button, though. It started working again. My goal is to be just to not let the battery run dead .
I've read a considerable number of threads both here and elsewhere, i'm having a ton of trouble getting HeRET.exe to work. i've formatted my sdcard with fat32, and my directory layout looks like this
Code:
[[email protected] 1BCE-6D05]$ ls * -R
VOGUIMG.nbh
andboot:
androidinstall.tgz default.txt initrd.gz
default-kaiser.txt dmesg README-BASEFILES.txt
default-polaris.txt haret.exe zImage
upon running HeRET.exe, i hold the center button on the dpad down. **** scrolls by and stops with these last few lines:
Code:
sh: 2: unkonwn operand
losetup: /dev/block/loop1: no such file or directory
failed
failed to reach system.img on SD Card
i've googled a ton for those error strings and i cant find a solution anywhere.
what am i doing wrong?
Try volume up instead of dpad center. Wait to press until the text starts scrolling.
Sent from my Full Android on Vogue using XDA App
no love. same thing. tried it 4 times in a row with the same results.
Hmm. Does the message saying "press volup / road center" show? Maybe you're getting stuck before that.
Also, there should be some logs in /sdcard/andboot, post 'em.
Sent from my Full Android on Vogue using XDA App
Yeah i do get past the 'hold volume up or center dpad' text.
here's my dmesg
Code:
[ 0.000000] Linux version 2.6.25-01130-g99a3b07-dirty ([email protected]) (gcc version 4.4.0 (GCC) ) #383 PREEMPT Tue Jul 27 15:38:06 CEST 2010
[ 0.000000] CPU: ARMv6-compatible processor [4107b364] revision 4 (ARMv6TEJ), cr=00c5387f
[ 0.000000] Machine: HTC Vogue
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 29440
[ 0.000000] DMA zone: 230 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 29210 pages, LIFO batch:7
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] clock 3fbb5 -> 3f42f
[ 0.000000] clock f8fa0b60 -> f8fa0b60
[ 0.000000] clock 1 -> 1
[ 0.000000] clock 20001 -> 20001
[ 0.000000] clocks was 2017fea7
[ 0.000000] CPU0: D VIPT write-back cache
[ 0.000000] CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
[ 0.000000] CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 29210
[ 0.000000] Kernel command line: ppp.nostart=0 mddi.width=240 mddi.height=320 msm_sdcc.msmsdcc_fmax=32000000 pm.sleep_mode=0 no_console_suspend hw3d.version=1
[ 0.000000] Unknown boot option `ppp.nostart=0': ignoring
[ 0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)
[ 0.000000] Console: colour dummy device 80x30
[ 0.000045] console [tty0] enabled
[ 0.001011] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.001691] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.010056] Unexpected Timer interrupt
[ 0.015330] Memory: 115MB = 115MB total
[ 0.015418] Memory: 111232KB available (2772K code, 1270K data, 124K init)
[ 0.016858] Calibrating delay loop... 383.38 BogoMIPS (lpj=1916928)
[ 0.230765] Mount-cache hash table entries: 512
[ 0.232211] CPU: Testing write buffer coherency: ok
[ 0.235256] net_namespace: 440 bytes
[ 0.237626] NET: Registered protocol family 16
[ 0.238403] htcvogue_init
[ 0.238501] cpld[0]=fffffc68
[ 0.238556] cpld[1]=fffffc12
[ 0.238603] cpld[2]=fffffc22
[ 0.238651] cpld[3]=fffffc00
[ 0.238698] cpld[4]=fffffccc
[ 0.238745] cpld[5]=fffffcf4
[ 0.238790] cpld[6]=fffffffb
[ 0.238838] cpld[7]=fffffc00
[ 0.239386] set gpio 19 wakeup 40000000
[ 0.239795] GPIO OEs: 0 800 0 1001 1a0
[ 0.693441] set gpio 29 wakeup 40000000
[ 0.700986] msm_i2c_probe
[ 0.701145] msm_i2c_probe: clk_ctl 35d, 100000 Hz
[ 0.730251] Bluetooth: Core ver 2.11
[ 0.731390] NET: Registered protocol family 31
[ 0.731506] Bluetooth: HCI device and connection manager initialized
[ 0.731595] Bluetooth: HCI socket layer initialized
[ 0.734465] NET: Registered protocol family 2
[ 0.740091] Switched to high resolution mode on CPU 0
[ 0.820726] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.822870] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.823283] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.823505] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.823586] TCP reno registered
[ 0.851563] Unpacking initramfs... done
[ 1.362126] Freeing initrd memory: 1199K
[ 1.363895] Registered led device: lcd-backlight
[ 1.364236] Registered led device: button-backlight
[ 1.364501] Registered led device: keyboard-backlight
[ 1.364796] Registered led device: red
[ 1.365041] Registered led device: blue
[ 1.365278] Registered led device: green
[ 1.370883] Vogue Keyboard Driver
[ 1.371931] input: qwerty as /devices/virtual/input/input0
[ 1.372871] titan ts_init
[ 1.373408] Modem Status:
[ 1.420066] USB Disconnected
[ 1.420218] msm_hsusb_set_vbus_state(0)
[ 1.431488] Initialise htc_rfkill for Bluetooth
[ 1.431633] Bluetooth 0
[ 1.449371] clk_get grp_clk
[ 1.449518] clk_get imem_clk
[ 1.451458] clk_get acpu_clk
[ 1.454478] ashmem: initialized
[ 1.455936] squashfs: version 3.4 (2008/08/26) Phillip Lougher
[ 1.456718] io scheduler noop registered (default)
[ 1.456825] io scheduler deadline registered
[ 1.457698] logger: created 64K log 'log_main'
[ 1.457998] logger: created 256K log 'log_events'
[ 1.458255] logger: created 64K log 'log_radio'
[ 1.458440] ram_console: got buffer at e0000, size 20000
[ 1.458620] ram_console: no valid data in buffer (sig = 0xffffffff)
[ 1.458795] console [ram-1] enabled
[ 1.460476] pmem: 1 init
[ 1.461373] pmem_gpu0: 0 init
[ 1.462630] pmem_gpu1: 0 init
[ 1.463596] pmem_camera: 1 init
[ 1.464688] pmem_adsp: 0 init
[ 1.465936] clk_get mdp_clk
[ 1.466573] mddi_pmdh: init() base=0xe000b000 irq=16
[ 1.466686] clk_get pmdh_clk
[ 1.474460] mddi0_client_power(1)
[ 1.474746] mddi_pmdh: unsupported version 0x19
[ 1.474928] mddi cmd send rtd: int 23a000, stat 808063, rtd val e
[ 1.475235] mddi_pmdh: publish: mddi_c_0000_0000
[ 1.476220] vsync on gpio 97 now 0
[ 1.476341] mddi_pmdh: mddi_add_panel(c040ea90, c0313c70)
[ 1.476421] mddi_pmdh: publish: mddi_panel
[ 1.476825] msmfb_probe() installing 240 x 320 panel
[ 1.480000] fus
[ 1.480000] fake_vsync_int for update
[ 1.480000] Panel type set to 1
[ 1.684593] mddi0_panel_power(1)
[ 1.688866] Console: switching to colour frame buffer device 40x29
[ 1.730921] msm_serial: driver initialized
[ 1.735863] clk_get uart1dm_clk
[ 1.738628] clk_set_rate 34:1843200
[ 1.740408] msm_serial_hs.0: ttyMSM0 at MMIO 0xa0200000 (irq = 45) is a MSM HS UART
[ 1.752058] loop: module loaded
[ 1.754803] PPP generic driver version 2.4.2
[ 1.760505] PPP Deflate Compression module registered
[ 1.765801] PPP BSD Compression module registered
[ 1.773131] allocated dma buffer at ffc7b000, dma_addr 164cc000
[ 1.780166] read CFG0 = aad400c0, CFG1 = 4747c
[ 1.786091] CFG0 = a8d408c0, CFG1 = 4745c
[ 1.790058] CFG0: cw/page=3 ud_sz=516 ecc_sz=10 spare_sz=1 num_addr_cycles=5
[ 1.796166] NAND_READ_ID = 1500aaec
[ 1.800206] status: c03020
[ 1.803300] nandid: 1500aaec maker ec device aa
[ 1.810110] CFG0: cw/page=3 ud_sz=512 ecc_sz=10 spare_sz=5
[ 1.816260] DEV_CMD1: f00f3000
[ 1.820065] <6>NAND_EBI2_ECC_BUF_CFG: 0
[ 1.825995] flash_id: 1500aaec size 5580ba2c10000000
[ 1.831571] usb_probe() io=c7f06000, irq=15, dma=ffc7c000(164d2000)
[ 1.840065] clk_get usb_hs_clk
[ 1.843175] clk_get usb_hs_pclk
[ 1.846610] usb_function_register() 'adb'
[ 1.850521] usb_function_register() 'usb_mass_storage'
[ 1.856143] msm_hsusb: functions bound. starting.
[ 1.860601] usb_mass_storage usb_mass_storage: Number of LUNs=1
[ 1.871041] usb_ether_setup()
[ 1.876253] usb_function_register() 'ether'
[ 1.880193] hsusb: IDLE -> ONLINE
[ 1.883113] hsusb: reset controller c64cfc00
[ 1.911308] usb: notify offline
[ 1.914245] hsusb: ONLINE -> OFFLINE
[ 1.941931] input: TSC2003 Touchscreen as /devices/virtual/input/input1
[ 1.970548] GPIO Event Driver
[ 1.973811] set gpio 31 wakeup 40000000
[ 1.979506] set gpio 32 wakeup 40000000
[ 1.980000] set gpio 33 wakeup 40000000
[ 1.980000] set gpio 35 wakeup 40000000
[ 1.980000] set gpio 34 wakeup 40000000
[ 1.980000] set gpio 21 wakeup 40000000
[ 1.980148] GPIO Input Driver: Start gpio inputs for vogue_keypad in polling mode
[ 1.990818] input: vogue_keypad as /devices/virtual/input/input2
[ 2.060601] MSM RTC init
[ 2.063903] RTC probe
[ 2.067971] msm_rtc msm_rtc.0: rtc core: registered msm_rtc as rtc0
[ 2.070761] MSM RTC started
[ 2.074205] s5k4b1fx: probe
[ 2.084956] Bluetooth: HCI UART driver ver 2.2
[ 2.090101] Bluetooth: HCI H4 protocol initialized
[ 2.095675] Bluetooth: HCILL protocol initialized
[ 2.100928] clk_get sdc1_pclk
[ 2.103890] clk_get_rate 20:66000000
[ 2.106805] clk_get sdc1_clk
[ 2.110126] clk_set_rate 19:144000
[ 2.215761] clk_get_rate 19:144000
[ 2.218910] set sdcc vdd to 0
[ 2.220340] mmc0: Qualcomm MSM SDCC at 0x00000000e1000000 irq 24,0 dma 8
[ 2.225293] mmc0: 4 bit data mode enabled
[ 2.230051] mmc0: MMC clock 144000 -> 32000000 Hz, PCLK 66000000 Hz
[ 2.235446] mmc0: Slot eject status = 0
[ 2.240040] mmc0: Power save feature enable = 1
[ 2.245461] mmc0: DM non-cached buffer at ffc7e000, dma_addr 0x164eb000
[ 2.250096] mmc0: DM cmd busaddr 0x164eb000, cmdptr busaddr 0x164eb300
[ 2.255720] mmc0: Polling status mode enabled
[ 2.260836] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[ 2.276655] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.280505] ClusterIP Version 0.8 loaded successfully
[ 2.290278] arp_tables: (C) 2002 David S. Miller
[ 2.296755] TCP cubic registered
[ 2.300388] NET: Registered protocol family 1
[ 2.306961] NET: Registered protocol family 17
[ 2.310238] Bluetooth: L2CAP ver 2.9
[ 2.313503] Bluetooth: L2CAP socket layer initialized
[ 2.320100] Bluetooth: SCO (Voice Link) ver 0.6
[ 2.330141] Bluetooth: SCO socket layer initialized
[ 2.336563] Bluetooth: RFCOMM socket layer initialized
[ 2.340230] Bluetooth: RFCOMM TTY layer initialized
[ 2.346216] Bluetooth: RFCOMM ver 1.9
[ 2.350261] Bluetooth: BNEP (Ethernet Emulation) ver 1.2
[ 2.356218] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 2.361336] msm_rtc msm_rtc.0: setting system clock to 2010-09-19 02:18:47 UTC (1284862727)
[ 2.370293] Freeing init memory: 124K
[ 2.720098] set sdcc vdd to 17
[ 2.733608] Setting SD VREG to 2950
[ 2.746028] mmc0: Command timeout
[ 2.750000] mmc0: Command timeout
[ 2.750000] mmc0: Command timeout
[ 2.750000] mmc0: Command timeout
[ 2.750000] SD Init
[ 2.754013] set sdcc vdd to 15
[ 2.756556] Setting SD VREG to 2750
[ 2.798453] mmc_sd_init_card: Delay 250 ms
[ 3.060000] clk_set_rate 19:25000000
[ 3.156216] mmc0: host does not support reading read-only switch. assuming write-enable.
[ 3.160113] SD Init Retry
[ 3.162605] mmc0: new SDHC card at address d555
[ 3.171025] mmcblk0: mmc0:d555 SU04G 3979776KiB
[ 3.176448] mmcblk0: p1
i dont see anything that sticks out though...
bump.
i've tried several different android packs and still the same issue. im really stuck. hell if someone would be willing to skype and help me figure it out i'd be willing. im just tired of being frustrated and such. i've literally ben googling for about 5 hours today trying different things.
bump again. i can provide any information needed, i'd really like to get this working. anyone? ive repeated the steps at least 7 times now and no love. any help is appreciated, even armature speculations.
[mutex] said:
I've read a considerable number of threads both here and elsewhere, i'm having a ton of trouble getting HeRET.exe to work. i've formatted my sdcard with fat32, and my directory layout looks like this
Code:
[[email protected] 1BCE-6D05]$ ls * -R
VOGUIMG.nbh
andboot:
androidinstall.tgz default.txt initrd.gz
default-kaiser.txt dmesg README-BASEFILES.txt
default-polaris.txt haret.exe zImage
upon running HeRET.exe, i hold the center button on the dpad down. **** scrolls by and stops with these last few lines:
Code:
sh: 2: unkonwn operand
losetup: /dev/block/loop1: no such file or directory
failed
failed to reach system.img on SD Card
i've googled a ton for those error strings and i cant find a solution anywhere.
what am i doing wrong?
Click to expand...
Click to collapse
Lets back up a step... which ROM are you trying to use? From SD or NAND? The message says that it cannot find the system.img, and if it is the first boot, it obviously will not find it as the system.img has not been created at this point. From what I understand, it may be something on your default.txt.
I would just download a fresh rom, (get myn's latest for now and see if the device reacts). Delete the Android folder in your SD card and replace it by myn's
Followed the instructions for myn's to a T. I'm using the NoMoRootFS method, not NAND (yet).
I checked the init code - basically, you're seeing the failure messages because
1) you aren't installed to nand
2) your sdcard doesn't have a 2nd/3rd partition
3) you don't have a system.img on your sdcard
all that basically means is, it's becuase you haven't made it into the installer - so there's not a lot to be gleaned from the failure messages and, unfortunately, there's not a lot of logging... ok, so you've tried volup, dpad center, how about touchscreen center? It should work also.
I mean, I could generate a custom init that ALWAYS enters the installer to get you through this part, or you could try generating a boot script with the bootscriptgenerator you can find in the vogue android subforum...
does the console print anything when you press buttons? what's the date on your zImage? and did you download the 2.6.25 or 2.6.32 version?
I used the SQSH method here http://download640.mediafire.com/5mvxwozyuQjg/oitjoljxquj/myn-WarmDonut-04-24-2010-SQSH.zip
works fine. not sure what i was doing wrong but oh well. well, works fine with the exception of the camera button doing back/home(hold). thats kinda iffy. seems to only work in specific contexts. i.e. inside the 'browser' or email app i cant leave to the main screen. better than no android though.
thanks for your help guys. i wonder why the NoMoRootFS method didnt work though ;/
[mutex] said:
I used the SQSH method here http://download640.mediafire.com/5mvxwozyuQjg/oitjoljxquj/myn-WarmDonut-04-24-2010-SQSH.zip
works fine. not sure what i was doing wrong but oh well. well, works fine with the exception of the camera button doing back/home(hold). thats kinda iffy. seems to only work in specific contexts. i.e. inside the 'browser' or email app i cant leave to the main screen. better than no android though.
thanks for your help guys. i wonder why the NoMoRootFS method didnt work though ;/
Click to expand...
Click to collapse
quick press = back
med press = home
long press = recent programs
if that helps...
yeah i know those, its just that sometimes the camera button doesnt do anything, quick press hold or long hold.
Hmm... well, the old sqsh method can be pretty sluggish, too, I wonder if your presses just aren't registering properly... anyway, you sound like the sort who will got to nand after some initial testing. everything is much, much better on nand.
yeah thats what im doing now. everything works fine with the exception of the camera button and like you said stuff works better. anyways, thanks for your help again.
I was trying this to fix a hard-bricked G2 I just recieved:
http://forum.xda-developers.com/showthread.php?t=2582142
The device is in the following state:
No download mode
No recovery mode
Shows qhsusb_bulk in lsusb -v
I don't know much more about it (e.g. I don't know if it was rooted or what type of ROM was on it).
I need to unplug the battery by removing the back cover to have a chance to reboot it. The first boot after that it shows the LG logo, then a blank screen (back lit but no text).
(UPDATE: Pressing the power button 8 seconds also reboots the phone without having to unplug the battery).
When I wire it up to my Arch Linux computer here is what the command `dmesg` shows:
Code:
[ 3693.728255] usb 1-2: new high-speed USB device number 93 using xhci_hcd
[ 3693.901772] usb 1-2: config 1 has an invalid interface number: 20 but max is 1
[ 3693.901784] usb 1-2: config 1 has no interface number 1
[ 3693.903319] usb-storage 1-2:1.20: USB Mass Storage device detected
[ 3693.903868] scsi host843: usb-storage 1-2:1.20
[ 3694.905067] scsi 843:0:0:0: Direct-Access Qualcomm MMC Storage 1.00 PQ: 0 ANSI: 2
[ 3694.906568] sd 843:0:0:0: [sdb] 30777344 512-byte logical blocks: (15.7 GB/14.6 GiB)
[ 3694.906872] sd 843:0:0:0: [sdb] Write Protect is off
[ 3694.906883] sd 843:0:0:0: [sdb] Mode Sense: 0f 0e 00 00
[ 3694.907373] sd 843:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3694.919101] sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 sdb11 sdb12 sdb13 sdb14 sdb15 sdb16 sdb17 sdb18 sdb19 sdb20 sdb21 sdb22 sdb23 sdb24 sdb25 sdb26 sdb27 sdb28 sdb29 sdb30 sdb31 sdb32 sdb33 sdb34 sdb35 sdb36
[ 3694.923664] sd 843:0:0:0: [sdb] Attached SCSI disk
[ 3695.061360] usb 1-2: USB disconnect, device number 93
[ 3695.065521] sd 843:0:0:0: [sdb] Synchronizing SCSI cache
[ 3695.065552] sd 843:0:0:0: [sdb]
[ 3695.065554] Result: hostbyte=0x01 driverbyte=0x00
[ 3695.065557] sd 843:0:0:0: [sdb] CDB:
[ 3695.065558] cdb[0]=0x28: 28 00
[ 3695.065562] sd 843:0:0:0: [sdb]
[ 3695.065563] Result: hostbyte=0x01 driverbyte=0x00
[ 3695.065565] sd 843:0:0:0: [sdb] CDB:
[ 3695.065566] cdb[0]=0x28:
[ 3695.065567] 00 00 00
[ 3695.065569] 28
[ 3695.065571] 00
[ 3695.065571] 00
[ 3695.065572] 00
[ 3695.065573] 01
[ 3695.065573] 70
[ 3695.065574] 00
[ 3695.065574] 00
[ 3695.065575] 90
[ 3695.065576] 00
[ 3695.065578] end_request: I/O error, dev sdb, sector 368
[ 3695.065579] 80 00 00 f0 00
[ 3695.065582] quiet_error: 134 callbacks suppressed
[ 3695.065583] Buffer I/O error on device sdb, logical block 46
[ 3695.065586] Buffer I/O error on device sdb, logical block 47
[ 3695.065587] Buffer I/O error on device sdb, logical block 48
[ 3695.065589] end_request: I/O error, dev sdb, sector 128
[ 3695.065590] Buffer I/O error on device sdb, logical block 16
[ 3695.065592] Buffer I/O error on device sdb, logical block 49
[ 3695.065594] Buffer I/O error on device sdb, logical block 17
[ 3695.065595] Buffer I/O error on device sdb, logical block 50
[ 3695.065597] Buffer I/O error on device sdb, logical block 51
[ 3695.065598] Buffer I/O error on device sdb, logical block 52
[ 3695.065599] Buffer I/O error on device sdb, logical block 18
[ 3695.065633] sd 843:0:0:0: [sdb]
[ 3695.065636] Result: hostbyte=0x01 driverbyte=0x00
[ 3695.750741] usb 1-2: new high-speed USB device number 94 using xhci_hcd
[ 3695.924146] usb 1-2: config 1 has an invalid interface number: 20 but max is 1
[ 3695.924151] usb 1-2: config 1 has no interface number 1
...
Note the "config 1 has an invalid interface number: 20 but max is 1" error, and all the Buffer I/O errors.
Here is the relevant section of `lsusb -v`
Code:
Bus 001 Device 054: ID 05c6:9006 Qualcomm, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x05c6 Qualcomm, Inc.
idProduct 0x9006
bcdDevice 0.00
iManufacturer 1 LG Electronics Inc.
iProduct 2 QHSUSB__BULK
iSerial 3 1234567890ABCDEF
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 55
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 20
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)
Is there anything that could be done to fix these Buffer I/O errors so I can mount the phone (and continue with the FIX tutorial posted above)?
Anyone able to shed some lights on the meaning of these lines would be of great help in my quest of learning how to unbrick my phone.
Note: when connected to the computer the blank screen goes in a repeating cycle of being back lit for 1 second then no backlights for 1 second. The cycle stops (with backlights) when unplugging the phone.
Hello. I've got exactly the same problem, how you already somehow solved the problem?
NECRO:
same problem on a lg device, any input is appreaciated.
will we be able to install on Nexus 10?????
ScottBroker said:
will we be able to install on Nexus 10?????
Click to expand...
Click to collapse
If there's a developer that is willing to make a build for us. There's not many devs left for the Nexus 10 but hopefully someone will work on it.
Perhaps...
jsgraphicart said:
If there's a developer that is willing to make a build for us. There's not many devs left for the Nexus 10 but hopefully someone will work on it.
Click to expand...
Click to collapse
I really hope so. Perhaps CM will come through for us.
if it hasn't happened in a month or so, bug me - i'll do it
dmitrygr said:
if it hasn't happened in a month or so, bug me - i'll do it
Click to expand...
Click to collapse
dmitrygr, alreqdy got a build without errors, but not yet booting
scanno said:
dmitrygr, alreqdy got a build without errors, but not yet booting
Click to expand...
Click to collapse
How far did you get?
Got the build to succeed but it bootloops with the Google logo.
I have no idea how I can debug this... :'(
aHcVolle said:
How far did you get?
Got the build to succeed but it bootloops with the Google logo.
I have no idea how I can debug this... :'(
Click to expand...
Click to collapse
I have the same. The bootloop is caused by the failure of selinux to load:
Code:
[ 2.951989] init: init first stage started!
[ 2.959452] SELinux: avtab: invalid type or class
[ 2.963067] init: SELinux: Could not load policy: Invalid argument
[ 2.963314] init: failed to load policy: Invalid argument
[ 2.963400] init: Security failure; rebooting into recovery mode...
[ 2.963960] SysRq : Emergency Remount R/O
[ 2.964150] Emergency Remount complete
[ 4.762034] manta_otg manta_otg_work: UNDEFINED -> b_peripheral
[ 7.174875] manta_otg manta_otg_work: b_peripheral -> b_idle
[ 7.387529] manta_bat_sync_charge_enable: charger changed enable state to 1
[ 7.393069] battery: charge source type was changed: usb
[ 7.406743] manta_otg manta_otg_work: b_idle -> b_peripheral
[ 20.751453] INFO: task init:1 blocked for more than 10 seconds.
[ 20.751594] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 20.751670] init D c066e294 0 1 0 0x00000000
scanno said:
I have the same. The bootloop is caused by the failure of selinux to load:
Code:
[ 2.951989] init: init first stage started!
[ 2.959452] SELinux: avtab: invalid type or class
[ 2.963067] init: SELinux: Could not load policy: Invalid argument
[ 2.963314] init: failed to load policy: Invalid argument
[ 2.963400] init: Security failure; rebooting into recovery mode...
[ 2.963960] SysRq : Emergency Remount R/O
[ 2.964150] Emergency Remount complete
[ 4.762034] manta_otg manta_otg_work: UNDEFINED -> b_peripheral
[ 7.174875] manta_otg manta_otg_work: b_peripheral -> b_idle
[ 7.387529] manta_bat_sync_charge_enable: charger changed enable state to 1
[ 7.393069] battery: charge source type was changed: usb
[ 7.406743] manta_otg manta_otg_work: b_idle -> b_peripheral
[ 20.751453] INFO: task init:1 blocked for more than 10 seconds.
[ 20.751594] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 20.751670] init D c066e294 0 1 0 0x00000000
Click to expand...
Click to collapse
Who did you get this log?
Sorry for this noob question
aHcVolle said:
Who did you get this log?
Sorry for this noob question
Click to expand...
Click to collapse
Boot into TWRP, adb shell, cat /proc/last_kmsg
Seems like google upgraded policydb and the kernel has an old one that is not compatible with the selinux in android 7
Thanks!
Ugh this kernel needs a lot of work. @dmitrygr guess you do not have a list of commits you used for the M bringup. That squashed commit does not help to pinpoint the selinux problems. A clean merge with the 3.4 kernel from google / linux.org is not possible with the squashed commit, after reverting it, it was almost a clean merge.
Code:
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.4.67 ([email protected]) (gcc version 4.9 20150123 (prerelease) (GCC) ) #4 SMP PREEMPT Thu Sep 8 22:17:17 CEST 2016
[ 0.000000] CPU: ARMv7 Processor [410fc0f4] revision 4 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] Machine: Manta
[ 0.000000] Initialized persistent memory from a0000000-a01fffff
[ 0.000000] ion_reserve: ion_chunk_heap reserved base 90000000 size 268435456
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] CPU EXYNOS5250 (id 0x43520210)
[ 0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[ 0.000000] clkout: bad source 0
[ 0.000000] EXYNOS5: PLL settings, A=1000000000, B=1333090909, C=333000000
[ 0.000000] M=1600000000, E=96000000, V=300000000, G=533000000
[ 0.000000] EXYNOS5: ARMCLK=1000000000, CDREX=800000000, ACLK400=533000000
[ 0.000000] ACLK333=333000000, ACLK266=266666666, ACLK200=200000000
[ 0.000000] ACLK166=166500000, ACLK66=66666666
[ 0.000000] sclk_fimd: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_g3d: source is mout_mpll_user (0), rate is 800000000
[ 0.000000] sclk_gscl_wrap0: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_gscl_wrap1: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_bayer: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_cam0: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_cam1: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_jpeg: source is ext_xtal (0), rate is 24000000
[ 0.000000] sclk_usbdrd30: source is mout_mpll (0), rate is 66666666
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c1abe000 s12480 r0 d16192 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519938
[ 0.000000] Kernel command line: vmalloc=512M debug_core.break_on_panic=0 debug_core.break_on_exception=0 no_console_suspend s3c2410-wdt.tmr_atboot=1 s3c2410-wdt.tmr_margin=30 wire.search_count=5 androidboot.hardware=manta s3cfb.bootloaderfb=0x60000000 androidboot.bootloader=MANTALJ09 androidboot.serialno=R32CB0185CM androidboot.wifimacaddr=BC:20:A4:79:C4:6E androidboot.btmacaddr=BC:20:A4:79:C4:6D
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] allocated 4192256 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 2047MB = 2047MB total
[ 0.000000] Memory: 1123232k/1123232k available, 972896k reserved, 648576K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xdf800000 - 0xff000000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdf000000 ( 496 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] .text : 0xc0008000 - 0xc08ca000 (8968 kB)
[ 0.000000] .init : 0xc08ca000 - 0xc09140c0 ( 297 kB)
[ 0.000000] .data : 0xc0916000 - 0xc09672e0 ( 325 kB)
[ 0.000000] .bss : 0xc09df668 - 0xc0ab0d48 ( 838 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:597
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000048] Calibrating delay loop... 997.78 BogoMIPS (lpj=2494464)
[ 0.030034] pid_max: default: 32768 minimum: 301
[ 0.030149] Security Framework initialized
[ 0.030173] SELinux: Initializing.
[ 0.030351] Mount-cache hash table entries: 512
[ 0.031044] Initializing cgroup subsys debug
[ 0.031056] Initializing cgroup subsys cpuacct
[ 0.031065] Initializing cgroup subsys memory
[ 0.031095] Initializing cgroup subsys freezer
[ 0.031132] CPU: Testing write buffer coherency: ok
[ 0.031262] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.031293] hw perfevents: enabled with ARMv7 Cortex-A15 PMU driver, 7 counters available
[ 0.031333] Setting up static identity map for 0x4071ba90 - 0x4071bae8
[ 0.093884] CPU1: Booted secondary processor
[ 0.121280] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.121319] CPU1: Unknown IPI message 0x1
[ 0.121446] Brought up 2 CPUs
[ 0.121458] SMP: Total of 2 processors activated (1995.57 BogoMIPS).
[ 0.133124] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[ 0.133321] gpiochip_add: registered GPIOs 0 to 7 on device: GPA0
[ 0.133333] gpiochip_add: registered GPIOs 9 to 14 on device: GPA1
[ 0.133344] gpiochip_add: registered GPIOs 16 to 23 on device: GPA2
[ 0.133355] gpiochip_add: registered GPIOs 25 to 29 on device: GPB0
[ 0.133364] gpiochip_add: registered GPIOs 31 to 35 on device: GPB1
[ 0.133374] gpiochip_add: registered GPIOs 37 to 40 on device: GPB2
[ 0.133383] gpiochip_add: registered GPIOs 42 to 45 on device: GPB3
[ 0.133393] gpiochip_add: registered GPIOs 47 to 53 on device: GPC0
[ 0.133403] gpiochip_add: registered GPIOs 55 to 58 on device: GPC1
[ 0.133412] gpiochip_add: registered GPIOs 60 to 66 on device: GPC2
[ 0.133421] gpiochip_add: registered GPIOs 68 to 74 on device: GPC3
[ 0.133431] gpiochip_add: registered GPIOs 76 to 79 on device: GPD0
[ 0.133440] gpiochip_add: registered GPIOs 81 to 88 on device: GPD1
[ 0.133450] gpiochip_add: registered GPIOs 90 to 95 on device: GPY0
[ 0.133459] gpiochip_add: registered GPIOs 97 to 100 on device: GPY1
[ 0.133468] gpiochip_add: registered GPIOs 102 to 107 on device: GPY2
[ 0.133478] gpiochip_add: registered GPIOs 109 to 116 on device: GPY3
[ 0.133487] gpiochip_add: registered GPIOs 118 to 125 on device: GPY4
[ 0.133497] gpiochip_add: registered GPIOs 127 to 134 on device: GPY5
[ 0.133506] gpiochip_add: registered GPIOs 136 to 143 on device: GPY6
[ 0.133515] gpiochip_add: registered GPIOs 145 to 151 on device: GPC4
[ 0.133525] gpiochip_add: registered GPIOs 153 to 160 on device: GPX0
[ 0.133534] gpiochip_add: registered GPIOs 162 to 169 on device: GPX1
[ 0.133543] gpiochip_add: registered GPIOs 171 to 178 on device: GPX2
[ 0.133553] gpiochip_add: registered GPIOs 180 to 187 on device: GPX3
[ 0.133567] gpiochip_add: registered GPIOs 189 to 196 on device: GPE0
[ 0.133577] gpiochip_add: registered GPIOs 198 to 199 on device: GPE1
[ 0.133586] gpiochip_add: registered GPIOs 201 to 204 on device: GPF0
[ 0.133595] gpiochip_add: registered GPIOs 206 to 209 on device: GPF1
[ 0.133604] gpiochip_add: registered GPIOs 211 to 218 on device: GPG0
[ 0.133613] gpiochip_add: registered GPIOs 220 to 227 on device: GPG1
[ 0.133623] gpiochip_add: registered GPIOs 229 to 230 on device: GPG2
[ 0.133632] gpiochip_add: registered GPIOs 232 to 235 on device: GPH0
[ 0.133641] gpiochip_add: registered GPIOs 237 to 244 on device: GPH1
[ 0.133655] gpiochip_add: registered GPIOs 246 to 253 on device: GPV0
[ 0.133665] gpiochip_add: registered GPIOs 255 to 262 on device: GPV1
[ 0.133674] gpiochip_add: registered GPIOs 264 to 271 on device: GPV2
[ 0.133683] gpiochip_add: registered GPIOs 273 to 280 on device: GPV3
[ 0.133692] gpiochip_add: registered GPIOs 282 to 283 on device: GPV4
[ 0.133704] gpio: GPZ has no PM function
[ 0.133713] gpiochip_add: registered GPIOs 285 to 291 on device: GPZ
[ 0.133928] dummy:
[ 0.134144] NET: Registered protocol family 16
[ 0.134479] Registered FIQ tty driver
[ 0.134514] Last reset was XnRESET pin reset (RST_STAT=0x10000)
[ 0.136730] Manta HW revision: 8, CPU EXYNOS5250 Rev1.0
[ 0.140206] console [ttyFIQ2] enabled
[ 0.140301] Registered fiq debugger ttyFIQ2
[ 0.140586] persistent_ram: found existing buffer, size 24788, start 24788
[ 0.203296] console [ram-1] enabled
[ 0.204992] bootloader fb located at 60000000-60F9FFFF
[ 0.205111] Registered chained gpio int handler for interrupt 77.
[ 0.205195] Registered interrupt support for gpio group 19.
[ 0.207404] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.207523] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.207708] S3C Power Management, Copyright 2004 Simtec Electronics
[ 0.208057] EXYNOS5250 PMU Initialize
[ 0.208950] EXYNOS: Initializing architecture
[ 0.209368] s3c24xx-pwm s3c24xx-pwm.0: tin at 33333333, tdiv at 33333333, tin=divclk, base 0
[ 0.209550] s3c24xx-pwm s3c24xx-pwm.1: tin at 16666666, tdiv at 16666666, tin=divclk, base 8
[ 0.216848] bio: create slab <bio-0> at 0
[ 0.217244] MXT_BOOSTER:
[ 0.217421] MXT_XVDD:
[ 0.217535] MXT_XVDD: supplied by MXT_BOOSTER
[ 0.217772] VBATT: 3700 mV
[ 0.615102] ion_chunk_heap_create: base 2415919104 size 268435456 align 1048576
[ 0.615680] SCSI subsystem initialized
[ 0.616518] usbcore: registered new interface driver usbfs
[ 0.616675] usbcore: registered new interface driver hub
[ 0.616820] usbcore: registered new device driver usb
[ 0.617124] wake enabled for irq 439
[ 0.617235] wake enabled for irq 432
[ 0.617345] wake enabled for irq 433
[ 0.617454] GPIO Input Driver: Start gpio inputs for manta-keypad... in interrupt mode
[ 0.617575] wake enabled for irq 427
[ 0.617683] GPIO Input Driver: Start gpio inputs for manta-keypad... in interrupt mode
[ 0.617873] input: manta-keypad as /devices/virtual/input/input0
[ 0.618085] input: manta-switch as /devices/virtual/input/input1
[ 0.618614] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[ 0.618726] s3c-i2c s3c2440-i2c.0: slave address 0x10
[ 0.618789] s3c-i2c s3c2440-i2c.0: bus frequency set to 65 KHz
[ 0.619183] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[ 0.619249] s3c-i2c s3c2440-i2c.1: slave address 0x10
[ 0.619357] s3c-i2c s3c2440-i2c.1: bus frequency set to 378 KHz
[ 0.619716] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
[ 0.619827] s3c-i2c s3c2440-i2c.2: slave address 0x10
[ 0.619890] s3c-i2c s3c2440-i2c.2: bus frequency set to 378 KHz
[ 0.620185] s3c-i2c s3c2440-i2c.3: i2c-3: S3C I2C adapter
[ 0.620251] s3c-i2c s3c2440-i2c.3: slave address 0x10
[ 0.620359] s3c-i2c s3c2440-i2c.3: bus frequency set to 378 KHz
[ 0.620664] s3c-i2c s3c2440-i2c.4: i2c-4: S3C I2C adapter
[ 0.620776] s3c-i2c s3c2440-i2c.4: slave address 0x10
[ 0.620839] s3c-i2c s3c2440-i2c.4: bus frequency set to 378 KHz
[ 0.621325] max77686 5-0009: device found
[ 0.628204] max77686_pmic_probe: Device ID=0x09, (version:1, chip_rev:1)
[ 0.628466] max77686-pmic max77686-pmic: Power on triggered by PWRON=High
[ 0.628532] max77686-pmic max77686-pmic: Power on triggered by Manual Reset Event
[ 0.631785] vdd_mif range: 850 <--> 1200 mV at 1037 mV
[ 0.632529] vdd_arm range: 850 <--> 1500 mV at 1075 mV
[ 0.633316] vdd_int range: 850 <--> 1300 mV at 1037 mV
[ 0.634059] vdd_g3d range: 850 <--> 1250 mV at 1200 mV
[ 0.635087] VCC_1.8V_AP: 1800 mV
[ 0.636067] VMIPI_1.0V: 1000 mV
[ 0.636841] TOUCH_VDD_1.8V: 1800 mV
[ 0.637871] VMIPI_1.8V: 1800 mV
[ 0.638839] VUOTG_3.0V: 3000 mV
[ 0.639810] VHSIC_1.0V: 1000 mV
[ 0.640787] VHSIC_1.8V: 1800 mV
[ 0.641577] 5M_CORE_1.5V: 1500 mV
[ 0.642294] CAM_IO_1.8V: 1800 mV
[ 0.643021] VT_CAM_1.8V: 1800 mV
[ 0.643790] TA_CHECK_1.35V: 1350 mV
[ 0.644516] TSP_AVDD_2.8V: 2800 mV
[ 0.645231] CAM_AF_2.8V: 2800 mV
[ 0.646202] VADC_3.3V: 3300 mV
[ 0.646850] 32KHZ_PMIC:
[ 0.647063] s3c-i2c s3c2440-i2c.5: i2c-5: S3C I2C adapter
[ 0.647128] s3c-i2c s3c2440-i2c.5: slave address 0x10
[ 0.647238] s3c-i2c s3c2440-i2c.5: bus frequency set to 378 KHz
[ 0.647508] s3c-i2c s3c2440-i2c.7: i2c-7: S3C I2C adapter
[ 0.647620] s3c-i2c s3c2440-i2c.7: slave address 0x10
[ 0.647682] s3c-i2c s3c2440-i2c.7: bus frequency set to 378 KHz
[ 0.647936] s3c-i2c s3c2440-i2c.8: i2c-8: S3C I2C adapter
[ 0.648001] s3c-i2c s3c2440-i2c.8: slave address 0x10
[ 0.648109] s3c-i2c s3c2440-i2c.8: bus frequency set to 378 KHz
[ 0.648228] Linux media interface: v0.10
[ 0.648372] Linux video capture interface: v2.00
[ 0.649822] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.650310] Bluetooth: Core ver 2.16
[ 0.650408] NET: Registered protocol family 31
[ 0.650471] Bluetooth: HCI device and connection manager initialized
[ 0.650584] Bluetooth: HCI socket layer initialized
[ 0.650646] Bluetooth: L2CAP socket layer initialized
[ 0.650773] Bluetooth: SCO socket layer initialized
[ 0.651126] cfg80211: Calling CRDA to update world regulatory domain
[ 0.651502] wake enabled for irq 421
[ 0.651634] wake enabled for irq 422
[ 0.652025] Switching to clocksource mct-frc
[ 0.668456] NET: Registered protocol family 2
[ 0.668686] IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.669141] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.670183] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 0.671278] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.671388] TCP: reno registered
[ 0.671453] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.671529] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.671810] NET: Registered protocol family 1
[ 0.672078] Trying to unpack rootfs image as initramfs...
[ 0.729783] Freeing initrd memory: 1244K
[ 0.731326] Exynos5 : ARM Clock down on idle mode is enabled
[ 0.731484] EXYNOS5250 ASV(ARM : 6 MIF : 2) using fused group
[ 0.731879] [BT] bcm_bt_lpm_init
[ 0.732110] wake enabled for irq 438
[ 0.732592] exynos_tmu exynos_tmu: Current auto refresh interval(3875 nsec), Normal auto refresh interval(3875 nsec), memory throttle auto refresh internal(1937 nsec)
[ 0.733745] exynos_tmu exynos_tmu: Tmu Initialization is sucessful...!
[ 0.733964] s3c-adc samsung-adc-v4: operating without regulator "vdd" .
[ 0.734095] s3c-adc samsung-adc-v4: attached adc driver
[ 0.734639] audit: initializing netlink socket (disabled)
[ 0.734730] type=2000 audit(0.725:1): initialized
[ 0.735542] highmem bounce pool size: 64 pages
[ 0.741211] fuse init (API version 7.18)
[ 0.741464] msgmni has been set to 929
[ 0.743146] io scheduler noop registered
[ 0.743214] io scheduler deadline registered
[ 0.743289] io scheduler row registered
[ 0.743417] io scheduler cfq registered (default)
[ 0.945979] dma-pl330 dma-pl330.0: Loaded driver for PL330 DMAC-267056
[ 0.946098] dma-pl330 dma-pl330.0: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.948258] dma-pl330 dma-pl330.1: Loaded driver for PL330 DMAC-267056
[ 0.948377] dma-pl330 dma-pl330.1: DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[ 0.949085] dma-pl330 dma-pl330.2: Loaded driver for PL330 DMAC-267056
[ 0.949154] dma-pl330 dma-pl330.2: DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[ 0.949379] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.950120] exynos4210-uart.0: ttySAC0 at MMIO 0x12c00000 (irq = 83) is a S3C6400/10
[ 0.950312] exynos4210-uart.1: ttySAC1 at MMIO 0x12c10000 (irq = 84) is a S3C6400/10
[ 0.950546] exynos4210-uart.3: ttySAC3 at MMIO 0x12c30000 (irq = 86) is a S3C6400/10
[ 0.950886] mali mali.0: Continuing without Mali clock control
[ 0.951998] mali mali.0: GPU identified as 0x6956 r0p0 status 1
[ 1.088187] mali mali.0: Probed as mali0
[ 1.088423] mali mali.0: start latency exceeded, new value 958 ns
[ 1.089362] mali mali.0: state restore latency exceeded, new value 822666 ns
[ 1.089434] mali mali.0: stop latency exceeded, new value 875 ns
[ 1.094319] brd: module loaded
[ 1.096675] loop: module loaded
[ 1.097558] WM1811 LDO1:
[ 1.098053] WM1811 LDO2:
[ 1.102571] wm8994 7-001a: WM1811 revision D CUST_ID 00
[ 1.106510] bcm2079x-spi spi2.0: bcmspinfc_probe, probing bcmspinfc driver
[ 1.106700] bcm2079x-spi spi2.0: requesting IRQ 430
[ 1.106821] bcm2079x-spi spi2.0: bcmspinfc_probe, probing bcmspinfc driver exited successfully
[ 1.107088] tun: Universal TUN/TAP device driver, 1.6
[ 1.107151] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[ 1.107370] PPP generic driver version 2.4.2
[ 1.107532] PPP BSD Compression module registered
[ 1.107644] PPP Deflate Compression module registered
[ 1.107975] PPP MPPE Compression module registered
[ 1.108089] NET: Registered protocol family 24
[ 1.108188] usbcore: registered new interface driver asix
[ 1.108282] usbcore: registered new interface driver cdc_ether
[ 1.108417] usbcore: registered new interface driver net1080
[ 1.108505] usbcore: registered new interface driver cdc_subset
[ 1.108638] usbcore: registered new interface driver zaurus
[ 1.108789] usbcore: registered new interface driver cdc_ncm
[ 1.108981] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.109363] s5p-ehci s5p-ehci: S5P EHCI Host Controller
[ 1.109543] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[ 1.109714] s5p-ehci s5p-ehci: irq 103, io mem 0x12110000
[ 1.117202] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
[ 1.117381] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.117447] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.117557] usb usb1: Product: S5P EHCI Host Controller
[ 1.117619] usb usb1: Manufacturer: Linux 3.4.67 ehci_hcd
[ 1.117727] usb usb1: SerialNumber: s5p-ehci
[ 1.118103] hub 1-0:1.0: USB hub found
[ 1.118226] hub 1-0:1.0: 3 ports detected
[ 1.118505] s5p-ehci s5p-ehci: remove, state 1
[ 1.118577] usb usb1: USB disconnect, device number 1
[ 1.119856] s5p-ehci s5p-ehci: USB bus 1 deregistered
[ 1.120123] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.120447] exynos-ohci exynos-ohci: EXYNOS OHCI Host Controller
[ 1.120633] exynos-ohci exynos-ohci: new USB bus registered, assigned bus number 1
[ 1.120777] exynos-ohci exynos-ohci: irq 103, io mem 0x12120000
[ 1.176284] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.176399] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.176510] usb usb1: Product: EXYNOS OHCI Host Controller
[ 1.176572] usb usb1: Manufacturer: Linux 3.4.67 ohci_hcd
[ 1.176680] usb usb1: SerialNumber: exynos-ohci
[ 1.177025] hub 1-0:1.0: USB hub found
[ 1.177100] hub 1-0:1.0: 3 ports detected
[ 1.177431] exynos-ohci exynos-ohci: remove, state 1
[ 1.177502] usb usb1: USB disconnect, device number 1
[ 1.178015] exynos-ohci exynos-ohci: USB bus 1 deregistered
[ 1.178292] usbcore: registered new interface driver usblp
[ 1.178402] Initializing USB Mass Storage driver...
[ 1.178493] usbcore: registered new interface driver usb-storage
[ 1.178602] USB Mass Storage support registered.
[ 1.178936] s3c-hsotg : S3C HS USB OTG Device Driver,(c) 2008-2009 Samsung Electronics
[ 1.178943] s3c-hsotg : version 15 March 2009
[ 1.179261] file system registered
[ 1.180162] gadget: Mass Storage Function, version: 2009/09/11
[ 1.180277] gadget: Number of LUNs=1
[ 1.180341] lun0: LUN: removable file: (no medium)
[ 1.180674] gadget: android_usb ready
[ 1.180738] bound driver 'android_usb'
[ 1.180921] mousedev: PS/2 mouse device common for all mice
[ 1.181226] usbcore: registered new interface driver xpad
[ 1.181319] usbcore: registered new interface driver usb_acecad
[ 1.181455] usbcore: registered new interface driver aiptek
[ 1.181541] usbcore: registered new interface driver gtco
[ 1.181674] usbcore: registered new interface driver hanwang
[ 1.181760] usbcore: registered new interface driver kbtab
[ 1.181893] usbcore: registered new interface driver wacom
[ 1.182388] input: Atmel maXTouch Touchscreen as /devices/platform/s3c2440-i2c.3/i2c-3/3-004a/input/input2
[ 1.192364] mali mali.0: stop latency exceeded, new value 959 ns
[ 1.192496] mali mali.0: state save latency exceeded, new value 8375 ns
[ 1.192851] pd-g3d: Power-off latency exceeded, new value 286958 ns
[ 1.292779] max77686-rtc max77686-rtc: max77686_rtc_enable_wtsr_smpl: WTSR: enable, SMPL: enable
[ 1.392693] max77686-rtc max77686-rtc: rtc core: registered max77686-rtc as rtc0
[ 1.393279] i2c /dev entries driver
[ 1.393982] exynos-mdev.0: Media0[0xde147800] was registered successfully
[ 1.394177] exynos-mdev.1: Media1[0xde147c00] was registered successfully
[ 1.394369] exynos-mdev.2: Media2[0xde19c000] was registered successfully
[ 1.394947] [INFO]gsc_probe:1450: gsc-0 registered successfully
[ 1.395461] [INFO]gsc_probe:1450: gsc-1 registered successfully
[ 1.395921] [INFO]gsc_probe:1450: gsc-2 registered successfully
[ 1.396419] [INFO]gsc_probe:1450: gsc-3 registered successfully
[ 1.396533] Initialize JPEG driver
[ 1.396807] s5p-jpeg s5p-jpeg: JPEG driver is registered to /dev/video12
[ 1.396938] s5p-jpeg s5p-jpeg: JPEG driver is registered to /dev/video11
[ 1.397382] Samsung Graphics 2D driver, (c) 2011 Samsung Electronics
[ 1.397489] EXYNOS MFC V4L2 Driver, (c) 2010 Samsung Electronics
[ 1.397926] s5p-mfc s5p-mfc: decoder registered as /dev/video6
[ 1.398059] s5p-mfc s5p-mfc: encoder registered as /dev/video7
[ 1.398621] i2c i2c-0: attached exynos hdcp into i2c adapter successfully
[ 1.398764] i2c-core: driver [exynos_hdcp] using legacy suspend method
[ 1.398827] i2c-core: driver [exynos_hdcp] using legacy resume method
[ 1.398946] Samsung HDMI output driver, (c) 2010-2011 Samsung Electronics Co., Ltd.
[ 1.399158] s5p-hdmi exynos5-hdmi: hdmiphy i2c bus number = 8
[ 1.399348] s5p-hdmiphy 8-0038: hdmiphy_probe start
[ 1.399414] s5p-hdmiphy 8-0038: probe successful
[ 1.425083] s5p-hdmi exynos5-hdmi: probe sucessful
[ 1.425258] i2c i2c-0: probed exynos edid
[ 1.425365] Samsung TV Mixer driver, (c) 2010-2011 Samsung Electronics Co., Ltd.
[ 1.425519] s5p-mixer s5p-mixer: probe start
[ 1.425802] s5p-mixer s5p-mixer: resources acquired
[ 1.425890] s5p-mixer s5p-mixer: added output 'S5P HDMI connector' from module 's5p-hdmi'
[ 1.426106] s5p-mixer s5p-mixer: registered layer mxr0_graph0 as /dev/video16
[ 1.426245] s5p-mixer s5p-mixer: registered layer mxr0_graph1 as /dev/video17
[ 1.426436] s5p-mixer s5p-mixer: registered layer mxr1_graph2 as /dev/video18
[ 1.426616] s5p-mixer s5p-mixer: registered layer mxr1_graph3 as /dev/video19
[ 1.426682] s5p-mixer s5p-mixer: mixer0 create links
[ 1.426801] s5p-mixer s5p-mixer: mixer1 create links
[ 1.426871] s5p-mixer s5p-mixer: mixer links are created successfully
[ 1.426995] s5p-mixer s5p-mixer: probe successful
[ 1.428101] fimc_is_spi successfully probed
[ 1.428187] Driver for 1-wire Dallas network protocol.
[ 1.500042] wake enabled for irq 420
[ 1.500412] s3c2410_wdt: S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
[ 1.500665] s3c2410-wdt s3c2410-wdt: starting watchdog timer
[ 1.500735] s3c2410-wdt s3c2410-wdt: watchdog active, reset enabled, irq disabled
[ 1.501243] device-mapper: uevent: version 1.0.3
[ 1.501481] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected]
[ 1.501897] Bluetooth: HCI UART driver ver 2.2
[ 1.502010] Bluetooth: HCI H4 protocol initialized
[ 1.502210] cpuidle: using governor ladder
[ 1.502414] cpuidle: using governor menu
[ 1.502548] sdhci: Secure Digital Host Controller Interface driver
[ 1.502611] sdhci: Copyright(c) Pierre Ossman
[ 1.502798] Synopsys Designware Multimedia Card Interface Driver
[ 1.502964] dw_mmc dw_mmc.0: Using internal DMA controller.
[ 1.503389] mmc0: no vmmc regulator found
[ 1.505370] dw_mmc dw_mmc.0: Version ID is 241a
[ 1.505449] dw_mmc dw_mmc.0: DW MMC controller at irq 107, 32 bit host data width, 128 deep fifo
[ 1.505664] dw_mmc dw_mmc.1: Using internal DMA controller.
[ 1.506044] mmc1: no vmmc regulator found
[ 1.507344] dw_mmc dw_mmc.1: Version ID is 241a
[ 1.507412] dw_mmc dw_mmc.1: DW MMC controller at irq 108, 32 bit host data width, 128 deep fifo
[ 1.507523] dw_mmc dw_mmc.1: Internal DMAC interrupt fix enabled.
[ 1.517567] usbcore: registered new interface driver usbhid
[ 1.517691] usbhid: USB HID core driver
[ 1.532218] mmc_host mmc0: device is being hw reset
[ 1.692231] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
52 Corrected bytes, 0 unrecoverable blocks
Last reset was software reset (RST_STAT=0x20000000)
I have no idea what is missing but the display doesn't show anything when booting with a self compiled permissive kernel....
Just to let you all know
scanno said:
Just to let you all know
Click to expand...
Click to collapse
Nice. Looking forward to seeing how far this goes. How's it running?
jsgraphicart said:
Nice. Looking forward to seeing how far this goes. How's it running?
Click to expand...
Click to collapse
Too early to tell. Just got it booting. Wifi is working. Camera and gps not yet. BT and NFC not tried yet.
scanno said:
Too early to tell. Just got it booting. Wifi is working. Camera and gps not yet. BT and NFC not tried yet.
Click to expand...
Click to collapse
Well it's exciting to actually see it being done. I was afraid we wouldn't get anything for our Nexus 10
scanno said:
Too early to tell. Just got it booting. Wifi is working.
Click to expand...
Click to collapse
Don't need anything else!
scanno said:
Too early to tell. Just got it booting. Wifi is working. Camera and gps not yet. BT and NFC not tried yet.
Click to expand...
Click to collapse
Which kernel did you use?
aHcVolle said:
Which kernel did you use?
Click to expand...
Click to collapse
I used my own kernel (well the omnirom kernel and selinux patches).
This weekend i will sort out the patches and commit them.
You can check https://gerrit.omnirom.org/#/q/stat...anta+branch:android-7.0+topic:manta-n-bringup
I have most of them there already, but not yet verified by a new build.
---------- Post added at 10:36 AM ---------- Previous post was at 10:35 AM ----------
peachpuff said:
Don't need anything else!
Click to expand...
Click to collapse
Will upload the boot.img and system.img tonight.
But ut is a first booting build,expect problems and at your own risk. Only flashable by fastboot.
---------- Post added at 11:36 AM ---------- Previous post was at 10:36 AM ----------
https://www.androidfilehost.com/?w=files&flid=109935
Completely at your own risk
Wipe in twrp
Reboot into bootloader
fastboot flash boot boot.img
fastboot flash system system.img
fastboot reboot
And cross your fingers
Flashing system.img will give a signature failure, but it boots fine for me
So I'm new to xda, but this forum has been very helpful in my research and digging into this little gadget.
My girlfriend picked it up online on some auction site for $3, ~$10 total shipped..
I've lurked quite a bit and haven't found anyone with the exact same model as mine, although it may just be a software difference.
Anyway, here's what I've found out.
dmesg:
[ 457.431574] usb 3-2: New USB device found, idVendor=0e8d, idProduct=0003
[ 457.431579] usb 3-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 457.488571] cdc_acm 3-2:1.1: ttyACM0: USB ACM device
[ 457.488894] usbcore: registered new interface driver cdc_acm
[ 457.488896] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 457.496454] usbcore: registered new interface driver usbserial
[ 457.496504] usbcore: registered new interface driver usbserial_generic
[ 457.496544] usbserial: USB Serial support registered for generic
[ 457.514004] usbcore: registered new interface driver option
[ 457.514718] usbserial: USB Serial support registered for GSM modem (1-port)
[ 460.031180] usb 3-2: USB disconnect, device number 3
[ 469.379588] usb 3-2: new full-speed USB device number 4 using xhci_hcd
[ 469.522639] usb 3-2: New USB device found, idVendor=0e8d, idProduct=0002
[ 469.522644] usb 3-2: New USB device strings: Mfr=2, Product=3, SerialNumber=4
[ 469.522646] usb 3-2: Product: CARNEO
[ 469.522648] usb 3-2: Manufacturer: MediaTek Inc
[ 469.522649] usb 3-2: SerialNumber: 532598606846370
[ 469.617795] usb-storage 3-2:1.0: USB Mass Storage device detected
[ 469.617894] scsi host6: usb-storage 3-2:1.0
[ 469.618060] usbcore: registered new interface driver usb-storage
[ 469.622778] usbcore: registered new interface driver uas
[ 470.640854] scsi 6:0:0:0: Direct-Access MEDIATEK FLASH DISK PQ: 0 ANSI: 0 CCS
[ 470.641722] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 470.642509] sd 6:0:0:0: [sdb] 15564800 512-byte logical blocks: (7.97 GB/7.42 GiB)
[ 470.643253] sd 6:0:0:0: [sdb] Write Protect is off
[ 470.643258] sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00
[ 470.643836] sd 6:0:0:0: [sdb] No Caching mode page found
[ 470.643842] sd 6:0:0:0: [sdb] Assuming drive cache: write through
lsusb:
-Watch powered on, no selection made (usb charging)
Bus 003 Device 004: ID 0e8d:0002 MediaTek Inc.
-Watch powered on, selected com port from menu
Bus 003 Device 008: ID 0e8d:0003 MediaTek Inc. MT6227 phone
Device info from menus/dialer codes:
[VERSION]
NX9_COB_V1_1_G09_B_HC_IPS_170516_1041
[BRANCH]
11CW1352MP
GPLUS61A_11C_NX9
BUILD:BUILD_NO
SERIAL#:
[BUILD TIME]
2017/05/16 10:41
[MRE VERSION] 3100
HAL_VERNO:
mtk soft ver: 0x1308
mtk hw ver: unknown
ver: 0x74
userid: 0
os: mtk52d
osvern:
model:c1
company:f001
width:0, height:0
maxram:716800
kbd:0
touchscreen:1
cap:0x40010
macro:
fae:dongming
build date: 20170516
buildtime: 2017/05/16 10:41
MRE
[version] 3100
[build time] 2017/05/16 10:41
[mem size] 888868
[support modules]
base
resmrg
comm
sm
resmrgc
ch
draw
gfxold
image
http
IMEIini
mul
xml
aud
camera
cell
pb
sim
sms
soc
status
tel
timer
launch
Dialer codes I found in the rom and tested:
*#9966*# engineering mode ?
*#0000# english
*#00000000# menu (needs sim)
*#6810# ???
*#931# ???
*#902# ???
*#932# ???
*#903# ???
*#993646633# menu of some sort
*#1234# BT mode
*#0044# set language to eng
*#63342835# mtk logo
*#8375# build info
*#06# imei
*#9987# quick test
A2DP ACP Mode: *#1234#
A2DP INT Mode: *#1234#
[MEM TEST]
=============== Memory Detection Report ===============
Internal RAM: Size = 0x0000D000 (52KB)
External RAM: Type = SRAM
Size = 0x00400000 (4MB/32Mb)
NOR Flash: Device ID = "[Winbond] SF_W25Q32JV" (275)
Size = 0x00400000 (4MB/32Mb)
NAND Flash: ERROR: NAND Flash wasnt detected!
cpu/pcb: drive [dot] google[dot]com/file/d/0BzNc0mWX8OZGRkszQXRLZXcxbFU/view?usp=sharing
Identifying mark? drive [dot] google[dot]com/file/d/0BzNc0mWX8OZGTk44VGYxbGNmWGs/view?usp=sharing
Extracted FW: drive[dot]google[dot]com/open?id=0BzNc0mWX8OZGUzJBZEI3R21WYm8
Raw Readback: drive[dot]google[dot]com/open?id=0BzNc0mWX8OZGM0xJVnUyekdHZkU
note: my master copy of the firmware has original bootlogo, but also has my address book & contacts in it, this is a restored/cleaned fw dump, but it has a custom boot animation (rotating picture of dickbutt) I have added.
I've been digging around in the rom, trying to figure out how to remove apps from the firmware to free up space, or possibly add new apps.
I found www[dot]dr-lex[dot]be/hardware/china_phone_flashing[dot]html , which has been very helpful but I'm not able to mount the partition as described in the post.
I'm a regular linux user and have done a bit of cross compiling stuff for my raspi, so i'm kind of curious if theres any info on how to get custom code running on these.
I've found these, but haven't had a chance to dig into them as of yet.
github[dot]com/xobs/fernvale-qemu
github[dot]com/xobs/fernly
In addition to the info above I have a few questions:
Does anyone have any sort of info on how to cut stuff out of the rom or possibly swap apps?
In regards to the CPU, I'm sure its arm, but is it armv5 v6 v7 ?
Has anyone dug into the internals of the nucleus OS?