Database Users

[Q] First blue screen, now boot loop.

Hello XDA-devs forums,
I'm having an issue since yesterday.
I have rooted my Huawei Ideos X5, and it ran fine for a day or so.
However, when my battery ran out it shut down into a completely blue screen.
When I tried booting it again, this just showed me a blue screen as well.
Now, I fixed this issue by connecting the phone to my PC after booting it with the Vol+ and Vol- pressed.
(So you get the pink/purple screen)
However, when I opened the phone on my PC, all I saw was a "239 MB" "empty" space, and it should have ~2GB..
I placed a backup copy I saved of my "image" folder in that 239 MB storage, and it booted.
However, today I hooked it up to my PC again to see if it magically changed..
And I couldn't access the 239 MB space anymore.
When I tried fixing the issue with a reboot of the phone, that just caused it to get stuck in a booting loop.
So now I'm stuck with a phone that keeps trying to boot itself,
and I can't access it on my windows PC.
I can, however, access 4 different folders of the phone on my linux notebook.
Now, my question is: can someone with a good understanding of problems like these please help me out?
I'm getting kind of fed up with it, as I've only got the phone for 2 days now.
Thank you in advance, and thank you for taking the time to read this.

Have you tried removing the battery for 5 minutes and then putting it back in?
After this, what happens when you press VOL+ and Power?
How about if you press VOL+, VOL- and Power, without the USB cable?

Hello Katu, thank you for posting.
Regarding your questions:
Yes, I have tried to take out the battery for 5+ minutes- it didn't change anything to the situation unfortunately..
If I press VOL+ and Power at the same time, the device boots into recovery mode.
In this I have tried to format the device in order to reset it to factory defaults, but this did not help either.
When I press VOL+, VOL- and Power, the phone boots into the pink/purple screen.

Can you try a custom recovery and a custom rom? I want to see if your onboard flash is borked.
u8800,cm7,[email protected]

I had the same when my phone got f*ucked up. Put the image folder, than download official rom, like b138 and install it. then check your imei. There is a change that it will be 0.

PlanDreaM said:
Can you try a custom recovery and a custom rom? I want to see if your onboard flash is borked.
u8800,cm7,[email protected]
Click to expand...
Click to collapse
Well, I used an original ROM:
U8800 V100R001C00B136(Overseas General version)
And that resulted in the boot.img being corrupted, so I can't even overwrite that anymore.
Also, this is what I see when I hit VOL+, VOL- and Power at the same time to boot into safe mode, and connect it to my PC.
img69 [dot] imageshack [dot] us/img69/244/10101191548pm.png
julle131 said:
I had the same when my phone got f*ucked up. Put the image folder, than download official rom, like b138 and install it. then check your imei. There is a change that it will be 0.
Click to expand...
Click to collapse
I installed the official B136 rom, and after it rebooted, it would just hang on a black screen.
(it used to show the IDEOS or Android logo when it booted)

Hmm mine came with this Rom
U8800 V100R001C00B135SP01 ( general )
Looking at your name you're from the Netherlands ( so am I )
where did you get this 136 version from ?
I would try to put this one on it
You have to put the 'dload' folder into the root of your SD Card,
then boot into boot-loader, after that it'll automatically flash back to the stock Rom.
1 Format SD card
2 On the SD card, create "dload" folder
3 Put the unzipped Rom into "dload" folder
4 Then boot to bootloader (pink screen)

Yes, mine came with that version as well.
However, I couldn't find it anymore and thus downloaded the version I said earlier.
Also, I did everything as you described, except step 4.
You have to boot to recovery instead of bootloader. (VOL+ and Power)
Anyways, I managed to get ClockworkMod's recovery.img on my phone,
and from there on install a custom ROM on the phone, which magically got it working again - even though it didn't work earlier.
Thank you for reading my thread and taking the time to reply to it.
My issue has been resolved.

just for the record, flashing a stock rom is different from flashing a custom rom..
the 4 steps described by Gman2oo6 is the correct way to flash a stock rom (and it is written clearly in the document that is in the stock rom zip file)
[edit]
step (1) is not a necessary step though..

Yeah, I noticed that.
What I did was format my SDcard with FAT32,
and put a custom rom (update.zip) on the SDcard.
I then booted ClockworksMod Recovery and installed the custom rom from the SDcard.
When I tried installing the stock rom, I just followed the PDF file's instructions that came with the stock rom.

hey i udated to GB 2.3.4 (official)and i didnt like the it cuz the wifif ddnt work and the bluetooth also the DATA so itryed to downgrade to 2.2.2 original official and it did the 2/2 steps intalled and when it restarted it did not want to turn on all that happened was it vibrated and thats all so i left it on like that and when the battery died i plugged it in to the AC and the LED turned on red and the touch kkeys also but not the screen so i really NEED help!

Try to turn it on with lead connected but no battery and see if you can start it.
My battery also went dead flat this morning and I couldn't get it started at all till I tried this. Once I got it started the only thing I could do was quickly pop in the batery and let it charge. Just leave off the cover till you get it going.
I have to add that I did not have the problem of a failed update to deal with but it may at least get you started

i tryed it
nope nothin good happened all that happens is a blank screen with nothin on ,LED is off and the touch keys are off. it justz vibrates and when i put the battery it turn the LED on to red and the touch keys turn on but then like 5 min later the LED and keys turn off

astewart said:
Try to turn it on with lead connected but no battery and see if you can start it.
My battery also went dead flat this morning and I couldn't get it started at all till I tried this. Once I got it started the only thing I could do was quickly pop in the batery and let it charge. Just leave off the cover till you get it going.
I have to add that I did not have the problem of a failed update to deal with but it may at least get you started
Click to expand...
Click to collapse
ok heres what i did i wanted to upgrade my phone to the newest version GB 2.3.4.So what i did was download the update and i followed the installation steps i successfully updated to Gb 2.3.4. so like i was checking how it look and the new feature but when i wanted to go on the android market i went to setting and turn on the wifi and it said Error and then i tried the Bluetooth and it said Error also so then i put my SIMs card in and i was like imma use DATA then and when i restarted my phone it had service but no HSPA+ or Edge or GPRS so like i just hatted my phone from their so then i was trying to root it but iddnt know how to do that so like i read this website and i got the UPDATE.APP or 2.2.2 AT&T did the same steps of the installation of BG 2.3.4 and it went to the process and 1/2 stepp good it passed and then 2/2 also passed it installed it and when it said Successively Installed it said Restarting and the scrren turn of and it vibrated and thats all that happened and i left it like that for the whole days and nothing happened
Do u got any idea?
When i connect it to my laptop it says installing drivers .then its says sucesfully installed drivers ready to use. so then i got to Device Manger and i check what has been installed and their it said USB Human interface device and HID-compliant device WHAT DOES THAT MEAN??

Not sure about the HID (human interface device) probably just the way windows sees the device for interfacing with it. With regards to the not booting I have read a lot of people saying that you need to factory reset and clear cache after the upgrade/downgrade. With the phone off, turn it on by long pressing volume+ and power on button till you get the blue recovery screen and from there you can reset factory/ data and also clear the cache. from what I see this should clear up the problem and start up. Please read this thread, it may help you somehow..... http://forum.xda-developers.com/showthread.php?t=1420728
Hope this helps a little

U mean Boot recovery and imma try it and thanks ill check it out
Sent from my MB300 using XDA App

all that i know is that if u customized your partition, it'll bootloop,
so go back to stock-partition ^^

How do I do that got like the steps or video?
Sent from my MB300 using XDA App
when i downgraded to 2.2.2 i installed this V100R001C00B138SP04CUSTC185D002
http://forum.xda-developers.com/showthread.php?t=1251250 got it from that link

Looks like you are not having much luck. Did you try to factory reset?

astewart said:
Looks like you are not having much luck. Did you try to factory reset?
Click to expand...
Click to collapse
well how do i do that do i need to got to the purple/pink screen or bot recovery cuz i cannot access that my phone doesn't do anything pretty much

[Q] My phone is dead on stock...(due to rooting/unlocked failure?) Please help!

Hello XDAers,
I am a real noob at rooting or android-related, and a true one voided of any knowledge regarding anything IT- related.
So dear veterans, please go easy on me.
Due to my prior success of rooting and flashing my Nexus 4 successfully a few months back with no issues, I decided to give it a try to flash a custom ROM for my dad's LG Optimus L7 - which seemed an easy task compared to configuring my Nexus 4 - since there was no need for inputting any command lines or any dealing with the abd (using the easy shortcut, that is).
So, I followed the guide here: http://forum.xda-developers.com/showthread.php?t=1906133 ...
I first factory resettled the phone because it was bloated, then applied the "RunMe.bat" from the "What you desire!" folder. (Everything was already backed-up beforehand.) But the process didn't success until I've retried again and again by re-plugging the USB in because the application/PC couldn't detect the phone. In the same time, I was running KDZ_FW_UPD.exe in the background, so unexpectedly for me the phone shut itself and pushed itself to a vividly green emergency screen, then in a few seconds switched back to a screen of purple-white-blue glitches. I had to close KDZ_FW_UPD.exe without knowing what quite happened since it seemed to be the cause and restarted the process with RunMe.bat.
I didn't manage to "Restore" it first due to the fact that the phone stopped responding due to a lag asking for an encryption key. It was lagging so hard and I had to close the cmd around 5 tries while it was processing, but succeeded later on.
And then, to verify whether I've actually suceeded in rooting L7, I installed Root Checker from the Play Store. And again, for the first few tries the program froze on screen for a long period of time due to "system performance", but after rebooting and restarting the app a few times again, the ROOTING proves to be a success. Just to be sure, around this time I've reloaded KDZ_FW_UPD.exe and it suceeded.
So I went to install CWM and ES. CWM for recovery boot and ES for removing pre-installed system apps as the phone was lagging so badly. I've downloaded the CWM restoring(something like ~6.0.28?) first and tried fastbooting immediately right after, but instead of getting the fastboot menu I got a screen emptied in black with these words:
[5020] "Secure booting error"
[5020] "Cause: boot certification verify"
No hard keys could do anything on the presumed "fastboot", and so I had to hard boot again. I thought that it might be due to the lack of memory(checked on ES later on that it was 310~MB/2GB), and so I've used ES to uninstall a lot of system apps which I deemed uneccessary. So I've Googled a bit and it became apparent to me that that I've didn't unlock the device properly, so lurked around and found a file called L7CWM that is supposedly to resolve my problem, but I presume that it's the CWM recovery image that I've installed. So in the end, I didn't bother with it but kept it on tab just in case.
I repeated the same process with CWM again, but this time, the screen was joined with all kinds of flowery glitches. Restarted the device, and it went only downhill: now the Home launcher stayed all pitch black and nothing appeared. I waited a few minutes, but nothing there until the notification bar appeared. The home screen is apparently dead, and so are the menu keys. Switched to Nova Launcher(installed it just in case Home Launcher fails), and still dead. I couldn't access using any of the menu keys and had unusable launchers.
Hopefully I could still access to the settings from my status bar, but when I did, it started crashing immediately.
I've repeated the attempt a few times after restarting the device a few times, but nothing helped. It only got worse that the when the launcher did SEEM to work. It only showed the wallpaper without showing any of the icons/apps. And crashes again.
I could still access to the App menu via the settings, but couldn't open any of them and when I tried to uninstall them, the screen frozes immediately right after I gain access to the page (white page though) and gain this message: "Unfortunately Package Uninstaller Stopped!"
Then I convinced myself that the only thing I could do at the time was to factory reset the phone and then everything would go alright since I've just had to restore the system apps.
But then the black screen of death came right along with it:
"Secure booting error"
It seems that I'm out of luck... ... But just to check if I'm still left with resorts, I've downloaded the L7CWM file online...
... ...but it still didn't help.
So now I'm being left with no other choices other than asking for help. I never really understand what KDZ_FW_UPD.exe does since I had the LG Driver already before installing it, which I presume was for updating the phone to a newer or older version. And too complex tech articles are kind of alien for me.
EDIT(1 hour later): Okay, now I figured out the reason why L7CWM didn't work was because I didn't extract it to the right folder (after double checked via notepad that I was supposed to directly put it into the C:\ drive). Now it worked(?), but then it didn't.
After launching Flash_Bootloader.bat:
This message now appeared on the L7:
"Sorry!"
"SuperSU is not responding.
Would you like to close it?"
"Wait - Report - Close"
and a few minutes later
"Sorry!"
"Unfortunately, SuperSU has stopped."
"Report - OK"
Now I think the bugs till now happened was due to the fact that I've deleted a file that was required for me to launch apps... Now I just need the right fix.
After 5 minutes of screen inactivity the phone restarted by itself, kind of creepy... ...
Flash_Recovery.bat did nothing.
Reboot2Recovery.bat made it reboot but still struck on the same menu.
Nothing seems to be effective via the phone anymore, seems like I have to rely on abd but then again I don't know how... ... My dad is also f*cking pissed off ^ ^;...
__________________________________
I think that I explained the logs pretty precisely in case I missed something... I'll be very very very very very very thankful if someone could tell me what has caused my phone to fail though.
For references, here are the phone's specifications:
Model Number: LG-P705g
Android version: 4.0.3 (Stock)
Rooted:Yes (root checker)
Baseband version: MSM7227A-1-AA
Kernel version: 3.0.8-perf
Build number: IML74K
Software version: V10e-AUG-10-2012
If I don't get the phone fixed to being usable soon I think that I will get butchered real hard... ... Preferably needs a step-by-step guide made for toddlers... ...

remove the battery for 10 seconds,put it back pres VOL+ and VOL - same time and than press the power button.when you feel a vibration press for many times the button wich is down in right,try for many times and maybe it will working :}

Cydes said:
Hello XDAers,
If I don't get the phone fixed to being usable soon I think that I will get butchered real hard... ... Preferably needs a step-by-step guide made for toddlers... ...
Click to expand...
Click to collapse
simple answer for your
just download your stock rom
go to emergency mode
and flash that stock rom

"Setup assistent has been closed" loop after flashing gApps

Hey guys,
I flashed this ROM on my LG G2 (802) http://forum.xda-developers.com/lg-g2/development/rom-official-mokee-source-project-t3274849/page2. Everything has been okay so far.
In the Mokee thread I read installing gApps would work like this:
"you can go MokeeCenter after starting rom, there you can download the small gapps integrated into the system and have a lighter and clean rom."
Unfortunally for me there was no option to download gApps via "MokeeCenter". Of course I found Settings -> MokeeCenter.
So I decided to download open_gapps-arm-6.0 (has been the minimal version, I think) and flashed it.
After I rebooted into system, I now am stuck at a popup which immediately and continiously pops up, saying "setup assistent has been closed". So I cannot do anything else than pressing "ok ok ok ok ok ok"
Big problem for me now is, that for some unknown reason, I cannot boot into twrp recovery using one of the hardkey methods.
I usually was able to do it like this:
- Shut down.
- Press power + volume down until LG logo appears.
- Release only power button, then immediately press power button again (while still pressing volume down).
I think I now tried any of the other methods as well (power + volume up instead of down... or release power AND volume down, then press both again... and so on...)
None of them work for me.
I might have to mention, that after the first appear of the popup loop, I read something about flashing "bootstack-d802-CAF-signed" as part of a solution.
I did so, but it diddn't help. Instead of a solution this might be part of my problem, because since I was able to flash it I obvously must have been able to enter twrp before this step.
What should I do now?
By the way: Can some of you tell me, if the annoying crackle/hissing of my headphones is gone with Android M?
I want to know this, because this has been the ONLY reason for me to flash Android M, since I wasn't able to find a solution for Android Lollipop (CM12). I find it extremely (!) uncomfortable to talk to people using my bose qc25 headphones/headset since my Lollipop update, because everytime when a person speaks just a few words with longer pauses between the single words, I have sound errors and hissing/crackles and even some really wired kind of "distortion" at the beginning of each single word and often have to ask people to repeat what they said.
The headphones themselves sound absolutely okay, it's just with the LG G2 phone. (i.e. a friend's Samsung S5 works fine with the bose qc25)
If this bug isn't gone with Android M (or at least fixable) I think I will buy a new cellphone instead of trying to unbrick my LG G2 if unbricking will be a pain in the ass, so I am very interested in an answer regarding the sound bug as well.
Thank you for reading.
with best regards,
Milan

I now have been able to setup a guest account. Running the guest account, I can quit the popup by pressing "ok" once. It doesn't return and is followed by "Gallery stopped" which I am able to quit too. But as guest I cannot get root access to use a software based reboot to recovery, right?

follow these steps
1. go to settings and find applications menu
2. select find system applications from menu
3. find installiation wizard or something else (i am using my rom in Turkish "Kurulum Sihirbazı".
4. click on it and edit permissions
5. enable people and phone sections.
6. cheers

gttrk said:
1. go to settings and find applications menu
2. select find system applications from menu
3. find installiation wizard or something else (i am using my rom in Turkish "Kurulum Sihirbazı".
4. click on it and edit permissions
5. enable people and phone sections.
6. cheers
Click to expand...
Click to collapse
Thank you
Problem was, I could not navigate because there has been this fu*** popup always on top.
I have been able to enable root access and advanced shutdown options by clicking almost 1000 times "ok" at the annoying popup while I used another finger to tap something at the screen as soon as possible. Scrolling was like stuck motion this way... So I have been able to enter twrp and flash another rom.
Nonetheless I tested calling a person with the guest account (by allowing phone calls for guests via the same "tapping-technique"... took me aboout 10 minutes) and found out, there are exactly the same hissing /crackling problems with Android M than with Android L. So I will try Android Kitkat now. This bug is very common. Is there someone who can tell me a working solution? I am pretty sure my phone did not have this bug when I bought it with Kitkat OS installed. So a kitkat rom is my last hope right now.
regards,
Milan

Help! Can't flash ROMs from Flyme OS 5.1.1 system!

So there I was, using Cloudy 3.3 on my G2 international model (d802) when I thought to myself: Why wouldn't I change the ROM. I guess I got bored of it and while in the past year I tried almost EVERY ROM (at least every 5.1 lollipop ROM and these new marshmallow ROMs) I wanted something different this time. I remembered that Flyme OS system and wanted to give it a go. I found one here on xda site, I think it was Flyme 4.1 or 4.0 or something like that but I decided to go for a ,,newer" version of the system.
I found Flyme OS on this site: http://www.flyme.cn/firmwarelist-14.html
And as you can see the entire site is in Chinese but I managed somehow and downloaded it. I had TWRP 3.0 installed and I think I know the thing or two about flashing ROMs on this device. The whole installer is AROMA based and even though it was in Chinese I managed to flash the system. And that's when I knew I f****d up. After I installed it and it booted up, I figured that I'm not really into the whole Flyme interface and wanted to revert to stock. But I couldn't!
1. I no longer have download mode, when I stick USB cable and hold volume up it shows me an animation of ,,download mode'' but then in upper left corner appears a message saying ,,boot secure error'' or something like that and then it shows me a black screen.
2. I no longer have my TWRP recovery installed.
- I can't use 3rd party apps to restart my phone into recovery because this OS is NOT rooted! And I can't even root it because there's no method for it. I tried the default rooting method for MEIZU phones which include you logging in to your Flyme account and all of a sudden ,,root permissions'' option appears in your settings - DIDN'T HAPPEN. I also tried other different methods but to no avail. It just can't be rooted.​ - Even when I turn the phone off and try to do the hard reset thing with simultaneously holding power + volume down button - it won't show me the LG's default ,,factory reset'' screen which could potentially lead me into TWRP. It just boots normally!​
So, the conclusion:
I flashed an unknown Flyme OS system for LG G2 from a Chinese site and it works decently good but when it installed - it turned my G2 completely to a MEIZU phone. I have no clue on how to revert it and PLEASE I would appreciate any help given. Before giving your opinions in the comments, do read every sentence I wrote above.
Thanks in advanced.

duff105 said:
So there I was, using Cloudy 3.3 on my G2 international model (d802) when I thought to myself: Why wouldn't I change the ROM. I guess I got bored of it and while in the past year I tried almost EVERY ROM (at least every 5.1 lollipop ROM and these new marshmallow ROMs) I wanted something different this time. I remembered that Flyme OS system and wanted to give it a go. I found one here on xda site, I think it was Flyme 4.1 or 4.0 or something like that but I decided to go for a ,,newer" version of the system.
I found Flyme OS on this site: http://www.flyme.cn/firmwarelist-14.html
And as you can see the entire site is in Chinese but I managed somehow and downloaded it. I had TWRP 3.0 installed and I think I know the thing or two about flashing ROMs on this device. The whole installer is AROMA based and even though it was in Chinese I managed to flash the system. And that's when I knew I f****d up. After I installed it and it booted up, I figured that I'm not really into the whole Flyme interface and wanted to revert to stock. But I couldn't!
1. I no longer have download mode, when I stick USB cable and hold volume up it shows me an animation of ,,download mode'' but then in upper left corner appears a message saying ,,boot secure error'' or something like that and then it shows me a black screen.
2. I no longer have my TWRP recovery installed.
- I can't use 3rd party apps to restart my phone into recovery because this OS is NOT rooted! And I can't even root it because there's no method for it. I tried the default rooting method for MEIZU phones which include you logging in to your Flyme account and all of a sudden ,,root permissions'' option appears in your settings - DIDN'T HAPPEN. I also tried other different methods but to no avail. It just can't be rooted.​ - Even when I turn the phone off and try to do the hard reset thing with simultaneously holding power + volume down button - it won't show me the LG's default ,,factory reset'' screen which could potentially lead me into TWRP. It just boots normally!​
So, the conclusion:
I flashed an unknown Flyme OS system for LG G2 from a Chinese site and it works decently good but when it installed - it turned my G2 completely to a MEIZU phone. I have no clue on how to revert it and PLEASE I would appreciate any help given. Before giving your opinions in the comments, do read every sentence I wrote above.
Thanks in advanced.
Click to expand...
Click to collapse
Bump.

C'mon guys, there has to be someone who could possibly try to help

duff105 said:
C'mon guys, there has to be someone who could possibly try to help
Click to expand...
Click to collapse
Did you tried going to recovery mode by completely shutting off your phone and then pressing volume down + power button simultaneously. If goes into recovery mode as you said you have no twrp installed. What does it shows and also what happens when you connect your phone to pc in recovery mode?.
P.S i recovered from a similar issue like you on my sprint g2

qasim799 said:
Did you tried going to recovery mode by completely shutting off your phone and then pressing volume down + power button simultaneously. If goes into recovery mode as you said you have no twrp installed. What does it shows and also what happens when you connect your phone to pc in recovery mode?.
P.S i recovered from a similar issue like you on my sprint g2
Click to expand...
Click to collapse
I tried going to recovery with my phone being completely shut down, however, it simply turns the phone on. No button combination gets me into recovery anymore. As if it simply vanished from my phone (the recovery, of course). It doesn't show the default ,,Factory data reset" option when I hold volume down + power button whilst turning the phone on. No options whatsoever. So I didn't even get the chance to connect it to the PC while in recovery, since there's no recovery installed on my phone.

duff105 said:
I tried going to recovery with my phone being completely shut down, however, it simply turns the phone on. No button combination gets me into recovery anymore. As if it simply vanished from my phone (the recovery, of course). It doesn't show the default ,,Factory data reset" option when I hold volume down + power button whilst turning the phone on. No options whatsoever. So I didn't even get the chance to connect it to the PC while in recovery, since there's no recovery installed on my phone.
Click to expand...
Click to collapse
install quick boot. and try to access to recovery. maybe it will help.
otherwise... kingroot ... if your phone is not rooted. google for autorec for your model phone. it will install the recovery again

Stuck in EMUI Update, Need Help!

Hi, I need help with my Huawei P10 Lite WAS-LX1. I have poor knowledge on firmware versions, updates etc. so I'll try to describe my problem in short bullets. Here is the development of the situation:
- My phone was in water for couple of seconds
- After I dried it out, the only way I managed to turn it on was using combination of PWR + VOL+ or VOL- not sure which one I used
- That combination got me to Huawei splash screen, and immediately after that to EMUI screen, apparently for update - the screen looks exactly like this - take. ms/iaGMk
- The phone can't get out of this state, it keeps turning itself on and on and trying to install this update, there is no way to turn the phone off, it's just in this loop
Now, what I've tried and results:
- I tried uploading an update (update.app in dload folder) that I found on this forum, to an SD card, and the result was that installaton got to 5% and got to this screen again - take. ms/iaGMk
- I tried connecting the phone to my PC via USB, and the result was that installation got to 5%, and at that point my HiSuite asked me to authorize PC on the phone, looks like this - take. ms/VFUXt ,which I can't do because the phone is in this, recovery or whatever it's called, state
Now, at one point, the battery got empty and the phone somehow showed me the recovery menu, where I had among other options: Update with WiFi and Factory Reset. I did factory reset, and then I updated EMUI with WiFi - once it was done, the phone started up in safe mode, and everything was working except power/lock and volume buttons (is this normal for Android safe mode?).
I was checking the phone a bit and then it turned off, and now it's in the frickin loop again - take. ms/iaGMk
I can't do anything at all, it responds to nothing. My thinking is that there is maybe a correct version that I can upload to an SD card and perhaps that will be the solution.
Anyhow, that's basically it, please let me know if you have any questions. Keep in mind that I have no idea which firmware version it is because I can't start up the phone or anything.
Thanks a lot in advance!
Best,
Strahinja

StrahinjaS said:
Hi, I need help with my Huawei P10 Lite WAS-LX1. I have poor knowledge on firmware versions, updates etc. so I'll try to describe my problem in short bullets. Here is the development of the situation:
- My phone was in water for couple of seconds
- After I dried it out, the only way I managed to turn it on was using combination of PWR + VOL+ or VOL- not sure which one I used
- That combination got me to Huawei splash screen, and immediately after that to EMUI screen, apparently for update - the screen looks exactly like this - take. ms/iaGMk
- The phone can't get out of this state, it keeps turning itself on and on and trying to install this update, there is no way to turn the phone off, it's just in this loop
Now, what I've tried and results:
- I tried uploading an update (update.app in dload folder) that I found on this forum, to an SD card, and the result was that installaton got to 5% and got to this screen again - take. ms/iaGMk
- I tried connecting the phone to my PC via USB, and the result was that installation got to 5%, and at that point my HiSuite asked me to authorize PC on the phone, looks like this - take. ms/VFUXt ,which I can't do because the phone is in this, recovery or whatever it's called, state
Now, at one point, the battery got empty and the phone somehow showed me the recovery menu, where I had among other options: Update with WiFi and Factory Reset. I did factory reset, and then I updated EMUI with WiFi - once it was done, the phone started up in safe mode, and everything was working except power/lock and volume buttons (is this normal for Android safe mode?).
I was checking the phone a bit and then it turned off, and now it's in the frickin loop again - take. ms/iaGMk
I can't do anything at all, it responds to nothing. My thinking is that there is maybe a correct version that I can upload to an SD card and perhaps that will be the solution.
Anyhow, that's basically it, please let me know if you have any questions. Keep in mind that I have no idea which firmware version it is because I can't start up the phone or anything.
Thanks a lot in advance!
Best,
Strahinja
Click to expand...
Click to collapse
4gb or 3gb ram, dual or single sim?

nemanjsb said:
4gb or 3gb ram, dual or single sim?
Click to expand...
Click to collapse
Hi, I believe it's 3gb. It's a single sim device.