How to pull off left pins on motherbord - ZenFone 2 General

Hi.zenphone 2 32 g.the cable port of sim is broke into motherbord.there are afew "teeth" left there.how do i pull them of from the connector motherbord? Thanks

Use the force.

Posting a picture would help us a lot.
Use mechanical sense.

lift the back of the tab the flex cable goes in, if its the small one
Have to take the heat sinks off, metal over the board.
Dont worry, little grooves they go back in

Related

Bottom Connector Loose

The Cradle ConnectioN 0n The Bottom of the Phone is loose and it looks like it will break And am unable to sync and charge . i can only charge the device only when it tilt it foward whilst its connected to the cradle and it causes usb to say unrecorgnized device error can anyone tell me what to do
take it apart and solder it yourself ,if it is like mine it will be the two connectors on the left and right that have broken free ,on the outer casing. Just make sure that none of the metal pins are bent upwards,if they are just place something flat over the top of them and bend them straight again also make sure that its nice and flush with the connectors (you will need a magnifying glass, if you are as old and blind as me) then try and see if it works.
It worked for me
get the service manual to show you how to disassemble and reassemble the device here http://xdafiles.100webspace.net/513849

help pls, phone not charging ( not battery point)do i take phone apart?

need help please people.
my phone hasnt been charging properly for a few days now, to get it charging now i have to get one of my missis hair bands and wrap it round my phone and then round the usb cable so it stays in , although today it doesnt want to charge at all now .
ive noticed that the connection in the phone is loose and you can move it round a litle bit,
now the bit i need help with , is do i take the phone apart and try to fix it.?. im thinking of doing this but unsure about taking phone apart ( dont think my phone is under warrenty anymore,) and im guessing the usb connection on the phone is fixed onto a board.
is it worth me trying that or should i just take it to a repair shop ?
take a dry toothbrush, give the usb port a good scrub. dirt often builds up in the bottom of the port and stops the usb plug pushing deep enough to get a good contact.
Have a good inspect of the usb port, bright light and magnifier is good, see if you can see buildup, or a bent connector, or somesuch.
Also look at the usb plug on the cable, its uncommon but not unknown for the metal outer enclosure to open slightly, and make for a weak contact.
Sometimes a cable simply doesn't fit well for no obvious reason, , i have a generic cheap ebay cable that will only work when angled up or down, like yours, but looks perfectly fine, and feels to fit the socket, while the HTC cable works perfectly, so i know its not the port.
If it all looks good, then chances are you have a dodgy connection from the usb port to the mainboard, which will get worse every time you wiggle and bend the cable to get it to work. In this case, you COULD try a repair, but there have been reports on here of some repair shops pronouncing it too fiddly to replace teh usb port, and a new mainboard would be the only other option.
edit - just reread your post and seen that you can wiggle the port. Broken solder, gotta be. Its not an easy solder, so if your a dab hand, then go for it, if not, see above.
Hi iainbp, heresandyboy had this same trouble in http://forum.xda-developers.com/showthread.php?t=903977 from post 16.
It looks tricky!
Just a thought though, I recently bought a cheap phone charger with multiple interchangeable heads for different phones. The microUSB one became difficult to charge with and it took me a while to realise that the metal bit at the end had detached from its plastic casing, and when I plugged it into the phone it just got pushed back into the casing. (got my money back)
Possible with yours?

Replacement for HTC incredible PCB Connector

A few month's ago I'd ordered a LCD screen replacement for my incredible, and so when I got back from work o immediately took out the LCD from the package and started taking out my old broken. For me it was my first time experience replacing an LCD phone screen, anyways back to what I was going to say was when I unplugged the connector for the screen and the motherboard itself, after attempt to plug the connectors back together; the display connector plugged in perfect while the connector for the motherboard didn't do so well. The white piece that covers the PCB Connector, it tears a little bit off and I'd tried to power on the phone, meanwhile it didn't I tried again and things got worst. So I search online for a PCB Connector and see one, so I decided to and try to rip off the PCB Connector and plan to order the PCB Connector. So the part to attempt ripping off the PCB Connector didn't go so well, and stop there before things got worst. Any suggestions how I can replace that? I can't just leave my phone in my room and have to cover in dust. I need my phone back, how can I fix these? I know this thread seems long but I tries but it details for you guys.

MicroUsb socket broken a direct wiring fix working for old phones.

Attention do this at our own risk as it may damage our phone.
My used samsung galaxy pocket-neo was becoming impossible to charge causing me to break the adapter cables with constant wiggling and balancing acts to get it to work. I took it apart and the micro usb socket looked like an extremely difficult soldering job to replace.
The solution I am using for more than a month with no adverse effects is to cut the plug off and strip the 2 power wires at one end of an old usb cable. There are 4 different coloured wires, red, black, green and white. The green and white wires transmit data, whilst the red and black are the power lines. Red is positive, Black is negative. The sleeve of the cable has a metal mesh which is not necessary for my purposes so I electrical taped it back onto the cable.
The next step is to remove the battery of the phone: I have only done this on phones with removeable batteries. The ones I have used have three terminals; one is plus and one minus, the middle one is for a thermistor in the internal of the battery so that it doesn't overheat. Check the plus and minus with a tester to be sure and look at the way it mounts into the phone. The corresponding terminals in the phone are where I connect the wires.
Now here is the complicated part, - or negative(black) goes to the one negative copper pin in the back of the phone. The positive +(red) wire however needs to bridge the other two pins for reasons that I would like to find out. The white and green wire got taped up seperately to avoid short circuits and I replaced the battery to hold the wires firmly in place and closed the back of the phone. Plug the phone into a charger or external power pack (DC 5v) and it will work fine with no overheating, I suggest this be monitored for a while as it may vary with other hardware.
There may be better ways to do this, as far as I can tell in my case I am not actually charging the battery, instead the phone is running directly from the external power source. The strange thing is that the software(CM11) battery icon slowly discharges and after about 10 hours tells me I need to charge the battery but never turns off and when I restart it is immediately back up to full.
I have tested with a normal cable and the micro usb is still working even though it is still only working when I constantly wiggle the cable, I have cleaned it and as far as I can see its not going to ever work properly.
It would be good to know why the battery does not chargewhen using this method. I imagine it has to do with the internal workings of the phone that control the charging, discharging and battery temperature.
Making the old hardware live longer.
Replacing the micro usb is doable with a hot air gun a pair of tweezers, a clunky spring loaded solder sucker, a flux pen and two pairs of 3.5 x magnification reading glasses. You dont need any fancy rework station or microscope, assuming you have steady hands, reasonably good eyesight, and some soldering experience. I just tried this myself yesterday and fixed and Ace 3 and two S3 mini boards from my junk pile, and while it was a little tricky, it didn't require any brain surgery skills, just care, patience and some previous smd soldering experience.
Proceed as follows, mask off all of the surrounding components with kapton tape, apply lots of flux from your flux pen, then heat the plug carefully, pointing the hot air across the plug and away from the rest of the board. Grab the (hot) metal can of the USB plug with the tweezers, and gently lift it. Only remove the plug when all the solder is melted, and it feels loose, to avoid pulling off any tracks. Remove those tracks, and the phone is for the bin. Next, clear any holes that are required to mount the new plug, take care at this stage, as it is imperative that the replacement plug sits flush on the board otherwise the pins on the plug, wont touch the pads on the board, and worse still, you wont get the case back on at the end of the process.
To fit the new socket, clean the pads... no really clean them.... now make sure they are clean, and then flux them and tin them. Fit the new plug, and check that it sits flush to the board. Tack down one metal lug only on the can of the new plug. Check again that the pins are lined up, and carefully drag solder them. Check for shorts. Check again... clean the pads and check again. If you are happy, tack down the remaining three lugs, make sure they are flush and that there are no blobs of solder on the tops of them. Clean the board again. Test... Profit
Total time including additional swearing, re-cleaning... re-re-cleaning and re-fitting.. about 30 minutes and two strong coffees.
The replacement USB plugs are readily available on ebay typically around the £2 ($3) mark, but there are several different styles, and they are different, so make sure you use the correct one for your board.
Now back to your question... why does your battery not charge when you tack the wires to it... simple... it is trying its best not to explode. The USB port provides 5V, but the battery needs between 2.8 and 4.2 vots.. depending on its current state of charge, and this is what the charge controller chip within the phone provides. Anything else and the protection circuit kicks in.
I suggest if you don't fancy repairing the USB plug yourself, you get one of those cheap "universal" usb phone chargers from China, they cost about the same as the replacement USB plug, but are (marginally) less likely to blow up your battery.
itsthatidiotagain said:
Now back to your question... why does your battery not charge when you tack the wires to it... simple... it is trying its best not to explode. The USB port provides 5V, but the battery needs between 2.8 and 4.2 vots.. depending on its current state of charge, and this is what the charge controller chip within the phone provides. Anything else and the protection circuit kicks in.
I suggest if you don't fancy repairing the USB plug yourself, you get one of those cheap "universal" usb phone chargers from China, they cost about the same as the replacement USB plug, but are (marginally) less likely to blow up your battery.
Click to expand...
Click to collapse
Good description of the soldering job, the samsung pocket neo is very small but I look forward to having a go at fixing it properly one day, I dont yet have a magnifying glass or solder sucker, but I want to get them. Without these tools the job would be near impossible.
Little update: the phone is charging, I have disconected it and it holds its charge nicely, the internal software just doesn't register the trickle charge it is recieving, I have loads of old chargers and new usb cables and my old second hand phones micro usb port is way too damaged to work anymore with any charger. I use it as a modem principally, so it is connected every day and providing wifi to multiple devices and has no problems with over heating. Now nearly two months have passed and it works fine. Using this method it is possible to completely remove the battery as well. The phone is running directly off the 5 volt power with no ill effects.
It would be convienient to connect it directly to a pc in usb debug mode occasionally, and this is a very good reason for eventually fixing the usb plug.:good:

Circuit diagram of main board

Does anyone have a circuit diagram of an Umi Super main board? I am especially interested to know just what purpose the three flexible connections in the uper right corner on the board serve. They obviously make contact with opposite side of the phone case when it's assembled. There are also three at the top left corner of the board as well. After droping the phone, the two connectors at the very top on both sides broke off. The result was that the battery was quickly drained and no longer could be charged.
I managed mount them back on so that they also had functioning contacts by carefully super glueing them in place. After reasembling the phone it worked again but only for two days, then again I couldn't charge the phone. It turned out, that the connector on the right top corner had broken off again.
So just what is it for, anyway, because as far as I can tell, really only the second connector has a connection to metal on the cover when assembled?
So now I very, very carefully sodered it together and I knew I could destroy the rest of the electronics, but had nothing to loose... Then I tested the connection with a ohm meter and it was as it should be. Again I reassembled the phone, but still can't charge its battery. Maybe I really did kill something else in the process.
Still I am interested in a circuit diagram to understand what might be the problem. Can anyone help out?

Categories

Resources