desperate for some help with a sm-900f - Galaxy S 5 Q&A, Help & Troubleshooting

Hi,
I wouldnt say im a complete novice, i've rooted lots of devices without a hitch in the past. But after a day of trying I have to concede now that I am not as good as i thought. I can't load a rom onto my already (well was) rooted galaxy s5. It seemed a simple task, I downloaded the Marshmallow rom from sammobile for my right carrier, region etc I wanted to upgrade lollipop i had on it. Unfortunately it kept failing in odin 11. Made sure I copied the file to AP etc but wouldn't load.
Long story short I did manage to load a custom rom Galaxy S5 CM14 (CyanogenMod 14, Nougat ROM but I couldn't really get on with it so attempted to reinstall the official rom. I did also load twerp which I cant do and now with a firmware called philztouch which is the only thing I can seem to flash now. Unfortunately everytime I go into download mode and attempt a rom install it doesnt work.
This is what it is outputting attempting the official marshmallow rom below.... Any help much appreciated.
:crying:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900FXXU1CPFA_G900FEVR1CPF1_G900FXXU1CPE6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Removed!!
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1

fatfei said:
Hi,
I wouldnt say im a complete novice, i've rooted lots of devices without a hitch in the past. But after a day of trying I have to concede now that I am not as good as i thought. I can't load a rom onto my already (well was) rooted galaxy s5. It seemed a simple task, I downloaded the Marshmallow rom from sammobile for my right carrier, region etc I wanted to upgrade lollipop i had on it. Unfortunately it kept failing in odin 11. Made sure I copied the file to AP etc but wouldn't load.
Long story short I did manage to load a custom rom Galaxy S5 CM14 (CyanogenMod 14, Nougat ROM but I couldn't really get on with it so attempted to reinstall the official rom. I did also load twerp which I cant do and now with a firmware called philztouch which is the only thing I can seem to flash now. Unfortunately everytime I go into download mode and attempt a rom install it doesnt work.
This is what it is outputting attempting the official marshmallow rom below.... Any help much appreciated.
:crying:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900FXXU1CPFA_G900FEVR1CPF1_G900FXXU1CPE6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Removed!!
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1
Click to expand...
Click to collapse
Just an update, i have loaded twrp on there but too scared to touch anything else pending help

Hi try this guide find a g900f pit file or if you have made a backup of your own and flash it via odin then try again to flash stock
Url : forum.xda-developers.com/showthread.php?t=2659635

Unfortunately I now get this error on Odin
D:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin engine v(ID:3.1205)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Set PIT file..
<ID:0/010> DO NOT TURN OFF TARGET!!
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> SingleDownload.
<ID:0/010> aboot.mbn
<ID:0/010> sbl1.mbn
<ID:0/010> rpm.mbn
<ID:0/010> tz.mbn
<ID:0/010> sdi.mbn
<ID:0/010> NON-HLOS.bin
<ID:0/010> boot.img
<ID:0/010> recovery.img
<ID:0/010> system.img.ext4
<ID:0/010> modem.bin
<ID:0/010> cache.img.ext4
<ID:0/010> hidden.img.ext4
<ID:0/010> FAIL! (Size)
<ID:0/010>
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

force alarm, i was just being impatient. all working. Thank you very much for the help

No problem mate ?

Related

Softbricked my GS4 (i337m), any help would be appreciated!

Hey everyone,
I believe I just softbricked my phone, I tried to restore it back to stock via ODIN but it wont work,
Here is the error message from ODIN
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337MVLUAMDJ_I337MOYAAMDJ_I337MVLUAMDJ_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> recovery.img
<ID:0/003> persdata.img.ext4
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And it stuck on the screen that shows "firmware upgrade encountered an issue please select recovery mode in kies and try again"
WHAT DO I DO? :crying::crying::crying::crying::crying::crying:
Try flashing this http://forum.xda-developers.com/showthread.php?p=46943588 via Odin forI337MF3......cuz the one u used is for I337MDL ....
Swyped from BlueICESense_JBE
take a look at Jamison's guide just to see if you did some steps wrong
it is mdl so don't use the fw but the steps may be similar
http://www.infamousdevelopment.com/index.php?topic=115.msg890#msg890)*

N900V ODIN AUTH Fail.

I got an unlocked note 3 that I have been tring to add a recovery to or upgrade to LP. No matter what file I load in to either 3.07 or 3.09, I keep getting an auth fail. Am I missing something stupid here or is there something I forgot to do when I set odin up?
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.08.9-hltevzw.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Download firmware again .
I have tried that. I have also tried 4 different ver's of odin. I have downloaded the file like 5 times at this point and every time its the same thing. My phone will also display secure check fail :aboot

Help with Custom Binary Blocked by FRP lock

How do i repair this custom binary blocked FRP lock?
It started when i tried to install the lucky patcher app, i accidentally turned off my OEM debugging(i think) after i rooted my phone. I think it would not be necessary for me to turn it on since i have already rooted my phone. Then after i installed the lucky patcher it say that something about booting the device then the Custom Binary Blocked by FRP lock showed up and got stuck in prompt message for samsung s6 edge+
i tried to use the root again my phone but end up stuck agian, which apparently did nothing and might trip the system of my phone. I search tons of solutions on the internet, but mostly is to flash my ROM in odin. I have downloaded the files for the firmware which is 1.8gb, and ofcourse followed the procedure to plug my device and use AP(my firmware that i just downloaded)
and this always shows up:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G9287CDXS2BPE1_G9287COLB2BPB4_G9287CDXU2BPB4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
now i dont know what to do, it always fails to flash my device.. im so freaked out :crying::crying:
anyone please help
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G9287CDXS2BPE1_G9287COLB2BPB4_G9287CDXU2BPB4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img
<ID:0/003> cm.bin
<ID:0/003> hidden.img
<ID:0/003> modem.bin
<ID:0/003> recovery.img
<ID:0/003> sboot.bin
<ID:0/003> system.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
finally , WTF ! why could you MAAAAN ..
it happens just a miracle LOL ! please close the thread .. im done and fixed it
How did you fix it?
I have the same problem preventng phone from booting.

Cricket sgh-i337z custom recovery error

My device is already rooted from Kingoroot which worked easily and had no problems.
Now I'm trying to install custom recovery, I downloaded the newest IMG that TWRP has for my device, convert it to tar.md5, then I boot my phone into download mode and try to push the rom to my phone via Odin, and after about 3-4 seconds it says fail at the top, here is the output the Odin gives:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> twrp-2.8.4.0-jfltecri.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> twrp-2.8.4.0-jfltecri.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
It doesn't cause any errors or anything on my phone when it fails, I just restart my phone and it works just fine.
Thanks for the help, I couldn't find a similar error to mine with a solution posted previously for my device.
Try using different USB cables and USB ports.
OP resolved the issue. Thread closed.

[NEED HELP] Soft bricked Galaxy A5 2017

Need help i get soft bricked my samsung a5 2017 (LDU)
i brought LDU & installed A520FXXU2BQIH_A520FOJV2BQJ1_PAK from sammobile after installation phone sticked into GOOGLE FRP after 2-3 hours searching on youtube i found a method for google frp reset by COMBINATION file so i installed this file COMBINATION_FAC_FA60_A520FXXU3ARA3 in that 7.0 firmware A520FXXU2BQIH_A520FOJV2BQJ1_PAK now device get bricked also then i try more options too then i download
A520FXXU4BRA8_A520FOXA3BQL2_XEF & COMBINATION_FAC_FA60_A520FXXU4ARA4 still fail at wright system in odin also get back to 1st installed 7.0 firmware now get red error on device screen SW REV. CHECK FAIL. DEVICE: 4 BINARY:3
kindly help
Is your problem fixed or not.... If not the problem is with you binary.. You have to have one.. Your best and easiest way to solve your problem is to start all over again and flash your stock rom back and then root your phone.
Don't forget to backup your phone
thank you a lots for reply bro i did same what you said about me but all fail again take a look im not geek to understand kindly give me step by step solution.
with combination file in AP
COMBINATION_FAC_FA60_A520FXXU3ARA3_FAC3ARA3_CL12800524_QB16363926_REV00_user_mid_noship
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 1509 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
AND WITH FULL FIRMWARE
AP_A520FXXU3BQLA_CL12637612_QB16162045_REV00_user_low_ship_meta
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 4624 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
ALL FAIL DEVICE TILL THE SAME KINDLY HELP
Single file
download and load single file firmwares of the country
ozkanasilioglu said:
download and load single file firmwares of the country
Click to expand...
Click to collapse
single file not available on sammobile.com
now what to do sir
How do u find the firmware and can I use any version as long as its the country firmware

Categories

Resources