Related
I have a D802 Hong Kong version. In the secret menu (3845#*802#) i have found this: LGD802AT-00-V10C-HKG-XX-NOV-30-2013
Now, I would like to use the 4g connection in my country (Italy, carrier TIM) but the 4g option is not avaible in "network mode". After a test with another G2 (italian version and same carrier), I can say that the connection don't switch automatically on 4g but keeps the H+ one. So i think is necessary a modification.
Solutions?
Is it necessary to flash an europe radio? or something else? I'd like to keep the stock rom Lg but is not a fundamental.
Baseband: M8974A - AAAANAZM - 1.0.190036
Kernel: 3.4.0
Build: JDQ39B
I have the g2 for two days. I know it very little. I do not have much knowledge about it. Some good soul can explain to me how to do?
I need your help!
Did you verify that the device has the correct radio bands for the lte on that carrier?
x714x said:
Did you verify that the device has the correct radio bands for the lte on that carrier?
Click to expand...
Click to collapse
I don't know how to check! On the box of g2: gsm 850/900/1800/1900; wcdma 850/900/1900/2100; LTE 2100(B1)/1800(B3)/2600(B7)/900(B8)/800(B20).
My carrier is Tim but i don't kwow which band uses.
In secret menu/LTE Band section: avaible band 1,2,3,4,5,7,8,17,20,40. No one is selected.
Can i flash V10E firmware for Italy on V10C firmware for honk kong (actually on my device)?
Flashing different firmware wont help. Its either your apn is wrong or you didnt enable lte correctly. I checked and TIM uses 1800 (band 3) lte which your phone should work with.
x714x said:
Flashing different firmware wont help. Its either your apn is wrong or you didnt enable lte correctly. I checked and TIM uses 1800 (band 3) lte which your phone should work with.
Click to expand...
Click to collapse
maybe i should enable "band 3" in LTE setting in secret menu.
Hi,
I've a similar question and I hope someone could help me: I've a G2 phone using the D80210e-ESA-XX firmware.
In the product specifications, supported LTE frequency bands are 900/1800/2100/2600/850. I know that in Italy working frequency bands are 800/1800/2600. Now, my phone does not support 800 MHz: do you think is possible to upload a different firmware (IT or EUR ones) on my phone? With one of these firmware, does the device will work at 800 MHz?
Thank you so much.
I also had the D802 with Korean firmware!
Even though the phone itself supports LTE the Korean firmware doesn't!
I flashed the EU version and everything worked fine afterwards!!!
zacharias99 said:
I also had the D802 with Korean firmware!
Even though the phone itself supports LTE the Korean firmware doesn't!
I flashed the EU version and everything worked fine afterwards!!!
Click to expand...
Click to collapse
Hi @zacharias99, are you using the LTE in Italy?
@sunshonic, I didn't understand if your LTE works in Italy using the secret menu. Is it working?
Thank you
madner81 said:
Hi @zacharias99, are you using the LTE in Italy?
@sunshonic, I didn't understand if your LTE works in Italy using the secret menu. Is it working?
Thank you
Click to expand...
Click to collapse
No no i am using the LTE in Greece!!!
But LTE is LOCKED in Korean firmware!!!
In older Korean Firmware you could activate LTE from secret menu but in newer version this option has been removed!
The only solution in my case was to flash a european (or in your case italian) Firmware and everything worked like it should
zacharias99 said:
I also had the D802 with Korean firmware!
Even though the phone itself supports LTE the Korean firmware doesn't!
I flashed the EU version and everything worked fine afterwards!!!
Click to expand...
Click to collapse
Same here, restored to stock eu/nordic. Using HK G2 in Norway. No issues with 4G now
Sent from my LG-D802 using Tapatalk
Does your country offer 4G networks? I'm in Kenya n any 4G device I ship in shows 4G even though we dont have it yet
Sent from my HTC One using XDA Premium 4 mobile app
popsi said:
Same here, restored to stock eu/nordic. Using HK G2 in Norway. No issues with 4G now
Click to expand...
Click to collapse
@popsi, @zacharias99 did you follow a specific procedure to upload the european firmware. I'm not so sure to perform it cause some month ago I've bricked an old Motorola (I don't remember the exact model) using simply a firmware of a different country. The result was a brick cause two firmware did not use the same way to allocate the memory...
madner81 said:
@popsi, @zacharias99 did you follow a specific procedure to upload the european firmware. I'm not so sure to perform it cause some month ago I've bricked an old Motorola (I don't remember the exact model) using simply a firmware of a different country. The result was a brick cause two firmware did not use the same way to allocate the memory...
Click to expand...
Click to collapse
My friend i don't really know where in this forum the instructions for flashing a new stock firmware are... (I am also new in this community)
And i flashed it with Greek instructions so my link won't help you and i don't want to post some link i haven't tested by myself...
Sorry i hope you can understand!
At moment i have no time, but if I would be you I would search in the G2 Section for instructions!
They must definitely be somewhere!
Did you subscribe for LTE with your carrier?
Sent from my LG-D802 using Tapatalk
zacharias99 said:
I also had the D802 with Korean firmware!
Even though the phone itself supports LTE the Korean firmware doesn't!
I flashed the EU version and everything worked fine afterwards!!!
Click to expand...
Click to collapse
@zacharias99, I've checked that 4G can be enabled using the secret menu
1. Go to LTE-Only
2. Modem Settings
3. RAT Selection
4. Select GSM / WCDMA / LTE auto
as in the post http://forum.xda-developers.com/showthread.php?t=2494751
At the moment it doesn't seem to work for me, probably because my sim still has not been enabled for 4g.
Have you ever enabled this option (with the previous korean firmware, I mean)?
@zacharias99, @popsi: the new european firmware allows to navigate over the 800MHz frequency band for you?
Thank you
madner81 said:
@zacharias99, I've checked that 4G can be enabled using the secret menu
1. Go to LTE-Only
2. Modem Settings
3. RAT Selection
4. Select GSM / WCDMA / LTE auto
as in the post http://forum.xda-developers.com/showthread.php?t=2494751
At the moment it doesn't seem to work for me, probably because my sim still has not been enabled for 4g.
Have you ever enabled this option (with the previous korean firmware, I mean)?
@zacharias99, @popsi: the new european firmware allows to navigate over the 800MHz frequency band for you?
Thank you
Click to expand...
Click to collapse
Hi,
the procedure using the secret menu definitively works on my D80210e-ESA-XX, but I need to re-select it after every reboot.
Does anybody know how to make it permanent or how to automate this selection on boot (maybe using Tasker or something similar)?
zacharias99 said:
No no i am using the LTE in Greece!!!
But LTE is LOCKED in Korean firmware!!!
In older Korean Firmware you could activate LTE from secret menu but in newer version this option has been removed!
The only solution in my case was to flash a european (or in your case italian) Firmware and everything worked like it should
Click to expand...
Click to collapse
by flash, did you mean flash kdz of different region?
gpkumaran said:
by flash, did you mean flash kdz of different region?
Click to expand...
Click to collapse
yes exactly!
I flashed the European .kdz file!
I have an international G2 D802.. We, in india have certain operators in Band 40 LTE.. Is it possible to activate Band 40 in D802 by flashing D802T kdz in D802??? Kindly Help..
Recently with the delay on 5.0 for the US LTE variant, because of AT&T, I have lost my patience with them. I am looking for a way to rid myself of this BS while maintaining full stock software. I have heard that the variants of the tablet are actually not different, and the firmwares may work on either model. Has anyone tried this? I'm well aware the cell bands supported may change (but my carrier only requires one band, and the WW variant supports one of my carrier's bands). I would love to know if it works, and if I can dirty flash the package to keep my data, since the rom is basically identical.
I flashed OTA posted in general forum for LTE and using it in ATT. Unlocked bootloader, CWM, and root afterwards. I'm not quite sure what you're looking for?
Sent from my SHIELD Tablet using XDA Premium HD app
http://forum.xda-developers.com/showthread.php?t=2945023
shannoncole05 said:
I flashed OTA posted in general forum for LTE and using it in ATT. Unlocked bootloader, CWM, and root afterwards. I'm not quite sure what you're looking for?
Sent from my SHIELD Tablet using XDA Premium HD app
Click to expand...
Click to collapse
Bricks.
No what i'm asking is if i could convert my device to the WW variant with a firmware flash, and thus avoid needing to manually flash OTA files becauze of delays. I know this isn't going to be the last update delayed on the US variant so i'm wondering if i can just switch the installed software from the US LTE version to the WW LTE version, without bricking.
Yeah.. I am thinking the same thing as well.
If it was possible without bricking the device, I would love to flash the "Rest of the World" firmware on the AT&T set too.
xonix240719mu said:
Yeah.. I am thinking the same thing as well.
If it was possible without bricking the device, I would love to flash the "Rest of the World" firmware on the AT&T set too.
Click to expand...
Click to collapse
You're welcome to try it with the factory images. If it does brick, you can always restore through the same process. I plan on attempting it soon, but i am waiting on a microsd card.
Nintonito said:
Recently with the delay on 5.0 for the US LTE variant, because of AT&T, I have lost my patience with them. I am looking for a way to rid myself of this BS while maintaining full stock software. I have heard that the variants of the tablet are actually not different, and the firmwares may work on either model. Has anyone tried this? I'm well aware the cell bands supported may change (but my carrier only requires one band, and the WW variant supports one of my carrier's bands). I would love to know if it works, and if I can dirty flash the package to keep my data, since the rom is basically identical.
Click to expand...
Click to collapse
Theoretically, the only thing that would be changed between builds is the GSM stack. However the OTA between the WW and the US version would not work by default. You'd need to go into the OTA zip and mess around with some of the build.prop info. Which then may cause MD5 mismatches when it is parsed, and would definitely affect subsequent OTA updates because of MD5 mismatches.
If there are Android 5.0 factory images available for the WW ROM you feel would be suitable for your geography, then this would be the safer way to proceed.
I remember when I owned a Samsung Galaxy S2, there was an XDA thread with flashable modems you could push to your device to get better reception in your area. Essentially the differences between the WW and US/CAN versions should only be the GSM stack, and perhaps some carrier-specific bundled app (like the AT&T app for example).
Just a quick update for those who are interested:
Well ... I just did it. Successfully flashed the RoW recovery image on the Shield Tablet LTE set which I purchased from US via Ebay. I'm still in the process of restoring but so far everything seems to be working fine.
Confirmed 2 things during the flashing of recovery image,
Quote:
1) Issues of Cellular/Sim Card on the US LTE set is almost certainly Lollipop firmware related. No problems on FW 4.4.2
2) Problem of Wi-Fi authentication error after sharing files via Super Beam ( Wi-Fi direct ) is also resolved after revert to 4.4.2
I think I will be sticking with 4.4.2 for now with the added bonus of file managers working on Kit Kat.
xonix240719mu said:
Just a quick update for those who are interested:
Well ... I just did it. Successfully flashed the RoW recovery image on the Shield Tablet LTE set which I purchased from US via Ebay. I'm still in the process of restoring but so far everything seems to be working fine.
Confirmed 2 things during the flashing of recovery image,
Quote:
1) Issues of Cellular/Sim Card on the US LTE set is almost certainly Lollipop firmware related. No problems on FW 4.4.2
2) Problem of Wi-Fi authentication error after sharing files via Super Beam ( Wi-Fi direct ) is also resolved after revert to 4.4.2
I think I will be sticking with 4.4.2 for now with the added bonus of file managers working on Kit Kat.
Click to expand...
Click to collapse
Thanks for the update. I am interested in this also.
So i'm assuming from your post you got LTE working? Which country are you in? Where do you get the factory images from?
I live in Australia and have the US LTE version. HSPA+ is good but it would be nice to have LTE working on my network (Telstra).
perky nerky said:
Thanks for the update. I am interested in this also.
So i'm assuming from your post you got LTE working? Which country are you in? Where do you get the factory images from?
I live in Australia and have the US LTE version. HSPA+ is good but it would be nice to have LTE working on my network (Telstra).
Click to expand...
Click to collapse
Actually, I don't have a 4G LTE micro sim card with me so I can't verify that at the moment. I am trying to test it out using my friend's sim card and will report back with the results. In my opinion, it's not a good idea to be trying my nano sim on this.
I'm from Singapore and the network I'm on supports LTE Band 3 & 7 and my AT&T Moto X which supports Band 7 works out of the box.
Got them from Nvidia developers website but you have to register for a free account first.
xonix240719mu said:
Actually, I don't have a 4G LTE micro sim card with me so I can't verify that at the moment. I am trying to test it out using my friend's sim card and will report back with the results. In my opinion, it's not a good idea to be trying my nano sim on this.
I'm from Singapore and the network I'm on supports LTE Band 3 & 7 and my AT&T Moto X which supports Band 7 works out of the box.
Got them from Nvidia developers website but you have to register for a free account first.
Click to expand...
Click to collapse
Yep I need LTE band 3 for my network which is not supported out of the box by my US LTE shield. If your network supports LTE Band 7 then your shield should also be able to access your LTE network as BOTH the US and RoW LTE shields support LTE Band 7.
So I don't think your experiment will help me. Is there any way finding out which LTE Bands your shield supports now that you have flashed the RoW recovery image?
perky nerky said:
Yep I need LTE band 3 for my network which is not supported out of the box by my US LTE shield. If your network supports LTE Band 7 then your shield should also be able to access your LTE network as BOTH the US and RoW LTE shields support LTE Band 7.
So I don't think your experiment will help me. Is there any way finding out which LTE Bands your shield supports now that you have flashed the RoW recovery image?
Click to expand...
Click to collapse
I am not really an expert on such matters but let me try and if it's possible to find out the information you are looking for.
Why not try flashing it and give it a go ? There's the bonus perk of removing the AT&T app from the device.
xonix240719mu said:
I am not really an expert on such matters but let me try and if it's possible to find out the information you are looking for.
Why not try flashing it and give it a go ? There's the bonus perk of removing the AT&T app from the device.
Click to expand...
Click to collapse
Hi, I am currently using US LTE NVIDIA Shield Tablet in Singapore as well. I have successfully flashed the RoW recovery image to my tablet (since I'm downgrading from Lollipop as well, so I thought I might as well try), but I noticed that there is no baseband file in the recovery image package. I proceeded to flash anyway.
One thing I noticed after flashing is that I still am not getting LTE (half of Singapore is band 3, and my home is under its coverage). So, it's pretty safe to say that the baseband is not affected by the factory image.
However, it might also be that the latest recovery image doesn't cover the baseband, and it might be included in the previous updates. So, I'm trying to download the previous recovery images and see whether there are baseband images are there.
EDIT: baseband image is not in there. The baseband version is definitely still for North America (e1729-nala.4.05_0.6.3 @786934, notice the 'na' part?).
inscythe said:
Hi, I am currently using US LTE NVIDIA Shield Tablet in Singapore as well. I have successfully flashed the RoW recovery image to my tablet (since I'm downgrading from Lollipop as well, so I thought I might as well try), but I noticed that there is no baseband file in the recovery image package. I proceeded to flash anyway.
One thing I noticed after flashing is that I still am not getting LTE (half of Singapore is band 3, and my home is under its coverage). So, it's pretty safe to say that the baseband is not affected by the factory image.
However, it might also be that the latest recovery image doesn't cover the baseband, and it might be included in the previous updates. So, I'm trying to download the previous recovery images and see whether there are baseband images are there.
EDIT: baseband image is not in there. The baseband version is definitely still for North America (e1729-nala.4.05_0.6.3 @786934, notice the 'na' part?).
Click to expand...
Click to collapse
Sorry I don't really understand ... the RoW software cover for both Band 3 and 7 since the UK edition supports these LTE bands as specified in Nvidia FAQ.
You should still be able to get Band 7 coverage which the NA edition supports as well, right ?
Am I missing something ?
inscythe said:
Hi, I am currently using US LTE NVIDIA Shield Tablet in Singapore as well. I have successfully flashed the RoW recovery image to my tablet (since I'm downgrading from Lollipop as well, so I thought I might as well try), but I noticed that there is no baseband file in the recovery image package. I proceeded to flash anyway.
One thing I noticed after flashing is that I still am not getting LTE (half of Singapore is band 3, and my home is under its coverage). So, it's pretty safe to say that the baseband is not affected by the factory image.
However, it might also be that the latest recovery image doesn't cover the baseband, and it might be included in the previous updates. So, I'm trying to download the previous recovery images and see whether there are baseband images are there.
EDIT: baseband image is not in there. The baseband version is definitely still for North America (e1729-nala.4.05_0.6.3 @786934, notice the 'na' part?).
Click to expand...
Click to collapse
Thank you. That is exactly the information I was looking for. Unfortunately there is no point flashing the RoW recovery image if you wish to change your baseband (and then use different LTE bands like I want to).
Is there anywhere I can download the RoW baseband images? I remember they were readily available for my nexus 4.
xonix240719mu said:
Sorry I don't really understand ... the RoW software cover for both Band 3 and 7 since the UK edition supports these LTE bands as specified in Nvidia FAQ.
You should still be able to get Band 7 coverage which the NA edition supports as well, right ?
Am I missing something ?
Click to expand...
Click to collapse
As I said, the image doesn't include the baseband image. So, no matter what you flash on the rom side, it won't matter.
Also, about band coverage in Singapore, it's not a full overlap. Some areas are band 3 (south and west), while some band 7 (North and East). I know this from an M1 engineer friend. So, yeah, no LTE band 3 in this factory image here.
But not all hope is lost. If one day Nvidia decides to update baseband, it will then definitely include the baseband in the OTA or factory image. So, possibility of switching is still there.
Was there a baseband update with the latest software update (2.0)?
The factory images for 2.0 have still not been released.
In another strange twist when i turned on my tablet this morning I was surprised to see my US shield had LTE here in Australia. Which means only one thing - Telstra are expanding their LTE spectrum in my area!
perky nerky said:
Was there a baseband update with the latest software update (2.0)?
The factory images for 2.0 have still not been released.
In another strange twist when i turned on my tablet this morning I was surprised to see my US shield had LTE here in Australia. Which means only one thing - Telstra are expanding their LTE spectrum in my area!
Click to expand...
Click to collapse
I downloaded the OTA manually and checked the content. It doesn't have any baseband update. Also, just to confirm again, I actually re-installed Lollipop. The baseband is still unchanged (only the suffix @ part changed, but I think it's just some marker).
I checked wikipedia, and it seems that Telstra has band 3 and 28. There's a good chance that they switched your area's band to 3, or they simply add band 7 (the latter is, of course, ideal).
I read that Nvidia is preparing an update to the existing Lollipop system. Hopefully they will include a baseband update, then we can probably make the jump to the RoW ROM. For now, I'm sticking with the US ROM first.
inscythe said:
As I said, the image doesn't include the baseband image. So, no matter what you flash on the rom side, it won't matter.
Also, about band coverage in Singapore, it's not a full overlap. Some areas are band 3 (south and west), while some band 7 (North and East). I know this from an M1 engineer friend. So, yeah, no LTE band 3 in this factory image here.
But not all hope is lost. If one day Nvidia decides to update baseband, it will then definitely include the baseband in the OTA or factory image. So, possibility of switching is still there.
Click to expand...
Click to collapse
Okay ... I see that you are not able to get Band 3 coverage. But just to confirm, you are still able to get band 7 4G LTE coverage on the ROW Rom right ?
My phone 4G LTE is on Singtel, getting pretty good coverage island wide on Band 7. Unfortunately, it's a nano sim and I'm hesitant to test it on the tablet in case in gets jammed inside the slot.
So long everything works fine, I'm sticking with ROW Rom as it will probably not have none of the nonsense whereby it require AT&T approval before release.
Sorry to trouble you on another matter, I have reported this 2 issues to Nvidia customer support but just want to check if it's just my set or an common problem.
1) Cellular data connectivity will not return after enable aeroplane mode. SIM card is subsequently not detected.
2) After sharing files using Wi-Fi direct ( SuperBeam app ), Wi-Fi connection doesn't auto reconnect due to failed authentication. Require manual intervention.
What I can say is this 2 issues no longer occur once I downgraded the software from Android 5.0 back to Kit Kat 4.4.2
---------- Post added at 01:54 PM ---------- Previous post was at 01:46 PM ----------
perky nerky said:
Was there a baseband update with the latest software update (2.0)?
The factory images for 2.0 have still not been released.
In another strange twist when i turned on my tablet this morning I was surprised to see my US shield had LTE here in Australia. Which means only one thing - Telstra are expanding their LTE spectrum in my area!
Click to expand...
Click to collapse
According to Nvidia faq, the North American version that works on AT&T, T-Mobile and Rogers on LTE bands 2, 4, 5, 7, and 17 and HSPA bands 1, 2, 4, 5.
I see that this article ( http://www.cnet.com/au/news/telstra-expands-its-4g-services-including-the-700mhz-band-trials/ ) states that Telstra is conducting trials for 700mhz (Band 17) in your area. Maybe this is why you have begun receiving 4G LTE reception in your area ?
xonix240719mu said:
According to Nvidia faq, the North American version that works on AT&T, T-Mobile and Rogers on LTE bands 2, 4, 5, 7, and 17 and HSPA bands 1, 2, 4, 5.
I see that this article states that Telstra is conducting trials for 700mhz (Band 17) in your area. This is probably why you have begun receiving 4G LTE reception.
http://www.cnet.com/au/news/telstra-expands-its-4g-services-including-the-700mhz-band-trials/
Click to expand...
Click to collapse
I initially thought it may have been the planned 700mHz expansion by Telstra in my area HOWEVER Telstra's 700mHz expansion is actually Band 28 (not Band 17) and my US shield does not work on Band 28 out of the box. Although LTE Band 17 and 28 both use the 700mHz spectrum they both use different parts of that spectrum so are not compatible.
What I think has happened is there is some LTE Band 7 coverage in the middle of town here which is where I was when I got LTE coverage today. As I understand it Telstra has some limited LTE Band 7 coverage with most of the LTE network being Band 3........ so I'll still have to wait until I can flash a RoW baseband which will hopefully give me Band 3.....
Four things to note before proceeding...
1. This only works for users having vs985 model outside the US or not on verizon network.
2. I'm beginner im not responsible for any harm to your phone , I'm just sharing what i did to attain 4g services.
3. May be you already know all the things in the post but it can be useful for beginners like me .
4. Sorry for the english as its not my native language.
So Hi guys i installed this rom and as usually i was not getting any 4G or lte network.
Then i go to my network provider's website to check on which Band or frequency 4g services are active. ( for this i just googled 'idea 4g band' and i am redirected to my network provider's website. Here 'idea' is the name of network provider.)
So i found that in my region 4g services are active on Band3
Different careers use different Bands to provide 4g services such as band40 , band17 etc
Then i go to phone's hidden menu by the Advanced Menu of Fulmics Tweaks.
In hidden menu i select Modem Protocol > LTE Band Selection
There i select Band3 but i got "Fail' message on screen , however when i select band4 it gave me a 'success' message.
It means on my phone band4 is active but not band3.
All this information of Bands are stored in Modem or Bootstack section of our phone.
May be fulmics rom is having a band concerned with international rom So now i need a modem on which Band3 can be activated by going to hidden menu.
So i just flashed 35b Bootstack compiled by @xdabbeb.
Which can be found in this thread http://forum.xda-developers.com/verizon-lg-g3/development/xdabbeb-s-vs980-2-0-0-t3231279
After flashing when i tried to select band3 in hidden menu it gave a 'success' message . It means Band3 is activated on my phone. And now when i searched for all networks in Networks Menu of Phone Setting. I got my network listed and i successfully registered on it. And got 4G NETWORK.
So first of all you should know on which band your network is working and then try flashing different bootstacks on which your 4g Band can be activated.
Flashing wrong Bootstack can brick your phone
""Do not flash any bootstack above 35b. Custom roms are still not compatible with bootstacks above 35b""
You can try 24b , 12b. (But im sure only about 35b as i tried only this)
Again I'm not responsible for any harm to your phone. Use your mind and search thoroughly before taking any step.
akki7636 said:
Three things to note before proceeding...
1. I'm beginner im not responsible for any harm to your phone , I'm just sharing what i did to attain 4g services.
2. May be you already know all the things in the post but it can be useful for beginners like me .
3. Sorry for the english as its not my native language.
So Hi guys i installed this rom and as usually i was not getting any 4G or lte network.
Then i go to my network provider's website to check on which Band or frequency 4g services are active. ( for this i just googled 'idea 4g band' and i am redirected to my network provider's website. Here 'idea' is the name of network provider.)
So i found that in my region 4g services are active on Band3
Different careers use different Bands to provide 4g services such as band40 , band17 etc
Then i go to phone's hidden menu by the Advanced Menu of Fulmics Tweaks.
In hidden menu i select Modem Protocol > LTE Band Selection
There i select Band3 but i got "Fail' message on screen , however when i select band4 it gave me a 'success' message.
It means on my phone band4 is active but not band3.
All this information of Bands are stored in Modem or Bootstack section of our phone.
May be fulmics rom is having a band concerned with international rom So now i need a modem on which Band3 can be activated by going to hidden menu.
So i just flashed 35b Bootstack compiled by @xdabbeb.
Which can be found in this thread http://forum.xda-developers.com/verizon-lg-g3/development/xdabbeb-s-vs980-2-0-0-t3231279
After flashing when i tried to select band3 in hidden menu it gave a 'success' message . It means Band3 is activated on my phone. And now when i searched for all networks in Networks Menu of Phone Setting. I got my network listed and i successfully registered on it. And got 4G NETWORK.
So first of all you should know on which band your network is working and then try flashing different bootstacks on which your 4g Band can be activated.
Flashing wrong Bootstack can brick your phone
""Do not flash any bootstack above 35b. Custom roms are still not compatible with bootstacks above 35b""
You can try 24b , 12b. (But im sure only about 35b as i tried only this)
Again I'm not responsible for any harm to your phone. Use your mind and search thoroughly before taking any step.
Click to expand...
Click to collapse
Hi there, thanks for the info. What area are you in and where did you find what band you needed? I have tried numerous times with all the bootstacks and never had consistent 4G.
@mopartonyg
I'm in India and i just checked my career's website to know which band they are using. However in USA Verizon wireless uses Band12 as Primary Band and Band2 , Band4 as Secondary band to strengthen the signal in densely populated urban area. So if you are verizon user in USA band 12,4,2 must be activated. I can't say anything about consistency as it varies from place to place.
Actually Verizon uses band 13 for it's primary along with bands 4 and 2. Not having any luck getting data to work on Fulmics with this method. I select band 13 and band 4 (as band 2 is not in my area) yet even with that I still can't get data at all on Verizon with Fulmics.
same boat here... actually the only band I can get working is 4. I have to assume the design of the international rom with the band they are designed around, just don't play nice with our CDMA harware/modem partition. I would suspect that the international roms would require some engineering for them to really work properly. not sure if just porting them over and chaning settings is going to get the job done. perhaps someone more intelligent than I could share some light, but there certainly is a conflict with how these roms communicates across the CDMA bands in the US
Sent from my VS985 4G using XDA-Developers mobile app
@b00ster23@AngryManMLS
One thing i noticed here... that only Verizon sim users are facing problem regarding 4G whereas other international users like me ( and some of my friends in China are free to select any network ). So may be verizon is creating restrictions as when i was on Stock vs985 verizon Rom ( unrooted) , i was not getting any official ota updates. It always says your software is up to date. But then i found a statement in Verizon's website that you will not get any official updates if you are not having verizon sim.
So verizon knows what Rom and what sim we are using.
Sry 4 english
akki7636 said:
@b00ster23@AngryManMLS
One thing i noticed here... that only Verizon sim users are facing problem regarding 4G whereas other international users like me ( and some of my friends in China are free to select any network ). So may be verizon is creating restrictions as when i was on Stock vs985 verizon Rom ( unrooted) , i was not getting any official ota updates. It always says your software is up to date. But then i found a statement in Verizon's website that you will not get any official updates if you are not having verizon sim.
So verizon knows what Rom and what sim we are using.
Sry 4 english
Click to expand...
Click to collapse
I agree with this statement even i am getting 4G with Warid Telecom here in Pakistan.
SignatureBoy said:
I agree with this statement even i am getting 4G with Warid Telecom here in Pakistan.
Click to expand...
Click to collapse
Oh... Glad to hear that buddy..
So i think my post is useful for only international users which are not on verizon wireless.
akki7636 said:
@b00ster23@AngryManMLS
One thing i noticed here... that only Verizon sim users are facing problem regarding 4G whereas other international users like me ( and some of my friends in China are free to select any network ). So may be verizon is creating restrictions as when i was on Stock vs985 verizon Rom ( unrooted) , i was not getting any official ota updates. It always says your software is up to date. But then i found a statement in Verizon's website that you will not get any official updates if you are not having verizon sim.
So verizon knows what Rom and what sim we are using.
Sry 4 english
Click to expand...
Click to collapse
A couple of good approaches to the issue. Although it needs to be noted 4G is directly related to the band on each carrier (VZW, TMO, etc) See Below
Carrier 4G LTE Bands Frequencies
Verizon Wireless 2, 4, 13 1900, 1700 f, 700 c
T-Mobile 2, 4, 12 1900, 1700 def, 700 a
Sprint 25, 26, 41 1900 g, 850, 2500
Europe 3, 7, 20 1800, 2600, 800
If a specific ROM cannot be set to the correct bands above, it would make sense to me that Verizon wouldn't work in Europe on a stock VZW ROM. It would not be able to use the channels in Europe.
And vice versa, that Verizon wouldn't work in the states on an international ROM in the US. Whether the Verizon SIM is blocking that band, or the design of the ROM, would be a better question for the developers.
SignatureBoy said:
I agree with this statement even i am getting 4G with Warid Telecom here in Pakistan.
Click to expand...
Click to collapse
Warid's approved devices will definitely work with Warid's LTE network. For our "Warid LTE Approved' devices please visit the "Warid's LTE devices" section. You can also purchase LTE devices that support 1800 MHz (FDD-LTE Bands 3) from other sources. However, Warid doesn't take responsibility for these devices if they do not work on Warid's LTE network http://www.waridtel.com/lte/faqs
So it makes sense that if BAND 3 works international (see above) that you get 4G
The one thing I noticed after activating bands 13 and 4 (with the proper VS985 35B bootstack) in the hidden settings is when I searched for my network under network settings it does bring up Verizon but it fails authentication. So it's like there is something missing in Fulmics ROM itself that would get it to where the ROM will work with Verizon's network. So is it a matter of lifting whatever files from say 47A/47B into Fulmics that have the Verizon VS985 specific info to get it to work perhaps?
AngryManMLS said:
The one thing I noticed after activating bands 13 and 4 (with the proper VS985 35B bootstack) in the hidden settings is when I searched for my network under network settings it does bring up Verizon but it fails authentication. So it's like there is something missing in Fulmics ROM itself that would get it to where the ROM will work with Verizon's network. So is it a matter of lifting whatever files from say 47A/47B into Fulmics that have the Verizon VS985 specific info to get it to work perhaps?
Click to expand...
Click to collapse
I think now its not a matter of bootstack. Because even when Required Band is activated we can't register to the Verizon. Xpirt mentioned in a post that he is working to resolve network issues in Verizon models. We can hope that this problem will be solved in next version However xdabbeb shared that the 47A modem won't work without the corresponding 47A secondary bootloader (sbl1). Unfortunately, the 47A sbl1 doesn't play nice with the last bump-exploitable Android bootloader (aboot) we have from 12b. If you use that pairing, you'll put your device into 9008 bulk mode(Hard brick).
akki7636 said:
I think now its not a matter of bootstack. Because even when Required Band is activated we can't register to the Verizon. Xpirt mentioned in a post that he is working to resolve network issues in Verizon models. We can hope that this problem will be solved in next version However xdabbeb shared that the 47A modem won't work without the corresponding 47A secondary bootloader (sbl1). Unfortunately, the 47A sbl1 doesn't play nice with the last bump-exploitable Android bootloader (aboot) we have from 12b. If you use that pairing, you'll put your device into 9008 bulk mode(Hard brick).
Click to expand...
Click to collapse
The good news is we do have 47A ROMs that are using the 35B modem so there is potential that Xpirt could use that as a source for a fix with the authentication issue. So @xpirt if you need anyone to beta test fixes my VS985 is ready to help!
AngryManMLS said:
The good news is we do have 47A ROMs that are using the 35B modem so there is potential that Xpirt could use that as a source for a fix with the authentication issue. So @xpirt if you need anyone to beta test fixes my VS985 is ready to help!
Click to expand...
Click to collapse
+1
AngryManMLS said:
The good news is we do have 47A ROMs that are using the 35B modem so there is potential that Xpirt could use that as a source for a fix with the authentication issue. So @xpirt if you need anyone to beta test fixes my VS985 is ready to help!
Click to expand...
Click to collapse
This is good to hear and I second that!
Looking forward to getting it fixed and use it as my daily driver. It would totally be worth a big donation, thanks to everyone working on making this available to so many.
Great discussion towards the development of the International ROM's for our VS985. I was able to get 4G with Andy's 30A ported ROM...although the signal bars never came up on my phone, I was able to get the 4G speeds. I noticed that the APN XML was filled with Chinese... So for whatever reason and way, my phone was able to grab "somebody's" 4G tower. I'm hoping the RIL (Radio Interface Layer) and libraries were pulled over and perhaps this could provide some more insight to @Xspirit
b00ster23 said:
Great discussion towards the development of the International ROM's for our VS985. I was able to get 4G with Andy's 30A ported ROM...although the signal bars never came up on my phone, I was able to get the 4G speeds. I noticed that the APN XML was filled with Chinese... So for whatever reason and way, my phone was able to grab "somebody's" 4G tower. I'm hoping the RIL (Radio Interface Layer) and libraries were pulled over and perhaps this could provide some more insight to @Xspirit
Click to expand...
Click to collapse
Cool buddy... I think our vs985 will be on 4g Speed very soon.
akki7636 said:
Cool buddy... I think our vs985 will be on 4g Speed very soon.
Click to expand...
Click to collapse
I am on BlackSoulxxx latest LG G3 Tekcafe v5.3 D85530A-Full G5 ROM. Here's what I did to get the bars with 4g data. I tested it out in areas where there is no cell service and in areas where there is 1x or 3g and the 4g came back. I even made a backup of the ROM wiped and installed another marshmallow aosp rom and others. I then went to restore BlackSoulxxx ROM and 4g signal still came back.
Steps I did.
1. Tot'd back to stock 10b and rooted and installed twrp.
2. Flashed LG_G3_Flash2BackupEFS.zip of the 10b rom.
3. Wiped stock 10b and flashed the 10b G3_EFS_Flashable_Restore.zip that was created from the the LG_G3_Flash2BackupEFS.zip.
4. Flashed BlackSoulxxx rom and after it booted up I had signals but not data until I entered the Verizon APN manually see picture of what to enter. If mobile network is greyed out flash 35b bootstack.
5. I entered the verizon APN and selected CDMA then global I got the 4g icon with signal bars I changed the icon with a buildprop edit.
I just don't get signals while in 1x or 3g but data does work still and it will get 4g again if your in a 4g area. The phone does say T-CDMA 64. Here's a https://drive.google.com/file/d/0B-EyVOQK1xDAa0VmbERXcUlrV1U/view?usp=sharing to change it to Verizon Wireless courtesy of @xpirt.
netookska05 said:
I am on BlackSoulxxx latest LG G3 Tekcafe v5.3 D85530A-Full G5 ROM. Here's what I did to get the bars with 4g data. I tested it out in areas where there is no cell service and in areas where there is 1x or 3g and the 4g came back. I even made a backup of the ROM wiped and installed another marshmallow aosp rom and others. I then went to restore BlackSoulxxx ROM and 4g signal still came back.
Steps I did.
1. Tot'd back to stock 12b and rooted and installed twrp.
2. Flashed LG_G3_Flash2BackupEFS.zip of the 12b rom.
3. Wiped stock 12b and flashed the 12b G3_EFS_Flashable_Restore.zip that was created from the the LG_G3_Flash2BackupEFS.zip.
4. Flashed BlackSoulxxx rom and after it booted up I had signals but not data until I entered the Verizon APN manually see picture of what to enter. If mobile network is greyed out flash 35b bootstack.
5. I entered the verizon APN and selected CDMA then global I got the 4g icon with signal bars I changed the icon with a buildprop edit.
I just don't get signals while in 1x or 3g but data does work still and it will get 4g again if your in a 4g area. The phone does say T-CDMA 64. Here's a https://drive.google.com/file/d/0B-EyVOQK1xDAa0VmbERXcUlrV1U/view?usp=sharing to change it to Verizon Wireless courtesy of @xpirt.
Click to expand...
Click to collapse
Great job posting your step by step instructions. I've been able to achieve all of the same on a host of international ROMS however with a couple of caveots. I can either have SMS/MMS working properly, or break SMS/MMS and have internet with signal bars. Question about the file above. This will just modify the header, or will it specifically put you on the Verizon network?
Sent from my VS985 4G using XDA-Developers mobile app
b00ster23 said:
Great job posting your step by step instructions. I've been able to achieve all of the same on a host of international ROMS however with a couple of caveots. I can either have SMS/MMS working properly, or break SMS/MMS and have internet with signal bars. Question about the file above. This will just modify the header, or will it specifically put you on the Verizon network?
Sent from my VS985 4G using XDA-Developers mobile app
Click to expand...
Click to collapse
It'll change just the ROM from saying T-CDMA 64 to Verizon Wireless for Verizon users (VS985).
netookska05 said:
It'll change just the ROM from saying T-CDMA 64 to Verizon Wireless for Verizon users (VS985).
Click to expand...
Click to collapse
So when you go into the About Phone>Network, does it say Verizon Wireless for the network?
Hello good people,
I live in the UK, where the V20 was not released.
I have bought the AT&T unlocked H910 from Ebay, as it was stating that it works in the UK,
but the LTE band used by my carrier 800 MHz band 20 is not available on this phone.
"LTE band 1(2100), 2(1900), 3(1800), 4(1700/2100), 5(850), 7(2600), 12(700), 29(700), 30(2300)"
I have followed some of the noob guides and reading for days I believe that I have successfully rooted the phone, (shows in root checker). - as after some reading I was led to believe that by rooting the phone i would be able to change these settings via an app. however this did nothing for me.
could someone please kindly point me in the direction so that I can mod this so that the phone picks up and communicates with the correct Band? is this possible at all? or should i just try to return this to stock and return the phone?
or is this a situation where i just bought myself a small tablet?
I would be grateful for any help in solving this issue,
Many thanks in advance ! :good:
kneuast said:
Hello good people,
I live in the UK, where the V20 was not released.
I have bought the AT&T unlocked H910 from Ebay, as it was stating that it works in the UK,
but the LTE band used by my carrier 800 MHz band 20 is not available on this phone.
"LTE band 1(2100), 2(1900), 3(1800), 4(1700/2100), 5(850), 7(2600), 12(700), 29(700), 30(2300)"
I have followed some of the noob guides and reading for days I believe that I have successfully rooted the phone, (shows in root checker). - as after some reading I was led to believe that by rooting the phone i would be able to change these settings via an app. however this did nothing for me.
could someone please kindly point me in the direction so that I can mod this so that the phone picks up and communicates with the correct Band? is this possible at all? or should i just try to return this to stock and return the phone?
or is this a situation where i just bought myself a small tablet?
I would be grateful for any help in solving this issue,
Many thanks in advance ! :good:
Click to expand...
Click to collapse
Hi
You need to get into the service menu on the 910 and search for the 20 band and enable it. Sorry I cannot be more specific. You can google for the code(s) that will get you into the service menu.
I have a V20 but it is Verizon vs995 which has the correct bands but for some reason will not work with EE 4G only 3G.
Sent from my iPad using Tapatalk
Stransky said:
Hi
You need to get into the service menu on the 910 and search for the 20 band and enable it. Sorry I cannot be more specific. You can google for the code(s) that will get you into the service menu.
I have a V20 but it is Verizon vs995 which has the correct bands but for some reason will not work with EE 4G only 3G.
Sent from my iPad using Tapatalk
Click to expand...
Click to collapse
Thank you for your reply,
I have tried this, i think i can get in by code *#546368#*910# assuming that this is what you are talking about?
this will take me to hiddenmenu
with 4 sub menues
- device test
- ELT Test
- SVC Test
- Field Test
I believe that i've seen people try to access the modem settings in the field test option
and i have seen that people get 3 or more options in this place, (third allowing you to select band) where as I only get 2
- Engineering mode
- PDP settings
do you know why the option does not appear for me?
- Would there be a chance that the option was hidden from the start by AT&T ?
Also I did not do LGUP dump before the root where many people in their guides have pointed out to
do, i followed a guide which does not involve LGUP to attempt to root my phone, should I try to flash the phone in a different firmware to try to unlock the mode ? along with the LGUP dump ?
again, thanks for the response !
Sorry, don't know but have you tried SVC entry I seem to remember some in the US using that to alter their Band.
The code you used does not work for me on my V20 in fact apart from IMEI code *#06# no codes work o. My phone.
Stransky said:
Sorry, don't know but have you tried SVC entry I seem to remember some in the US using that to alter their Band.
The code you used does not work for me on my V20 in fact apart from IMEI code *#06# no codes work o. My phone.
Click to expand...
Click to collapse
Hi thanks again for getting back to me,
I am sorry but i do not know what SVC entry is, any relating articles i find are about terminal entry? is this in the ball park ?
could you point me in the direction of where i may find the information to do this myself ?
Ty
I meant SVC Test entry. Other than that I do not know. Sorry.
Hi Stransky,
Did you ever get your h910 to work in the UK? I think I have the same issue with my V20 h910
jimjim79 said:
Hi Stransky,
Did you ever get your h910 to work in the UK? I think I have the same issue with my V20 h910
Click to expand...
Click to collapse
If you are in the UK then you don't need H910 rom. Flash it with US996 [usa] KDZ and that will sort out all the band issues without having to do anything more. Plus get's rid of At&T bloatware as US996 doesn't have any carrier bloat or network restrictions. I'm in Ireland and the rom is working great, 4G+ etc. My phone was originally a Verizon model.
edit: One drawback is you will loose FM radio as it's not on the US996 rom. If you are able to root the fone you can get it back with my mod if your on oreo.
thanks don't want to use the FM radio so will try your mod. Is there a guide to flash US996?
I'm being told in another thread that flashing another rom can't give you extra bands, so I'm a little confused between the contradictory advice.
ROMs do not have anything to do with available bands. Bands are hardware dependant
Click to expand...
Click to collapse
jimjim79 said:
I'm being told in another thread that flashing another rom can't give you extra bands, so I'm a little confused between the contradictory advice.
Click to expand...
Click to collapse
Your answer is in bold. He just gave bad advice. If you look earlier in the thread the Verizon variant has those bands already.
ezzony said:
If you are in the UK then you don't need H910 rom. Flash it with US996 [usa] KDZ and that will sort out all the band issues without having to do anything more. Plus get's rid of At&T bloatware as US996 doesn't have any carrier bloat or network restrictions. I'm in Ireland and the rom is working great, 4G+ etc. My phone was originally a Verizon model.
edit: One drawback is you will loose FM radio as it's not on the US996 rom. If you are able to root the fone you can get it back with my mod if your on oreo.
Click to expand...
Click to collapse
You can buy a US996 v20 on eBay for $86 with free shipping in the US. Probably your best bet. V30 and G7 unlocked phones aren't too expensive either in good condition, though I have not cross referenced which bands they have, so you'd have to double check. I like the phone myself, might buy a couple so relatives have backup phones.
Let me be clear. The H910, VS995, US996, on a hardware level have exactly the same motherboard, The only difference is the software...the ROM. So for example VS995, US996 don't have FM radio out of the box where H910 does. This is a perfect example of where the sofware has been designed to restricted FM radio leading one to *think* the fone doesn't have FM radio on some models at all but in fact it does.
So, It the same idea for BANDS. A fone MAY be missing bands out of the box because the ROM has been designed to restrict some of the the bands where in reality the fone has those bands. So in that case you can overcome this by changing to a ROM that does not have this restriction enabled in the ROM, in exactly the same way as in the case of FM radio. Carriers do disable bands on fones for their own devious reasons.
I know from experience H910 has hotspot restrictions as well. There is a work around OR you can just flash US996 that does not have this hotspot restriction. Also H910 has restriction in the Mobile Settings section. If you change to US996 there will be extra settings in Mobile networks>System Select settings which are GLOBAL / LTE/CDMA, LTE/GSM/UMTS. These options I'm sure I recall did not show up on H910 rom which could be useful to some.
I did not have an original H910 but all I'm saying is that I'm fairly sure that the motherboard is exactly the same as the other models in which case it will have all the same bands as Verizon and US996, just you can't see them because of H910 software on it. Of course you can't enable bands if they don't exist on the motherboard but you can if they do exist but have been restricted by the ROM.
So to the guy who asked about the H910 you can try to use the service menu to enable bands BUT this is not the best way to do it as the service menu might not let you or maybe the enable doesn't last after rebooting. The best way to fix this is to flash a ROM that does not have network restrictions and then you can forget out it from there on in.
---------- Post added at 12:56 PM ---------- Previous post was at 12:47 PM ----------
jimjim79 said:
I'm being told in another thread that flashing another rom can't give you extra bands, so I'm a little confused between the contradictory advice.
Click to expand...
Click to collapse
Please see my previous post.
You have 2 options. You can either flash a clean US996 KDZ that you download at https://lg-firmwares.com. You'd need LGUP to flash it, guides on youtube and here, search for them. You don't have to be rooted to flash a new KDZ.
If you are rooted you can just download a custom ROM from here such as WETA ROM US996santa version and flash it in TWRP. You could backup your current system just in case it doesn't solve your problem but even if your problem isn't solved the US996 rom would be better anyway for the other reasons I mentioned in my previous post plus I forgot to add that would get rid of all the AT&T bloatware as well.
thanks for the advice, I'm really struggling to find a guide that matched my requirements or is there a generic guide I can follow. Bit scared as I'm reading some roms will brick the device.
Don't need to root at the moment so hopefully that will make it simpler.
ezzony said:
If you are in the UK then you don't need H910 rom. Flash it with US996 [usa] KDZ and that will sort out all the band issues without having to do anything more. Plus get's rid of At&T bloatware as US996 doesn't have any carrier bloat or network restrictions. I'm in Ireland and the rom is working great, 4G+ etc. My phone was originally a Verizon model.
edit: One drawback is you will loose FM radio as it's not on the US996 rom. If you are able to root the fone you can get it back with my mod if your on oreo.
Click to expand...
Click to collapse
Hi there - can you please point me to the rom you use? I just got a H910 from ebay at&t 'unlocked'. But I found only 2g on the stock rom. Have flashed a variety of U996, H915 (canada), and a H910pr (puerto rico) but can only get 3g sometimes. Some of the android 7 roms don't even have 4g as one of the options. Others do but I cannot select it - only 3g.
I'm in the UK but the 800/1800 bands Ireland uses are also the same for EE in the Uk.
Many thanks!
I've been looking for a good, inexpensive phone my partner can use on AT&T, T-Mobile and Verizon and I was able to snatch an unlocked VS995 in excellent condition for $70--it just needs the battery replaced soon which I also ordered. The main downside to this model if you're using it on AT&T and T-Mobile is that it doesn't support Band 12 and 17, but I know the US Unlocked variant does. I just received the phone today. I've been searching on the forum for an answer into if this is possible with the VS995 variant and I've seen people say it is using an LG V20 version of LGUP, but haven't found anyone that's confirmed they've been able to do it on the Verizon and not the AT&T variant and the steps they took to do so.
I want to stay on the stock ROM so I'm not looking to root and install a custom one. Is it possible to convert from the VS995 firmware to US996 so I can gain band 12 and 17 while removing the Verizon bloatware and staying on the stock ROM/OS? If so, would anyone one of y'all be kind enough to post the link to a guide or article that details how to do so? I reset the phone to factory settings so thankfully don't have to do a backup. After doing this, is it still possible to receive OTA updates and, if so, are they gonna mess anything up like reverting the phone to stock firmware or the phone's unlocked status?
Thank y'all so much in advance.
I have a vs995 and I flashed it with US996_usa and working great. You need to download the us996 usa version (2.3GB KDZ) at lg-firmwares dot com and flash it with LGUP PATCHED. There is video on Youtube giving detailed instructions. You will be able to find all these easily via google. I don't know how any of this works with the various US carriers or bands as I'm in europe.
DeyEatDaPooPoo said:
I've been looking for a good, inexpensive phone my partner can use on AT&T, T-Mobile and Verizon and I was able to snatch an unlocked VS995 in excellent condition for $70--it just needs the battery replaced soon which I also ordered. The main downside to this model if you're using it on AT&T and T-Mobile is that it doesn't support Band 12 and 17, but I know the US Unlocked variant does. I just received the phone today. I've been searching on the forum for an answer into if this is possible with the VS995 variant and I've seen people say it is using an LG V20 version of LGUP, but haven't found anyone that's confirmed they've been able to do it on the Verizon and not the AT&T variant and the steps they took to do so.
I want to stay on the stock ROM so I'm not looking to root and install a custom one. Is it possible to convert from the VS995 firmware to US996 so I can gain band 12 and 17 while removing the Verizon bloatware and staying on the stock ROM/OS? If so, would anyone one of y'all be kind enough to post the link to a guide or article that details how to do so? I reset the phone to factory settings so thankfully don't have to do a backup. After doing this, is it still possible to receive OTA updates and, if so, are they gonna mess anything up like reverting the phone to stock firmware or the phone's unlocked status?
Thank y'all so much in advance.
Click to expand...
Click to collapse
As far as I'm aware, cross-flashing firmware on the V20 won't give you any additional frequency bands unlike some other phones, so you're still limited to what the VS995 has from the beginning. From what I've read, US996 firmware works fine on Verizon except for a few features such as WiFi calling and video calling.
As for AT&T and T-Mobile, you won't get VoLTE or WiFi calling along with the missing LTE bands, so, depending on where you live, overall coverage could be significantly worse than having the H910 (AT&T) and H918 (T-Mobile) models, respectively. Not having VoLTE would be a problem if you were in an LTE-only area without roaming because then you'd have no way to make or receive phone calls.
ezzony said:
I have a vs995 and I flashed it with US996_usa and working great. You need to download the us996 usa version (2.3GB KDZ) at lg-firmwares dot com and flash it with LGUP PATCHED. There is video on Youtube giving detailed instructions. You will be able to find all these easily via google. I don't know how any of this works with the various US carriers or bands as I'm in europe.
Click to expand...
Click to collapse
Thank you for the info. Are you referring to this video? I'd watched it before but it's for flashing the stock ROM on a US996 variant and the links in the description don't work.
C D said:
As far as I'm aware, cross-flashing firmware on the V20 won't give you any additional frequency bands unlike some other phones, so you're still limited to what the VS995 has from the beginning. From what I've read, US996 firmware works fine on Verizon except for a few features such as WiFi calling and video calling.
As for AT&T and T-Mobile, you won't get VoLTE or WiFi calling along with the missing LTE bands, so, depending on where you live, overall coverage could be significantly worse than having the H910 (AT&T) and H918 (T-Mobile) models, respectively. Not having VoLTE would be a problem if you were in an LTE-only area without roaming because then you'd have no way to make or receive phone calls.
Click to expand...
Click to collapse
Hmm, where did you read that? From what I've read the hardware/modem in the VS995 and US996 version is the same and therefore the difference only comes down to the carrier firmware artificially disabling bands the device supports just like it is on many other smartphones. I could be wrong, but one way to find out would be to do it myself and then try to connect to a Band 12 or 17 tower.
WiFi calling and video calling I'm totally fine with not having. Never used or needed them. With AT&T and Cricket I've never not had service and with Metro the couple times I haven't had T-Mobile service roaming has kicked in and saved the day. Thank you for the info.
DeyEatDaPooPoo said:
Hmm, where did you read that? From what I've read the hardware/modem in the VS995 and US996 version is the same and therefore the difference only comes down to the carrier firmware artificially disabling bands the device supports just like it is on many other smartphones. I could be wrong, but one way to find out would be to do it myself and then try to connect to a Band 12 or 17 tower.
WiFi calling and video calling I'm totally fine with not having. Never used or needed them. With AT&T and Cricket I've never not had service and with Metro the couple times I haven't had T-Mobile service roaming has kicked in and saved the day. Thank you for the info.
Click to expand...
Click to collapse
Here's some frequency band info for both the VS995 and US996:
VS995
US996
I'm pretty sure this is a hardware difference, and no firmware change will be able to add more band support unlike some other phones you may have heard about (such as recent U.S. models of Samsung phones). Otherwise, there would have been plenty of discussions and guides around here regarding this (and FWIW, I happen to own a US996, LS997, and H918).
As for LTE Band 12 on the T-Mobile network, only phones that are certified by T-Mobile will be able to access it (more info on compatible phones here). So even though a US996 has the hardware for connecting to Band 12, you wouldn't be able to use it since T-Mobile has blocked access to it and only allows it for the H918 model.
Based on all this, I would expect a VS995 to get LTE Bands 2, 4, and 5 on AT&T and T-Mobile. Of course, since you already have the phone, there's only one way to find out. Just make sure you carefully read the guides/procedures about using LGUP for cross-flashing, and absolutely stay away from any H918 firmware (it will instantly kill any V20 that is not an actual H918). Not sure if there even is a separate guide around here as it is usually mentioned in the initial steps of different rooting guides for each V20 model, but you can find the patched LGUP that ezzony mentioned in this thread (you may have to move the DLL file to a specific folder location for it to work properly).
C D said:
Here's some frequency band info for both the VS995 and US996:
VS995
US996
I'm pretty sure this is a hardware difference, and no firmware change will be able to add more band support unlike some other phones you may have heard about (such as recent U.S. models of Samsung phones). Otherwise, there would have been plenty of discussions and guides around here regarding this (and FWIW, I happen to own a US996, LS997, and H918).
As for LTE Band 12 on the T-Mobile network, only phones that are certified by T-Mobile will be able to access it (more info on compatible phones here). So even though a US996 has the hardware for connecting to Band 12, you wouldn't be able to use it since T-Mobile has blocked access to it and only allows it for the H918 model.
Based on all this, I would expect a VS995 to get LTE Bands 2, 4, and 5 on AT&T and T-Mobile. Of course, since you already have the phone, there's only one way to find out. Just make sure you carefully read the guides/procedures about using LGUP for cross-flashing, and absolutely stay away from any H918 firmware (it will instantly kill any V20 that is not an actual H918). Not sure if there even is a separate guide around here as it is usually mentioned in the initial steps of different rooting guides for each V20 model, but you can find the patched LGUP that ezzony mentioned in this thread (you may have to move the DLL file to a specific folder location for it to work properly).
Click to expand...
Click to collapse
Yes, but the Frequency Check website only looks at firmware differences, not the internal hardware. I decided to do some further digging and went to the source that tests these (the FCC) and found that the VS995 and US996 have the same ZNFVS995 FCC ID meaning they share the same internal hardware. Verizon just decided they wanted to be arseholes and cripple the phone's band support in their firmware so it wouldn't work to the best of its abilities on T-Mobile's and AT&T's network. Similarly, T-Mobile decided to also be arseholes by artificially limiting Band 12/VoLTE support to their own H918 model only. I hate that carriers are able to get away with this BS. It is incredibly anti-consumer and infuriating. If the hardware supports XYZ then it should be enabled and capable of taking advantage of it. The FCC tested Band 12/17 to work properly on these and says regarding the device's capabilities:
This device contains the following capabilities: 850/1900 CDMA (BC0, BC1), 850/1900 GSM/GPRS/EDGE, 850/1700/1900 WCDMA/HSPA, Multi-band LTE, 802.11b/g/n/ac WLAN, 802.11a/n/ac UNII, Bluetooth (1x, EDR, LE), NFC LTE Band 12 (698 - 716 MHz) overlaps the entire frequency range of LTE Band 17 (704 - 716 MHz). Therefore, test data provided in this report covers Band 17 as well as Band 12. LTE Band 25 (1850 - 1915 MHz) overlaps the entire frequency range of LTE Band 2 (1850 - 1910 MHz). Therefore, test data provided in this report covers Band 2 as well as Band 25. LTE Band 66 (1710 - 1780 MHz) overlaps the entire frequency range of LTE Band 4 (1710 - 1755 MHz). Therefore, test data provided in this report covers Band 4 as well as Band 66.
Click to expand...
Click to collapse
Seriously, f*ck both Verizon and T-Mobile. Thankfully I'm starting my Cricket/AT&T service in a week so I'll be able to test if it can pick up and use Band 12/17. You happen to know of any app or way to force/limit the device to only using one specific LTE band? Thank you so much for linking to that thread for flashing these using LGUP. I'll make sure to follow it and to download the US996 (US Unlocked, not US Cellular) firmware and post a small update on my findings. Thank you so much for all the info. Really appreciate it.
DeyEatDaPooPoo said:
You happen to know of any app or way to force/limit the device to only using one specific LTE band?
Click to expand...
Click to collapse
While I've never tried this, have a look at this old thread on LTE band selection from a hidden menu. The dialer code differs by model, so for a VS995 it would be *#546368#*995# and for a US996 *#546368#*996#. The code works for my US996 and H918 on Oreo but not for my LS997 on Nougat (for which there is a separate APK file to access the hidden menu). There are lots of submenus and items in there, so be sure not to accidentally change settings that you're not supposed to.
ezzony said:
I have a vs995 and I flashed it with US996_usa and working great. You need to download the us996 usa version (2.3GB KDZ) at lg-firmwares dot com and flash it with LGUP PATCHED. There is video on Youtube giving detailed instructions. You will be able to find all these easily via google. I don't know how any of this works with the various US carriers or bands as I'm in europe.
Click to expand...
Click to collapse
Hello
You crossflash with which android version 9 or 8
If android 9 whats the battery backup (good/bad)
Does the android 9 has a darkmode
Does it brings back or activate the FM radio ?
Thanks
mariowinax said:
Hello
You crossflash with which android version 9 or 8
If android 9 whats the battery backup (good/bad)
Does the android 9 has a darkmode
Does it brings back or activate the FM radio ?
Thanks
Click to expand...
Click to collapse
Android 8.
I know Android 9 does not have FM radio because Android 9 is only available for the Korean variant (F800) and it never had FM in the first place.
ezzony said:
I have a vs995 and I flashed it with US996_usa and working great. You need to download the us996 usa version (2.3GB KDZ) at lg-firmwares dot com and flash it with LGUP PATCHED. There is video on Youtube giving detailed instructions. You will be able to find all these easily via google. I don't know how any of this works with the various US carriers or bands as I'm in europe.
Click to expand...
Click to collapse
I have heard about converting a vs995 to a us996. How do you do this i have a vs995 and patched lg up do i use the upgrade option or partion dl?
Thanks,
ROMSG
ROMSG said:
I have heard about converting a vs995 to a us996. How do you do this i have a vs995 and patched lg up do i use the upgrade option or partion dl?
Thanks,
ROMSG
Click to expand...
Click to collapse
DL partition ignores model codes ...so DL Partition.
ezzony said:
DL partition ignores model codes ...so DL Partition.
Click to expand...
Click to collapse
Thanks, now it gives me a partition selection which partitions do i select or do i select all of them?
ROMSG said:
Thanks, now it gives me a partition selection which partitions do i select or do i select all of them?
Click to expand...
Click to collapse
All of them seems to work fine.
Will this work in terms of flashing us unlocked firmware or my Verizon LG v20 (vs995) I rooted it successfully, but when I flash these firmware files, the phone is in a bootloop. US996 twrpable zips