Can anyone suggest a good back cover possible something made of rubber like material that will save the phone if it falls from a particular height
AND
Can anyone suggest a screenguard that has cuttings and marking for all the stuff on the front screen like camera, light sensor and etc
And
Has anyone tried any type-C adapter on zenfone 3. I wanted to buy OnePlus 2 USB Type-C Adapter (Red). Any ideas if it will work ???
thanks
swaid_dx said:
Can anyone suggest a good back cover possible something made of rubber like material that will save the phone if it falls from a particular height
AND
Can anyone suggest a screenguard that has cuttings and marking for all the stuff on the front screen like camera, light sensor and etc
And
Has anyone tried any type-C adapter on zenfone 3. I wanted to buy OnePlus 2 USB Type-C Adapter (Red). Any ideas if it will work ???
thanks
Click to expand...
Click to collapse
I got this http://amzn.to/2cLwf3i
Got Screen guard from local shop
And yes OnePlus 3 adapter will work with ZF3
Related
I bought a magnetic cover for my N10 and have found that it will blank the screen if the cover is wrapped around the BACK of the device. Can anyone suggest a good way of shielding the rear of the tablet that will stop this?
My HTC HD2 with kitkat os falling from my hand and after that the screen shows nothing, my phone is alive and everything works like ringing vibrate alarm even touch screen and touch vibrate, but i see nothing and the display is dark.
whats my problem? can i fix it?
thanks for reply me
any body ????
muhama said:
My HTC HD2 with kitkat os falling from my hand and after that the screen shows nothing, my phone is alive and everything works like ringing vibrate alarm even touch screen and touch vibrate, but i see nothing and the display is dark.
whats my problem? can i fix it?
thanks for reply me
Click to expand...
Click to collapse
any body ????
probably need new screen assembly!
needs opening to check lcd connector to mainboard & if all connections good then new screen should be tried.
LCD & digitizer pre built assembly is only about $30 these days for decent ones but indeed not easy fit with some experience or good read up on procedure & good care when doing it.
Mister B said:
probably need new screen assembly!
needs opening to check lcd connector to mainboard & if all connections good then new screen should be tried.
LCD & digitizer pre built assembly is only about $30 these days for decent ones but indeed not easy fit with some experience or good read up on procedure & good care when doing it.
Click to expand...
Click to collapse
Thanks for reply me:good:
How can i open my phone? And where is connector located?
Do you have a link to view that?
Have a read of this thread for start
http://forum.xda-developers.com/showthread.php?t=1566179
Plenty more if do a search
Basically be very very careful, use plastic pry tool ONLY to remove back, start at top. 2 clips about 7mm in from top edges then once released work down right side, DO NOT stick any tools in near the volume key, if doing it right the back comes of very easy (2 pry tools are better as can keep one in top sstopping it clipping back in)
Once back off handle with care, rough handling breaks th spring contacts for antenna etc.
LCD from mainboad can be disconnected from mainboard without fully removing flex & is absolute best way do it.
I did write few posts on it so will try dig them up & link you.
If buy lcd/gigi assemble also buy a button board ribbon as they like only $3USD, with spare button ribbon you can easily plug new lcd/digi in & plug new button board ribbon into mainboard & hold a battery on it to do a test befoe sticking things together.
Also you likely damage ribbon if not careful so spare likely get used on rebuild.
Parts link is in HD2 Wiki
http://forum.xda-developers.com/wiki/HTC_HD2#Fixes.2C_Hints_.26_Tips
Hi guys, yesterday I've repair my broken d802 (headphone jack broken) and everything goes fine.
But, while I starting to close the back cover I've notice something strange:
a lot of paper clip and needles I have on the desk start to get attracted by the phone, in a first place I thought it was normal (speaker has a magnet) but the magnetic field is near the camera.
Also with the back cover on, it still attract a bit paper clips.
It is normal?
Does your d802 do the same?
the exact place is just some millimetres above the camera.
Thank you in advance
Mine does the same, must be some component that causes this..
so it's not my fault while I was trying to replace the part
Don't think so, but I've previously replaced my screen so it could be different from original parts?
Recently replaced the back glass on the S8 and it occurred to me that perhaps the magnetic pads that come with some magnet car mounts might fit under the glass.
I don't have any double-sided tape or the tools to try it to do it on my own. Was wondering if anyone has tried to do this. This JUST occurred to me, if not I would have tried it when I replaced the back panel :crying:
I know it will cause problems with wireless charging (feature I don't make use of) but would be nice to be able to use it once I get my new Dbrand Grip + Black Camo skin.
Anyone capable of trying this out, or has tried it and can provide feedback if there is enough room or not??
Attached is an image of the mount + plate + phone setup.
You can get a spigen liquid crystal case and put the metal between.
I have a spigen case, glued metal plate and the wireless charging still works. Any other thin case will do.
Hello everyone i need huawei mate 9 schematic diagram. Can anyone help on this? My mate 9 vibrator not working and need to find vibrator ways.. :crying:
This looks like it will do you.
https://www.ebay.com/itm/for-Huawei...brator-Motor-Flex-Cable-ZVFE313-/192439428478
I don't know exactly where its located, but its along the top of the phone. When I had my screen replaced, it was seated behind the screen and now it sounds like a tin can when it vibrates. So just a FYI if you replace it and it sounds odd afterward.
cash2387 said:
This looks like it will do you.
https://www.ebay.com/itm/for-Huawei...brator-Motor-Flex-Cable-ZVFE313-/192439428478
I don't know exactly where its located, but its along the top of the phone. When I had my screen replaced, it was seated behind the screen and now it sounds like a tin can when it vibrates. So just a FYI if you replace it and it sounds odd afterward.
Click to expand...
Click to collapse
It's on the bottom left corner of the device, looking from the display side. Under the USB daughterboard, which is a bit fiddly to get out because one of the flex cables attached to it is easily missed.
In the picture, it's the round silver object on the right side, next to the flex cable going to the main board.
Azan Mughal said:
Hello everyone i need huawei mate 9 schematic diagram. Can anyone help on this? My mate 9 vibrator not working and need to find vibrator ways.. :crying:
Click to expand...
Click to collapse
Google for Mate 9 teardown, there are Web and YT guides with pictures, etc
I have already changed the vibrator but it sound tiny
And this problem was come after change my touch glass and after change vibrator problem is same too low sound from vibrator and they tell that voltage problem i don't know now what to do if any body tell me who's have the same problem solved.