Related
Hey everyone,
So, I'm pretty new to Android having had the past two iterations of the Nexus 7 and decided to take the leap from an iPhone (which I had jailbroken) to a Samsung Galaxy S4 GT-I9505 LTE, which I bought unlocked and outright.
I ran stock TouchWiz for a while and then wanted to play, so installed FoxHound 3.2. This worked fine for some time, but then I started getting random reboots which seemed to coincide with listening to music on the device. After a while the reboots suddenly became more regular and it got so I couldn't even open WhatsApp without it either restarting or going into a bootloop. Usually, if it went into a bootloop and I tried starting the phone straight away it would fail, but if I left it off for some time it would start up okay, only to reboot again later if I used it for anything. I also noticed the battery draining quickly.
I tried flashing the device with various other ROMs - PACMan, Google AOKP, etc. - but got the same issue. Many times, the system would crash just when I first started to setup the phone. I finally determined the reason it was crashing at the initial startup was that it was when WiFi was being enabled. So, I ended up following a fruitless several hours of attempting to fix the WiFi using files provided on this page: http://forum.xda-developers.com/showthread.php?t=2192025. I tried XXUDMH8, XXUEMJ7 and XXUEMK8 all to no avail - I installed both the firmware and the WiFi fix files using Odin and thought I had it cracked, only for my phone to eventually reboot again whilst WiFi was not even enabled - it did take a bit longer this time though, admittedly, but it still rebooted and went into a bootloop.
So, I finally followed this page: http://galaxys4root.com/galaxy-s4-tutorials/how-to-unroot-galaxy-s4-and-remove-root-completely/ to completely return my device to stock TouchWiz, but still no joy.
I have tried factory resetting the device and wiping all cache from the stock recovery and from Philz CWM (which I had while using the custom ROMs), but this does nothing.
I tried connecting my device to Kies now that I have the stock TouchWiz ROM back on the device, but it is now rebooting even more frequently and I can't get in long enough to run the emergency firmware recovery. It used to stay up longer (sometimes indefinitely) when connected to the PC via the Samsung factory cable or to a power supply with the Samsung charger, but now it is even rebooting when plugged in.
I am extremely worried that my device that cost me nearly £600 a few months ago is bricked for good. I did (understandably) think that returning it to default would've resolved the issue, but even this has failed.
Is there ANYTHING else I can try that I have not already........?
KalarAzar said:
Is there ANYTHING else I can try that I have not already........?
Click to expand...
Click to collapse
hello mate, what bootloader do you have?(Boot into download mode too see if it says Knox void warranty or not) and can you still boot into download mode? thanks
Repulsa said:
hello mate, what bootloader do you have?(Boot into download mode too see if it says Knox void warranty or not) and can you still boot into download mode? thanks
Click to expand...
Click to collapse
Hi and thanks for your reply,
I can boot into download mode - one of the only things I can do! - and it says 0x1 under KNOX WARRANTY VOID, so yes it is showing Knox void.
Just in case you need it, the full information shown on the screen in download mode is as follows:
ODIN MODE
PRODUCT NAME: GT-I9505
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enable
eMMC BURST MODE enabled
Thanks again..
KalarAzar said:
Thanks again..
Click to expand...
Click to collapse
I want you to flash the 4.3 stock rom firmware from samsung (Sign up)www.sammobile.com/firmwares/1/ make sure to choose the right one such as device, country . Then when your done flash the file via odin 3.09 and select AP ,Or follow the instruction from here, how to do a proper flash. http://forum.xda-developers.com/showthread.php?t=2252982 . have a nice day.
Repulsa said:
I want you to flash the 4.3 stock rom firmware from samsung (Sign up)www.sammobile.com/firmwares/1/ make sure to choose the right one such as device, country . Then when your done flash the file via odin 3.09 and select AP ,Or follow the instruction from here, how to do a proper flash. http://forum.xda-developers.com/showthread.php?t=2252982 . have a nice day.
Click to expand...
Click to collapse
Hey Repulsa,
Thanks again. Unfortunately, this is what I did. I signed up at samfirmware and downloaded the file: I9505XXUEMK8_I9505BTUEMK5_BTU.zip
The only thing I did different was that I used Odin 3.07 and flashed using the PDA option, but I'm presuming this is the same thing..? After the bootloop, I went into recovery and factory reset, but still the bootloop occurs.
I have since managed to get into my phone after leaving it off for a couple of hours again and looking through the settings it says I have "Samsung" as the secure boot status and "Official" as the device status. The build number is showing up as JSS15J.I9505XXUEMK8 on Android 4.3.
Should I try anything else that you can think of?
Thanks again for the reply.
KalarAzar said:
Hey Repulsa,
Thanks again. Unfortunately, this is what I did. I signed up at samfirmware and downloaded the file: I9505XXUEMK8_I9505BTUEMK5_BTU.zip
The only thing I did different was that I used Odin 3.07 and flashed using the PDA option, but I'm presuming this is the same thing..? After the bootloop, I went into recovery and factory reset, but still the bootloop occurs.
I have since managed to get into my phone after leaving it off for a couple of hours again and looking through the settings it says I have "Samsung" as the secure boot status and "Official" as the device status. The build number is showing up as JSS15J.I9505XXUEMK8 on Android 4.3.
Should I try anything else that you can think of?
Thanks again for the reply.
Click to expand...
Click to collapse
is the problem still persist? if it does Turn off your phone and Press and hold Power+Volume up and do another Wipe cache and Factory reset.
Repulsa said:
is the problem still persist? if it does Turn off your phone and Press and hold Power+Volume up and do another Wipe cache and Factory reset.
Click to expand...
Click to collapse
Yes, I'm afraid it does, and I have already done the wipe cache and factory reset, but no joy. I did it again anyway and on reboot it went back into the bootloop again, I'm afraid..
KalarAzar said:
Hey everyone,
So, I'm pretty new to Android having had the past two iterations of the Nexus 7 and decided to take the leap from an iPhone (which I had jailbroken) to a Samsung Galaxy S4 GT-I9505 LTE, which I bought unlocked and outright.
I ran stock TouchWiz for a while and then wanted to play, so installed FoxHound 3.2. This worked fine for some time, but then I started getting random reboots which seemed to coincide with listening to music on the device. After a while the reboots suddenly became more regular and it got so I couldn't even open WhatsApp without it either restarting or going into a bootloop. Usually, if it went into a bootloop and I tried starting the phone straight away it would fail, but if I left it off for some time it would start up okay, only to reboot again later if I used it for anything. I also noticed the battery draining quickly.
I tried flashing the device with various other ROMs - PACMan, Google AOKP, etc. - but got the same issue. Many times, the system would crash just when I first started to setup the phone. I finally determined the reason it was crashing at the initial startup was that it was when WiFi was being enabled. So, I ended up following a fruitless several hours of attempting to fix the WiFi using files provided on this page: http://forum.xda-developers.com/showthread.php?t=2192025. I tried XXUDMH8, XXUEMJ7 and XXUEMK8 all to no avail - I installed both the firmware and the WiFi fix files using Odin and thought I had it cracked, only for my phone to eventually reboot again whilst WiFi was not even enabled - it did take a bit longer this time though, admittedly, but it still rebooted and went into a bootloop.
So, I finally followed this page: http://galaxys4root.com/galaxy-s4-tutorials/how-to-unroot-galaxy-s4-and-remove-root-completely/ to completely return my device to stock TouchWiz, but still no joy.
I have tried factory resetting the device and wiping all cache from the stock recovery and from Philz CWM (which I had while using the custom ROMs), but this does nothing.
I tried connecting my device to Kies now that I have the stock TouchWiz ROM back on the device, but it is now rebooting even more frequently and I can't get in long enough to run the emergency firmware recovery. It used to stay up longer (sometimes indefinitely) when connected to the PC via the Samsung factory cable or to a power supply with the Samsung charger, but now it is even rebooting when plugged in.
I am extremely worried that my device that cost me nearly £600 a few months ago is bricked for good. I did (understandably) think that returning it to default would've resolved the issue, but even this has failed.
Is there ANYTHING else I can try that I have not already........?
Click to expand...
Click to collapse
it can be a bad battery aswell if your battery serial starts with BD exchange it asap you may also experience any issues mentioned in this thread http://forum.xda-developers.com/showthread.php?t=2570608
Acer4605 said:
it can be a bad battery aswell if your battery serial starts with BD exchange it asap you may also experience any issues mentioned in this thread http://forum.xda-developers.com/showthread.php?t=2570608
Click to expand...
Click to collapse
Ah FFS. My battery serial does start with BD and I was wondering if it was a battery issue, but didn't want to replace it if the fault was wider spread. I guess I may have to try this then..
I'm just flashing to MJ7 right now, but if it reboots again I will see about a new battery from where I bought it on Monday
And, as I forgot to say in the last post: thanks for your reply. If this fixes it, much kudos, my friend..
Yep. The flashing of MJ7 did not work. Maybe my battery is a dud as it went straight back into a bootloop at the Samsung logo.
Carphone Warehouse visit on Monday methinks..
KalarAzar said:
Yep. The flashing of MJ7 did not work. Maybe my battery is a dud as it went straight back into a bootloop at the Samsung logo.
Carphone Warehouse visit on Monday methinks..
Click to expand...
Click to collapse
you can get passed the samsung logo if you boot while your charger is connected to the phone, the battery might swell as well or is already bigger then it originally was
My phone has been randomly shutting down over the past couple of days and the only way I can get it to boot is to connect a charger/cable to pc. I've tried different ROMs and returning to stock. No joy.
I guess my battery could well be the problem
---------- Post added at 11:33 AM ---------- Previous post was at 11:28 AM ----------
My phone has randomly started shutting down over the past couple of days and the only way I can get it to boot is to connect charger/cable to pc. When it dies, it also loses all of my wifi passwords. It's a bit of a head scratcher. Any help appreciated
Definately the battery, dude
I was experiencing the same problems, and I observed that the battery swollen. So I replaced it and now the phone is functioning properly. Do not wait for the battery to modify its volume because you are risking to put pressure on the display and crack it. Beware.
Was, indeed, the battery
Hey everyone,
Just to let you know that I went back to Phones4u with the receipt from September (when I bought the new phone) and they filled out a form to request a new battery from Samsung and replaced mine their and then in the shop with a new battery from another Samsung Galaxy S4.
My old battery did, indeed, have a serial number that started with BD and the new one starts with AA so hopefully I am now sorted.
Massive thanks to everyone who replied and hopefully this thread will save someone else the time and lost data that flashing ROMs can incur.
Cheers,
A very happy Steve :laugh:
Hello, my SM-G935A is rooted, and I have 2 issues with it. Firstly, I'm unable to receive texts or phone calls (I can send them), and I've tried a factory reset and I even got a new SIM, but nothing worked. I think if I flash stock firmware, it might fix the issue. Second problem, when I go into download mode and select my AP in Odin and press start, my phone gets an error and Odin freezes at Initialization.
Any help would be appreciated. I would prefer to fix the texting issue, as I don't want to return the phone to ATT. In either case, the Odin issue needs to be fixed
I'm having a similar issue. This afternoon, 2 apps threw errors and closed. I rebooted, which apparently was the wrong thing to do. The reboot stalled on the AT&T logo and stayed that way for 5 min - the unit became very hot & the power button did not respond, even while holding it down. I got into recovery, cleared the cache and factory reset, then rebooted. The unit came back up and started reinstalling everything. I took it back down into the download status and attempted to reload 935x via Odin, only to stall at "initialzation" [sic] as you did. I got out of that after waiting for some sort of response. SuperSU was still in my apps as was Root Checker. Root Checker indicates the system is rooted. SuperSU indicates it needs the binary updated. BusyBox and TiBu indicate they cannot find root. I deleted all the root apps and tried reinstalling root via adb which completed successfully, but the same outcome with all the root apps. So I'm not sure if I'm still really rooted as Root Checker claims, or not.
EDIT: I just saw that I have 2 "Knox Settings" apps. Clicking on either returns, "Unfortunately, Container Agent2 has stopped."
use the odin from the stock firmware thread to flash it again. if it fails you can flash the u firmware and then the stock again. then you have to use a different odin if you want to flash the root api file the one you flash the firmware with wont work. also there is help in one of the threads about fixing the volte problem so you dont have to turn it off to get calls. i didnt have to do it as using the odin i mentioned fixed it for me when i came from the u firmware.
NovaEDM™ said:
Hello, my SM-G935A is rooted, and I have 2 issues with it. Firstly, I'm unable to receive texts or phone calls (I can send them), and I've tried a factory reset and I even got a new SIM, but nothing worked. I think if I flash stock firmware, it might fix the issue. Second problem, when I go into download mode and select my AP in Odin and press start, my phone gets an error and Odin freezes at Initialization.
Any help would be appreciated. I would prefer to fix the texting issue, as I don't want to return the phone to ATT. In either case, the Odin issue needs to be fixed
Click to expand...
Click to collapse
I was having the exact same problem you had with Odin. It seemed I was able to flash stock firmware using this version of Odin: http://www.mediafire.com/download/2t2sjqxtogbkafk/odin_3.12.3.rar
rob219 said:
use the odin from the stock firmware thread to flash it again. if it fails you can flash the u firmware and then the stock again. then you have to use a different odin if you want to flash the root api file the one you flash the firmware with wont work. also there is help in one of the threads about fixing the volte problem so you dont have to turn it off to get calls. i didnt have to do it as using the odin i mentioned fixed it for me when i came from the u firmware.
Click to expand...
Click to collapse
did you have any problems with the u version of the s7 edge firmware, like the fingerprint scanner not responding? i am on that version and cant get any odin version or any version of s7 edge g935a firmware to flash, tried unrooting and was forced to use the U version of the s7 edge firmware, everything works except the fingerprint scanner, cant get back to full stock firmware, need help!
im having the exact same problem, when i put my phone into download mode and flash the stock at&t firmware, Odin get stuck in "initialization" and my phone screen displays and error message.
Same stuff was happening to me, I went back to stock and took the update. When your phone stops working as an actual phone, it's time to roll it back.
I played with it for a week and my phone was so freaking hot (with hot weather) equals a wait and see if this gets more stable in the near future. I did use the Odin 3.12.3 mentioned by King James III. Honestly, I did so many things to get it back to stock I forget what actually worked (it was the wee hours of the morning and I was spent). Don't give up guys, it will and can work.
edit: It may be as simple as not right clicking Odin and running it as Administrator.
nicetucu said:
Same stuff was happening to me, I went back to stock and took the update. When your phone stops working as an actual phone, it's time to roll it back.
I played with it for a week and my phone was so freaking hot (with hot weather) equals a wait and see if this gets more stable in the near future. I did use the Odin 3.12.3 mentioned by King James III. Honestly, I did so many things to get it back to stock I forget what actually worked (it was the wee hours of the morning and I was spent). Don't give up guys, it will and can work.
edit: It may be as simple as not right clicking Odin and running it as Administrator.
Click to expand...
Click to collapse
I used Odin_v3.12.3_Patched_SHA256 to flash the 935U Firmware then used Odin3_v3.11.2 to flash the June Firmware release.
Folks I initially tried to root my phone *SM-G935F* using Odin and a CF hero2lte file. The flashing was all good to go with a green pass. Then upon rebooting the phone got stuck on the Samsung logo boot screen with red words at the top that said **Recovery Is Not Seandroid Enforcing**. This being the case all I was able to get into was (Download Mode). I tried to do the samething a few times and gave up after no successful attempts and the phone not being able to successfully reboot.
Fast forward to present I downloaded the phone's firmware which was a zip that contained 4 files (5 total actually because there was another CS file in the event that you wanted to preserve your data etc.). I loaded all of the files in Odin and made an attempt to flash the phone again however it got stuck on *System* and never go to Green *Pass*. So I figured I would try it a couple of more times in case Odin or something just got hung up on the first try. Any how that wasn't the case.
Now with the above being said what did change is when I would try to reboot into *Download Mode* again it said something along the lines of Emergency Smart Switch Recover. I downloaded Smart Switch onto my computer and went through the specific steps to try to Recover the phone using Smart Switch. Now after it was all done I got to the blue screen with the Android and it said *Erasing...* then the phone booted up and its now stuck at the Samsung animation screen. This being said as of current I can now access *Download Mode* and also boot into the black screen or *Recovery Mode* I think its called where I can reboot the phone through a bootloader, power off, factory data wipe / reset, etc etc.
The above being said I have tried the factory reset / wipe. The reboot in bootloader, reboot phone, all with no success.
Also would like to add that before doing all of the above I forgot to tick *USB Debugging* in Developers Mode when the phone was in its normal state. I must also mention that all of this was a first for me and I looked at doing so to try and recover lost data on my phone. Also wanna add that I am not too familiar with ADB or twrp or how to mess with any of that stuff given the limited access I have to my device because it can no longer bootup like it normally would.
I'm currently at a lost of words as to what I can do next as I am out of ideas and could really use some help. I would also be more than happy to donate a little to anyone who is able to help me boot my phone back up and get things back to normal.
Any and all help would be greatly appreciated.
Folks please disregard my post above as I was finally able to figure things out and get my phone back to its factory state. Thanks.
Hydranize said:
Folks please disregard my post above as I was finally able to figure things out and get my phone back to its factory state. Thanks.
Click to expand...
Click to collapse
Bro would you tell pls , what you did to restore. Thanks
shah22 said:
Bro would you tell pls , what you did to restore. Thanks
Click to expand...
Click to collapse
After me not being successful with the root or with flashing the stock OEM firmware using Odin the phone would get hung up in download mode and the only difference when it would go into download mode it would say to use SmartSwitch Emergency Recover which is what was used and that fixed the issue and the phone rebooted completely fine.
However the above being said I honestly still feel the phone has some small minor issues that I did try to resolve all with no luck. First off when loading to my home screen the icons, and clock, etc etc take about 2 or 3 seconds longer for them to appear on screen than it used like when the phone was new out of the box.
Other thing to note is for some odd reason this issue was thought to be worked out by just booting into recovery mode and doing a factory reset from there, wiping the cache, etc etc. Well this also didn't solve the issue and for some odd reason when performing this the phone didn't reboot on its own.
Basically how it should be normally is after you select that you want to do a factory reset, wipe cache, etc etc, the phone should normally reboot and go through the entire process by itself, however this was not the case. The phone instead went back to the recovery screen and I had to select reboot rather than it normally rebooting on its own.
I've honestly given up on things and given that it is in working order with just a few small minor hiccups I've decided to give the phone to a family member which they plan to use as trade-in credit towards a new Galaxy Note 8.
That being said I will always have a soft spot for the S7 Edge being it was my first smartphone after I had bought a Sony Xperia Z during the same year but returned it the day after because what was to me being poor quality of the Sony phone.
Hmm, looks strange bro , your phone didnt worked after flashing stock rom with odin , and this is the last resort , but you said it was normal before you tried to root , so i guess it was still a software issue other than some hardware problem due to software , but anyways wish you good luck in future , another thing is that my s7 edge has also a very poor build quality , has front camera issues , paint peeling around usb port , wifi issue and high battery degradation , but that happens i guess with today's phones
The version of Odin I used was v3.10.6. I had tried the most current version and a few others, and from the get go for whatever reason this was the only version that would actually pickup the phone being added. Well wait hold on a second the other version would say added when the phone was in but when hitting start nothing would happen, even after waiting an extensive amount of time, also note that the com was highlighted that blue ish color indicating the phone was being recognized by Odin but once again for some odd reason it was only version v3.10.6 that carried out the process of my root attempt and also the attempt I made flashing the original firmware on it.
As for quality the phone had no paint chip or peeling, neither the silver aluminum frame around it either. The build quality was beautiful and up to par with mine. I had a soft spot for my S7 Edge also because it was in the white color which at the time of purchasing was a bit more scarce than the other colors. I purchased the phone from an Amazon.com seller, and during that time I also purchased 2 others from other Amazon sellers but returned those because they had carrier animations for them that were Band LTE or Brand LTE, whatever its called.
This one had no carrier animation upon boot and turned out to be a UK Nougat model. Haven't really seen or came across another one since that would be from a trusted seller or source. Nowadays you never know what you're getting both on eBay and Amazon from these third party sellers.
Yeah thats really strange with odin , its good that you dont have quality issues which struck heavily on me , but yes everyone should be quite careful when ordering online and only should do with trusted resellers
Hydranize said:
Folks please disregard my post above as I was finally able to figure things out and get my phone back to its factory state. Thanks.
Click to expand...
Click to collapse
I'm facing the same problem buddy. Could you pass me the process for the recovery that was used?
vini3237 said:
I'm facing the same problem buddy. Could you pass me the process for the recovery that was used?
Click to expand...
Click to collapse
What phone are you having the issue with and what are you using that caused the issue? I can possibly try to help you out if I know a little more about your situation and device.
Hydranize said:
What phone are you having the issue with and what are you using that caused the issue? I can possibly try to help you out if I know a little more about your situation and device.
Click to expand...
Click to collapse
Phone is SM-G935FD
I do not know what caused it, I already got the celuar so, in status it says Custom.
I already tried to blink for odin 3 different Stocks and the same thing continues.
When I got it it could not access the recovery mode, only the download mode was accessible, after flashing the Brazilian Stock 6.0.1 I was able to access recovery mode.
The phone turns on, and hangs at boot, Samsung logo, restarts and stays in infinite looping.
Can it be Hardware?
Try to flash the original Firmware for it, make sure the Firmware is the one specific to that model, download it and load all of the Firmware files into Odin.
Hydranize said:
Try to flash the original Firmware for it, make sure the Firmware is the one specific to that model, download it and load all of the Firmware files into Odin.
Click to expand...
Click to collapse
Ok now i think what was the problem , you didnt enabled usb debugging , and for flashing with odin its a must ! , for guys who want to flash firmware using odin .. please enable usb debugging in developer options or you will have much issues and may also brick your phone , so if you dont want to enable usb debugging or developer options , just use samsung smart switch on pc to flash your firmware.
Yeah that was my issue was I had OEM Unlock checked off and one other thing in Developer Options and forgot to enable USB Debugging leaving me stuck in the process when the phone couldn't reboot normally after the flash attempts. But yeah SmartSwitch Emergency Recovery should definitely be able to fix and resolve the issue if the phone can't reboot normally.
Hi All,
So, I have spent 2 days trying to get my Galaxy s8+ back to normal. However, I seem to only have made it worse. It all happened when I decided to change the /data partition from ext4 to another format and then back again to get the /data partition to mount in TWRP after flashing Pascal Rom. However when I rebooted, nothing worked, no boot up screen, no recovery, no life, but all I could get was download mode. It then must of froze up after another restart and I couldn't get anything for 12 hours or so.
The next step I tried once i got download mode again was to flash stock firmware for the G955F, I can't remember the version of this firmware, but I still had nothing change. So then i flashed the latest firmware from SamFirm's downloading client, which was G955FXXU2CRF7 - Australian Optus Branded Firmware (OPS). I was able to get as far as the "hello start screen" and then my phone restarted, it then tried to upgrade my system again, then started "erasing" and then it rebooted and I still had the same issue, nothing but download mode and still no recovery, it still wouldn't turn on. So I flashed the latest International/Unbranded Australian firmware (XSA) - G955FXXU3CRGH, still the same result. I now can't go back to the OPS version of firmware because I get the Check error with the bootloader (since it's a more recent version), so I can't go backwards. I also can only flash "Official Binaries" now. Oh and to make things worse, I read that Odin Option "Nand Erase" just erased user data, so I thought I might as well try it, and as a result, I now can't flash even the (XSA) firmware because of ODIN failing and I now have an "An Error has Occurred while updating the device software. Use the emergency recovery function in the smart switch PC Software.". I am a bloody idiot :good: . Oh, I have tried multiple versions of Both Samsung Kies & Smart Switch (Which both had the option for "recovery & initialisation"), however, I get a message that my device is unsupported after adding in my device model and S/N. I tried a PIT file and then found out it's now included in all the latest firmware img files.. so yeah lol. Fun times. Soooo I feel like I am out of Options, nothing I do is working. The worst of all this is my wife is not happy haha which means after years of tinkering with android phones (flashing custom ROMS, Kernels, Root Solutions, e.c.t ), this may be the end of the road for me if I can't fix this phone. I really hope this thread isn't true too : https://forum.xda-developers.com/galaxy-s8+/help/sm-g955fd-access-download-mode-t3748228
So Please, someone help me out if it is at all fixable even if it requires opening the phone up lol.
The stats i have on download mode are the following:
RMM State as Prenormal
OEM Lock: OFF
FRP Lock: OFF
CARRIER_ID: OPS (which is super weird because it only accepts XSA to be flashed :S )
Secure download: Enabled
System Status: Custom
Warranty Void: 1
Current Binary: Samsun Official
If you need more, just let me know.
Ok, quick update: I have got rid of the error that I mentioned. I managed to flash XSA firmware again, it went to the blue Andriod is updating the system screen, then started "erasing" then rebooted and nothing again, still only download mode available. Nothing happens when I try to turn it on or try recovery mode.
This firmware you mentioned XSA - G955FXXU3CRGH i would double check. As far as I know Australia doesn't have a version 3 bootloader yet whether unbranded.telstra or Optus.
Quick Update: Maybe Fixed now!
Even though no one has replied yet, as it's only been an hour or so. I just wanted to let anyone else know who is experiencing a similar issue in the future on how to possibly fix it.
This was a real nightmare, however quick disclaimer, I am not responsible for any damage incurred to your device/property by following my instructions.
So the way I have fixed it, is I flashed the AP file only (from the firmware zip i had downloaded from SamFirm) with "Auto Reboot" Off. When ODIN finished, I held the Vol Down + power button, to reset it. It gave me a blue "No Command" Screen, I then waited and it then went black and the recovery screen appeared. I cleared the cache, rebooted to bootloader, which it didn't turn back on, so I left it because I thought it was the same thing. Came back 10 mins later and turned it on (or hard restarted, can't remember) and it worked. It booted!
I did soon learn it looks like it was having a charging problem because it had no charge and kept telling me there was water in the port (even though it was dry), I restarted it again after putting it on a wireless charging pad and it is seeming fine so far with the USB charger. So big note to anyone in the future, that it could be possibly bugging out with charging as well if you can't get it back on. I did have the device tell me here and there the last two days that there was water in the port when it was off. So kinda weird.
I know this all sounds a little hocus pocus, superstitious almost, but hey, my phone is working, so maybe replicating my actions may just help lol. :cyclops:
spawnlives said:
This firmware you mentioned XSA - G955FXXU3CRGH i would double check. As far as I know Australia doesn't have a version 3 bootloader yet whether unbranded.telstra or Optus.
Click to expand...
Click to collapse
Oh right, well, I did hear that SamFirm is not supported anymore, as that's where that firmware came from. Maybe it's dishing out incorrect firmware now? Possible the structure of where ever it is getting its firmware from (pretty sure it's pulled from samsung) has possibly been altered?
Just for reference I use www.updato.com for downloading firmware it is usually up to date. No reference to the firmware you mentioned (not for Australia anyway)
The screenshot I took: Imgur link:
https://imgur.com/a/lqyzWW7
Interesting I'll keep a lookout for it. Still on nougat 7.0 (XSA) no plans to upgrade yet until some issues are fully resolved ( out of beta stage that is ).
spawnlives said:
Interesting I'll keep a lookout for it. Still on nougat 7.0 (XSA) no plans to upgrade yet until some issues are fully resolved ( out of beta stage that is ).
Click to expand...
Click to collapse
Yeah, it's seeming to work now, but my fast charge isn't working. However, my other oreo ROM didn't work with fast charge either. So i am unsure if it is my phone or an orio bug :/ lol
Well at least you got it working and not using as a door stop
that was really sad story man.....
spawnlives said:
Well at least you got it working and not using as a door stop
Click to expand...
Click to collapse
Yeah haha, so glad it's not a door stop haha
Got a slight problem here.
First of all how do I find out the original network / carrier the phone was on?
I stupidly went and flashed the XSA (Australia) firmware without making note of the original carrier. Is there a way I can find out?
Secondly every time I boot the phone up it does a boot loop at least 4 times before it gets into the system.
Any ideas on this?
Thanks
G900i
My device came with Telstra firmware. I have flashed XSA, Optus, Vodafone, Spark NZ and India.
No problems.
Did you use Odin to flash your firmware?
What country are you in?
Hi
Yes I am in Australia and yep I used Odin.
It seems that even flashing TWRP the same issue I encounter but the strange thing is, although it shows up 'Recovery booting' and shows the Samsung Galaxy S5 splash logo I can still press buttons on the phone and I know this because it vibrates. Its almost like TWRP is there and is open in the background but its just not displaying at all. I have honestly tried so much.
I have downloaded (Using Sam Firm) the latest XSA and even found the PIT file to re partition but that made no difference.
The phone has had a total of around 7 LCD screens installed which came from various sellers in China. Due to the constant connection and disconnections of them I would say it may well be responsible for this issue as it has caused no doubt some considerable amount of stress to the motherboard. Maybe I am wrong I am just not sure.
It is a bizarre issue. I have never come across it before.
Standard stock recovery is also behaving the same way... I am getting, in blue, on the top of the screen 'Recovery Booting' then thats it... just that... waiting for ages and nothing happens but I am pretty sure that it is actually open behind the message which says 'Recovery Booting'
The whole things a bit of a mess.... When starting up the OS normally it takes around 5 bootloops for it to actually load up lol
Wow!! That's just crazy. Sounds like your device might have seen better days.
Occasionally I think its good to take the phone back to kitkat then to MM before twrp and custom roms.
I currently run klte version of /e/ pie ROM on my device which works very good. Un-Googled so my tired battery lasts better.
Best of luck with your problem.
Happy New Year mate.