Related
http://www.datafilehost.com/d/59efbc15mfastboot with custom Recovery Link
http://www.datafilehost.com/d/bf3a2c6d
Super SU
http://www.datafilehost.com/d/bab6821a
insure you have Unlock Bootloader if aren't see the Post by Lucas
http://forum.xda-developers.com/moto-g-2014/general/wip-unlock-bootloader-moto-g-2nd-gen-t2875728
After unlock Bootloader
1. Put Super SU in Internal Storage
2. Extract Rar file in pc
3. In Folder Shift+Right click Of mouse and Start Command Mode
4. Enter Command "mfastboot Devices" And see your serial No. of device
5. Then next Command "mfastboot flash recovery twrp-2.8.3.0-titan.img" Done
6. Next Command "mfastboot reboot"
5. Then Reboot in Recovery and Flash Super Su
done !!! See super Su in Device
My moto g2 stuck on bootloader unlock warning after rooting
My moto g2 stuck on bootloader unlock warning after rooting
Follow the instructions here instead:
www . gammerson . com /2015/11/how-to-root-moto-g2-on-marshmallow. html
(remove spaces from link, as I'm not permitted to post an actual link)
1st boot take time after unlock bootloader .. if take more
then try to reset from recovery when Power off your device
-for recovery first press volume down button during power button
-select recovery in option
-when android logo comes press again both volume button during press power button and wipe data reset and wipe cache partition too
if you want remove unlocked bootloader logo
-Make sure you have setup ADB and mfastboot on your PC. (Download from above)
-Download the logo file and extract the zip file to get the logo.bin file. Transfer the logo.bin file to some place you can track it easily. Its better if you use the folder where you setup the mfastboot.
-Power off your device and keep it unplugged from your PC.
-Boot into bootloader. To do so, press and hold volume down and the power button for 5-6 seconds.
-You will see the bootloader screen. Now plug in your device to the PC.
-Navigate to the location of the logo.bin file. While the folder with the logo file is open, hold shift on keyboard and right-click on an empty space and select “Open command window here” option to launch a cmd window.
Now type the following in the command prompt to get a code
mfastboot flash logo logo.bin
Now type the following in command prompt to reboot.
mfastboot reboot
Once you reboot, you will no longer see the bootloader warning as it has been replaced with the Motorola logo. You can choose a custom image you like but be sure it is in .bin
link for logo file
https://www.datafilehost.com/d/TekaWiCcHE
Root Failed?
I followed your steps and after I flash recovery, It says boot failed when i try to boot in recovery. It says failed to boot?
Rushaan9912 said:
I followed your steps and after I flash recovery, It says boot failed when i try to boot in recovery. It says failed to boot?
Click to expand...
Click to collapse
well make sure that you have unlock bootloader,
are you able to start fastboot ?
then try this commands
mfastboot erase cache
mfastboot erase userdata
mfastboot reboot
Locker49 said:
well make sure that you have unlock bootloader,
are you able to start fastboot ?
then try this commands
mfastboot erase cache
mfastboot erase userdata
mfastboot reboot
Click to expand...
Click to collapse
Tried it. It formatted my phone, Stilll wont root. WHenever I select REcovery it says "Failed to boot"
Rushaan9912 said:
Tried it. It formatted my phone, Stilll wont root. WHenever I select REcovery it says "Failed to boot"
Click to expand...
Click to collapse
Tried to flash recovery by fastboot ?
still face problem then you need to flash your stock rom
Instruction to Restore Stock Firmware on Moto G 2014
See the Post by @bhu999
http://forum.xda-developers.com/moto-g-2014/general/restore-to-stock-original-motorola-t3155774
first you needto Flash lollipop(link below) then in recovery you upgrade MM
https://docs.google.com/uc?id=0B665WEdcrNV2dnpDYjdJaTh5aGc
marshmallow (indian) Dual sim
https://drive.google.com/file/d/0B7BRotdWEAc5TXJQc091Vk5RQU0
https://drive.google.com/file/d/0Bw0NmnatfFOxVEotMFZlMkQzZkk
Kit-kat to MarshMallow
https://mega.nz/#F!Q9YHCQzY!dgyvAJ8eNA3t7az4vizwOQ
Locker49 said:
Tried to flash recovery by fastboot ?
still face problem then you need to flash your stock rom
Instruction to Restore Stock Firmware on Moto G 2014
See the Post by @bhu999
http://forum.xda-developers.com/moto-g-2014/general/restore-to-stock-original-motorola-t3155774
first you needto Flash lollipop(link below) then in recovery you upgrade MM
https://docs.google.com/uc?id=0B665WEdcrNV2dnpDYjdJaTh5aGc
marshmallow (indian) Dual sim
https://drive.google.com/file/d/0B7BRotdWEAc5TXJQc091Vk5RQU0
https://drive.google.com/file/d/0Bw0NmnatfFOxVEotMFZlMkQzZkk
Kit-kat to MarshMallow
https://mega.nz/#F!Q9YHCQzY!dgyvAJ8eNA3t7az4vizwOQ
Click to expand...
Click to collapse
Is it possible that this doesnt work on my phone because I have the 4G-LTE model?
Rushaan9912 said:
Is it possible that this doesnt work on my phone because I have the 4G-LTE model?
Click to expand...
Click to collapse
i uploded for moto g2 2014 (lte)
Rushaan9912 said:
Tried it. It formatted my phone, Stilll wont root. WHenever I select REcovery it says "Failed to boot"
Click to expand...
Click to collapse
Try using this SU as its the only one that has worked for me
http://forum.xda-developers.com/showpost.php?p=67670718&postcount=2
The issue is in the SuperSU updater script, which can't detect the system and is trying to install root in system mode (it should use systemless mode)
For those users who are stuck at bootloader logo after flash supersu, is necesary to reflash stock rom and flash this SuperSU (I've edited the updater-script to force systemless install)
After flash this SuperSU (updated to 2016-09-01), all updates can be installed directly from the store
Stuck at the start page
The root was done,but while rebooting the phone,the phone stuck on the unlock bootloader window and nothing happens.If anybody had the same problem please tell me how to repair it.
Locker49 said:
http://www.datafilehost.com/d/59efbc15mfastboot with custom Recovery Link
http://www.datafilehost.com/d/bf3a2c6d
Super SU
http://www.datafilehost.com/d/bab6821a
insure you have Unlock Bootloader if aren't see the Post by Lucas
http://forum.xda-developers.com/moto-g-2014/general/wip-unlock-bootloader-moto-g-2nd-gen-t2875728
After unlock Bootloader
1. Put Super SU in Internal Storage
2. Extract Rar file in pc
3. In Folder Shift+Right click Of mouse and Start Command Mode
4. Enter Command "mfastboot Devices" And see your serial No. of device
5. Then next Command "mfastboot flash recovery twrp-2.8.3.0-titan.img" Done
6. Next Command "mfastboot reboot"
5. Then Reboot in Recovery and Flash Super Su
done !!! See super Su in Device
Click to expand...
Click to collapse
Does this work on the XT1064?
bootloader is unlocked successfully but it is showing no command while trying to superuser in recovery option with a android bot lying down with an exclamatory mark on it in red background, what does it mean?
can moto g2 support VOLTE?
Facing same issues while trying to flash su. Result: stuck at bootloader screen
After running successful "fastboot flash recovery twrp.IMG " when i select recovery option in my moto g(titan) an error occur that is"boot failed"
How can i fix it please help asap?
hi guys
im using zenfone 5 which was kitkat previously then i updated to lollipop via sideload adb but now my device is bricked and when i try to sideload new firmware it shows the following command with error
E: failed to mount / cache (no such file or directory)
E:cant open / cache /recovery / logs
E:cant open / cache /recovery / logs
E:cant open / dev/block/mmcd1k0p4(permission denied)
when im using these commands after entering into normal boot mode
(before executing commands)
[IMG="normal boot mode in lollipop"]
1)fastboot flash fastboot fastboot.img
2)fastboot reboot-bootloader
im supposed to get this screen after executing above commands
[IMG="droidboot mode"]
but im not getting this screen guys.
im again back to this screen only
[IMG="normal boot mode in lollipop"]
sorry guys this post doesnt allow me to link images because im new to this site
i cross checked with my friends mobile its working flawlessly
help me out from this isssue bro
thank you
mine too
Any expert please help
I need to know whether your partitions are okay or not. Please answer my questions below:
1. What's the model of your device? T00F/T00J?
2. Can you reboot into fastboot?
3. What was the last thing you did to it before bricking?
4. Does it flash the fastboot.img file successfully?
5. Which firmware were you using before sideload push? I mean when the device was fine, what was your firmware version?
6. Which version you were trying to push while you bricked it?
a8962383 said:
I need to know whether your partitions are okay or not. Please answer my questions below:
1. What's the model of your device? T00F/T00J?
2. Can you reboot into fastboot?
3. What was the last thing you did to it before bricking?
4. Does it flash the fastboot.img file successfully?
5. Which firmware were you using before sideload push? I mean when the device was fine, what was your firmware version?
6. Which version you were trying to push while you bricked it?
Click to expand...
Click to collapse
1. t00f
2. yes
3. i upgraded to lollipop which displays error that unfortunately stopped and i restarted thats the phone stucks at boot loop
4. no.it fails to flash the flashboot image
5. kitkat 2.21.44.540
6. tried all kitkats from 2.21.22.30 to 54 and lollipops also
error image
i dot imgur dot com/IrvGjbS.jpg
recovery
i dot imgur dot com/7UYyLnm.jpg
(replace dot with .)
thanks
I got same problem (solved)
I have advice for you according my experience.
My device is T00F/A500CG
I assume you can enter bootloader or recovery mode, your pc installed all needed driver to do command adb sideload.
1. Download official ZenFone 5 firmware from ASUS website. Just go to Google and type keyword "download ZenFone firmware".
2. Download firmware 5.3.3.3 and 5.2.2.2 (apply same SKU according your device). because my device use WW sku, so I downloaded firmware WW_5.3.3.3 and WW_5.2.2.2.
3. Place those firmware inside adb folder in your pc.
4. Go to recovery mode on your ZenFone 5.
5. Connect your ZenFone to pc using USB cable.
6. Select menu "apply update from adb" on recovery mode.
7. Open cmd at your adb folder.
8. Check whether your device connected or not by using command "adb device". Make sure your device listed as attached.
9. Flash your firmware 5.3.3.3 using adb sideload command.
10. At recovery mode, select clear cache and user data (optional).
11. Once again, enter menu "apply update from adb" at recovery mode and flash firmware 5.2.2.2 using adb sideload command.
12. Do clear cache and user data at recovery mode. Then restart your device. Its will take time to load operating system for the first time, so be patient. Once you done, your device will be running on kit Kat.
This is other way. If you still want to use lollipop on your ZenFone 5.
Follow the step above until step 10. Once it done, restart your device (it will take time for the first time). You will be on lollipop because firmware 5.3.3.3 itself based on lollipop. And of you want to use latest update lollipop (firmware 3.24.40.87) don't do adb sideload from firmware 5.3.3.3 or it will be fail at 54% and you need to repeat step above from step 1.
If you want to proceed to firmware 3.24.40.87, do this:
1. Download ZenFone assists (I recommend this tool).
http://forum.xda-developers.com/zenfone-5/development/zenfone-assist-t3401996
2. Place downloaded file in a folder and extract it.
3. Run the *.exe file. (Active internet connection needed for next step).
4. Activate "developer option" on your ZenFone, active USB debuging and then Connect your ZenFone using USB cable to your pc.
5. Click on "root" menu at ZenFone assists. ( application will download some file for first time usage).
6. When it done, click on " I'm on android" and your device will reboot and automatically enter fastboot mode.
7. When your ZenFone at fastboot mode, click on "execute" on ZenFone assists.
8. Done,reboot your device and if there is no super SU app installed, don't worry, your device has been successfully rooted. Check using root checker if you doubt that.
9. Successfully rooted, now use ZenFone assists to unlock your bootloader( use menu "unlock bootloader" at ZenFone assists). The processes will be similar
As process 5-7.
10. Install TWRP using ZenFone assists. Its also similar with process 5-7.
11. Download moded stock firmware 3.24.40.87 from here
drive.google.com/open?id=0B7Py5ad2aHwKMHRsZ1NJM0tfLTQ
(Source thread :http://forum.xda-developers.com/zenfone-5/help/how-to-revert-to-stock-firmware-t3303654)
This firmware is completely same as official firmware from ASUS, only changed in Meta.inf file so make it able to flash through TWRP.
12. Place downloaded firmware in your SD card.
13. Reboot your device to fastboot mode and enter recovery mode.
14. Your official recovery now replaced by TWRP.
15. Just touch "install from zip" menu at TWRP and select storage where you place the firmware. Do the flashing process, be patient and wait until done.
16. When its done, using TWRP wipe your cache and reboot your device. It will take time for first boot, be patient.
To restore your device all into normal (relock bootloader and replace TWRP with original recovery). Do this:
1. Enable developer option on your device then connect it to your pc using USB cable.
2. Open zenfone assists and select menu "relock bootloader". I assume you already familiar with this process.
3. Open downloaded firmware 3.24.40.87 and extract droidboot.img, boot.img, and recovery.img from inside the zip file and place them inside adb folder.
4. Reboot your ZenFone to fastboot mode, open cmd in adb device folder.
5. Flash fastboot using command fastboot flash fastboot fastboot.img
6. Flash recovery using command fastboot flash recovery recovery.img
7. Flash kernel using command fastboot flash boot boot.img
8. Enter recovery mode then wipe cache and user data (optional).
9. Or just reboot your device.
10. Done, enjoy.
Jagernout said:
I have advice for you according my experience.
My device is T00F/A500CG
I assume you can enter bootloader or recovery mode, your pc installed all needed driver to do command adb sideload.
1. Download official ZenFone 5 firmware from ASUS website. Just go to Google and type keyword "download ZenFone firmware".
2. Download firmware 5.3.3.3 and 5.2.2.2 (apply same SKU according your device). because my device use WW sku, so I downloaded firmware WW_5.3.3.3 and WW_5.2.2.2.
3. Place those firmware inside adb folder in your pc.
4. Go to recovery mode on your ZenFone 5.
5. Connect your ZenFone to pc using USB cable.
6. Select menu "apply update from adb" on recovery mode.
7. Open cmd at your adb folder.
8. Check whether your device connected or not by using command "adb device". Make sure your device listed as attached.
9. Flash your firmware 5.3.3.3 using adb sideload command.
10. At recovery mode, select clear cache and user data (optional).
11. Once again, enter menu "apply update from adb" at recovery mode and flash firmware 5.2.2.2 using adb sideload command.
12. Do clear cache and user data at recovery mode. Then restart your device. Its will take time to load operating system for the first time, so be patient. Once you done, your device will be running on kit Kat.
This is other way. If you still want to use lollipop on your ZenFone 5.
Follow the step above until step 10. Once it done, restart your device (it will take time for the first time). You will be on lollipop because firmware 5.3.3.3 itself based on lollipop. And of you want to use latest update lollipop (firmware 3.24.40.87) don't do adb sideload from firmware 5.3.3.3 or it will be fail at 54% and you need to repeat step above from step 1.
If you want to proceed to firmware 3.24.40.87, do this:
1. Download ZenFone assists (I recommend this tool).
http://forum.xda-developers.com/zenfone-5/development/zenfone-assist-t3401996
2. Place downloaded file in a folder and extract it.
3. Run the *.exe file. (Active internet connection needed for next step).
4. Activate "developer option" on your ZenFone, active USB debuging and then Connect your ZenFone using USB cable to your pc.
5. Click on "root" menu at ZenFone assists. ( application will download some file for first time usage).
6. When it done, click on " I'm on android" and your device will reboot and automatically enter fastboot mode.
7. When your ZenFone at fastboot mode, click on "execute" on ZenFone assists.
8. Done,reboot your device and if there is no super SU app installed, don't worry, your device has been successfully rooted. Check using root checker if you doubt that.
9. Successfully rooted, now use ZenFone assists to unlock your bootloader( use menu "unlock bootloader" at ZenFone assists). The processes will be similar
As process 5-7.
10. Install TWRP using ZenFone assists. Its also similar with process 5-7.
11. Download moded stock firmware 3.24.40.87 from here
drive.google.com/open?id=0B7Py5ad2aHwKMHRsZ1NJM0tfLTQ
(Source thread :http://forum.xda-developers.com/zenfone-5/help/how-to-revert-to-stock-firmware-t3303654)
This firmware is completely same as official firmware from ASUS, only changed in Meta.inf file so make it able to flash through TWRP.
12. Place downloaded firmware in your SD card.
13. Reboot your device to fastboot mode and enter recovery mode.
14. Your official recovery now replaced by TWRP.
15. Just touch "install from zip" menu at TWRP and select storage where you place the firmware. Do the flashing process, be patient and wait until done.
16. When its done, using TWRP wipe your cache and reboot your device. It will take time for first boot, be patient.
To restore your device all into normal (relock bootloader and replace TWRP with original recovery). Do this:
1. Enable developer option on your device then connect it to your pc using USB cable.
2. Open zenfone assists and select menu "relock bootloader". I assume you already familiar with this process.
3. Open downloaded firmware 3.24.40.87 and extract droidboot.img, boot.img, and recovery.img from inside the zip file and place them inside adb folder.
4. Reboot your ZenFone to fastboot mode, open cmd in adb device folder.
5. Flash fastboot using command fastboot flash fastboot fastboot.img
6. Flash recovery using command fastboot flash recovery recovery.img
7. Flash kernel using command fastboot flash boot boot.img
8. Enter recovery mode then wipe cache and user data (optional).
9. Or just reboot your device.
10. Done, enjoy.
Click to expand...
Click to collapse
how much time does it takes for first boot in kitkat (after flashing 5.3,3,3 and 5,2,2,2)
reply asap
thanks
RONUAA said:
how much time does it takes for first boot in kitkat (after flashing 5.3,3,3 and 5,2,2,2)
reply asap
thanks
Click to expand...
Click to collapse
At lease 10 minutes it will take for the first boot. Don't worry, stay cool.
How about without root,if same method can do?
My phone, the LeEco Le Pro 3 LEX727 ZL1_NA US model is on the latest EUI 5.8.021S. I am able to open the adb tools in command prompt and get my computer to recognize my phone with "adb devices", but when I go to the stock fastboot with the Chinese and English writing and use "fastboot devices" nothing shows up. I'm using the latest adb tools and am clueless as to what to do.
Unlock Bootloader - Le Eco Pro 3
If you are not seeing your phone ID in ADB
Did you enable enable Developer options, or chosen MTP?
Its possible that the Android driver driver is outdated, or just try another usb port, preferably in the back of the machine.
Go here to check a whole list of possible causes: https://appuals.com/android-phone-not-showing-up-on-pc/
More than you asked for:
Since you seem to be new to your Leeco phone and new to using custom roms, I am going to go ahead and answer your current question and provide you steps needed to move forward. No big deal, I just copy pasted my notes ( with a few edits)
First steps that you need to take:
1. You will first need to unlock the bootloader :
PHP:
https://forum.xda-developers.com/showpost.php?p=71566961&postcount=203
2. Install Twrp :
PHP:
https://twrp.me/leeco/leecolepro3.html
****** Scroll down to see: Fastboot Install Method (
3. Right now just use ADB. But for the future, I highly recommend that you buy an OTG drive: it makes the whole process a thousand times easier: They are cheap somewhere near $5 and worth ten times that
Unlocking the Bootloader
You can save your self alot of time by looking up how to give ADB system wide privileges: this will allow you to flash files without tying the directory path.
Mauronofrio created a tool called: "TOOL ALL IN ONE"" it's great, install it and check for updates.
PHP:
https://toolaio.tk
The all is one tool is excellent and you can use it to install everything if wanted.
I usually recommend it for novices that can use it to help with unlocking the bootloader and installing TWRP.
The tool will also update your copy of ADB, android Drivers and provide system wide privileges for ADB
LETS RECAP : Choose using the All in One Tool or the ADB Method
**********BEFORE DOING ANYTHING*******************
Make sure you have enabled the developer tools,
Turned on USB debugging
Authorized your computer on your device I.E: “MTP”
Make sure the All in One Tool can see your device
(*) Select your device from the drop down menu, then click check
(*) Choose to install drivers, and set ADB and fastboot privileges from advanced menu.
(*) First attempt to unlock, then check bootloader status
If you have a X727 you will need to flash : emmc_appsboot.mbn from this zip :
PHP:
https://androidfilehost.com/?fid=313042859668275431
Next, choose Recovery flasher and manually select your copy of TWRP
After you have received the success message, I recommend doing the rest of the install manually within Twrp Recovery.
(*) Reboot into TWRP and begin installation of your Rom, Gapps and Magisk.
Using the ADB Method
Install ADB/Fastboot tools on your computer
PHP:
https://wiki.lineageos.org/adb_fastboot_guide.html
1. Make sure you have enabled the developer tools,
2. Turned on USB debugging, and authorized your computer on your device “MTP”
3. Enter fastboot mode on phone (hold power and VOL -)
4. Make sure adb can see your device when you run "adb devices"
5. type: fastboot devices
6. fastboot flash aboot emmc_appsboot.mbn
7. Run { adb reboot bootloader } - No spaces (before/after)
8. Run { fastboot devices } to make sure you see your device
9. Run { fastboot oem unlock-go } to unlock your device temporarily
10. Run { fastboot oem device-info } to verify unlock status
11. Run { fastboot boot recovery_twrp-3.2.1-0-zl1.img }
12. 5. Reboot back to TWRP and begin installation of your Rom, Gapps and Magisk.
13. 6. If you wiped data, your device will now proceed to re-initialize itself as if from the factory
Concerning your device's storage,
When you boot into twrp you will see a message that states that the storage is encrypted.
*****************Important************************ ******************
Ensure that you have TWRP installed as the primary recovery
Ensure that you have TWRP installed as the primary recovery
Ensure that you have TWRP installed as the primary recovery
Ensure that you have TWRP installed as the primary recovery
To remove encryption you will need to format the storage
(Anyone who says otherwise has the X720 and not the X727)
You could also try to skip the formatting step. But you will very likely have permissions issues and get errors and you will eventually have to come back and format ( Again as long as Twrp recovery is install there is very slim chance of ever bricking your phone.
To format the storage
Go to Wipe, choose Format Data and follow the instructions.
This will erase all of photos , music, etc
If you wiped your data partition, you'll need to push the zip file to the newly formatted storage. - This is one BIG reason why using OTG is better. You can use Mauronofrio's "TOOL ALL IN ONE"" for pushing the ROM, Gapps, and Magisk to storage.
Root: You absolutely should root!
NOTE: If you have unlocked the bootloader and flashed TWRP to the recovery partition. But have not yet flashed a Custom Rom the OS will likely reset back to the factory recovery UNLESS YOU ROOT THE SYSTEM. Your device is still unlocked. But the recovery can be overwritten by the stock EUI system, so beware.
Installation of Rom, Gapps, Magisk
Boot into TWRP recovery
1. Go to "Wipe" and then to "Advanced Wipe".
2. Mark "Dalvik / ART Cache", "System", "Data" and "Cache".
3. "Swipe to Wipe" and proceed back the main menu.
4. Go to "Install".
5. Select the ROM zip file and then press "Add more Zips" and select the Gapps zip file, and then the Magisk file.
6. "Swipe to confirm Flash" and wait for some time.
7. After the flashing is finished, just reboot to system.
Finished!
If you need help or have a question message me, I would much rather help you with a successful install versus helping you unbrick your phone.
Thank you for your reply. I figured out the issue. Windows 10 updater wasn't auto installing the driver for some reason even though I have auto update ticked.
simpbrackets said:
Thank you for your reply. I figured out the issue. Windows 10 updater wasn't auto installing the driver for some reason even though I have auto update ticked.
Click to expand...
Click to collapse
You have manually install those drivers usually.
Sent from my LEX720 using xda premium
I have the same issue in Windows 10. All In One Tool sees my x720 in adb mode, but when I switch to bootloader, the phone is gone. Device manager then shows unrecognized android device. I have LTSB version of Windows, so maybe that's why it won't auto install the needed driver. Could anyone point out what kind of driver exactly do I need, so that I can install it manually?
I wanted to create a guide which is as simple as rooting a OnePlus 3T. I don’t know if it will work with the OnePlus 3. I’m not responsible for anything. You’re doing it on your own risk, so only do it if you know what you will do, now! It may brick your device.
This is the way it worked for me. I do not guarantee it will work for you!
READ THE WHOLE INSTRUCTIONS FIRST BEFORE YOU DO ANYTHING
What we do:
- Flash TWRP
- Flash an old version of OOS
- Enable dm verity
- Relock the bootloader
- Flash the latest stock rom
What you need:
- Computer (Windows 7 or 10)
- USB Cable
- about 1 hour of your lifetime
YOU WILL LOOSE ALL YOUR DATA - ALSO THE INTERNAL STORAGE WILL BE DELETED (pics, music and all the stuff stored there)
Download to your computer:
Latest TWRP for OnePlus 3T
https://forum.xda-developers.com/on.../recovery-official-twrp-oneplus-3-3t-t3543391
and
latest OOS from OnePlus for your 3T
http://downloads.oneplus.net/
THE USB DRIVERS MUST BE INSTALLED ON YOUR COMPUTER
Download to the phone:
4.0.2 OOS Stock rom (post #2)
https://forum.xda-developers.com/oneplus-3t/development/recovery-twrp-oneplus-3t-t3507308
Flash TWRP:
1. Start your phone in fastboot mode (don’t connect to your PC yet!)
2. Open CMD as Admin (Windows start-menu - type “cmd”, right-click, run as administrator)
3. connect your phone
4. rename the file to “recovery” (don’t type “recovery.img” manually, only “recovery”)
5. type command “fastboot devices” -> device will be listed
6. command “fastboot flash recovery C:\Users\...\recovery.img” (the path where it’s stored)
7. done -> boot to recovery
8. disconnect your phone - leave CMD open
Flash OOS 4.0.2
1. Go into TWRP
2. wipe “System, Data, Cache, Dalvik”
3. Install OOS 4.0.2
4. reboot into fastboot
Enable dm-verity:
1. connect your 3T when it’s back in fastboot
2. type in CMD “enable dm-verity”
3. done - keep CMD open and the phone connected
Relock the bootloader:
1. type in CMD “fastboot OEM lock”
2. Warning message on your phone will pop up -> choose “yes” on your phone by using the volume buttons to lock the bootloader (keep CMD open)
Update to the newest OOS via “sideload”:
1. VOL down to boot into recovery
2. choose “Install from ADB”
3. “Upgrade Android from USB?” -> “Ok”
4. rename the OOS zip file to "update"
5. type in CMD “adb sideload C:\Users\...update.zip”
6. done
7. reboot the device - it will take about 10 minutes, DO NOT INTERRUPT THE PROCESS
Finish
Take your time! Don't do it if you're in a rush.
Please give me feedback if it worked for you or if I have to change something.
enable dm-verity doesnt work
"enable is not recognised..."
chowchillacharlie said:
enable dm-verity doesnt work
"enable is not recognised..."
Click to expand...
Click to collapse
Did you check if the device is listed in fastboot?
You can also try the command "disable" and then "enable"
Sometimes you may need to do it first, even if it's disabled
Thanks for your threat. I tried this but had to do a couple things differently.
I think enabling/disabling dm-verity works only with old firmware.
What I used:
* 4.0.2 firmware from this threat https://forum.xda-developers.com/oneplus-3t/how-to/firmware-modem-collection-flashable-zips-t3565535
* latest oneplus recovery and rom https://downloads.oneplus.com/
* the recovery can be downloaded from a link on the bottom of the rom download site.
I started with twrp and a custom rom.
You need usb debuging enabled and adb and fastboot installed
What I did:
* I did a Nandroid backup, and copied the sdcards content to my computer, because the following completely wiped my phone
"adb pull /sdcard /path/to/my/drive/"
* flash 4.0.2 firmware, with trp
enter adb sideload mode in twrp and
"adb sideload firmware.zip"
* fastboot flash oneplus recovery
"fastboot flash recovery recovery.img"
* using onplus recovery and sideloading installed latest oneplus rom
enter adb sideload and
"adb sideload oneplusrom.zip"
* did a factory reset in oneplus recovery and cheked if my phone would boot
* entered fastboot mode
"fastboot oem disable_dm_verity", then "fastboot oem enable_dm_verity"
"fastboot oem lock"
after that my phone got wiped again, and the next boot took a long time
Then the phone was completely stock
Wanted to post to say thanks to roor7 and WhataHulk - had a rooted 3T I wanted to sell following an upgrade (best price requires the phone to have no sign of root!), and this was the only method that worked for me to enable dm-verity.
As a quick note, I followed roor7's guide, but got the same error message as chowchillacharlie. After sme playing about I found the simplest soultion was using the CMD line provided towards the end of WhataHulk's guide, i.e. - "fastboot oem disable_dm_verity", then "fastboot oem enable_dm_verity". For me, roor7's guide swapping the type "enable dm-verity" in CMD with "fastboot oem enable_dm_verity" worked a treat.
Sorry if that is all incredibly obvious to most people!
Thanks again gents.
First : Sorry if the text is not perfect. I am french and it may have some mistakes ! I hope that an admin will edit my post in this case.
What you need:
1. Unlocked Bootloader and FRP
2. Download the last TWRP for our DUK : https://drive.google.com/file/d/1-LVwRb0JaXZMFFo-Jgg2_7VsUdMGzVFW/view
3. adb installed on PC
4. all-full-release.apk from https://github.com/topjohnwu/magisk_.../canary_builds
5. magisk-release.zip from https://github.com/topjohnwu/magisk_.../canary_builds
Install :
1. Copy/paste the twrp image in the folder of adb/fastboot
2. Go to your bootloader by plugging the USB cable and press VOL DOWN + POWER
3. From your Windows launch cmd.exe and type "cd C:\adb" (THIS IS AN EXEMPLE, DEPEND WHERE YOUR ADB FILES ARE)
4. Then type "fastboot flash recovery_ramdisk Honor8Pro TWRP.img"
5. Finally "fastboot reboot"
6. Unplug the USB cable and press VOL UP
7. In TWRP flash the magisk zip (You may have a problem with mount partition vendor, ignore it)
8. Reboot and install apk (You may have error application not installed, ignore it)
9. If the application is really not installed back to step 7)
This worked for me !
Hope this is the same for you
Would that be the same if I have android 9 with emui 9 ?
Thanks
loic2907 said:
First : Sorry if the text is not perfect. I am french and it may have some mistakes ! I hope that an admin will edit my post in this case.
What you need:
1. Unlocked Bootloader and FRP
2. Download the last TWRP for our DUK : https://drive.google.com/file/d/1-LVwRb0JaXZMFFo-Jgg2_7VsUdMGzVFW/view
3. adb installed on PC
4. all-full-release.apk from https://github.com/topjohnwu/magisk_.../canary_builds
5. magisk-release.zip from https://github.com/topjohnwu/magisk_.../canary_builds
Install :
1. Copy/paste the twrp image in the folder of adb/fastboot
2. Go to your bootloader by plugging the USB cable and press VOL DOWN + POWER
3. From your Windows launch cmd.exe and type "cd C:\adb" (THIS IS AN EXEMPLE, DEPEND WHERE YOUR ADB FILES ARE)
4. Then type "fastboot flash recovery_ramdisk Honor8Pro TWRP.img"
5. Finally "fastboot reboot"
6. Unplug the USB cable and press VOL UP
7. In TWRP flash the magisk zip (You may have a problem with mount partition vendor, ignore it)
8. Reboot and install apk (You may have error application not installed, ignore it)
9. If the application is really not installed back to step 7)
This worked for me !
Hope this is the same for you
Click to expand...
Click to collapse
[EDIT]
that did NOT work for me... but i could finally root my honor 8 pro with emui 9.0
i'm gonna make a post now , hopefully will help others !!!