Hi
Downloaded HUAWEI Y300 firmware (Y300-0100, Android 4.1, Emotion UI, V100R001C00B175, General Version)
from Huaweidevice.com
But dont know how to flash it.
Kindly help
regards
Hi,
same method as old models :
Check phone version / exact sub-model, here are three hardware versions of Y300:
1.Huawei Y300 (T8833) - TD-SCDMA / China Mobile
2.Huawei Y300-0000 (U8833) - WCDMA China Unicom
3.Huawei Y300-0100 (U8833) - WCDMA International
check version (product ID) with this code : *#*#1357946#*#* , dial button (green)
there is international version ROM - Y300-0100 at Huawei site, you probably downloaded it ...
- put "dload" folder from archive on formatted micro-sd card's ROOT
- put micro-sd card into phone
- start phone in download mode = Press the VOLUME UP and VOLUME DOWN key, and then press the
POWER key to power on the phone and enter the Software Upgrade Mode
(taken from upgrade manual - which is found in archive, pdf ... )
- wait for finish ...
p.s. if not accepting firmware - means it's not international version ....
b.r.
Alex
If you have "faild" at step 2/2 , you must "zero" your imei > flash rom > restore imei.
what is the latest firmware update for Huawei y300
what is the latest firmware update for Huawei y300? i have the software versio V100R001C151B165 is this the latest update?
please update
i backed up my imei but deleted the folder i try to backup again and it says its already backed up ??
How to restore Imei
I didn't understood woht ot restore my imei. Could you explain it completely?
HUAWEII Y300-0000 question
Hi,
I have HUAWEII Y300-0000 phone I've bought in china.
Managed to unlock it thanks to your manual.
It comes with ROM: Y300-0000V100R00C17B180 (Android 4.1.1).
The only problem I have is that sometimes when I try to dial I do not manage to establish call (the call is tried to be established and then disconnects). When this happens there is also problem in incoming calls. I manage to receive the incoming call but when answered the connection drops after several seconds.
My question is whether this is an issue you are familiar with.
If so, do you have any suggestions?
Are there any new ROMs for this version that maybe handle these kind of issues.
How can I install new ROM on already rooted phone?
Thanks in advance
tamirgz said:
Hi,
I have HUAWEII Y300-0000 phone I've bought in china....
Click to expand...
Click to collapse
Have the same problem - could I instal there soft for Y300-0100 after unlock bootloader?
Can you tell me how do I "zero" the Y300 IMEI? I have one that was left without system and now I can't flash the
HUAWEI_Y300_firmware(Y300-0100,Android 4.1,Emotion_UI,V100R001C00B175,Normal,05011FKA)
Now I can't revive my Huawei?
Thanks
OmenHTX said:
If you have "faild" at step 2/2 , you must "zero" your imei > flash rom > restore imei.
Click to expand...
Click to collapse
I tried the official one but the performance is very low:crying::crying::crying::crying:
Ram Expander on Huawei Asend Y300
I rooted my phone it works properly. Everything working fine. I just have have one problem that how to expand its ram. Plz tell me.
I tried with 2gb class 6 card with swalpt expander but it show nothing in it.
Huawei Y300 Ram Expander
Plz tell me how to expand ram of Huawei Ascend Y300.
babaphone said:
Hi
Downloaded HUAWEI Y300 firmware (Y300-0100, Android 4.1, Emotion UI, V100R001C00B175, General Version)
from Huaweidevice.com
But dont know how to flash it.
Kindly help
regards
Click to expand...
Click to collapse
hi there, i believe you can only flash the official firmware upgrades from a official ROM because when you check for upgrades to the firmware it gives you a option to install from local storage which i have yet to see in a custom ROM. in future i would always recommend a backup before installing any other ROM
hey someone flashed the official rom successfully?
zeroing imei
can you write how to zero imei code
flashing huawei y300. if you can upload any ctock or custom ro who i can install in
mobilexpert said:
Hi,
same method as old models :
Check phone version / exact sub-model, here are three hardware versions of Y300:
1.Huawei Y300 (T8833) - TD-SCDMA / China Mobile
2.Huawei Y300-0000 (U8833) - WCDMA China Unicom
3.Huawei Y300-0100 (U8833) - WCDMA International
check version (product ID) with this code : *#*#1357946#*#* , dial button (green)
there is international version ROM - Y300-0100 at Huawei site, you probably downloaded it ...
- put "dload" folder from archive on formatted micro-sd card's ROOT
- put micro-sd card into phone
- start phone in download mode = Press the VOLUME UP and VOLUME DOWN key, and then press the
POWER key to power on the phone and enter the Software Upgrade Mode
(taken from upgrade manual - which is found in archive, pdf ... )
- wait for finish ...
p.s. if not accepting firmware - means it's not international version ....
b.r.
Alex
Click to expand...
Click to collapse
if you can upload any custom or stock rom who i can install in stock recowery for huawei y300(recowery name is .android system recowery<3e>
huawei y300 flashing
OmenHTX said:
If you have "faild" at step 2/2 , you must "zero" your imei > flash rom > restore imei.
Click to expand...
Click to collapse
how to get or hack bootloader code if my phone is bricked.
or
if you can upload any custom or stock rom to install in stock recowery(i can go to recowery and i can force upgrade but fails at step 2/2).
recowery name is ''android system recowery <3e>''.
or if i can instal any custom recowery now i install rom trought this custom recowery.
WRITE ANY OPTION TO WAKE UP MY PHONE.
falshing huawei y 300
babaphone said:
Hi
Downloaded HUAWEI Y300 firmware (Y300-0100, Android 4.1, Emotion UI, V100R001C00B175, General Version)
from Huaweidevice.com
But dont know how to flash it.
Kindly help
regards
Click to expand...
Click to collapse
i install chainfire 3d and when i instaling driver my phone is shut down and i can wake up him from that it only show huawei ascend logo i can go to stock recowery and i can force upgrade but fail at ste 2 can you fix it
Unlockin Huawei Y300
babaphone said:
Hi
Downloaded HUAWEI Y300 firmware (Y300-0100, Android 4.1, Emotion UI, V100R001C00B175, General Version)
from Huaweidevice.com
But dont know how to flash it.
Kindly help
regards
Click to expand...
Click to collapse
http://www.youtube.com/watch?v=BBliIomdLOI
You can unllock bootloader like this see on video
Sigma-key app
Ateeq Rana said:
Plz tell me how to expand ram of Huawei Ascend Y300.
Click to expand...
Click to collapse
Search playstore I forget the excat name of the app. I used swapit(the name has changed now I forget the name) this uses your sd card as ram but do take note that the more u use your sd card the quicker it can go bad.
TWRP For innjoo Max 3 Pro LTE.???
Android Ver: 6.0
????????
Any thing
I just want to know how you upgraded your max 3 into 6.0
CorrM said:
TWRP For innjoo Max 3 Pro LTE.???
Android Ver: 6.0
Click to expand...
Click to collapse
please upload the tutorial of updating innjoo max 3 pro LTE from 5.1 to 6.0 (OTA or flashing).
my phone is 5.1 and doesn't detect via Spflash-tool.
Thank you.
vetfactor said:
please upload the tutorial of updating innjoo max 3 pro LTE from 5.1 to 6.0 (OTA or flashing).
my phone is 5.1 and doesn't detect via Spflash-tool.
Thank you.
Click to expand...
Click to collapse
First (Download):
InnJoo Max3 Pro LTE - Update V1.1.3 -> needrom.c o m/wp-content/uploads/2016/11/InnJoo-Max3-Pro-LTE-6.0-05. z i p
MTK USB Driver -> mediafire.c o m/download/ax14vw2odjn90h7/Mtk+driver+RepairMyMobile.in. z i p
Flashtools -> needrom.c o m/wp-content/uploads/2016/08/Pack-Flashtool-v5.1628.00.000. r a r
,,,,
Do The Same As This Topic
giveawaytricks.in/install-stock-rom-innjoo-max3-pro-lte/
Good Luck, If You Can Root after Update Pls Tell me,
Islam Nofl, Egypt
Hi,
I upgraded my innjoo max 3 pro LTE to Android 6 and instead of choosing “firmware upgrade” from Download tap in Flash Tool I chose “format all + download” which wiped off IMEI. Subsequently, I tried all the possible best to re-write IMEI back to the phone but all went in vain.
(1) I installed all the needed drivers for the phone yet my computer couldn’t make connection to the phone via many writer programs I had downloaded.
(2) I resulted to using apk app to write IMEI and most APKs require a device to be rooted and yet this device is resilient to rooting and the apk that doesn’t require a rooted device couldn’t have the job done either.
All what I want is being able to restore my IMEI back by rooting or not by rooting that doesn’t make a difference to me.
Please, I need help here
Dear good afternoon,
I have followed the forum daily and analyzed all the existing versions of update of ZenFone 2 for android 7.0 but I have many doubts on how to carry out the process.
Before I had a Nexus, in which I modified Rooms, Kernels, Bootloaders without problems, but now with ZenFone I'm not getting anything.
Someone could help me and tell me where I find all the processes to perform the bootloader unlock, root and install a custom android 7.0 room.
Here is my ZenFone model data.
ZenFone 2 Laser (ZE601KL)
Asus_Z011D Model
Android version 6.0.1
Configuration number MMB29P.WW_USER_21.40.1220.1853_20160818_060020715_201602190037
Kernel Version 3.10.49-gd173641 21.40.1220.1853 # 1
Baseband version 202c10_10.2.0_160802
Thank you in advance for your attention. Hugs.
Hi I am new to this so please do bare with my lack of knowledge
first things first I never had been in the P9 Lite Beta I brought the phone and I have never installed any roms or so on
my question is it seems my phone is branded to the Germany Telekom
that's where I brought it makes sense my question is I can not go away from the
firmware or can I go from there firmware to another firmware like the one you can download from there main site that is unbranded
why do I think my phone is branded is because I have tried the Update.app from the 27.03.17 I do the dial code and it restarts it starts goes to 7 percent and it cuts out
failed to install reboot phone and it goes back into the 6.0 Marshmallow
I am wandering how other people are able to install the B170/B171 update I know my Phone Model is (Huawei P9 VNS-L11) but the Phone Model is Huawei P9 LITE Vns-L31 ???
how are people in Europe to install the phone prove its the final code an not the beta since I am not able to update an may people are saying its finished and it being rolled in OTA
what do I have to do to remove the Telekom software and install a stock rom without it being locked preventing me from installing the update to 7.0 please replay thanks you and enjoy the weekend
[Current Build - VNS-L31C432B160 Current Number - VNS-L31 Current EMUI - 4.1.1 Android 6]
NEED EMUI 5 or Higher Please!!!
Hey, there would it be possible to get some advice and working links, please.
I spent the day sorting out by P9 Lite that I got off eBay after my P9 got busted.
First up was the FRP - Done (finally)
Then it was the bootloader (trickier) Thank you DC-Unlocker, Huawei call centre no help.....
The phone is now unlocked, TWRP and Rooted.
Now I need to get it on to Stock Rom that supports EMUI 5 before I can install or try most of the custom ROMs on here, the problem is the links that I've come across lead to Huawei official site that no longer works.
I can use B383 but as my phone is dual sim should I not be using B382?
Singel SIM
2017.07.21 VNS-L31C440B383 http://update.hicloud.com:8180/TDS/d...ull/update.zip [WORKING]
updatedatafull http://update.hicloud.com:8180/TDS/d...-L11_ee_gb.zip [WORKING]
Dual SIM - [My Model]
2017.06.08 VNS-L31C440B382 http://update.hicloud.com:8180/TDS/d...ull/update.zip [NOT WORKING]
updatedatafull http://update.hicloud.com:8180/TDS/d...-L11_ee_gb.zip [NOT WORKING]
So if anyone could shed some light on my next steps to update the P9 Lite so I can install custom ROM's I would be very grateful.
CcX85 said:
[Current Build - VNS-L31C432B160 Current Number - VNS-L31 Current EMUI - 4.1.1 Android 6]
NEED EMUI 5 or Higher Please!!!
Hey, there would it be possible to get some advice and working links, please.
I spent the day sorting out by P9 Lite that I got off eBay after my P9 got busted.
First up was the FRP - Done (finally)
Then it was the bootloader (trickier) Thank you DC-Unlocker, Huawei call centre no help.....
The phone is now unlocked, TWRP and Rooted.
Now I need to get it on to Stock Rom that supports EMUI 5 before I can install or try most of the custom ROMs on here, the problem is the links that I've come across lead to Huawei official site that no longer works.
I can use B383 but as my phone is dual sim should I not be using B382?
Singel SIM
2017.07.21 VNS-L31C440B383 http://update.hicloud.com:8180/TDS/d...ull/update.zip [WORKING]
updatedatafull http://update.hicloud.com:8180/TDS/d...-L11_ee_gb.zip [WORKING]
Dual SIM - [My Model]
2017.06.08 VNS-L31C440B382 http://update.hicloud.com:8180/TDS/d...ull/update.zip [NOT WORKING]
updatedatafull http://update.hicloud.com:8180/TDS/d...-L11_ee_gb.zip [NOT WORKING]
So if anyone could shed some light on my next steps to update the P9 Lite so I can install custom ROM's I would be very grateful.
Click to expand...
Click to collapse
Hello,
i will suggest you how to try to get emui 5,
but in order to do this you need stock recovery. Check how to HERE.
Check with inbuild updater if an upgrade is offered. If you find no update use Firmware
Finder to force the update. VPN method worked fine for me but i update my firmware when i already was on emui 5.
All infos are inside the app. Your device is dual sim so look for B370 full ota mf pv first and
if you don't suceed go for B370 full ota one... ( firmwares that ends with odd numbers are for single sim ).
Absolutely do not use firmwares ( C440 ) with different version of the region you are on ( C432 ) because of bricks..
How to start:
1 - Check with inbuild updater and if gives no results go to point 2.
2 - Use Firmware Finder to force the update.
3 - If you find a update with inbuild app or FF then stop, don't do it, you need stock recovery first.
Feel free to ask but i can reply 1/2 times in a week and anyway can't assure this.
Good luck !!
Cheers