Related
Hello, I ran into a problematic brick on my L5...nothing seems to work to unbrick it.
I followed the guides step by step using the KDZ updater and the appropriate firmware for my country, but it doesn't work.
How I bricked it:
I had CM10 installed and perfectly running for a month, so today I decided to attempt an overclock to speed the device up a bit.
So, I downloaded and installed the modded kernel, flashed it using CWM and rebooted the device. After that, the device just keep booting up, showing the LG logo and then a black screen.
Now, after trying to flash the old firmware after going into download mode it just stops on the LG logo with the flare (sun ray effect) spinning around the logo all the time...It's been like that for almost 30 minutes now. I attempted re-flashing it 3 times but nothing seems to work.
What do I do?
Thank you in advance.
It's bootloop. When I had L5 I had the same problem after flashing bricked phone via KDZ.
Do hard reset with key combination. It worked for me. Phone will boot up few minutes.
LeoFalto said:
Hello, I ran into a problematic brick on my L5...nothing seems to work to unbrick it.
I followed the guides step by step using the KDZ updater and the appropriate firmware for my country, but it doesn't work.
How I bricked it:
I had CM10 installed and perfectly running for a month, so today I decided to attempt an overclock to speed the device up a bit.
So, I downloaded and installed the modded kernel, flashed it using CWM and rebooted the device. After that, the device just keep booting up, showing the LG logo and then a black screen.
Now, after trying to flash the old firmware after going into download mode it just stops on the LG logo with the flare (sun ray effect) spinning around the logo all the time...It's been like that for almost 30 minutes now. I attempted re-flashing it 3 times but nothing seems to work.
What do I do?
Thank you in advance.
Click to expand...
Click to collapse
I was forced to do a hard reset...that sucks but it had to be done.
Thank you.
I have a worst brick, I was rebooting when my phone frozen at the shuting down page, so I took out the batterie, then when I tried to turn on .... nothing, not even lg logo, nor buttons lights, ... nothing, I can't even activate download mode to reflash it!!! what can I do???, does anyone had same problem before
please help me I'm really starting to freack
aeoros said:
I have a worst brick, I was rebooting when my phone frozen at the shuting down page, so I took out the batterie, then when I tried to turn on .... nothing, not even lg logo, nor buttons lights, ... nothing, I can't even activate download mode to reflash it!!! what can I do???, does anyone had same problem before
please help me I'm really starting to freack
Click to expand...
Click to collapse
i had the same problem with my l7 ... problem was solved in an authorized gsm service with jtag method...
but i will try to help u with this... Your phone is seen in device manager as unknown or lge android platform or adb ... ? if so, try with adb sdk tools...
nastase.alex said:
i had the same problem with my l7 ... problem was solved in an authorized gsm service with jtag method...
but i will try to help u with this... Your phone is seen in device manager as unknown or lge android platform or adb ... ? if so, try with adb sdk tools...
Click to expand...
Click to collapse
nop, it's like the device is dead,
Have you tried it:
Hold together volumn (-) + home button, then turn the power on
sorry for the delay, The phone was dead so I send it to the warranty and they send it to LG and then returned working so I just had to reroot it and update it again
so there is no solution to this brick???
aeoros said:
sorry for the delay, The phone was dead so I send it to the warranty and they send it to LG and then returned working so I just had to reroot it and update it again
Click to expand...
Click to collapse
Quote:
Originally Posted by breakercris
I've tried everything.
The phone simply doesn't connect.
USB\VID_05C6&PID_9008&REV_0000
This is what I get when I connect the phone by USB.
I just cant get into emergency, DIAG or emergency CS
KDZ the phone connects and then I get a message afterwards PHONE NOT FOUND.
everytime I install the drivers by LG support tool, it keeps giving me the option to install the driver, like I havent done it a hundred times over.
I think there should be a driver somewhere that can be installed but the only people that have this driver are LG tech's. So they can bill you after
send the phone in cause you rooted it. So the one billion dollar question is witch hero will find a way to unbrick this device. We only need a way
to get a driver to install and we are home free. Or maybe the only other option is throwing the phone for sale on internet for spare parts
HELP PLEASE HELP find a way to unbrick this phone. Believe me I flashed and bricked alot of different phones and there was a way out but in
with this phone it seems impossible!!
And there is no mode to put it in in because te volume buttons don't do crap, the home button also, the only time that the phone does show up is when windows tells me it has an unknown device that I for the love of god can't find a driver for. I tried SDK, the LG drivers, but no dice
Did you try emergency mode? (volume up + volume down + power button)
If not, see if you can enter it and then flashing your stock firmware with Software update [KDZ] 1.0.4.4 (KDZ-Flasher).
Hi, i want to fix a phone of my friend by flashing it with odin, but things go wrong, the phone after failing wont start or respond to any button, i dont know what to do, please any help would be appreciated
Samsung Galaxy J1 SM-J100H
Edit:
Thanks xEmre66 for your reply, unfortunately no, i think i break the boot image, the phone wont boot on download mode even if i use 300k jig, i think the only solution is to use an sd card filled with the boot image, but i dont find in website a solution like that.
I tryed many solution but no one work, please if someone have the some problem tell me.
Can you get into the DownloadMode? (ODIN MODE)???
Sent from my SM-J100H using XDA-Developers mobile app
---------- Post added at 08:58 AM ---------- Previous post was at 08:57 AM ----------
I have this phone but it is not my main phone but maybe I can help you.
Sent from my SM-J100H using XDA-Developers mobile app
i'm working on this problem..
i resolved,
share there
OSKCHAST said:
i resolved,
share there
Click to expand...
Click to collapse
Please can you share the solution ?, i cant fix the phone.
same problem here
I have same problem here, samsung j100h of my friend do not boot, i download odin and correct rom to flash i flashed device correctly, but device now is fully dead, display not start, black screen, my win10 not recognise device, now cant flash using odin and using sp_flashtool....
device respond at win10 when i push vol up + power but can't make anything
i try to install all drivers signed and unsigned from samsung and mkt.. nothing works any idea???
caseres84 said:
I have same problem here, samsung j100h of my friend do not boot, i download odin and correct rom to flash i flashed device correctly, but device now is fully dead, display not start, black screen, my win10 not recognise device, now cant flash using odin and using sp_flashtool....
device respond at win10 when i push vol up + power but can't make anything
i try to install all drivers signed and unsigned from samsung and mkt.. nothing works any idea???
Click to expand...
Click to collapse
You broke the boot image. I'm sorry but you hard bricked the device. I had this phone but it was terrible because of its touchscreen. Maybe I could help you. Send me a PM and describe how you really broke the device.
xEmre66 said:
You broke the boot image. I'm sorry but you hard bricked the device. I had this phone but it was terrible because of its touchscreen. Maybe I could help you. Send me a PM and describe how you really broke the device.
Click to expand...
Click to collapse
same in here. I flash original rom from sam mobile site and my samsung sm-j100h is bricked now. i flash using odin and everthing was ok and it was pass. but nothing happend later on, screen remains black and I don't know what to do.
or atleast tell me can I get somehow all data stored on phone, if yes how to do it
guys still nothing???
same problem guys i bricked the phone 2 days ago with the original firmware from sam mobile u.u i put my samusung j1 in download mode and with odin i done the reflash odin it was green and said me passed but then when i tried to turn on the phone nothing happened my phone is died hard bricked is there a guys something to do to repair him?
i got the same problem..
the phone was completely DEAD after i followed all the instructions here => https://www.youtube.com/watch?v=1T9fxno2s68
Please somebody help us..
Here's my thread => http://forum.xda-developers.com/android/help/help-sm-j100h-dead-power-flash-t3511894
Thank you very much..
im using sm j110h and i too flashed orginal stock rom via odin but unfortunately i forget to put the batteries on and i fonud that after that i got pass message only now the screen remaines black and not getting to download mode and not switching on. does anyone help me on this problem hope will get a solution thanks in advance
Gal J1 of sadness.... but still hoping
2 days ago a friend asked me to fix his J1 stuck in boot image. I gladly said yes for I've done it 4x already different units same model with satisfying results. This one is the exact opposite because after flashing with Odin and getting the Passed result, the phone didn't reboot. Actually it never booted right after that moment. System didn't recognize the phone not even a dim light or blink or any reaction from it even when plugged in a wall charger. tried all possible solutions even the galaxy tab procedure of total batt drain and so on. The firmware I got is from xda, J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware.zip, and I'm sure it's fine because I've used it already with good results...
Guys, any of you with a solution on this or any suggestions would be much appreciated... Thanks very much in advance!!! :fingers-crossed:
Chrisjopett said:
2 days ago a friend asked me to fix his J1 stuck in boot image. I gladly said yes for I've done it 4x already different units same model with satisfying results. This one is the exact opposite because after flashing with Odin and getting the Passed result, the phone didn't reboot. Actually it never booted right after that moment. System didn't recognize the phone not even a dim light or blink or any reaction from it even when plugged in a wall charger. tried all possible solutions even the galaxy tab procedure of total batt drain and so on. The firmware I got is from xda, J100MLDXU0AOB3_OLC0AOB5_v4.4.4_Repair_Firmware.zip, and I'm sure it's fine because I've used it already with good results...
Guys, any of you with a solution on this or any suggestions would be much appreciated... Thanks very much in advance!!! :fingers-crossed:
Click to expand...
Click to collapse
PM me pls and tell me how you flashed it etc.
Help
I have same problem,hard brick.Can anyone help?
somebody got solution? i did update by kies and now the phone is dead at all. i can use odin mode and also can using recovery anymore. hmm i think my problem come from the battery :crying:
kkq29 said:
somebody got solution? i did update by kies and now the phone is dead at all. i can use odin mode and also can using recovery anymore. hmm i think my problem come from the battery :crying:
Click to expand...
Click to collapse
Can you get into Odin Mode? If yes, flash the stock firmware of your region (here is a fast server which provides very fast downloads: fw.updato.com) If no, then you should change your battery as you're saying "it came from my battery" and try the first step again.
If it doesn't help as expected, then your phone is hard bricked and can't be repaired at all. The only solution would be changing the motherboard, but I would not waste my money on a low-end device motherboard and I would directly buy a new phone. :/
Regards,
xEmre66
If I am correct...
Then SM-J110H have Spreadtrum SC7727S
Here is Pinout for Direct eMMC...
https://postimg.cc/image/ul680l5jv/
This Pinout seems also to work with:
Code:
SM-G318HZ
SM-Z130H
I have leaked SM-Z130H PDF... where Instruction is inside to repair with tweezer... USB cable + Spreadtrum Tool:
Code:
[B]ResearchDownload[/B]
In theory something similar should be possible with SM-J110H...
I have at the moment only 1 problem... to create PAC file...
No idea from where I can get:
Code:
FDL1
FDL2
Best Regards
Edit 1.
Sorry, seems I was drunken...
It is sooo hard to find Posts or Threads about SM-J110H...
But it seems SM-J100H also Spreadtrum device...
xEmre66 said:
PM me pls and tell me how you flashed it etc.
Click to expand...
Click to collapse
PM me too please
My teacher phone has a same problem, hehehe.
same problem here. my phone got stuck up with samsung logo then i just dowloaded a firmware on sammobile and i flash it via odin at first it passed then my phone did'nt turn on anymore.
J100H / DD Finding Deadboot solution
Hi ... guys me too having this sort of problem and i found bad about samsung using 32bit - Spreadtrum SC8830A EMMC chipset here
Fix solution Not Found still! if i done i will tell you!
on = SM-J100H/DD --- corp =samsung yateley, uk
ok friend iam searching for Solution for 3days bt i found none= with a clue
It is J100H on serial port= SPRD U2S Daig (ComXX) usb says= SPRD COM Emumerator
this means - all sprd flashing been done on this 2 port only - in Miracle Box it says -
Scanning USB Serial port...
SU2Serial Port: COM64
Connecting to Phone,Wait..
Done.
Infor: SPRD3
Initialize boot19...
>>BootLoad Error. ID: 1
so my option is if we build a sprdp.bin and flash in AP(PDA) it will boot to Download mode
and dont ask me where is that file i dont no - if any one can provide a real backup pit.pit file
via phone to me i can find something and let u know it. Only from a alive phone J100H/DD
plz friends i need help any dumps or pit. and if any one has a alive J100H/DD please tell me.!
so i can get some help from u --If you wish to help
I have this Lenovo A328 which suddenly had multiple and continuous gapps crashes. I tried to do a factory reset but the problem still existed. I decided to flash the stock rom using SP Flash Tool. Flashing the stock rom succeeded but then after, the device does not charge nor boot up. It does not even respond to vol up(or down) + power which brings up a menu for testing the device(not recovery). I tried to format it first before flashing but the result is still the same. I also tried flashing stock rom from different source. Any idea on this one?
Update
I tried to flash a stock rom on my Lenovo A328 with SP Flash Tool but the process was interrupted and now after I flashed the stock rom successfully, the phone won't charge nor boot, not even to recovery. I noticed in my EMMC Flash that the sizes of GP1 - 4 are all 0x0.
I found a solution in here,
http://forum.xda-developers.com/show....php?t=2792667
It says that I have to flash the rom using DOWNLOAD first and then flash it again with FIRMWARE UPGRADE. I'm already at the FIWMWARE UPGRADE process but I got this error
Failed to get PMT info.
Click to expand...
Click to collapse
Can anyone please help me fix the phone? It will be highly appreciated.
Hi,
You can try format all+download option of spflashtool. I can send you the firmware for Lenovo a328 if you want.
Same problem here, any advice ?
You can try format all+download option of spflashtool. I can send you the firmware for Lenovo a328 if you want. Yes i want.
Lenovo a328
Plz send the firmware for Lenovo a328
Hi All,
I have the same problem
did you find any solution?
I want the firmware for Lenovo a328
lenovo a328 not turning on even I successfully flash sa firmware
same problem here.
someone can help?
need some help to resurrect my lenovo a328.
if I format it, there's an error 5073.
Hi, I am having the same problem. Could you help?
Hello everyone!
I am facing the same problem!!!
Tried almost all the solutions suggested on different sites or forums, nothing works, still no charge and no start...
Change the PC, the USB cables, drivers, ROM's, you name it... Someone said this MTK devices are hard to brick but still, why we cannot revive our devices??? Hardware failure? Not really according to some technicians as long your phone is detected by the pc in device manager, the phone CAN be "unbricked".
SO, we are missing something, we doing something wrong???
We need help.... SOMEONE???
please send me the firmware
I have the same problem about my lenovo a328. After flashing, it's not booting and turning on. It's not even charging. So what I did is I tried to firmware upgrade it and I got this ''failed to get PMT info'' alert. Someone know how to revive this phone?
I got 2 phones and they've bricked themselves
Hi,
I got 2 Lenovo A328s and they've bricked themselves, having the same symptoms.
I can get them to boot in Recovery, and I am waiting to download an image to sideload with ADB, which seems to work.
One of them was still in use, but had software glitches, like the camera driver not working in any app.
The other one was replaced 10 months ago, but after long time, it also bricked.
I haven't attempted any flash of new firmware.
I have the same problem, the phone isn't charging and I can't use vol up+ power buttons.
Can you send me the software please and some instructions?
Hi everyone i was trying to upgrade my phone's os which is 6.1 to 7.1. i did it with the help of TWRP which failed and my phone was working in recovery mode and. Later was strucked in boot loop. Later i was trying to flash stock rom. But my phone got bricked. It's off for several days it doesn't respond to pressing power buttons nor does it responds to connecting to charger. But while i connect it to computer the new usb added sound comes from computer.
I'm really strucked guys help me out. Every video i see online is for phone which are strucked in boot loop. I'm sure if I'm able to reach that state I'll make it working but for instance ineed to revive it. My friend says i have deleted bootloader how can i put it back ?. Also we disassembled it and assembled it again. It also didn't work.
Well you did something stupid. Upgrading from MM to Nougat without clean flash? Also flashing stock rom with TWRP? Well you can't revive anymore.. If you really Hard bricked buy new phone
Hitler97 said:
Hi everyone i was trying to upgrade my phone's os which is 6.1 to 7.1. i did it with the help of TWRP which failed and my phone was working in recovery mode and. Later was strucked in boot loop. Later i was trying to flash stock rom. But my phone got bricked. It's off for several days it doesn't respond to pressing power buttons nor does it responds to connecting to charger. But while i connect it to computer the new usb added sound comes from computer.
I'm really strucked guys help me out. Every video i see online is for phone which are strucked in boot loop. I'm sure if I'm able to reach that state I'll make it working but for instance ineed to revive it. My friend says i have deleted bootloader how can i put it back ?. Also we disassembled it and assembled it again. It also didn't work.
Click to expand...
Click to collapse
any luck reviving your phone? isn't there something like Odin for ASUS to reflash stock rom back?
Search youtube for asus zenfone max 8939 you will find twrp and 7.0 custom rom. My phone is zenfone max 2016 and I'm using resurrection remix rom.
My zenfone 6 were stucked in a bootloop, I dont know what happened I didn't root it or anything, One day I rebooted it then stuck on bootloop, I tried ADB but my computer cant read it, What am I gonna do now? please help its almost been a year :crying: