In trouble..... - Galaxy Note 4 Q&A, Help & Troubleshooting

I've flashed roms, recoveries, modems, etc. on many different phones over the years and never had a single problem. Well, I finally got bit.
Just tried to flash TWRP on my new Note 4 SM-N910C. TWRP works but phone is stuck in bootloop. I've searched for almost two hours for answers, tried to flash a different recovery I found, and no luck yet. Should I have rooted the phone first? Can I just flash the stock recovery back on it - if so where would I find it? Can I flash the 5.1.1 firmware from Sammobile on it? (assuming I can actually get it to download from that site! grrr.....) Maybe another dumb question - I see firmware for a ton of different countries for the SM-N910C - I didn't look which one my phone had on it but everything was in English on my phone. Are they all in English?
Any help would be GREATLY appreciated!!

Related

Solution for soft-bricked N9005 after flashing Hong Kong's TGY firmware

I am posting this to help people who ran across the same problem I did the past 24 hours, which drove me crazy and it was quite difficult to find any info on it.
I bought my N9005 on eBay from a Hong Kong seller. I just updated it with Kies and noticed that sammobile.com has a newer MJ8 firmware, so I figured I'd just download it and flash it via Odin.
Kies shows my mobile as XME (Malaysia region), but I guessed it should work just fine, and boy was I wrong.
Moments after trying to flash it, it failed, but it did manage to flash the beginning of the firmware, which was the new MJ bootloader. That newer bootloader does not allow any other firmware with older bootloader be flashed on the phone. Not even Kies's emergency recovery was able to revive my phone which was stuck in emergency download mode.
When trying to flash I got all sorts of errors, such as:
invalid ext4 image
and
CHECK FAIL : fused : 2 , Binary : 1. (when trying to install the older XME Malaysian Firmware on top of the new bootloader)
To make a very long story short, after almost giving up and start waiting for a Malaysian firmware with the new bootloader to be released, I ran across the UK MJ6 BTU rom which does have the new bootloader too and decided to try flashing it. To my amazement - this worked and my phone is back to life! phewwwww!
This is a download link to the BTU MJ6 firmware:
http://www.hotfile.com/dl/252753467/b379b8f/N9005XXUDMJ6_N9005OXADMJ4_BTU.zip.html
Hope this helps others!
P.S. If this information helped you, please click the "THANKS" button below. It's free of charge.
doclucas said:
I am posting this to help people who ran across the same problem I did the past 24 hours, which drove me crazy and it was quite difficult to find any info on it.
I bought my N9005 on eBay from a Hong Kong seller. I just updated it with Kies and noticed that sammobile.com has a newer MJ8 firmware, so I figured I'd just download it and flash it via Odin.
Kies shows my mobile as XME (Malaysia region), but I guessed it should work just fine, and boy was I wrong.
Moments after trying to flash it, it failed, but it did manage to flash the beginning of the firmware, which was the new MJ bootloader. That newer bootloader does not allow any other firmware with older bootloader be flashed on the phone. Not even Kies's emergency recovery was able to revive my phone which was stuck in emergency download mode.
When trying to flash I got all sorts of errors, such as:
invalid ext4 image
and
CHECK FAIL : fused : 2 , Binary : 1. (when trying to install the older XME Malaysian Firmware on top of the new bootloader)
To make a very long story short, after almost giving up and start waiting for a Malaysian firmware with the new bootloader to be released, I ran across the UK MJ6 BTU rom which does have the new bootloader too and decided to try flashing it. To my amazement - this worked and my phone is back to life! phewwwww!
This is a download link to the BTU MJ6 firmware:
http://www.hotfile.com/dl/252753467/b379b8f/N9005XXUDMJ6_N9005OXADMJ4_BTU.zip.html
Hope this helps others!
P.S. If this information helped you, please click the "THANKS" button below. It's free of charge.
Click to expand...
Click to collapse
Thanks buddy for helping me, got me up and running again :good:
You're welcome, mate!
Softbrick
Thank you thank you thank you thank you .
I always liked Hong Kong roms on note one and two and I thought I can continue the tradition .
Softbricked it , and no solution anywhere . I installed this and voila . Back in business . I also installed MJ7 on top now all is good .
Have I said thank you ?
Well thank you !
budalica said:
Thank you thank you thank you thank you .
Have I said thank you ?
Well thank you !
Click to expand...
Click to collapse
You're welcome. Did you press the "Thank you" button?
Thanks a lot. Without your post, my phone will still be bricked.
hh
That day! ! Me too
Useful info, I'm sure this will be of use in many situations.
Thankyou.
Sent from my GT-I9100 using Tapatalk 4
uscool said:
Thanks buddy for helping me, got me up and running again :good:
Click to expand...
Click to collapse
could someone please upload that firmware again on some other hoster? because hostfile isnt working anymore. couldnt find the file on any other server by myself.
lalahamid said:
could someone please upload that firmware again on some other hoster? because hostfile isnt working anymore. couldnt find the file on any other server by myself.
Click to expand...
Click to collapse
Here is the newer version from UK BTU: N9005XXUDMJ7_N9005OXADMJ4_BTU.zip
http://terafile.co/29f621508415
doclucas said:
I am posting this to help people who ran across the same problem I did the past 24 hours, which drove me crazy and it was quite difficult to find any info on it.
I bought my N9005 on eBay from a Hong Kong seller. I just updated it with Kies and noticed that sammobile.com has a newer MJ8 firmware, so I figured I'd just download it and flash it via Odin.
Kies shows my mobile as XME (Malaysia region), but I guessed it should work just fine, and boy was I wrong.
Moments after trying to flash it, it failed, but it did manage to flash the beginning of the firmware, which was the new MJ bootloader. That newer bootloader does not allow any other firmware with older bootloader be flashed on the phone. Not even Kies's emergency recovery was able to revive my phone which was stuck in emergency download mode.
When trying to flash I got all sorts of errors, such as:
invalid ext4 image
and
CHECK FAIL : fused : 2 , Binary : 1. (when trying to install the older XME Malaysian Firmware on top of the new bootloader)
To make a very long story short, after almost giving up and start waiting for a Malaysian firmware with the new bootloader to be released, I ran across the UK MJ6 BTU rom which does have the new bootloader too and decided to try flashing it. To my amazement - this worked and my phone is back to life! phewwwww!
This is a download link to the BTU MJ6 firmware:
http://www.hotfile.com/dl/252753467/b379b8f/N9005XXUDMJ6_N9005OXADMJ4_BTU.zip.html
Hope this helps others!
P.S. If this information helped you, please click the "THANKS" button below. It's free of charge.
Click to expand...
Click to collapse
my brick story in short is------ brought note 3 sm-n9005 from ebay from a Hong Kong based seller. pics of ap, cp and csc are attached. rooted with chainfire's and installed cwm6 by chenglu. A few days back, flashed bobcat rom version 2(mj7) and later 3( mk2 ) without problems. Was looking for different themes .yesterday flashed balckchrome from s4 forum that also went smooth. Unfortunatly flashed another theme for s4 which was not meant for andriod version 4.3. Pretty stupid .went into bootloop. Had nandroid backup tried to restore but couldn't.
Flashed another rom mk2 from cwm. again bootloop .took the odin route and flashed stock deodesk mj7 by Djembey from this thread.
http://forum.xda-developers.com/show....php?t=2461929
Failed again. Then downloaded latest mk2 from sammobile website. The same error (invalid ext4 img) in short failed on all ccounts. Have run out of options. The last thing in mind is to wait for some new bootloader after mk2 which might rescue me as mentioned in this thread that new bootloaders might help... Any guidance will be appreciated. Thanks
@pyarajaani
Try this:
1) Get X-Note v6 custom rom.
2) Use Odin to install CWM recovery.
3) boot the phone into CWM recovery and copy the X-NOTE rom (MK2 based) to your phone or card.
4) Do a complete wipe/factory-reset from CWM
5) Install the X-NOTE rom from CWM
And let me know how it went
doclucas said:
@pyarajaani
Try this:
1) Get X-Note v6 custom rom.
2) Use Odin to install CWM recovery.
3) boot the phone into CWM recovery and copy the X-NOTE rom (MK2 based) to your phone or card.
4) Do a complete wipe/factory-reset from CWM
5) Install the X-NOTE rom from CWM
And let me know how it went
Click to expand...
Click to collapse
Why did you suggest X-Note but not another ROM?
3 reasons:
- It's MK2 based
- I am using it
- It's excellent
And besides, if the method I suggested works, he can always replace a ROM later on if he wishes.
doclucas said:
3 reasons:
- It's MK2 based
- I am using it
- It's excellent
And besides, if the method I suggested works, he can always
replace a ROM later on if he wishes.
Click to expand...
Click to collapse
Thanks for the suggestion. ..tried twice with both stock n Civato kernels.. didn't go beyond Samsung logo screen....With Civato there appears some error above the logo...pics i m attaching. .Thanks again.
doclucas said:
3 reasons:
- It's MK2 based
- I am using it
- It's excellent
And besides, if the method I suggested works, he can always replace a ROM later on if he wishes.
Click to expand...
Click to collapse
Nope, I didnt mean what is the best rom to use.
The problem is that how to bypass the bootloop issue.
pyarajaani said:
Thanks for the suggestion. ..tried twice with both stock n Civato kernels.. didn't go beyond Samsung logo screen....With Civato there appears some error above the logo...pics i m attaching. .Thanks again.
Click to expand...
Click to collapse
No need to mess with kernels.
Were u able to install cwm via odin and then boot into cwm?
doclucas said:
No need to mess with kernels.
Were u able to install cwm via odin and then boot into cwm?
Click to expand...
Click to collapse
yes...I did that n installed X note rom from cwm. BUT I suspect that cwm is not fully functional. Why I m saying this is that I have a nandroid backup of bobcat mj7 rom...which cwm isn't able to detect even. ..nevertheless. .cwm is installed.
1) Which CWM version do you have installed?
2) Did you do a full wipe/factory-reset?
3) Did you try also advanced formatting (of system partition together with the full wipe) and then install the ROM?
4) Did you try all the above with the latest TWRP recovery instead of CWM?
http://forum.xda-developers.com/showthread.php?t=2467255
Try to flash this file by cwm first and then flash any rom after you want
https://www.dropbox.com/s/bibytggk2m8npw8/Brick_Loop_FIX_Fix.zip
Sent from my SM-N9005 using Tapatalk

[Q] Trouble flashing new roms afterLP stock flash. (N910F)

Hi guys,
I really hope someone can point me in the right direction here, I'd really appreciate it!
I've never had to ask for help before with flashing one of my devices, and have flashed hundreds of times with my previous phones, S3, S5 and Note3 .. However this one has me a bit stumped. I have the Note4 N910F and I see many awesome LP ROMS seem to require that you flash stock 5.0.1 via Odin before flashing the custom ROM.
I managed to do this successfully with the ROM listed at Sammobile called "Unknown 5.0.1 N910FXXU1BOC3 N910FTPD1BOC1" - Everything is OK, boots perfectly and I have cell signal and LTE. Rooting was also a non-issue. The problem I have though is that no matter which custom recovery I try, and regardless of ROM that I try, all seem to get stuck in a boot loop at the Samsung screen.
Am I doing or have done something horribly wrong?
Please help!
I think I may have answered my own question. The stock ROM I flashed was BOB3, it seems I need to be on BOB4, which is the German based ROM. Busy downloading that now!
korval said:
I think I may have answered my own question. The stock ROM I flashed was BOB3, it seems I need to be on BOB4, which is the German based ROM. Busy downloading that now!
Click to expand...
Click to collapse
Why can't you flash custom rom's with BOB3 installed?
Thanks

S5 recovery 20$ min read all please. I'm desperate

- Intro
- Done and searched so far
- My Questions. (Jump to the end unless you think I haven't search prior )
- Bounty
INTRO
Hey guys. I'm french Canadian (please understand my bad written )
and thanks to the phone I choosed (s5 active g870w telus)
I'm becoming pretty much bilingual I've checked all over
around The Web and over this forum. And can't find an accurate
answer . I know I picked the wrong phone for rooting but
as a construction worker it was a good compromise.
DONE AND SEARCHED
My Samsung Galaxy s5 Active g870w from Telus
is still on 4.4.2 since there is no and there will not be
any update for a while.
I managed to used the g900w8 version of
Chain fire auto root method using Odin 3.09
to get roots.
I have also succès to flash Unity 2.0.1 rom.
So far I figured that my version can count as
the Canadian version of the s5 small g900w8. (I may be wrong)
I found a stock Firmware (that accualy make my
lies in russian ) Wich I used a lot lately due to all
my soft brick.
My goal is to be able to upgrade to a nice custom rom
on lollipop. I was hoping Fusion. And as for the recovery
TWRP would be my choice if it was possible.
Now I am stuck trying to install TWRP. I have followed
multiple guide. I have tried to install from TWRP manager
the version 2.8.6.0 klte. I have tried 3 times and after the app
installation I tried to reboot to recovery using Quick boot,
i always end up in Odin mode.
I then tried to install using Odin flashing the same version
Downloaded from TWRP.me site. Then it let me load into
my stock version. Then if I try to reboot in recovery
it still stock.
I even tried to use safestrap both version at&t and Verizon
and both soft bricked me.
I have read or scan about every thread and none talk about
S5 a g870w. Beside the att version Wich are locked.
QUESTIONS
My Questions and I really beg for answers even if
You have only 1 answer.
1- Is my phone g870w compatible g900w8?
2-is it compatible to any other versions?
3-when looking should I only look for Canadian version or I can also
use either g870 from at&t,Verizon or international. Or I look for
International g900. Since I guess my bootloader is unlocked .
4- Since only at&t and Verizon are supposed to be lock I guess
I can't use safestrap... so are TWRP and CWM the only options?
5- Can someone help me troubleshoot my installations. ?
6- After I install my recovery a a g870w on kitkat 4.4.2
Should I be able to flash lollipop base custom rom?
7- Is it possible that there is no option for me beside
Unity and stock rom.
BOUNTY
It might not be much but I offer a 20$ minimum bounty for who ever
take me outta this non ending bulls*"t.
Thanks guys. And please I swear I have search and read a lot
just Google my model number and you'll always end up on me
Searching and I seems to be the only one g870w talking about
recovery or custom rom. All I found is how to root...
Jon
1- Is my phone g870w compatible g900w8?
No, it is different flashing anything that isn't designed for your exact model number ( even the AT&T ones which are one letter different) won't work.
2-is it compatible to any other versions?
No, only firmwares for your exact phone will work without someone modifying something specific for you.
3-when looking should I only look for Canadian version or I can also
use either g870 from at&t,Verizon or international. Or I look for
International g900. Since I guess my bootloader is unlocked .
Flashing any other model number but your own risks bootloop/bricking as they although look similar can have different firmware partitions amongst other things.
4- Since only at&t and Verizon are supposed to be lock I guess
I can't use safestrap... so are TWRP and CWM the only options?
If someone can have a look at TWRP is possible that they can make a version work for you: ideally I would say with it being so difficult as so few have your model I would go to stock: root and use xposed, and leave the rest.
5- Can someone help me troubleshoot my installations. ?
Sure, happy to help but don't know how much can help when you are trying firmwares for different versions.
6- After I install my recovery a a g870w on kitkat 4.4.2
Should I be able to flash lollipop base custom rom?
Unless someone has made I've for your model type I doubt it.
7- Is it possible that there is no option for me beside
Unity and stock rom.
Yeah unfortunately this is quite likely.
thanks for taking the time.
Now I'll go private with you for personal things.
but before maybe few extra questions will help the very few others in
the same painful situation.
about compatibility you answered no.
What made me search so bad is that I've seen
other members(g870a) claiming they we're using
g900 roms I'll search for a link.
-Does it mean even tho its risky or
it means that American version have more luck ?
-am I still able to use a recovery like safestrap?
-can I hang myself?
- and if I'd like to have TWRP and a know custom rom
would it be a lot of works for Des.
Is it "askable" are some working for money?
I hate stuck to death I miss my note 3 like crazy. .. damn

N910C update to 5.1.1 failed

Good morning, my friends!
I have a little problem while I tried to update my note 4 910c turkey version via Odin.
I flashed the original 5.1.1 rom. Everything looked ok, but when the phone rebooted nothing happened. That's not at my first smartphone with android so I really have a pretty ideea how to flash something via Odin.
Also I tried a few weeks ago to flash another original ROM and the same thing happened.
Can you give me some ideas about that?
Thanks a lot for your attention!
Cheers!
adinel.berehorschi said:
Good morning, my friends!
I have a little problem while I tried to update my note 4 910c turkey version via Odin.
I flashed the original 5.1.1 rom. Everything looked ok, but when the phone rebooted nothing happened. That's not at my first smartphone with android so I really have a pretty ideea how to flash something via Odin.
Also I tried a few weeks ago to flash another original ROM and the same thing happened.
Can you give me some ideas about that?
Thanks a lot for your attention!
Cheers!
Click to expand...
Click to collapse
May be to wipe first data,system,cache on 5.0.1 stock and then flash 5.1.1?
Try to download again ROM from samm,or from mega(u have links here on xda)
adinel.berehorschi said:
Good morning, my friends!
I have a little problem while I tried to update my note 4 910c turkey version via Odin.
I flashed the original 5.1.1 rom. Everything looked ok, but when the phone rebooted nothing happened. That's not at my first smartphone with android so I really have a pretty ideea how to flash something via Odin.
Also I tried a few weeks ago to flash another original ROM and the same thing happened.
Can you give me some ideas about that?
Thanks a lot for your attention!
Cheers!
Click to expand...
Click to collapse
Did you follow the instruction givin in the sammobile website?
Did you unzip the file?
check AP then add on it
if so maybe you should re download the rom.
i did the update over the 5.0.1 no issues .... then i decided to wipe and flash clean and that was super good
what do you mean by nothing happened? it still 5.0.1 firmware ??

N900 Not Rebooting System After Flash

Hi all,
I've recently been gifted the note 3 n900 and rooted it. I also installed TWRP and CWM as well, and when i go to install a ROM, it does say successfully and then at reboot, it shows the samsung galaxy note 3 screen, after that it goes blank. I've to do a battery pull to get it back and then restore a backup. I've tried many ROMs and also did rooting again, still nothing.
I've been using the galaxy s4 i9500 for about 2 years now and that is rooted and i've been flashing roms on it all year long with no problem. I'm just not sure what's going with this.
I'm currently on 4.4.2 official stock as I can't do much. Lollipop has not yet come to my region i think.
Any help would be widely appreciated.
Thank you in advance.
Same Issue here but I am even not getting a samsung logo or a custom rom logo.
bilicool said:
Hi all,
I've recently been gifted the note 3 n900 and rooted it. I also installed TWRP and CWM as well, and when i go to install a ROM, it does say successfully and then at reboot, it shows the samsung galaxy note 3 screen, after that it goes blank. I've to do a battery pull to get it back and then restore a backup. I've tried many ROMs and also did rooting again, still nothing.
I've been using the galaxy s4 i9500 for about 2 years now and that is rooted and i've been flashing roms on it all year long with no problem. I'm just not sure what's going with this.
I'm currently on 4.4.2 official stock as I can't do much. Lollipop has not yet come to my region i think.
Any help would be widely appreciated.
Thank you in advance.
Click to expand...
Click to collapse
Hi
I had this problem for a couple of days, I found out that I flashed a incompatible rom via Odin. Can you can go into fast boot mode and tell me what it says at the top? Mine said " Couldn't do normal boot " which means the rom I flashed was not supported for my device. I went to the Samsung website to download a rom that was compatible with my device, I flashed it via Odin and it worked.
Thanks
I Just got my error fixed. U need to flash your bootloader via odin
Faizan Farrukh said:
I Just got my error fixed. U need to flash your bootloader via odin
Click to expand...
Click to collapse
Yup thanks buddy. Fixed.
Faizan Farrukh said:
Same Issue here but I am even not getting a samsung logo or a custom rom logo.
Click to expand...
Click to collapse
AADAMHITMAN said:
Hi
I had this problem for a couple of days, I found out that I flashed a incompatible rom via Odin. Can you can go into fast boot mode and tell me what it says at the top? Mine said " Couldn't do normal boot " which means the rom I flashed was not supported for my device. I went to the Samsung website to download a rom that was compatible with my device, I flashed it via Odin and it worked.
Thanks
Click to expand...
Click to collapse
I found that flashing the Stock Lollipop Rom worked, just as mentioned above by the above post. Yes, just by updating the bootloader i think it works. I've done it by getting the Russian stock rom from sammobile (even though i'm not in Russia), works like a charm. Really love the new feel to the note 3 n900. Just need to find a way to get permissive kernel now and ites perfect.

Categories

Resources