Related
Hi,
since a week or so my u8800 suffers from a huge battery drain.
Today i just got 10hours out of it and almost did nothing. (4min. phone call/ 10messages/ max. 10min surfing)
The last 10% of battery was gone in 30 seconds.
It all started last week when my phone was on stock 2.2. Then i updated to the latest stock 2.3.5, but still the same problem.
Model number : u8800
Android version : 2.3.5
base band version : 404020
Kernel version : 2.6.35.7-perf [email protected]#1
Build number : U8800V100R001C00B528G001
I also wanted to calibrate the battery, but i can't root the phone. Tried every program out there
Anyone got the same problem or has a solution ?
Hello Kawadude,
I use superoneklick and it works fine to root the device. Hier ist the how to, what you must do before use superonklick:
- Dial * # * # 2846579 # * # *
- Go to projectmenu, background settings, log settings, log switch and set Log on
- Reboot phone
- Set USB debugging on
- Run superonklick http://depositfiles.com/files/n0dcxce3t or http://shortfuse.org/
Hope it helps
Already tried that without a result.
I also tried DooMLoRD v4, Unlock Root and One-click Root.
Since i installed the official 2.3.5 i can't root my device annymore. On stock 2.2 this wasn't a problem.
Hello, do you keep wi fi enabled at all times? i noticed my battery drains increased greatly when i leave my wifi on 24/7
No, wifi is only enabled when I'm at home.
A couple of weeks ago the battery life was just fine. (With the same usage)
Kawadude said:
No, wifi is only enabled when I'm at home.
A couple of weeks ago the battery life was just fine. (With the same usage)
Click to expand...
Click to collapse
Close any application in your pc that might try to connect with an android device (like huawei's or Asus PC Sync, etc). Those applications use the adb driver and block superoneclick. Check if windows recognize your device and install it properly. Hum... That's all I can think of... ;-)
Igory0k said:
1.Settings-> Applications -> Developer Tools-on
2.Unknown sources -> Settings-> Applications -> Unknown sources-on.
3.Fast boot -> Settings-> Applications-off
4.Dial: *#*#2846579#*#*
5. Go to projectmenu > background settings > log settings > log switch > set Log on
6.log setting-dump & log-on
7.Reboot Phone
Download B528_ROOT
8. Run B528_root.bat
9. Your phone should now be Rooted.
10. You can now go back *#*#2846579#*#* and turn logging off if you want.
Click to expand...
Click to collapse
Try this. I did hear that this last release from huawei (B528) couldn't be/was really hard to get rooted. I haven't tried this, just found it. Credit to @Igory0k.
MtG92 said:
Try this. I did hear that this last release from huawei (B528) couldn't be/was really hard to get rooted. I haven't tried this, just found it. Credit to @Igory0k.
Click to expand...
Click to collapse
Didn't work for me.
The phone rebooted and freezed at the huawei logo.
The only thing i didn't find is step 6: "6.log setting-dump & log-on"
Kawadude said:
Didn't work for me.
The phone rebooted and freezed at the huawei logo.
The only thing i didn't find is step 6: "6.log setting-dump & log-on"
Click to expand...
Click to collapse
You have to do it, rooting apps need that option
And launcher apps etc. don't install them, your battery won't drain Uninstall unnecessary apps too
Moved To Q&A
Please post all questions in the Q&A section
I can't open the quick settings menu from the notification center and can't really do much. Only interact with already installed apps. I can't hange the user, I can't enable developer options I can't save the files via USB and neither does adb work.
I never worked with a Motorola, do you have any idea what I could try?
___
Android 6.0.1 // Build MPDS24.107-52-5
System version 24.201.5.lux_reteu.reteu.en.EU.reteu
(not rooted)
Polyparadox said:
I can't open the quick settings menu from the notification center and can't really do much. Only interact with already installed apps. I can't hange the user, I can't enable developer options I can't save the files via USB and neither does adb work.
I never worked with a Motorola, do you have any idea what I could try?
___
Android 6.0.1 // Build MPDS24.107-52-5
System version 24.201.5.lux_reteu.reteu.en.EU.reteu
(not rooted)
Click to expand...
Click to collapse
If it happened all of a sudden after OTA update, check out this answer:
https://forum.xda-developers.com/showpost.php?p=70320663&postcount=2
Has anyone installed the Nougat update for the Asus Zenpad 10 Z300M?
Yes I do, what do you need to know?
I didn't know there was an update to Android 7 - I'm still hoping (probably in vain) for this tablet to be rooted.
fabfor said:
Yes I do, what do you need to know?
Click to expand...
Click to collapse
I was just wondering if there were any noticeable changes or any issues with it as of yet.
Thanks for the reply.
Is the update OTA or from a website?
odyseus said:
Is the update OTA or from a website?
Click to expand...
Click to collapse
OTA
---------- Post added at 14:19 ---------- Previous post was at 14:13 ----------
PeteSeiler2010 said:
I was just wondering if there were any noticeable changes or any issues with it as of yet.
Thanks for the reply.
Click to expand...
Click to collapse
Changes are those in the changelog. I haven't noticed any issues so far but multi user support isnt't there and I was hoping yes.
ASUS ZenPad 10 Android Nougat Changelog:
Update Google security patch
Remove redundant app shortcuts “Audio Wizard” “Splendid” “System update” and “Flashlight” from all apps menu
Remove ”PC Suite” (CD ROM)
Remove “Tap and hold to show menu” form Settings > ASUS customized settings > Touch key setting. Add “Tap and hold to activate Multi-window ” in Touch key setting
Quick Settings supports multiple pages , user can swipe left to right to see more quick settings if using more than 12. User can enter edit screen by tap the edit button on top right corner to determine which settings enabling or disabling
Default Tap and hold Recent apps key to activate Multi-window
Add “Game Genie”
ZenUI Keyboard added New Unicode code 9.0 emoji and skin tone.
The preloaded Holo Spiral, Bubbles, Black Hole, and Phase Beam live wallpapers are not compatible with Android N and will be removed after system update
Add bundled notifications switch. (Settings > Notification > Configure notifications.) When multiple notifications for a single app are received, they can be bundled together into a single group. This group can be expanded to see the individual messages
Add Lock screen wallpaper slideshow
Change wallpaper every time you wake up your device. And users can go to “Settings” -> “Lock screen” -> “Wallpaper slideshow settings” for setting
Update SMMI tool to SMMI_TEST_V5.1.74_CSC_L1L2
Support Unlock tool
Click to expand...
Click to collapse
Must be US update then as still running Android 6.x here in the UK
Odd .. haven't gotten it .. and I check every couple of days ..
It could be me, but it seems like my battery dies faster after having the update for a few days.
odyseus said:
Must be US update then as still running Android 6.x here in the UK
Click to expand...
Click to collapse
No, it's worldwide.
The official website have the link of the update, and you can apply it manually.
http://dlcdnet.asus.com/pub/ASUS/Ee...62.438207375.1494693050-1331990512.1494693046
Hello, pls can anybody help? I bough z300m from second hand, turn on it (not try log in to google) and on startup screen (language select) system ask me for update to nougat, i click OK, system updated, tablet restarted and i cant log into tablet (FRP).
I search for bypass z300m on nougat, but cant find it.
This procedure dont work for me (android 7.0)
So i need flash from fastboot, but i cant find flashtool for z300m (p00c), firmware i downloaded from official page.
Any solutions?
Thanks.
Edit. I cant turn on usb debugging in developer settings (system want log in for view all options in developer settings...)
Nougat
PeteSeiler2010 said:
Has anyone installed the Nougat update for the Asus Zenpad 10 Z300M?
Click to expand...
Click to collapse
I did the nougat OTA update yesterday,it took a few minutes to download,but it is working great !
macikcz said:
Hello, pls can anybody help? I bough z300m from second hand, turn on it (not try log in to google) and on startup screen (language select) system ask me for update to nougat, i click OK, system updated, tablet restarted and i cant log into tablet (FRP).
I search for bypass z300m on nougat, but cant find it.
This procedure dont work for me (android 7.0)
So i need flash from fastboot, but i cant find flashtool for z300m (p00c), firmware i downloaded from official page.
Any solutions?
Thanks.
Edit. I cant turn on usb debugging in developer settings (system want log in for view all options in developer settings...)
Click to expand...
Click to collapse
Bad news I'm afraid. You need the original login details used to setup the device when it was originally purchased other than that it's a long winded battle with ASUS to prove you didn't steal the device.
Good luck
After update the system reboots all the time when WiFi is ON.
If I turn OFF wifi - it works fine. No other solution...
root / multi-user
fabfor said:
OTA
---------- Post added at 14:19 ---------- Previous post was at 14:13 ----------
Changes are those in the changelog. I haven't noticed any issues so far but multi user support isnt't there and I was hoping yes.
Click to expand...
Click to collapse
There is a thread right after this listing when search for Z300M on XDA that claims TWRP and asus bootloader unlock tool (not necessary 2 get twrp) and was the reason I purchased this tablet. So far errors in everything in the OP with no responses and I hate to be paranoid but once I know, if not twice I have actuall run into "FAKE" threads on XDA in the 2-3 years being on here claiming root/twrp for a device with a small amount of chit chat, responses.... that was pure BS!
Anyhow, if you ever get root here is the fix for your multi-user issue, with es file explorer, or root explorer and editing the boot. file:
Enable Multi Window and Multi User Modes
If you have a rooted Marshmallow ROM (or Nougat), you can enable the 2 features above by editing the build.prop file found in /system/
For multi-window mode, change this entry in build.prop
ro.build.type=user
to -
ro.build.type=userdebug
To enable multi-user mode, add these 2 lines to the build.prop (anywhere, it doesn't matter)
fw.max_users=3
fw.show_multiuserui=1
Once you've made these changes, reboot the tablet.
To use multi-window mode, go to Settings, Developer options, and there will be a new menu item to switch this on or off.
To use multi-user, there will be a new option under Settings called Users.
If anyone seeing this has accomplished root on the Z300M 16GB wi-fi tablet, please let me know.....
thanks,
zach
ps of course, make sure you make a copy of the boot file to ext sd card or somewhere b4 just in case.... in the 15 times I have used this on 6.0, 7.0 lenovo & LG devices & 1 HTC... never had an issue BUT...
---------- Post added at 05:26 PM ---------- Previous post was at 05:19 PM ----------
odyseus said:
Must be US update then as still running Android 6.x here in the UK
Click to expand...
Click to collapse
Actually all of the updates for the Z300M taking it to 7.0 are for the WW SKU (world wide) tablets, as well one for Japan and 1 other.........
any sign of root?
Asking around since purchasing this tablet due to thread on here claiming twrp but its falling on its face and no response as of yet.....
zach
?????
coolbeans2016 said:
Anyhow, if you ever get root here is the fix for your multi-user issue, with es file explorer, or root explorer and editing the boot. file:
Click to expand...
Click to collapse
Thank you coolbeans2016, that's right the reason I am too desperately looking for a way to root: to apply that fix.
Btw, I really do not see the reason for Asus to disable a native function (multi-user) that is - to me - obvious for a tablet. (Maybe it eats resources? i.e. storage space)
problem is
fabfor said:
Thank you coolbeans2016, that's right the reason I am too desperately looking for a way to root: to apply that fix.
Btw, I really do not see the reason for Asus to disable a native function (multi-user) that is - to me - obvious for a tablet. (Maybe it eats resources? i.e. storage space)
Click to expand...
Click to collapse
Problem is the instructions for getting TWRP flashed or even just booted up on TWRP threaded for installation of SuperSU or Magisk is failing. I've been told I'm wrong and am just not reading or following the instructions correctly but on a VERY popular device there is NO ONE claiming $$PROFIT$$ on the thread! Even the ones claiming understanding of the thread are having complications but only have an average of 6 posts as jr users with no thanks feedback.... yet they have no questions regarding using the SP Flash Tool?!!!!! Strange to me!
I'm contacting the dev on the thread AGAIN to see if I can get a detailed set of instructions in JUST getting TWRP onto this tablet, or its useless to me......
He really thought I was calling his thread a false listing but straightened it out with him about the fact he references another such thread along the same lines for the Verizon Asus A380M, which EVERYONE knows has never been, probably never will be able to get a custome recovery, let alone root of any kind!!!!!!!!
Any info you come across, or if you have tried the thread I'm mentioning please let me know your errors encountered, any ideas how WE may be not taking the instructions correctly.
zach
Hi,
I couldn'tt find any update for Z300CL.
Does anyone know if such an update is available?
Could you post the link here?
Thanks a lot
I used usb ethernet dongle on android 6 and it worked , it showed ethernet icon instead wifi. But when on android 7 the dongle does not work, seems usb host function is disabled, I dont want to root my tabled is there any way to enable usb host support ?
The NFC function lost after upgrating to Stock Oreo 8.1.0, while it works well on 7.1 all the time.
I confirm that I turned on the NFC botton in the settings menue, but the NFC didn't work.
I have unlocked the critical partitions before flashing, also tried OTA, but the NFC doesn't work at ANY TIME.
Anyone can help me? Thanks so much...
It works fine on 8.1 for me but I never unlocked anything. Normally the best thing to do would be to factory reset your phone and choose the start fresh option in the setup menu instead of restoring from a Google backup. Problems after a big update like Nougat to Oreo aren't uncommon and are nearly always fixable by doing a factory reset correctly (fresh start). But since you modded your phone something else might be going on.
symtb said:
The NFC function lost after upgrating to Stock Oreo 8.1.0, while it works well on 7.1 all the time.
I confirm that I turned on the NFC botton in the settings menue, but the NFC didn't work.
I have unlocked the critical partitions before flashing, also tried OTA, but the NFC doesn't work at ANY TIME.
Anyone can help me? Thanks so much...
Click to expand...
Click to collapse
Works fine for me.
I am rooted 8.1, Magisk, ElementalX.
I don't have any issues with it and I'm stock 8.1 unrooted.
I have tried third party Oreo 8.1, the NFC works fine.
Only failed on Stock Oreo 8.1.
I tried another time to do a new flashing with Back_to_Stock package 8.1, when flashing system_a.img and system_b.img, it showed a message " Invalid sparse file format at header magic", and after that, it began to flash the system image normally. But as usual, the NFC didn't work.
-----------
Anything related to the mistake? Thanks.
Deleted
i've got the same issue. nfc doesn't recognize any card or device whilst it is activated in settings and nfc test app says anything is fine.
i'm using android pie but it was the same on oreo. my bootloader is fully unlocked. i always update via back-to-stock and fastboot.
M!tch said:
i've got the same issue. nfc doesn't recognize any card or device whilst it is activated in settings and nfc test app says anything is fine.
i'm using android pie but it was the same on oreo. my bootloader is fully unlocked. i always update via back-to-stock and fastboot.
Click to expand...
Click to collapse
I am running stock 8.1 and NFC didn't seem to work for me either until I touched a tag to the lower portion of the back and it fired. I was used to the sensor in previous phones being in the middle or toward the top. It would not work until it was in the lower 20% of the back side.
Don't know if it will be the same for you, but here's hoping.
yes, it was the same for me. i realized it just a few minutes after my post but didn't find it then. so i couldn't delete it.
I've been fighting to get mine to work, so far nothing. I contacted Essential tech support and they had me clear the cache and showed where the NFC sensor is (bottom part of the phone on the back). I tried using Android Beam to send/receive URL's with my old phone (confirmed that it can send/receive through Android Beam). Nothing is working. Debating whether or not to return the phone and get something else. Any help would be appreciated.
Here's what tech support sent me:
As a verification step, confirm that you're using the correct area of the phone for NFC. Unlike most smartphones, the Essential Phone's NFC chip is located on the bottom of the device.
If you are aware of the NFC position, to isolate the issue further and determine the best way to resolve this, I'd like you to try a few steps.
Ensure that NFC is enabled in settings. (Settings > Connected Devices > Connected Preferences > NFC)
Ensure that Google Pay is the default Tap & pay sevice (Settings > Apps & notifications > Advanced > Default apps > Tap & pay > Payment default > select the desired payment app)
Clear the cache in the NFC Service and reboot the device. (Settings > Apps & Notifications > See all apps > Three dots in the top right > Show System > NFC Service > Storage > Clear Cache)
Attempt to use the NFC service with another app or service like Android Beam (Settings > Connected Devices > Android Beam)
Chiming into this thread - NFC doesn't even show up for me in Connected Devices, on Android 9.
Look under connection preferences in connected devices
kboya said:
Look under connection preferences in connected devices
Click to expand...
Click to collapse
I don't have NFC or android beam in my preferences window.
Ok, what do you have?
Edit: just noticed it's you in two threads
Finally got mine resolved. Received a new phone under warranty yesterday. Confirmed that NFC works.
[GUIDE/TUTORIAL/HOWTO] LG G3 D855 Stock to Android 11
[GUIDE/TUTORIAL/HOWTO] LG G3 LG-D855 (Unlocked/Europe) Stock to Android 11 R/LineageOS 18.1 with all files included, Netflix and Disney+ working
This detailed step-by-step guide helps you transform your LG G3 D855 to a powerful one with Android 11.
I wrote it because what I read was incomplete or outdated.
Make sure your phone is compatible LG G3. In Android, go to Settings > General > About phone > Hardware info > Model number is LG-D855.
If not, quit this tutorial.
### I'll make a few comments like this, PLEASE READ THEM !
### WARNING. DO NOT CHECK FOR ANDROID UPDATES (we'll see this later).
CHANGELOG
v3. Use Netflix and Disney+ in SD
v2. Fix the link to download Android 5 firmware
v1. Initial release for Android 11
1) DOWNLOAD
- djibe LG G3 d855 pack: https://bit.ly/djibe-lgg3-d855-pack
(contains LG USB drivers + LGUP + KingoRoot4.8.apk + b007.autorecd855_2015-04-16.apk + Quick Reboot ROOT.apk + TWRP Recovery 3.5.2_9-0-d855 + Magisk root).
Unzip files.
- ROM LineageOS 18.1 Official: https://forum.xda-developers.com/t/...s990-vs985-lineageos-18-1-31-03-2021.4205475/
Download latest build here: https://server.zacherts.de/smartphone/LG-G3/?C=N;O=D or here: https://www.androidfilehost.com/?fid=4279422670115723669
- BiTGApps Package ARM 11: https://github.com/BiTGApps/BiTGApps-Release/releases
+ Charge phone to 100%
+ Always use USB2 port
No command line will be used ! No need to be a geek.
2) INSTALL USB DRIVERS
Install LG USB drivers (you unzipped earlier).
Then plug phone to PC in File transfer mode (Media device MTP option).
Collect all .jpg or .mp4
Use an app like Backupyourmobile to backup texts, contacts, etc.
Make sure Google account is synced, WhatsApp backups etc...
Check that backup is located on microSD card.
Then copy the backup on your PC.
Go to Settings > General > About phone > Status > IMEI.
Note and save EMEI (15 digits, just in case) !
3) ANDROID VERSION
Go to Settings > General > About phone > Software info > Android version.
- Android version is 6.0: bad news, we have to downgrade it.
Latest MarshMallow (Android 6) updates have closed the root opportunities.
- Android version is 5.0: cool, see you at chapter 5.
4) DOWNGRADE LG G3 TO ANDROID 5 LOLLIPOP
### Many thanks to shakeyabooti: https://forum.xda-developers.com/t/...mp-tot-method-with-lgup.2785089/post-64624353
### D-855 only. If not, read more on https://forum.xda-developers.com/t/...p-tot-method-with-lgup.2785089/#post-64624353
This chapter is only if Android 6 is installed on your LG G3 D-855.
You may try to root with KingoRoot first, because early MM firmwares seem to have vulnerabilities.
Read next chapter to try KingoRoot. If it fails, follow this whole chapter.
Download firmware: http://storagecow.eu/Xda/LG G3/Stock/D855/United Kingdom/UK Europe General D85520I.kdz
### Write to me the day the link dies.
Install LGUP_LG_G3/LGUP_Install_Ver_1_14_3.msi
Then install LGUP_LG_G3/LGUP_8974_DLL_Ver_0_5_CODEFIRE.msi
Shutdown phone.
Plug in USB cable into computer.
Press and hold Volume+ button and plug phone to microUSB.
Hold until Firmware update screen is displayed and release Volume+ button.
Right click on Windows Start Menu icon > Device Manager.
Locate the COM & LPT Ports option and expand it.
Double click on LGE Mobile USB Serial Port.
### No LGE Mobile USB Serial Port ? Install LG USB drivers and restart PC
Double click on LGE Mobile USB Serial Port > Port Settings > Advanced.
Change COM Port Number to COM41.
Confirm with OK and OK Again.
Go to LGUP's Install folder (C:\Program Files (x86)\LG Electronics\LGUP)
Right click on LGUP.exe > Run as administrator
LGUP will load and find phone on Port COM41.
Select UPGRADE and in File Path select the firmware: UK Europe General D85520I.kdz
Now select REFURBISH option.
Make sure BIN File is checked.
Then click on Start.
Wait during firmware flash.
Phone will reboot to Android 5.
Configure Android but DO NOT Agree to "Software Update".
5) ROOT LG G3 IN 2021 (Android 5 LOLLIPOP ONLY)
We need Root to flash a custom recovery.
Disconnect phone from PC..
Turn Wi-Fi off.
Connect phone to PC.
Access its Internal storage using Windows Explorer.
### If storage is not accessible, make sure in Android's notification panel that Media device (MTP) is the active transfer mode.
Copy KingoRoot4.8.apk, b007.autorecd855_2015-04-16.apk, Quick Reboot ROOT.apk AND twrp-3.5.2_9-0-d855.img on it.
On phone, use File Manager app and navigate to All files > Internal storage
Tap on KingoRoot4.8.apk > tap on Security button > Check Unknown sources in Security menu and confirm with OK.
Then complete Stump install by tapping on INSTALL button > Then Open.
Once in KingoRoot4.8 app, tap on Root.
Wait during process.
Authorize any extra installation.
Then KingoRoot ends up with ROOT SUCCEEDED.
6) FLASH TWRP RECOVERY 2.8
Again, use File Manager app and navigate to All files > Internal storage.
Install b007.autorecd855_2015-04-16.apk > Install > Open
Allow root permission.
Wait during backup until Dialog says Everything seems fine...
Tap on Flash TWRP and wait during flash.
Again, use File Manager app and navigate to All files > Internal storage.
Install Quick Reboot ROOT.apk > Install > Open
Allow root permission.
Tap on Reboot Recovery > Confirm Reboot recovery.
Phone reboots to TWRP recovery 2.8.6.0.
7) UPDATE TWRP RECOVERY TO 3.5
Once in TWRP, go to Install > Images... (bottom right button).
Scroll down to twrp-3.5.2_9-0-d855.img > Select Recovery and Swipe to Confirm Flash.
Go back to Home menu > Reboot > Recovery.
8) BACKUP PARTITIONS
In case of a crash, we backup everything.
At TWRP (now 3.5) reboot,
Check Never show this screen during boot again and Swipe to Allow Modifications.
Go to Backup > select Boot, Data, Modem, System and EFS partitions.
Swipe to Backup and wait during backup.
Connect phone to PC.
Back to home screen > Mount.
You can access folders from PC if Data partition is checked and bottom right button displays Disable MTP.
From Windows Explorer, navigate to G3 > Internal Storage.
Copy TWRP folder and paste it somewhere safe on PC.
This is a perfect backup in case of crash.
9) WIPE PARTITIONS
Disconnect phone from PC.
Now go Wipe > Advanced Wipe.
Select Dalvik / ART Cache, Cache, Data, Internal Storage, System and Swipe to Wipe.
Go to Wipe > Format Data.
Type: yes and confirm with bottom right icon.
Tap on Home button > Reboot > Recovery > Swipe to Reboot.
10) FLASH ANDROID, GAPPS AND MAGISK ROOT
On restart, check Never show this screen during boot again and Swipe to Allow Modifications.
Connect phone to PC.
Back to Mount.
Copy ROM + GAPPS + Magisk.
Disconnect phone.
Select lineage-*.zip, and Add More Zips,
then bitgapps*.zip and Swipe to confirm Flash
Be patient.
### If it fails, install zips 1 by 1.
### Updater process ended with ERROR: 1
Then back to Home > Reboot > Recovery.
Install > Magisk*.zip
When done message prompts, tap on Wipe Cache/Dalvik and Swipe to Wipe, wait.
Disconnect phone from PC.
Then tap on Reboot System.
Let the phone boot (about 10 minutes).
11) ANDROID
Configure Android as you like.
- Don't try to use built-in Terminal app, it will reboot phone
- Go to Settings > About.
At bottom, tap 7 times on Build number. You activated Developer options.
Go to Settings > System > Avdanced > Developer options.
Set Windows animation scale, Transition animation scale and Animator duration scale to 0.5x.
- Double Tap to Wake (D2W)
Go to Settings > Display > Advanced and activate it.
12) NETFLIX AND DISNEY+
Open Magisk app (v23+).
Go to Settings > go to App Rename app to Godmode to hide hide.
Below, switch MagiskHide ON.
Now go to Magisk Modules tab > install liboemcrypto disabler and MagiskHide Props Config.
Connect to your Google account, download from Play Store Netflix and Disney+.
Love @HardStyl3r,
Enjoy,
djibe
---------------------------------------------------------------------------------------------------------------------------------
### LG G3 quit firware update
If no flash is happening, just remove battery to quit firmware update.
Thanks: @HardStyl3r (is awesome), @dadi11, @walter79, @aleasto, LineageOS team, BitGApps team, TWRP team, topjohnwu
Great job!
HardStyl3r said:
Great job!
Click to expand...
Click to collapse
Thanks !
Took me many days, but you are AWESOME !!!
Thanks a lot! Doing right now on an old 32gb G3... ;-)
DS-1 said:
Thanks a lot! Doing right now on an old 32gb G3... ;-)
Click to expand...
Click to collapse
Yes this phone is still awesome.
Updated for Netflix and Disney+
Sorry I just realized I copied recently my Nexus 7 2013 tutorial of LG G3.
Fixed now
BiTGappsARM 11 R19 download link does not work, do newer version work? I found this website https://bitgapps.github.io/ is this the correct website?
Immow said:
BiTGappsARM 11 R19 download link does not work, do newer version work? I found this website https://bitgapps.github.io/ is this the correct website?
Click to expand...
Click to collapse
Hi, grab it here: https://github.com/BiTGApps/BiTGApp...nload/v1.7/BiTGApps-arm-11.0.0-R44_signed.zip
This is aweseome!
Thank you so much!
jason88fr said:
This is aweseome!
Thank you so much!
Click to expand...
Click to collapse
Hi jason, glad you liked it !
Enjoy your new phone
Thanks works perfect! Just the mic that wont work on whatsapp, but its ok.
I have a LG-G3 D855 Europe version with 16GB internal storage and 2GB RAM
I read that the main camera doesn't work on the D855 (European version), is that correct?
What else doesn't work when Android 11 is on it?
I have a LG-G3 D855 Euro version with 16GB of internal storage and 2GB of RAM.
At the moment I have Fulmix ROM 6.9 installed (is Android Marshmallow 6) and thus also rooted.
So I could then install the new TWRP 3.5 and then the ROM Lineage OS 18.1 afterwards, proceed as described or do I have to pay attention to something else?
Thanks for the hints and tips
Installed... no WLAN on my LG G3 D855 with Lineage 18.1
Ok, now I've set everything up successfully, on my almost 7-year-old LG-G3-D855 with only 32 GB of memory and still a poor 32-bit device.
The WLAN settings required that I had to switch the WLAN encryption to WPA2 CWP on the AVM Fritzbox 6660 Cabe.
It's sad that such an Android 11 as Lineage 18.1 doesn't get along with normal settings in the Fritzbox as WPA2/WPA3. Didn't the developers pay attention again? something like that is allowed with Android 11 !!! not happen.
Even my old Fulmics 6.9 ROM could work perfectly with the Fritzbox 6660 Frotz OS 7.29 in 2.4 and 5 GHz mode, only Lineage 18.1 can't do anything with it. Already very sad.
But ok, I solved the problem and now the front and rear cameras work as well. I still have to look for an icon pack for the surface, the normal icons look terrible!
Glad you did it.
I don't remember having troubles with Camera.
I can't help about this AVM Fritzbox 6660 Cabe thing. I don't know this.
Hello friend, I have installed this ROM, but testing it, I verify that it does not record video. I have tried other apps such as Open Camera or even the LG Camera apk and the same problem still does not record video. At first I even did a factory reset to see but it still can't record video, do you know any solution or is it because it's the latest version of official Lineage OS that I flashed, what version does the video camera work with? Thank you.
Pinarek said:
I have a LG-G3 D855 Europe version with 16GB internal storage and 2GB RAM
I read that the main camera doesn't work on the D855 (European version), is that correct?
What else doesn't work when Android 11 is on it?
I have a LG-G3 D855 Euro version with 16GB of internal storage and 2GB of RAM.
At the moment I have Fulmix ROM 6.9 installed (is Android Marshmallow 6) and thus also rooted.
So I could then install the new TWRP 3.5 and then the ROM Lineage OS 18.1 afterwards, proceed as described or do I have to pay attention to something else?
Thanks for the hints and tips
Click to expand...
Click to collapse
I had Fulmix 8 and proceed this tutorial and it went well. I wanted Lineage because with Android 6 there are many apps that no longer run. The problem with Lineage OS is that the video camera does not record.
Xlp22 said:
Hello friend, I have installed this ROM, but testing it, I verify that it does not record video. I have tried other apps such as Open Camera or even the LG Camera apk and the same problem still does not record video. At first I even did a factory reset to see but it still can't record video, do you know any solution or is it because it's the latest version of official Lineage OS that I flashed, what version does the video camera work with? Thank you.
Click to expand...
Click to collapse
I fixed it by updating Google Play Services, Play Store and Framework and rebooting.
Xlp22 said:
I fixed it by updating Google Play Services, Play Store and Framework and rebooting.
Click to expand...
Click to collapse
Thx for sharing.
The ROM is Official and nothing appears in the Issues backlog: https://github.com/itsHardStyl3r/LG-G3-issue-tracker/issues
Well done,
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}