My i9505 was running stock KitKat from Samsung and I tried to install CM13 ROM.
So I used Odin to root the phone and installed TWRP 2.8.6.0. After that I flashed the CM13 ROM and the Gapps Nano.
I got as far as rebooting into CM13. But then the "Google Play Store has stopped working" message keeps popping up starting from the initial setup phase. I ignored the message and went on to setup the wifi but couldn't progress any further. The wifi was detected and connected but then it was stuck on the Checking Connection/Software Update step.
I tried to reflash the rom and gapps again to no avail. The third time to Format Data from TWRP before reflashing - still didn't make a difference.
What's worst is now I cannot even get into TWRP! Whenever I press Vol Up + Power + Home, it will show the small 'entering recovery' message momentarily on the top left corner but then it phone simply restarted again.
I tried re-flashing TWRP using Odin, but still didn't work.
I'm stuck now, cannot get into the OS nor the recovery. Any suggestion as to what to do?
Thank you.
vizavalk said:
My i9505 was running stock KitKat from Samsung and I tried to install CM13 ROM.
So I used Odin to root the phone and installed TWRP 2.8.6.0. After that I flashed the CM13 ROM and the Gapps Nano.
I got as far as rebooting into CM13. But then the "Google Play Store has stopped working" message keeps popping up starting from the initial setup phase. I ignored the message and went on to setup the wifi but couldn't progress any further. The wifi was detected and connected but then it was stuck on the Checking Connection/Software Update step.
I tried to reflash the rom and gapps again to no avail. The third time to Format Data from TWRP before reflashing - still didn't make a difference.
What's worst is now I cannot even get into TWRP! Whenever I press Vol Up + Power + Home, it will show the small 'entering recovery' message momentarily on the top left corner but then it phone simply restarted again.
I tried re-flashing TWRP using Odin, but still didn't work.
I'm stuck now, cannot get into the OS nor the recovery. Any suggestion as to what to do?
Thank you.
Click to expand...
Click to collapse
Format Data from twrp sometime corrupts the file system and brick the phone. (It's happened to me once)
The best way is to flash official firmware via odin and start from there.
I see - I'll try re-flashing the official rom. Btw, would you recommend CWM recovery instead then? Honestly, I'm not very proficient with this whole thing. The reason why I formatted was because I still could see all of my old folders in the phone memory. So I thought Factory Reset didn't really clean up my old rom data.
What do I have to do if I want to start with a really clean slate with CM13 (after reflashing the official one first)?
Also, I still have the issue of CM13 setup being stuck at the Software Update step (right after Wifi setup). Any clue why that happened?
Thanks for taking the time to reply.
vizavalk said:
I see - I'll try re-flashing the official rom. Btw, would you recommend CWM recovery instead then? Honestly, I'm not very proficient with this whole thing. The reason why I formatted was because I still could see all of my old folders in the phone memory. So I thought Factory Reset didn't really clean up my old rom data.
What do I have to do if I want to start with a really clean slate with CM13 (after reflashing the official one first)?
Also, I still have the issue of CM13 setup being stuck at the Software Update step (right after Wifi setup). Any clue why that happened?
Thanks for taking the time to reply.
Click to expand...
Click to collapse
CWM is outdated. Your best bet is TWRP. Try version 3.0.0.
Factory reset doesn't wipe your internal memory, if that's what you mean, you will have to do it manually.
Also, I recommend wiping data, cache, dalvik and system partitions manually from the advanced wipe menu. Factory reset only wipes data and caches, not system.
Oh, and about that stuck at setup issue, just skip that step if possible, you can still change that crap later
If you are unable to set up the ROM, you could flash back to a completely stock ROM and start over.
OK, I'm back on stock Android now.
Before I try flashing CM13 again, I just need suggestions about these two issues I had from previous try:
Unfortunately, Google Play Store has stopped
I have searched for similar issues but can't quite pinpoint the cause. I used the correct GApps for my device and I also removed my SD card prior to installing.
Stuck on Check Connection/Software Update step
Last time I was stuck at this point and, responding to GDReaper, this step couldn't be skipped. The option was grayed out.
vizavalk said:
OK, I'm back on stock Android now.
Before I try flashing CM13 again, I just need suggestions about these two issues I had from previous try:
Unfortunately, Google Play Store has stopped
I have searched for similar issues but can't quite pinpoint the cause. I used the correct GApps for my device and I also removed my SD card prior to installing.
Stuck on Check Connection/Software Update step
Last time I was stuck at this point and, responding to GDReaper, this step couldn't be skipped. The option was grayed out.
Click to expand...
Click to collapse
The sd card has nothing to do with it.
Sometimes gapps don't work on certain roms.
Just try another package.
If you use A-Gapps, the whole first time setup step will be skipped altogether. So that means that you won't run into the risk of getting stuck at that step again.
Or, after flashing the rom, you could use the recovery file manager to delete the setupwizard.apk after you flashed gapps. That should also prevent the initial setup process from initializing at first boot.
vizavalk said:
OK, I'm back on stock Android now.
Before I try flashing CM13 again, I just need suggestions about these two issues I had from previous try:
Unfortunately, Google Play Store has stopped
I have searched for similar issues but can't quite pinpoint the cause. I used the correct GApps for my device and I also removed my SD card prior to installing.
Stuck on Check Connection/Software Update step
Last time I was stuck at this point and, responding to GDReaper, this step couldn't be skipped. The option was grayed out.
Click to expand...
Click to collapse
You probably used Opengapps. That also gives me a lot of errors.
Use Bankgs Gapps instead. They always work for me.
http://download.dirtyunicorns.com/files/gapps/banks_gapps/
GDReaper said:
The sd card has nothing to do with it.
Sometimes gapps don't work on certain roms.
Just try another package.
If you use A-Gapps, the whole first time setup step will be skipped altogether. So that means that you won't run into the risk of getting stuck at that step again.
Or, after flashing the rom, you could use the recovery file manager to delete the setupwizard.apk after you flashed gapps. That should also prevent the initial setup process from initializing at first boot.
Click to expand...
Click to collapse
I used Open GApps, as was recommended in the CM13 post. So are you saying that my two issues were caused solely by the GApps? Because I thought me being stuck at Software Update was due to something else.
Lennyz1988 said:
You probably used Opengapps. That also gives me a lot of errors.
Use Bankgs Gapps instead. They always work for me.
http://download.dirtyunicorns.com/files/gapps/banks_gapps/
Click to expand...
Click to collapse
There are two files - one says Dynamic. But the file sizes are exactly the same. Is there any difference?
vizavalk said:
I used Open GApps, as was recommended in the CM13 post. So are you saying that my two issues were caused solely by the GApps? Because I thought me being stuck at Software Update was due to something else.
There are two files - one says Dynamic. But the file sizes are exactly the same. Is there any difference?
Click to expand...
Click to collapse
Not that I know. Just pick the one without Dynamic.
vizavalk said:
I used Open GApps, as was recommended in the CM13 post. So are you saying that my two issues were caused solely by the GApps? Because I thought me being stuck at Software Update was due to something else.
Click to expand...
Click to collapse
The initial setup process is related to gapps. And I don't recall there being any software update requests during the initial setup. It tells me to wait while it scans for network and WiFis, but I always skip those steps.
Open gapps sometimes work and sometimes they don't. It varies from day to day, since they are updated daily.
Just find a gapps package that works and stick to it until another version of android.
I just want to report back that my CM13 works perfectly with Banks GApps. Thanks to everyone who has helped!
Related
I made the mistake of encrypting my phone and am now paying the price. It is rooted and I had installed the Google Edition 4.4.2 ROM by Danvdh, Kryten2k35 & Ktoonsez. I'm using TWRP 2.7.0.1.
I first tried going into recovery and doing a factory reset and got the an "Unable to mount '/data'" error, followed by a big red FAIL. So I rebooted into the system and tried to do a factory reset from there. Went through all the steps, phone rebooted into recovery and I got the same error - unable to mount.
So I did a bit of searching on the forums here and someone had suggested using the format option in TWRP. So I did that and it seemed to work - did not get the dreaded unable to mount error. So I tried flashing the new rom (the updated version from a couple of weeks ago). Got a message indicating it was successful. Rebooted, and to my dismay, got the prompt for the encryption password. Saw the little line drawing Android, then... nothing - I found myself in brick land.
Managed to get back into TWRP and, based on another post I found, tried Advanced Wipe, selecting everything except Micro SDcard and USB-OTG. Tried installing the new ROM again, says successful, but nothing has changed - I still boot into blackness after inputting my encryption password.
Not sure what else to try. Any suggestions would be most appreciated.
not_su said:
I made the mistake of encrypting my phone and am now paying the price. It is rooted and I had installed the Google Edition 4.4.2 ROM by Danvdh, Kryten2k35 & Ktoonsez. I'm using TWRP 2.7.0.1.
I first tried going into recovery and doing a factory reset and got the an "Unable to mount '/data'" error, followed by a big red FAIL. So I rebooted into the system and tried to do a factory reset from there. Went through all the steps, phone rebooted into recovery and I got the same error - unable to mount.
So I did a bit of searching on the forums here and someone had suggested using the format option in TWRP. So I did that and it seemed to work - did not get the dreaded unable to mount error. So I tried flashing the new rom (the updated version from a couple of weeks ago). Got a message indicating it was successful. Rebooted, and to my dismay, got the prompt for the encryption password. Saw the little line drawing Android, then... nothing - I found myself in brick land.
Managed to get back into TWRP and, based on another post I found, tried Advanced Wipe, selecting everything except Micro SDcard and USB-OTG. Tried installing the new ROM again, says successful, but nothing has changed - I still boot into blackness after inputting my encryption password.
Not sure what else to try. Any suggestions would be most appreciated.
Click to expand...
Click to collapse
Can you go into download mode, revert back to a stock rom (or flash a stock one or something) and turn encryption off? edit: on further research it looks like the only way to completely unencrypt is to reset your device. dunno if that's something you'd want to try, but considering you already wiped multiple times.. i'd say try it?
Also what carrier do you have? That's pretty important. AT&Ts i337 and Verizon's variant cannot flash AOSP roms (more specifically, kernels) due to the bootloader being locked. That might be the issue you're experiencing? I looked up the ROM and it's using ktoonsez kernel, so I imagine that'd be why. Someone just made a version that does not include the kernel and has multiple issues the ROM you're trying to use fixed here.
Rhymey said:
Can you go into download mode, revert back to a stock rom (or flash a stock one or something) and turn encryption off? edit: on further research it looks like the only way to completely unencrypt is to reset your device. dunno if that's something you'd want to try, but considering you already wiped multiple times.. i'd say try it?
Thanks - that's exactly what I've been trying to do. I haven't tried reflashing back to stock with Odin though. Hmmm...
Also what carrier do you have? That's pretty important. AT&Ts i337 and Verizon's variant cannot flash AOSP roms (more specifically, kernels) due to the bootloader being locked. That might be the issue you're experiencing? I looked up the ROM and it's using ktoonsez kernel, so I imagine that'd be why. Someone just made a version that does not include the kernel and has multiple issues the ROM you're trying to use fixed here.
Click to expand...
Click to collapse
Bell, up here in the Great White North. I don't think locked bootloader is an issue - I was on the previous version of Danvdh's ROM, and everything was hunkydory. I just made the unfortunate decision to encrypt. Big mistake.
May try flashing back to stock. Nothing to lose, at this stage...
Thanks!
Hey just wanted to mention for the benefit of anyone else who got into this bind, flashing back to stock using Odin did the trick. Still wouldn't boot, but then I rebooted into stock recovery and did a factory reset, and finally was able to reboot back into stock. What a nightmare. Ugh. Thanks for the tip though - never occurred to me to try to go back to stock. Lesson learned though - no more encryption for me!
not_su said:
Hey just wanted to mention for the benefit of anyone else who got into this bind, flashing back to stock using Odin did the trick. Still wouldn't boot, but then I rebooted into stock recovery and did a factory reset, and finally was able to reboot back into stock. What a nightmare. Ugh. Thanks for the tip though - never occurred to me to try to go back to stock. Lesson learned though - no more encryption for me!
Click to expand...
Click to collapse
Good to hear. Should be able to flash to the rom once again no problem now that it's unencrypted!
Hi
I reflashed my S5 with a stock rom to remove all the Carrier blocks and extras. After the flash the device booted up and instantly came up with the error saying acore has stopped working and then around around 5-10 seconds the phone reboots and does it again. What can I do?
Thanks
Wildey1771 said:
Hi
I reflashed my S5 with a stock rom to remove all the Carrier blocks and extras. After the flash the device booted up and instantly came up with the error saying acore has stopped working and then around around 5-10 seconds the phone reboots and does it again. What can I do?
Thanks
Click to expand...
Click to collapse
Data factory reset in recovery.
Wildey1771 said:
I reflashed my S5 with a stock rom to remove all the Carrier blocks and extras. After the flash the device booted up and instantly came up with the error saying acore has stopped working and then around around 5-10 seconds the phone reboots and does it again. What can I do?
Click to expand...
Click to collapse
It's hard to answer since you provided no crucial details about your phone, configuration or how you flashed it.
You didn't tell us which S5 model you have or your carrier. Nor what firmware file you flashed, so we don't know if it was a compatible file. No Odin log, so we don't know if the flash had errors or not. And you didn't describe how you flashed step by step so we don't know if you missed essential steps.
At a guess, try wiping the partition cache from recovery mode. Then if necessary, do a factory data reset as well (will delete user files!). If you have ongoing problems, then you should restore your backup and try again from that stable condition.
No backup? That is a bad habit to say the least. In that case, flash a full stock firmware image that matches the carrier that the phone was originally sold for.
.
fffft said:
It's hard to answer since you provided no crucial details about your phone, configuration or how you flashed it.
You didn't tell us which S5 model you have or your carrier. Nor what firmware file you flashed, so we don't know if it was a compatible file. No Odin log, so we don't know if the flash had errors or not. And you didn't describe how you flashed step by step so we don't know if you missed essential steps.
At a guess, try wiping the partition cache from recovery mode. Then if necessary, do a factory data reset as well (will delete user files!). If you have ongoing problems, then you should restore your backup and try again from that stable condition.
No backup? That is a bad habit to say the least. In that case, flash a full stock firmware image that matches the carrier that the phone was originally sold for.
.
Click to expand...
Click to collapse
The Model is SM G900F. Its On Three Carrier. I Flashed A STOCK (From SamMobile) Firmware 4.2.2.
The Flash Process Was Successful. No Errors.
Put Device In Download Mode
Connected To Computer
Loaded Firmware Into PDA
Ftime reset
Auto Reboot
Started The Flashing.
Completed.
Phone rebooted. Got Acore has stopped. Then the phone reboots.
But since I needed my phone working quickly I took the path of factory reset and that seems to have fixed it. I did try clearing the cache but no effect.
I believe I know the issue. I used a launcher called Themer. I have reasons to think that was causing the issue because as it was loading in the background I managed to quickly hit the continue button to close the crashed process boxes and as the Launcher finished "Loading" it when it rebooted.
WARNING FOR OTHERS. Always Remove Other Launchers Before Flashing As A Precaution! (Warnings From Newbies Hehe)
I'm not sure what happened with my US Axon 7. I was getting it ready to give to my son, and now it won't boot. Even with a full wipe (including system) and reinstall of the OS. It tries to boot, but just sits at the Google animation forever.
Here is basically the steps of what happened during the wipe/install of the unofficial RR Oreo build:
- Wiped everything
- Flashed the B32+B10 bootstack (A2017X_BootStack_B32+B10.zip)
- Flashed the latest (at the time) unofficial RR Oreo build (RR-O-v6.0.0-20180511-axon7-Unofficial.zip)
- Flashed opengapps micro (open_gapps-arm64-8.1-micro-20180512.zip)
- Flashed Magisk 16.0 (Magisk-v16.0.zip)
- Booted up and setup the phone for his google account
- Rebooted multiple times during setup
- Installed TiBu and froze the apps I normally freeze for the kids.... things they don't need
- Rebooted one final time and got stuck on the boot screen
- Re-performed steps above (minus setup... because I still can't get it to boot)
The best I can figure is that I froze something I shouldn't have... but a wipe and reinstall should have fixed that. I don't understand why it wouldn't. I've even wiped system.
I'm going to see if I saved a backup somewhere, as it's not on the phone. I can still get into recovery and such, which is good.
Flapjack said:
I'm not sure what happened with my US Axon 7. I was getting it ready to give to my son, and now it won't boot. Even with a full wipe (including system) and reinstall of the OS. It tries to boot, but just sits at the Google animation forever.
Here is basically the steps of what happened during the wipe/install of the unofficial RR Oreo build:
- Wiped everything
- Flashed the B32+B10 bootstack (A2017X_BootStack_B32+B10.zip)
- Flashed the latest (at the time) unofficial RR Oreo build (RR-O-v6.0.0-20180511-axon7-Unofficial.zip)
- Flashed opengapps micro (open_gapps-arm64-8.1-micro-20180512.zip)
- Flashed Magisk 16.0 (Magisk-v16.0.zip)
- Booted up and setup the phone for his google account
- Rebooted multiple times during setup
- Installed TiBu and froze the apps I normally freeze for the kids.... things they don't need
- Rebooted one final time and got stuck on the boot screen
- Re-performed steps above (minus setup... because I still can't get it to boot)
The best I can figure is that I froze something I shouldn't have... but a wipe and reinstall should have fixed that. I don't understand why it wouldn't. I've even wiped system.
I'm going to see if I saved a backup somewhere, as it's not on the phone. I can still get into recovery and such, which is good.
Click to expand...
Click to collapse
Which apps do you freeze? If you froze some Google apps you can just use the pico package and avoid having to use TiBU entirely
You're saying that after doing the whole installation you set up the ROM, but after you freeze apps with titanium and reboot the phone refuses to boot?
Choose an username... said:
Which apps do you freeze? If you froze some Google apps you can just use the pico package and avoid having to use TiBU entirely
Click to expand...
Click to collapse
I don't remember exactly... nothing I haven't frozen on their phones before.
You're saying that after doing the whole installation you set up the ROM, but after you freeze apps with titanium and reboot the phone refuses to boot?
Click to expand...
Click to collapse
It seems to be that way. I had already installed Magisk, but it's not like I installed Xposed or anything "dangerous" to the operation of the phone. The only thing I can think of is I froze something that kept it from booting. But if that's the case, why wouldn't reinstalling the ROM fix it? Wouldn't that fix anything I changed/froze?
Flapjack said:
I don't remember exactly... nothing I haven't frozen on their phones before.
It seems to be that way. I had already installed Magisk, but it's not like I installed Xposed or anything "dangerous" to the operation of the phone. The only thing I can think of is I froze something that kept it from booting. But if that's the case, why wouldn't reinstalling the ROM fix it? Wouldn't that fix anything I changed/froze?
Click to expand...
Click to collapse
well, if you wiped and installed everything again it should work...
Something must have been wrong with the ROM itself. I don't get it, since it worked fine the first install. I installed AOSP instead and it booted right up. I'm going to take a full backup, freeze the things I normally freeze, then see what happens.
I was having a very similar issue while trying to move to exactly the same ROM. My problem was that I was accidentally encrypting the phone (I didn't realize that this is what the "require pin at startup" prompt was doing). If TWRP is asking you to put in a pin number every time you boot into recovery, then your phone is encrypted. RR ROM (or at least the most common version of it) does not support encryption, so it will refuse to boot.
To get rid of encryption, you have to select the "format data" option in the wipe menu. You can't just wipe the usual partitions.
I can't be certain that this is your issue, but hopefully it helps.
beokabatukaba said:
I was having a very similar issue while trying to move to exactly the same ROM. My problem was that I was accidentally encrypting the phone (I didn't realize that this is what the "require pin at startup" prompt was doing). If TWRP is asking you to put in a pin number every time you boot into recovery, then your phone is encrypted. RR ROM (or at least the most common version of it) does not support encryption, so it will refuse to boot.
To get rid of encryption, you have to select the "format data" option in the wipe menu. You can't just wipe the usual partitions.
I can't be certain that this is your issue, but hopefully it helps.
Click to expand...
Click to collapse
Not similar at all. In your case the ROM would boot fine, but it woupd fail to load your data, so it asks for a password that not necessarily exists. In his case the ROM never gets to boot
Choose an username... said:
Not similar at all. In your case the ROM would boot fine, but it woupd fail to load your data, so it asks for a password that not necessarily exists. In his case the ROM never gets to boot
Click to expand...
Click to collapse
You misunderstand. I could only boot RR once, and if I accidentally encrypted the device during setup or afterward, the next time I tried to restart, it would be stuck on the boot screen. All subsequent reinstalls also got stuck on the boot animation since I wasn't removing encryption even if I wiped data, system, cache, etc. Moving to AEX allowed me to boot with encryption, and it was at that point that I realized my mistake. That sounds precisely like what is happening to flapjack, except that the cause may or may not be the same since he got through multiple boots the first time and presumably had already setup a pin/password on one of the first boots.
Immediately after the pin is setup should be when it asks if you want to require the pin on startup (aka if you want to encrypt), so if he opted to do that after setting everything up rather than on the very first boot, he may have exactly the same issue I had.
I haven't followed development of the 6T since November so please forgive me if this has been answered 100 times.
The steps to flashing custom non-OOS ROM's is to; flash ROM/flash TWRP installer/reboot recovery/flash gapps/flash magisk
The weird issue for me is when I reboot recovery after flashing the ROM and TWRP when I go to install gapps all my files are encrypted. My way around this was to sideload gapps and magisk and everything booted up fine. When I go back to recovery after the first boot all the files are normal again.
This has happened both times I've flashed a ROM.
I'm sure this has an easy answer and it's most likely due to a step I didn't execute properly -- or at all. I did a lot of reading and making sure I understood the process before rooting my device but as far as flashing ROM's I was noticing a lot of conflicting info which I've never seen before on any other device. Anyway, other than this I haven't had any issue.
Thanks for any feedback.
Security issue. Best way around it is to either format data before flashing and/or remove your lockscreen security pin before flashing.
Deleted
ogkillergreen said:
Security issue. Best way around it is to either format data before flashing and/or remove your lockscreen security pin before flashing.
Click to expand...
Click to collapse
I never use any lock. Always just use Swype to unlock. I'm aware of the issue with using a lock though. I read that people had problems. I just haven't seen where any one brought up my exact issue. It doesn't seem to effect anything so I'm not stressing it too bad. Eventually I'll get around to troubleshooting it.
I've flashed almost every ROM for 6T till now and every time I flash a ROM I'm having exactly the same issue as you. I've also tried formatting data several times, but the issue with unreadable data in TWRP after flashing a ROM returns every single time. I've tried multiple combinations of flashing, wiping etc. and it's always the same. However, what I'm doing in such case is flashing gapps + magisk from USB-C pendrive, no need to sideload, just mount USB and flash files from that as usual. After doing that I can boot to ROM and the data is readable again. I just need to remember to have this pendrive close to me when I'm flashing a new ROM.
BreathingWounds said:
I've flashed almost every ROM for 6T till now and every time I flash a ROM I'm having exactly the same issue as you. I've also tried formatting data several times, but the issue with unreadable data in TWRP after flashing a ROM returns every single time. I've tried multiple combinations of flashing, wiping etc. and it's always the same. However, what I'm doing in such case is flashing gapps + magisk from USB-C pendrive, no need to sideload, just mount USB and flash files from that as usual. After doing that I can boot to ROM and the data is readable again. I just need to remember to have this pendrive close to me when I'm flashing a new ROM.
Click to expand...
Click to collapse
Thanks for the tip and info. I don't mind sideloading because it's fast and anytime I mess with my phone it's when I'm at my PC. I've been using adb for so many years it's my go-to whenever my phone is acting stupid.
The second time I flashed a ROM I didn't even worry about flashing gapps, just magisk. And I stacked them. So ROM, TWRP, Magisk. Then rebooted system. I actually prefer this anyway because then you boot straight to the launcher with no setup process. Then I go back and flash GAPPS. I actually have used this flashing process for years because I hate the setup after a first time boot.
Hello.
This is my first post as I've done everything myself till now, but now I'm really lost in some uncharted territory.
All I wanted is to have a second DeGoogled phone and I messed my Samsung Galaxy S5 beyond my understanding
So, I flashed TWRP to my SM-G900F klte through Odin and then installed /e/ ROM through zip method and everything was working fine, then I wanted to flash Intelli kernel, but I got an error saying "Digest failed to match on '/external-sd/Intelli-Kernel-v15-klte.zip'. E: Aborting zip install: Digest verification failed. Error installing zip file '/external_sd/Intelli-Kernel-v15-klte.zip'". I double checked the md5 of TWRP, /e/ and Intelli Kernel zip's, reflashed TWRP, flashed IceMan's TWRP recovery, wiped all partitions, formatted data and re-installed /e/, tried Havoc ROM, but I still got the same message. The problem wasn't only with the kernel, but also with some (not all) other zip's like A2camforS5_TWRP_v1.4.zip and even Magisk (which flashed fine) modules like A2camforS5_Magisk_v2.zip were not flashing (the procedure got through, but once the phone restarted the module wouldn't show up). On my previous SM-G900F klte phone everything was working fine. (And yes, TWPR's check md5 option was disabled, so this wasn't the problem)
After a bit of chatting on Intelli kernel and /e/ Telegram support groups I found out it wasn't the kernel or /e/ problem and that I should go back to stock and start all over. I had a full NANDroid backup from my previous phone so I renamed the backup folder to match the new phone serial (so it would show the partitions to restore in TWRP) and as I (and nobody else) didn't know where the problem was I restored all partitions. Everything went through as it should except modem, which showed an error saying something about being read-only and efs, which went half way through and then gave an error I don't remember (but can reproduce if needed). The phone wouldn't boot to OS (it was stuck on SAMSUNG logo), so I re-flashed TWRP and /e/ again and tried to flash the kernel or other zips but they were still giving me "digestion" problems... but it got worse! Now when I boot to /e/ I'm not even able to use the phone normally as a pop-up saying "Bluetooth app has crashed" and "Bluetooth app keeps crashing" shows up continuously even if Bluetooth as other wireless connection work just fine. Did I mess something up with the unfinished efs restore?
How can I diagnose the problem and unmess my phone? What steps should I take? I'm afraid of bricking my phone if I just start to do random stuff so any useful information would be appreciated! Please help!
EDIT: Even if my description of the procedure looks like I flashed a ton of stuff all at once I have just WRITTEN A RESUME AS CONDENSED AS POSSIBLE - the procedure took me more than a week of flashing ONE THING AT A TIME and testing if everything works fine. At no point in my flashing procedure there were more than three things present on my phone: TWRP, ROM and MAGISK as kernel and camera mod refused to flash anyway. To exclude Magisk being a problem I clean installed everything so I had just TWRP and ROM and I was getting the same problem. Then I reflashed TWRP only, using the IceMan version (because it presumably solves all flashing problems) retested, then flashed /e/ only, retested, Havoc only, retested... well, you got the picture!
I was doing everything under the guidance of Intelli kernel Telegram support group members until I understood the problem was not the kernel, nor TWRP/IceMan, nor /e//Havoc and went with the stock recovery through TWRP and messed my phone beyond Intelli kernel Telegram group's scope.
ShalaMala said:
Hello.
This is my first post as I've done everything myself till now, but now I'm really lost in some uncharted territory.
All I wanted is to have a second DeGoogled phone and I messed my Samsung Galaxy S5 beyond my understanding
So, I flashed TWRP to my SM-G900F klte through Odin and then installed /e/ ROM through zip method and everything was working fine, then I wanted to flash Intelli kernel, but I got an error saying "Digest failed to match on '/external-sd/Intelli-Kernel-v15-klte.zip'. E: Aborting zip install: Digest verification failed. Error installing zip file '/external_sd/Intelli-Kernel-v15-klte.zip'". I double checked the md5 of TWRP, /e/ and Intelli Kernel zip's, reflashed TWRP, flashed IceMan's TWRP recovery, wiped all partitions, formatted data and re-installed /e/, tried Havoc ROM, but I still got the same message. The problem wasn't only with the kernel, but also with some (not all) other zip's like A2camforS5_TWRP_v1.4.zip and even Magisk (which flashed fine) modules like A2camforS5_Magisk_v2.zip were not flashing (the procedure got through, but once the phone restarted the module wouldn't show up). On my previous SM-G900F klte phone everything was working fine.
After a bit of chatting on Intelli kernel and /e/ Telegram support groups I found out it wasn't the kernel or /e/ problem and that I should go back to stock and start all over. I had a full NANDroid backup from my previous phone so I renamed the backup folder to match the new phone serial (so it would show the partitions to restore in TWRP) and as I (and nobody else) didn't know where the problem was I restored all partitions. Everything went through as it should except modem, which showed an error saying something about being read-only and efs, which went half way through and then gave an error I don't remember (but can reproduce if needed). The phone wouldn't boot to OS (it was stuck on SAMSUNG logo), so I re-flashed TWRP and /e/ again and tried to flash the kernel or other zips but they were still giving me "digestion" problems... but it got worse! Now when I boot to /e/ I'm not even able to use the phone normally as a pop-up saying "Bluetooth app has crashed" and "Bluetooth app keeps crashing" shows up continuously even if Bluetooth as other wireless connection work just fine. Did I mess something up with the unfinished efs restore?
How can I diagnose the problem and unmess my phone? What steps should I take? I'm afraid of bricking my phone if I just start to do random stuff so any useful information would be appreciated! Please help!
Click to expand...
Click to collapse
Idk what your phone's actual issue is, but you should probably not have restored efs from previous phone.
At this point, I would probably Odin back to latest stock firmware, to see if the phone will boot and recognize sim card. If so, I would go from there, flash latest official TWRP, format data, and either restore the backup sans modem and efs, or try a different ROM.
DO NOT INSTALL TWRP APP
Also, try to do things in small traceable steps to make it easier to see what is causing your problem.
Eg:
Flash just the bare ROM, nothing else, no Magisk, no hacky crap, just the ROM. Test it.
If everything is satisfactory, then try the next step and test again, working your way up to your desired ROM/kernel/Magisk/apps solution that makes you happy.
For maximum stability it's always preferable to format data (Advanced wipe>format>type yes) when flashing a ROM to ensure a clean slate for everything.
Also, try not too let your phone get too hot with lots of flashing. I've seen good phones do odd stuff when overheated.
That's all the advice I can think of right now, how it is some help to you.
Good luck! :good:
you should probably not have restored efs from previous phone.
Click to expand...
Click to collapse
Yeah, I assume that was the stupidest thing, but an online guide suggested it's ok to restore from another phone's NAND backup as long as it's the same model, so I thought it was safe.
At this point, I would probably Odin back to latest stock firmware, to see if the phone will boot and recognize sim card.
Click to expand...
Click to collapse
My phone works fine with /e/ ROM as before - SIM, Wi-Fi, Bluetooth and all, there is just a constant pop-up saying that the Bluetooth app has crashed interfering with everything I do that wasn't present before the stupid restore to stock.
If so, I would go from there, flash latest official TWRP, format data, and either restore the backup sans modem and efs, or try a different ROM.
Click to expand...
Click to collapse
Did all this except trying a different ROM, because it wasn't producing the Bluetooth app has crashed problem before restoring to stock, so I assumed it's not a ROM problem. The digest problem was present also in Havoc ROM.
DO NOT INSTALL TWRP APP
Click to expand...
Click to collapse
Why? Is this a general issue or just a problem in my case? Anyway I have disabled the option before restarting to system.
Also, try to do things in small traceable steps to make it easier to see what is causing your problem. Eg: Flash just the bare ROM, nothing else, no Magisk, no hacky crap, just the ROM. Test it.
Click to expand...
Click to collapse
Yeah, I was doing the things one step at a time, my message is just a condensed resume of all the steps I did to make it shorter. I stopped adding things once I was unable to flash the kernel, camera mod and Magisk modules - I didn't just add everything I was trying to understand if the problem was just with kernel or my phone wouldn't flash also some other zips.
If everything is satisfactory, then try the next step and test again, working your way up to your desired ROM/kernel/Magisk/apps solution that makes you happy.
Click to expand...
Click to collapse
Yes, yes, that was the plan, but now the bare ROM doesn't want to work anymore without giving me Bluetooth app crashes
For maximum stability it's always preferable to format data (Advanced wipe>format>type yes) when flashing a ROM to ensure a clean slate for everything.
Click to expand...
Click to collapse
I did that before every flash.
Also, try not too let your phone get too hot with lots of flashing. I've seen good phones do odd stuff when overheated.
Click to expand...
Click to collapse
Good to know!
That's all the advice I can think of right now, how it is some help to you. Good luck!
Click to expand...
Click to collapse
Thank you. So now I flashed the latest .tar.md5 file for my model and my CSC through Odin and the phone wouldn't boot to stock ROM (I guess because it had /e/ Pie on it already and the latest stock ROM is just Marshmallow so it's considered downgrading), got stuck at SAMSUNG logo and phone went extremely hot. I pulled out the battery, went in download mode, flashed TWRP, wiped all partitions, formatted data, flashed /e/, booted /e/, the message about Bluetooth app crashing persists, went to TWRP, tried to flash Intelli kernel, got the "digest" error, tried camera mod, got "digest error" again, magisk flashed fine, so flashing works... so what now? I checked inside the .tar.md5 file and there is no efs partition so I guess it wasn't written over by flashing through Odin
Should the phone be able to boot to stock? Is that even necessary - would it fix anything?
ShalaMala said:
My phone works fine with /e/ ROM as before - SIM, Wi-Fi, Bluetooth and all, there is just a constant pop-up saying that the Bluetooth app has crashed interfering with everything I do that wasn't present before the stupid restore to stock.
Click to expand...
Click to collapse
"If so, I would go from there, flash latest official TWRP, format data, and either restore the backup sans modem and efs, or try a different ROM."
A: Did all this except trying a different ROM, because it wasn't producing the Bluetooth app has crashed problem before restoring to stock, so I assumed it's not a ROM problem. The digest problem was present also in Havoc ROM.
Click to expand...
Click to collapse
Maybe try flashing just the baseband with latest modem, etc from haggertk's archive on AFH, here:
https://androidfilehost.com/?w=files&flid=59628
You can flash that without wiping and it only touches the baseband/firmware files, so should not affect anything else
"DO NOT INSTALL TWRP APP"
A: Why? Is this a general issue or just a problem in my case? Anyway I have disabled the option before restarting to system.
Click to expand...
Click to collapse
It's a general issue. The app is bloatware and is known to sometimes cause bootloops see @curiousrom 's post here:
TWRP App Causing Bootloop or Fail To Boot
It's frustrating that TWRP is setup to facilitate easy swiping to install the app
A: Thank you. So now I flashed the latest .tar.md5 file for my model and my CSC through Odin and the phone wouldn't boot to stock ROM (I guess because it had /e/ Pie on it already and the latest stock ROM is just Marshmallow so it's considered downgrading), got stuck at SAMSUNG logo and phone went extremely hot.
Click to expand...
Click to collapse
Unlikely due to /e/ ROM, I have had this happen before. Just pulled battery, hold power button with no battery or charge cable for at least 10 sec to clear remaining charge (I have one phone that will get itself so out of shape that I have to leave it overnight with no battery before it will boot), let it cool, reinstalled battery and try again. Usually it will boot after this.
I pulled out the battery, went in download mode, flashed TWRP, wiped all partitions, formatted data, flashed /e/, booted /e/, the message about Bluetooth app crashing persists, went to TWRP, tried to flash Intelli kernel, got the "digest" error, tried camera mod, got "digest error" again, magisk flashed fine, so flashing works... so what now? I checked inside the .tar.md5 file and there is no efs partition so I guess it wasn't written over by flashing through Odin
Should the phone be able to boot to stock? Is that even necessary - would it fix anything?
Click to expand...
Click to collapse
Flashing stock ROM can sometimes help fix EFS issues, so that is why I suggested that. I also like to see the stock ROM boot with all functions working to make sure the hardware is ok.
I don't assume you haven't done any of the things I suggest. I'm just brainstorming to see if I can help you from my personal experience with my S5s.
Hope you can get yours working:good:
Maybe try flashing just the baseband with latest modem, etc from haggertk's archive on AFH, here:
androidfilehost.com/?w=files&flid=59628
Click to expand...
Click to collapse
I'm reading some instructions: ohthehugemanatee.org/blog/2015/04/04/how-and-why-to-update-the-modem-slash-baseband-firmware-on-a-samsung-phone about how to flash baseband as this is something I've never done before and I'm afraid to mess my device even further... They say "Note that each carrier handles their own updates, so they package their own modem firmwares with slightly different serial numbers. There shouldn’t be any significant difference, but check which one comes from your country and provider".
So I searched for the CSC of the firmware you've linked and it seems to be XXU: samfrew.com/download/GALAXY__S5__/1l88/BTU/G900FXXU1CRH1/G900FOXA1CRH1, which turns out to be a "Multi-CSC for some of the countries and regions (“O” refers to Open)"... is that "some" that bothers me as XXU is not listed under my country's CSC list.
Should I worry? Is it possible to try out if this baseband solves my problems and if it will not work return to the previous version flashing the stock ROM again or am I risking to brick my phone? I didn't find a baseband for my country's csc (SIO) as I will not be receiving any official updates anymore should I change my phone's CSC to XXU first?
(I'm not able to post URL's yet, so they are truncated.)