Related
Hi guys, I am new here, I am now finding help anywhere about my Note III recent problem...
My note III is SM-N9005 Malaysia version, I did root it with CF Auto Root and I had been using it without problems until yesterday morning,
This is my case :
I realized my alarm was written "Clock has been not responding" and I lost my network service, then I tried to restart my phone,
Since I restart, it became worst, my phone went into boot loop and sometimes freeze on the "Samsung Galaxy Note 3" screen,
But in a few times of reboot, it will be able to boot into homescreen, but still no service for the network, and everything processes work extremely slow, even freezing and crashing!
What I tried to do to fix it :
-I went to the Samsung service center, and the technician said that my warranty is voided (Ofcourse I knew it), and he told me that this problem is due to software problem instead of hardware.
-I did flash my kernel with stock kernel again which was downloaded from Sammobile, but it did not fix my problem,
-And I tried to hard reset and factory reset of my phone, it did not help too,
-I am also tried to clear cache and dalvik cache and reboot the device, it didn't seems working...
I have already done what I could but I still yet to fix my phone, what should I do now, any experts can guild me?? T^T
Thank you
KelvinEclipse said:
Hi guys, I am new here, I am now finding help anywhere about my Note III recent problem...
My note III is SM-N9005 Malaysia version, I did root it with CF Auto Root and I had been using it without problems until yesterday morning,
This is my case :
I realized my alarm was written "Clock has been not responding" and I lost my network service, then I tried to restart my phone,
Since I restart, it became worst, my phone went into boot loop and sometimes freeze on the "Samsung Galaxy Note 3" screen,
But in a few times of reboot, it will be able to boot into homescreen, but still no service for the network, and everything processes work extremely slow, even freezing and crashing!
What I tried to do to fix it :
-I went to the Samsung service center, and the technician said that my warranty is voided (Ofcourse I knew it), and he told me that this problem is due to software problem instead of hardware.
-I did flash my kernel with stock kernel again which was downloaded from Sammobile, but it did not fix my problem,
-And I tried to hard reset and factory reset of my phone, it did not help too,
-I am also tried to clear cache and dalvik cache and reboot the device, it didn't seems working...
I have already done what I could but I still yet to fix my phone, what should I do now, any experts can guild me?? T^T
Thank you
Click to expand...
Click to collapse
have you done a EFS backup? it helps if you run into problems like this....
check here...http://forum.xda-developers.com/showthread.php?t=2298104
this works on note 8 though
welard said:
have you done a EFS backup? it helps if you run into problems like this....
check here...http://forum.xda-developers.com/showthread.php?t=2298104
this works on note 8 though
Click to expand...
Click to collapse
I didn't really know about EFS while I root my phone, I just knew it recently due to my current issue, so I didn't backup it....
Is there any other solution??? Or could I recover my EFS eventhough I didn't do a backup??
BTW, thx for reply~
KelvinEclipse said:
I didn't really know about EFS while I root my phone, I just knew it recently due to my current issue, so I didn't backup it....
Is there any other solution??? Or could I recover my EFS eventhough I didn't do a backup??
BTW, thx for reply~
Click to expand...
Click to collapse
check your internal card or sd card for a folder called Backups or something similar, if your running a custom rom normally EFS is automatically stored there if your custom rom does do EFS backup automatically at install....if not do a search on the forum for EFS RECOVERY or re-flash your rom it may help or may not, but im sure it wont though...
also read though the link i sent you there maybe some think there that may help you
you can try to do install new firmware with odin 3:09 kitkate see how it behaves ....
ANDROIDXFOREVER said:
you can try to do install new firmware with odin 3:09 kitkate see how it behaves ....
Click to expand...
Click to collapse
Its not bricked if its still working. Have you tried turning on your phone without a sim card / sd card inserted?
also try *#06# to see if your imei number is presant..
try flashing stock rom
in the same boat hope u get it sorted, i just flashed the omega v14 onto my note and its stuck on the first screen
yulaw5110 said:
in the same boat hope u get it sorted, i just flashed the omega v14 onto my note and its stuck on the first screen
Click to expand...
Click to collapse
Reboot into recovery and wipe cache partition and then scroll to advanced and wipe dalvik cache, then reboot your phone
Sent from my SM-N9005 using XDA Premium 4 mobile app
Thanks guys for the replies
-I went for a search for the backup folder in either of the storage mentioned by I didn't see a file called "backup"... I think I deleted it since the factory reset I've done yesterday, I went to many forums hat talk about EFS, and it wont help my problem cos all of them are talk about "Backup/recover", where I didn't backup my EFS earlier...
-I tried for the IMEI code, that's the reason I know about EFS, it shows "null/null", and most the information are showing unknown, such as baseband version, IMEISV, IP Address, Bluetooth Address.
-My current situation is whatever I flash into my phone, it just wont help, the problem didn't improvise at all...
Thanks..
KelvinEclipse said:
Thanks guys for the replies
-I went for a search for the backup folder in either of the storage mentioned by I didn't see a file called "backup"... I think I deleted it since the factory reset I've done yesterday, I went to many forums hat talk about EFS, and it wont help my problem cos all of them are talk about "Backup/recover", where I didn't backup my EFS earlier...
-I tried for the IMEI code, that's the reason I know about EFS, it shows "null/null", and most the information are showing unknown, such as baseband version, IMEISV, IP Address, Bluetooth Address.
-My current situation is whatever I flash into my phone, it just wont help, the problem didn't improvise at all...
Thanks..
Click to expand...
Click to collapse
download Stock firmware from sammobile or samsung updates
turn phone off, boot into recovery mode wipe data/factory reset, wipe cache partition
turn phone off, boot into download mode
use odin v 3.09 load your downloaded firmware into AP, check update boot loader box, don't check anything else and click start.
once it finishes flashing, it will reboot by itself.
if it fails then you might want to repeat the process above one more time.
if still fails u might want to do emergency recovery via kies.
Good luck and hope this helps.
doodydood said:
download Stock firmware from sammobile or samsung updates
turn phone off, boot into recovery mode wipe data/factory reset, wipe cache partition
turn phone off, boot into download mode
use odin v 3.09 load your downloaded firmware into AP, check update boot loader box, don't check anything else and click start.
once it finishes flashing, it will reboot by itself.
if it fails then you might want to repeat the process above one more time.
if still fails u might want to do emergency recovery via kies.
Good luck and hope this helps.
Click to expand...
Click to collapse
Thanks for the reply
I have tried the odin method and it didn't work...
Now I am trying for the kies emergency recovery method, and I will reply if there are any improvements...
Hi guys, I think have some new clues to determine my problem now
I flashed a custom recovery into my phone this morning,
and I realise that my /system, /efs and /firmware-modem is unmounted,
I tried to mount them, it was successful, but when I reboot the device, the problem still there,
Boot loop, no IMEI, no Baseband Version, Lag Processes,
and I went back to recovery again, I realised they have been unmounted again...
Any idea what is the problem guys??
Thx
doodydood said:
download Stock firmware from sammobile or samsung updates
turn phone off, boot into recovery mode wipe data/factory reset, wipe cache partition
turn phone off, boot into download mode
use odin v 3.09 load your downloaded firmware into AP, check update boot loader box, don't check anything else and click start.
once it finishes flashing, it will reboot by itself.
if it fails then you might want to repeat the process above one more time.
if still fails u might want to do emergency recovery via kies.
Good luck and hope this helps.
Click to expand...
Click to collapse
Hi there,
I have tried the kies emergency recovery method, but it was unsuccessful,
My note 3 was connected to the kies, but when I run Emergency Firmware Recovery,
My device was instantly disconnected with kies
And I have also tried the Firmware Upgrade and Initialisation,
The Kies showed me that my device is not supported with initialisation...
Anything I should do??
Thx
speedyjay said:
Reboot into recovery and wipe cache partition and then scroll to advanced and wipe dalvik cache, then reboot your phone
Sent from my SM-N9005 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
i actually found a different kernal in the omega thread and that seemed to sort it, thanks tho
My i9505 was running stock KitKat from Samsung and I tried to install CM13 ROM.
So I used Odin to root the phone and installed TWRP 2.8.6.0. After that I flashed the CM13 ROM and the Gapps Nano.
I got as far as rebooting into CM13. But then the "Google Play Store has stopped working" message keeps popping up starting from the initial setup phase. I ignored the message and went on to setup the wifi but couldn't progress any further. The wifi was detected and connected but then it was stuck on the Checking Connection/Software Update step.
I tried to reflash the rom and gapps again to no avail. The third time to Format Data from TWRP before reflashing - still didn't make a difference.
What's worst is now I cannot even get into TWRP! Whenever I press Vol Up + Power + Home, it will show the small 'entering recovery' message momentarily on the top left corner but then it phone simply restarted again.
I tried re-flashing TWRP using Odin, but still didn't work.
I'm stuck now, cannot get into the OS nor the recovery. Any suggestion as to what to do?
Thank you.
vizavalk said:
My i9505 was running stock KitKat from Samsung and I tried to install CM13 ROM.
So I used Odin to root the phone and installed TWRP 2.8.6.0. After that I flashed the CM13 ROM and the Gapps Nano.
I got as far as rebooting into CM13. But then the "Google Play Store has stopped working" message keeps popping up starting from the initial setup phase. I ignored the message and went on to setup the wifi but couldn't progress any further. The wifi was detected and connected but then it was stuck on the Checking Connection/Software Update step.
I tried to reflash the rom and gapps again to no avail. The third time to Format Data from TWRP before reflashing - still didn't make a difference.
What's worst is now I cannot even get into TWRP! Whenever I press Vol Up + Power + Home, it will show the small 'entering recovery' message momentarily on the top left corner but then it phone simply restarted again.
I tried re-flashing TWRP using Odin, but still didn't work.
I'm stuck now, cannot get into the OS nor the recovery. Any suggestion as to what to do?
Thank you.
Click to expand...
Click to collapse
Format Data from twrp sometime corrupts the file system and brick the phone. (It's happened to me once)
The best way is to flash official firmware via odin and start from there.
I see - I'll try re-flashing the official rom. Btw, would you recommend CWM recovery instead then? Honestly, I'm not very proficient with this whole thing. The reason why I formatted was because I still could see all of my old folders in the phone memory. So I thought Factory Reset didn't really clean up my old rom data.
What do I have to do if I want to start with a really clean slate with CM13 (after reflashing the official one first)?
Also, I still have the issue of CM13 setup being stuck at the Software Update step (right after Wifi setup). Any clue why that happened?
Thanks for taking the time to reply.
vizavalk said:
I see - I'll try re-flashing the official rom. Btw, would you recommend CWM recovery instead then? Honestly, I'm not very proficient with this whole thing. The reason why I formatted was because I still could see all of my old folders in the phone memory. So I thought Factory Reset didn't really clean up my old rom data.
What do I have to do if I want to start with a really clean slate with CM13 (after reflashing the official one first)?
Also, I still have the issue of CM13 setup being stuck at the Software Update step (right after Wifi setup). Any clue why that happened?
Thanks for taking the time to reply.
Click to expand...
Click to collapse
CWM is outdated. Your best bet is TWRP. Try version 3.0.0.
Factory reset doesn't wipe your internal memory, if that's what you mean, you will have to do it manually.
Also, I recommend wiping data, cache, dalvik and system partitions manually from the advanced wipe menu. Factory reset only wipes data and caches, not system.
Oh, and about that stuck at setup issue, just skip that step if possible, you can still change that crap later
If you are unable to set up the ROM, you could flash back to a completely stock ROM and start over.
OK, I'm back on stock Android now.
Before I try flashing CM13 again, I just need suggestions about these two issues I had from previous try:
Unfortunately, Google Play Store has stopped
I have searched for similar issues but can't quite pinpoint the cause. I used the correct GApps for my device and I also removed my SD card prior to installing.
Stuck on Check Connection/Software Update step
Last time I was stuck at this point and, responding to GDReaper, this step couldn't be skipped. The option was grayed out.
vizavalk said:
OK, I'm back on stock Android now.
Before I try flashing CM13 again, I just need suggestions about these two issues I had from previous try:
Unfortunately, Google Play Store has stopped
I have searched for similar issues but can't quite pinpoint the cause. I used the correct GApps for my device and I also removed my SD card prior to installing.
Stuck on Check Connection/Software Update step
Last time I was stuck at this point and, responding to GDReaper, this step couldn't be skipped. The option was grayed out.
Click to expand...
Click to collapse
The sd card has nothing to do with it.
Sometimes gapps don't work on certain roms.
Just try another package.
If you use A-Gapps, the whole first time setup step will be skipped altogether. So that means that you won't run into the risk of getting stuck at that step again.
Or, after flashing the rom, you could use the recovery file manager to delete the setupwizard.apk after you flashed gapps. That should also prevent the initial setup process from initializing at first boot.
vizavalk said:
OK, I'm back on stock Android now.
Before I try flashing CM13 again, I just need suggestions about these two issues I had from previous try:
Unfortunately, Google Play Store has stopped
I have searched for similar issues but can't quite pinpoint the cause. I used the correct GApps for my device and I also removed my SD card prior to installing.
Stuck on Check Connection/Software Update step
Last time I was stuck at this point and, responding to GDReaper, this step couldn't be skipped. The option was grayed out.
Click to expand...
Click to collapse
You probably used Opengapps. That also gives me a lot of errors.
Use Bankgs Gapps instead. They always work for me.
http://download.dirtyunicorns.com/files/gapps/banks_gapps/
GDReaper said:
The sd card has nothing to do with it.
Sometimes gapps don't work on certain roms.
Just try another package.
If you use A-Gapps, the whole first time setup step will be skipped altogether. So that means that you won't run into the risk of getting stuck at that step again.
Or, after flashing the rom, you could use the recovery file manager to delete the setupwizard.apk after you flashed gapps. That should also prevent the initial setup process from initializing at first boot.
Click to expand...
Click to collapse
I used Open GApps, as was recommended in the CM13 post. So are you saying that my two issues were caused solely by the GApps? Because I thought me being stuck at Software Update was due to something else.
Lennyz1988 said:
You probably used Opengapps. That also gives me a lot of errors.
Use Bankgs Gapps instead. They always work for me.
http://download.dirtyunicorns.com/files/gapps/banks_gapps/
Click to expand...
Click to collapse
There are two files - one says Dynamic. But the file sizes are exactly the same. Is there any difference?
vizavalk said:
I used Open GApps, as was recommended in the CM13 post. So are you saying that my two issues were caused solely by the GApps? Because I thought me being stuck at Software Update was due to something else.
There are two files - one says Dynamic. But the file sizes are exactly the same. Is there any difference?
Click to expand...
Click to collapse
Not that I know. Just pick the one without Dynamic.
vizavalk said:
I used Open GApps, as was recommended in the CM13 post. So are you saying that my two issues were caused solely by the GApps? Because I thought me being stuck at Software Update was due to something else.
Click to expand...
Click to collapse
The initial setup process is related to gapps. And I don't recall there being any software update requests during the initial setup. It tells me to wait while it scans for network and WiFis, but I always skip those steps.
Open gapps sometimes work and sometimes they don't. It varies from day to day, since they are updated daily.
Just find a gapps package that works and stick to it until another version of android.
I just want to report back that my CM13 works perfectly with Banks GApps. Thanks to everyone who has helped!
Hi!
Just got myself Note 4, and after rooting and installing TWRP I started looking for ROM that fits my needs. And here goes the strange thing - after tryign few ROMs, now the only ones that will work are Omega, Emotroid & CMRemix. All others after flashing keep rebooting. That is, system starts, and after 30 secs to 1 minute there is reboot. AND - they don't see the SIM card. Those that work do.
I tried to revert to basics - tried FULL erase from TWRP, reflashed via ODIN original roms (those started no problem), but when in tried again - the same. Other ROMs keep crashing.
So, does anybody have an idea how to totally wipe a phone ( I mean, totally, just leaving ODIN flashing capability so that I can reflash it)? I suspect that there must be somethign somewhere that stayed after one of the ROMs. And what puzzles me, those ROMs that now crash it, were working prevoiusly.
Any ideas/advice will be appreciated.
Thanks!
mjaxa said:
Hi!
Just got myself Note 4, and after rooting and installing TWRP I started looking for ROM that fits my needs. And here goes the strange thing - after tryign few ROMs, now the only ones that will work are Omega, Emotroid & CMRemix. All others after flashing keep rebooting. That is, system starts, and after 30 secs to 1 minute there is reboot. AND - they don't see the SIM card. Those that work do.
I tried to revert to basics - tried FULL erase from TWRP, reflashed via ODIN original roms (those started no problem), but when in tried again - the same. Other ROMs keep crashing.
So, does anybody have an idea how to totally wipe a phone ( I mean, totally, just leaving ODIN flashing capability so that I can reflash it)? I suspect that there must be somethign somewhere that stayed after one of the ROMs. And what puzzles me, those ROMs that now crash it, were working prevoiusly.
Any ideas/advice will be appreciated.
Thanks!
Click to expand...
Click to collapse
flash firmware with pit file and in odin option tick on.( nand erase all ) it will reparation your internal memory and completely wipe your device DONT TICK ON EFS CLEAR IN ODIN. download firmware from link below for your model , extarct file you will have repair firmware along with pit file, choose in odin AP for firmware and PIT for pit file and hit start,after odin pass make sure do a wipe data & data factory reset. hope that helps.
http://www.tsar3000.com/Joomla/inde...ader-csc-pit-files&catid=55:samsung&Itemid=82
For a week my G935A worked fine... direct out of the box I flashed ENG Kernel and Rooted, then installed apps and configured - no issues.
Today it was working then it hung on wake.. I tried to reboot and now it gets stuck at the AT&T logo and vibrates 3 times - over and over
I can get to Odin and Recovery screens easily so I tried to flash the ENG Kernel again & deleting Cache Partition few times - didnt fix it.
Also tried booting into Safe Mode - it never gets there, stays at AT&T logo.
When I go into the Recovery menu, I see at the bottom, in red... "dm-verity verification failed"
Anyone know how I can recover from this without Factory Reset? It took 6 hours to reinstall and config all my apps - really want to avoid that.
thx for the help!
as far as I know there is no way to fix and save your stuff. I had the same problem with G930A and even doing a factory reset would only allow my phone to boot but then I get apps crashing and then a reboot puts you back at ATT logo and the vibrates. Best to ditch the whole engboot and go back to stock until a more stable rooting method comes out.
Some searches shows posts that say using Odin to flash HOME_CSC without having to wipe and everything survive
... Where can I get HOME_CSC? I dl'd stock rom and dont see it in there.
thx!
Same here this morning on my 930A w/ PK1....went to watch a youtube vid and everything google related began crashing.
Only been on engboot for a couple days but did flash the v15 debloat last night. hmmmm.
Any luck with the files or procedure LivinOne?
Update: Flashed the PK1 CSC and got into recovery.
Wiped cache and reboot, same failure mode....sad face.
Flashed CSC again, into recovery, factory reset, wiped cache.
Back to setting my "new" device up.
Dec 30 update: Same crash, SEMI same problem.
I get the single vibration followed by the 3 vibrations after I put my pin in from a restart.
Same symptoms prior, all background activities began crashing.
Running all PK1 files from QRhinehardt post.
Any thoughts?
I ended up wiping and flashing the T-Mobile firmware and using the ENG bootloader (but not rooted yet). It is WAY faster than the AT&T was. I've only had issues with Wifi Calling (it doesnt seem to work most of the time)
s7 at&t
Hi, did you first flash with eng bootloader and then tmobile rom? I miss this step...I appreciate your help please
Single vibration followed by the 3 vibrations
Hi, were you able to fix the problem? I'm also getting the single vibration followed by the 3 vibrations.
Do you know why is this occurring? I performed a wipe cache and factory reset but still nothing.
bweegn said:
Same here this morning on my 930A w/ PK1....went to watch a youtube vid and everything google related began crashing.
Only been on engboot for a couple days but did flash the v15 debloat last night. hmmmm.
Any luck with the files or procedure LivinOne?
Update: Flashed the PK1 CSC and got into recovery.
Wiped cache and reboot, same failure mode....sad face.
Flashed CSC again, into recovery, factory reset, wiped cache.
Back to setting my "new" device up.
Dec 30 update: Same crash, SEMI same problem.
I get the single vibration followed by the 3 vibrations after I put my pin in from a restart.
Same symptoms prior, all background activities began crashing.
Running all PK1 files from QRhinehardt post.
Any thoughts?
Click to expand...
Click to collapse
Thanks in advance for any who can offer help, and I'm sorry if I missed something obvious.
I did a stupid thing and started playing with Odin, attempting to switch from Unlocked firmware on my 950U1 to T-Mobile firmware, in an effort to get RCS support. Before flashing I was running the latest available snapdragon pie beta.
At this point I have flashed all sorts of things in an attempt to restore my device, but I am fairly sure that I flashed a Factory Binary for my device that for some unknown reason would no properly boot and would then crash, rebooting into a kernel panic screen. I decided to abandon my project and flash back to stock and now my S8 will not completely boot. It will go through the Galaxy S8 splash screen, through the animated Samsung screen, then into a Starting Android screen were it will almost immediately freeze the animation and reboot.
I can't remember how exactly I got here but what I thought was that flashing stock firmware via odin succesfully should result in a complete restore. I have always chosen the CSC file as opposed to the HOME_CSC file in order to make sure that data is wiped. I have wiped the cache and data via recovery which resulted in no change.
Any thoughts on how to recover this device? I'm at wit's end with it after several hours of trying everything that google brings up so far as I can figure.
carterra3 said:
Thanks in advance for any who can offer help, and I'm sorry if I missed something obvious.
I did a stupid thing and started playing with Odin, attempting to switch from Unlocked firmware on my 950U1 to T-Mobile firmware, in an effort to get RCS support. Before flashing I was running the latest available snapdragon pie beta.
At this point I have flashed all sorts of things in an attempt to restore my device, but I am fairly sure that I flashed a Factory Binary for my device that for some unknown reason would no properly boot and would then crash, rebooting into a kernel panic screen. I decided to abandon my project and flash back to stock and now my S8 will not completely boot. It will go through the Galaxy S8 splash screen, through the animated Samsung screen, then into a Starting Android screen were it will almost immediately freeze the animation and reboot.
I can't remember how exactly I got here but what I thought was that flashing stock firmware via odin succesfully should result in a complete restore. I have always chosen the CSC file as opposed to the HOME_CSC file in order to make sure that data is wiped. I have wiped the cache and data via recovery which resulted in no change.
Any thoughts on how to recover this device? I'm at wit's end with it after several hours of trying everything that google brings up so far as I can figure.
Click to expand...
Click to collapse
Flash stock firmware with nand erase all
Tried flashing stock firmware with Nand Erase checked, no change.