Has anyone thought about stuffing the touchstone coil into the nexus4? It sounds stupid i know since the n4 already has wireless charging built in, but the chargers are expensive and hard to find while the touchstone chargers are cheap and plentiful.
peachpuff said:
Has anyone thought about stuffing the touchstone coil into the nexus4? It sounds stupid i know since the n4 already has wireless charging built in, but the chargers are expensive and hard to find while the touchstone chargers are cheap and plentiful.
Click to expand...
Click to collapse
The Qi protocol requires that the receiver send a handshake to the transmitter to start charging. If a non-Qi device is on the plate, then it will do a start and stop every 20 sec to poll for the signal. I am working on changing the Touchstone coil to a Qi transmitter coil and see what happens. I received the Qi coil, Qi inductive charging sleeve (for testing) and waiting on a Palm touchstone sleeve. My concern is that the touchstone without the Qi communication on charging status may overheat the N4 if it doesn't stop the power transmission properly.
terracode said:
My concern is that the touchstone without the Qi communication on charging status may overheat the N4 if it doesn't stop the power transmission properly.
Click to expand...
Click to collapse
People have put touchstone coil's in other phones and had no issues, i don't see how it would be any different here. There are 4 contact points that connect the qi coil and nfc on the rear cover, attach the touchstone coil to 2 of them and hope you can close the cover with everything inside.
peachpuff said:
People have put touchstone coil's in other phones and had no issues, i don't see how it would be any different here. There are 4 contact points that connect the qi coil and nfc on the rear cover, attach the touchstone coil to 2 of them and hope you can close the cover with everything inside.
Click to expand...
Click to collapse
He's doing the opposite; he's replacing the coil in the touchstone charger with a QI charging coil.
I connected the Qi compliant coil to the Touchstone board and it didn't recognize the Qi receiver so it didn't start energy transfer. I then moved the thin wire coil that the Touchston uses to sense a Palm Receiver to above the Qi coil. The transmitter didn't start with a Qi receiver, but did recognize the Palm receiver and started energizing the coil. Issue was the voltage was very low due to the mismatched coils (Qi transmitter and TS receiver). I need to take apart the Touchstone receiver to see what it uses to activate the transmitter. More tinkering is needed.
I think QI controls the charging level from the phone, by communicating back to the charger. It may not be a good idea to disable this mechanism by swithing a charge coil on manually (though I'd think that the phone would not charge at all, then).
If you want to try, I think QI uses 141 KHz. Supply that to a coil at the correct power and see if it charges.
jutezak said:
I think QI controls the charging level from the phone, by communicating back to the charger. It may not be a good idea to disable this mechanism by swithing a charge coil on manually (though I'd think that the phone would not charge at all, then).
If you want to try, I think QI uses 141 KHz. Supply that to a coil at the correct power and see if it charges.
Click to expand...
Click to collapse
I am actually doing the opposite. The Qi coil is on the transmit side attached to the touchstone charger power board. I need a way of sending a proper signal to the Palm Touchstone so that it energizes the coil. The Qi receiver doesn't have the proper interface to send a signal to the Touchstone to power up.
$50 is hardly expensive.... Wall Mart wanted $50 for a plug in travel charger for my galaxy tablet. Just find the lg one.
Sent from my Nexus 4 using Tapatalk 2
Qi coil
terracode said:
I am actually doing the opposite. The Qi coil is on the transmit side attached to the touchstone charger power board. I need a way of sending a proper signal to the Palm Touchstone so that it energizes the coil. The Qi receiver doesn't have the proper interface to send a signal to the Touchstone to power up.
Click to expand...
Click to collapse
So are you able to replace the qi coil successfully to TS?
For someone who want's multiple docks around, $50 does add up. For someone like me who has 2 or more touchstone chargers laying around from previous mods/palm phones this would be useful.
I've tried to do the following to my Nexus 4, but couldn't get off the back cover without damaging the phone (I could get everything but one corner of the phone to pop open, I noticed I was beginning to damage the body a bit and stopped trying).
Mind you, the following needs to be used with a case; works best with rugged cases/hard cases.
If anyone is able to open their phone up you can try my following idea:
1. Remove the back of the phone
2..There should be 4 pins, 2 for NFC, and 2 for the QI coil.
3. Use a voltmeter to find out which pin is positive and which is negative.
-- I am not sure if the touchstone coil could fit INSIDE the phone, so I assumed it would not fit, and came up with this solution--
4. Using copper tape (if you've modded your GNEX before, you probably have some left over) stick it onto the pins, and lead them outside of the back cover, wrapping around so you see the copper tape on the OUTSIDE of the phone
5. Close the phone back up, the copper tape should now be hanging outside of the side of the phone.
6. Get your touchstone coil and tape/adhere it to the inside of your selected case.
7. Take your copper tape yet again and solder it to the leads of the touchstone coil, and position the copper tape so it touches the existing tape (from the nexus) when you put the case onto your phone.
That's it. The touchstone should be thin enough so that it doesn't interfere with the fitting of the case. This was the situation for my previous two mods with Galaxy Nexus's, the fit of the case was no problem. (Otterbox Commuter, and SGP Neo-Hybrid).
DDRFAN said:
For someone who want's multiple docks around, $50 does add up. For someone like me who has 2 or more touchstone chargers laying around from previous mods/palm phones this would be useful.
I've tried to do the following to my Nexus 4, but couldn't get off the back cover without damaging the phone (I could get everything but one corner of the phone to pop open, I noticed I was beginning to damage the body a bit and stopped trying).
Mind you, the following needs to be used with a case; works best with rugged cases/hard cases.
If anyone is able to open their phone up you can try my following idea:
1. Remove the back of the phone
2..There should be 4 pins, 2 for NFC, and 2 for the QI coil.
3. Use a voltmeter to find out which pin is positive and which is negative.
-- I am not sure if the touchstone coil could fit INSIDE the phone, so I assumed it would not fit, and came up with this solution--
4. Using copper tape (if you've modded your GNEX before, you probably have some left over) stick it onto the pins, and lead them outside of the back cover, wrapping around so you see the copper tape on the OUTSIDE of the phone
5. Close the phone back up, the copper tape should now be hanging outside of the side of the phone.
6. Get your touchstone coil and tape/adhere it to the inside of your selected case.
7. Take your copper tape yet again and solder it to the leads of the touchstone coil, and position the copper tape so it touches the existing tape (from the nexus) when you put the case onto your phone.
That's it. The touchstone should be thin enough so that it doesn't interfere with the fitting of the case. This was the situation for my previous two mods with Galaxy Nexus's, the fit of the case was no problem. (Otterbox Commuter, and SGP Neo-Hybrid).
Click to expand...
Click to collapse
Was this simply the metal coil or the entire assembly including board from a Pre charging cover? very Interested as I have a Nexus 4 I will be receiving Monday
singularityq said:
Was this simply the metal coil or the entire assembly including board from a Pre charging cover? very Interested as I have a Nexus 4 I will be receiving Monday
Click to expand...
Click to collapse
You should only have to replace the metal coil.
OP, a simple google search would have sufficed http://www.webosnation.com/nexus-4-gains-touchstone-charging-thanks-clever-hacking
Does one of these exist? I have a cheap TPU S-line case from ebay that I bought when the phone was first released. It works with the QI charger but it does not keep the dust out of the ports.
I bought two cheapies off ebay to test if something a little thicker would work with the QI charger and so far nothing does. Seems that any case that covers ports are thick and may not work with the QI charger.
BTW its the Energizer charger, not the official Google one.
Have you considered just getting a microusb port cover? http://www.moddiy.com/products/modDIY-Micro%2dUSB-Protective-Jack-Cover.html for example
ziddey said:
Have you considered just getting a microusb port cover? http://www.moddiy.com/products/modDIY-Micro%2dUSB-Protective-Jack-Cover.html for example
Click to expand...
Click to collapse
I have but if a case exists that will work then I would like to give that a shot first. I notice the covers for the cases are snug fit so it wont allow dust in at all when a plug may leave room between it and the case. I work in a very dirty environment and would like to keep the phone itself as clean as possible.
Hi I bought the wireless charger door for my s5 but now I cannot find a case or cover that fits on this as Is thicker.
If anyone can guide me to the right way.
Thanks
what i use...
i use the nokia 900 charger and "Spigen Slim Armor" as my case.
works fine and the wireless is ok.
Aviadash said:
i use the nokia 900 charger and "Spigen Slim Armor" as my case.
works fine and the wireless is ok.
Click to expand...
Click to collapse
doesnt it fit too tight? I wonder as the battery door is bulky, and i dont want to damage my s5 buttons
Has anyone tried Otterbox Strada with a magnetic car mount?
Can the magnet work through 2 layers of case?
Any recommendations on a car mount for the Otterbox Strada?
A great case.
Shofar1
Not sure, but be careful if you wirelessly charge while having the case. The metal plate for your mount can get very hot while wirelessly charging if it isn't positioned right.
ryanpm40 said:
Not sure, but be careful if you wirelessly charge while having the case. The metal plate for your mount can get very hot while wirelessly charging if it isn't positioned right.
Click to expand...
Click to collapse
Yes I have the Samsung wireless charger and while it works fine the S8+ does get hot.\
The Magnetic car mount I'm thinking of does not charge by itself.
I would use the car charger and a cable.
Thanks