This is a TWRP Backup of the Middle East Marshmallow OTA (B511) for TL 10 International Version:
Link:https://mega.nz/#F!i1QkjLrI
Decription key:!Rj6Iw_--xg8vABPi76NxeQ
Place the file within TWRP>BACKUPS folder in your SD card.
I did a factory reset via TWRP pior to backing-up and did not notice some of the apps (Most Google Apps and some stock Huawei apps like Compass, Mirror, etc.) went missing. So after restoring the back-up, you may restore those missing apps by doing the following:
1.) Download the Stock MM recovery
2.) Boot to fastboot mode then flash the stock recovery.
3.) After rebooting phone boot to stock recovery mode.
4.) On stock recovery choose "Wipe Data/Factory Reset". Once back on the phone will regain all lost apps/icons
Hi! Link mega crashed! ?
Enviado desde mi JAZZ
link not working please check before post
Link works.It must enter the decryption key: !Rj6Iw_--xg8vABPi76NxeQ
Hi is only for TL10?
tried to roll back from Marshmallow B511 but you fail, try my method here
http://forum.xda-developers.com/mate-7/general/tried-to-roll-b511-to-b326-fail-try-t3302479
blitzkriegger said:
This is a TWRP Backup of the Middle East Marshmallow OTA (B511) for TL 10 International Version:
Link:https://mega.nz/#F!i1QkjLrI
Decription key:!Rj6Iw_--xg8vABPi76NxeQ
Place the file within TWRP>BACKUPS folder in your SD card.
I did a factory reset via TWRP pior to backing-up and did not notice some of the apps (Most Google Apps and some stock Huawei apps like Compass, Mirror, etc.) went missing. So after restoring the back-up, you may restore those missing apps by doing the following:
1.) Download the Stock MM recovery
2.) Boot to fastboot mode then flash the stock recovery.
3.) After rebooting phone boot to stock recovery mode.
4.) On stock recovery choose "Wipe Data/Factory Reset". Once back on the phone will regain all lost apps/icons
Click to expand...
Click to collapse
Work very fine TL09
I tried several times on TL10 international version, but when rebooting system always got stucked on huawei logo screen. Even waited long periods with no effect.
Any hint?
pasil.pt said:
I tried several times on TL10 international version, but when rebooting system always got stucked on huawei logo screen. Even waited long periods with no effect.
Any hint?
Click to expand...
Click to collapse
did it work for you, because i tried it and had the same results, if it didn't, would you mind telling me what you did to make your phone work again please
---------- Post added at 02:34 PM ---------- Previous post was at 02:18 PM ----------
pasil.pt said:
I tried several times on TL10 international version, but when rebooting system always got stucked on huawei logo screen. Even waited long periods with no effect.
Any hint?
Click to expand...
Click to collapse
did it work for you, because i tried it and had the same results, if it didn't, would you mind telling me what you did to make your phone work again please
nozeback said:
did it work for you, because i tried it and had the same results, if it didn't, would you mind telling me what you did to make your phone work again please
---------- Post added at 02:34 PM ---------- Previous post was at 02:18 PM ----------
did it work for you, because i tried it and had the same results, if it didn't, would you mind telling me what you did to make your phone work again please
Click to expand...
Click to collapse
I can't remember well but i think I went into recovery (TWRP) to restore a backup
If you cannot go into twrp recovery either to restore a bckp or to flash another rom you need to go into the fastboot procedure, flashing img files from PC. But yoy can see this procedures on other threads
urgently need Stock MM recovery,plz
hi,thanks for the guide,I urgently need Stock MM recovery and I cant Find it,unfortunately my device has no recovery and most unfortunately it was on MM,After boot loader unlock, I flashed another recovery which seems to be incompatible and now device has no recovery,tried more than 10 recovery but none leave me a chance,please upload a stock MM recovery if possible.
Here
https://mega.nz/#!w15xjZxL!0-alMyU4RgsxQ6K6FjOPZna-piQLXODLE0QarKtdVCg
Send from ?
Looking for the stock browser apk from b331. Any chance someone has a link
ogre del said:
Looking for the stock browser apk from b331. Any chance someone has a link
Click to expand...
Click to collapse
Here https://mega.nz/#!Z9gjRJpR!iJmlBWIFRLhhDRIFu3--FoxkAj6Pc6wZCuajDZ7WKZw
Send from ?
New link thanks to @Blue.Ember
https://mega.nz/#!e1BmGBKY!xoGZ2s-AbUyg2khj98e-veul95_KU0esstyK4SmqtiM
Send from ?
Related
DISCLAIMER : You are solely responsible for what you do with this information.
Last Update: Jan.29 (2017)
••••••••••••••••••••••
Custom Recovery
••••••••••••••••••••••
Thanks to @jackeagle for these
TWRP Builds (these ARE compatible)
I used FlashFire to flash the recovery (must be rooted)
See second post for help with Odin.
•••••••••••
Backups
•••••••••••
Notice: THESE ARE TWRP BACKUPS!!
A factory reset will be necessary prior to the restore, or best before it.
Further help in post 2
This debloated (with SuperSU) backup is the latest I have uploaded and it's only around 622mb
A debloated without root version is also abailable.
**by debloated I have removed a bunch of stock Samsung/Google and other applications.
This old 2gb backup has SuperSU and AppOps pre-installed(forgot to remove, has all stock apps)
These other stock partitions include the stock recovery.
I am currently unable (no PC) to produce a flashable zip, if you know what you are doing you can make use of these other files.
This phone needs:
- A permissive kernel
- a deodexed version of this ROM (for xposed)
- cm12/13
- etc etc
If you found this post helpful please hit thank you and leave feedback
Helpful Info:
TWRP NOT RECOGNIZING THE BACKUP???
Stay calm, here's what you do:
zenful said:
∆∆∆make sure to put the files for the these backups in a folder on root of your SD card called TWRP/BACKUPS/<device ID>/BACKUPS/ in order for TWRP to recognize the backups on your device. If you don't know your device ID, just use TWRP and make a backup of whats currently on your device to get the folder with that device ID than place the backup in that location.
Click to expand...
Click to collapse
How to Flash TWRP recovery using Odin said:
Download Odin 3.12.3
Unzip the Odin 3.12.3 .zip file and run/open Odin3 v3.12.3.exe file from the extracted files on your PC.
Make sure you’ve downloaded a Odin flashable TWRP recovery .tar file compatible for your device.
(If applicable) Enable OEM unlock:
Go to Settings » About phone » and tap Build number seven times to enable Developer options.
Go back to main Settings page, scroll to bottom and select Developer options from there.
Under Developer options, look for Enable OEM unlock checkbox/toggle and enable it.
Boot your device into Download mode:
Switch off your device.
Press and hold “Home + Power + Volume down” buttons for a few seconds until you see a warning screen.
Press Volume Up on the warning screen to accept it and boot into Download mode.
Once your device is in download mode, connect it to the PC with a USB cable. The Odin window on PC should detect the device and show an “Added!!” message.
Now click on the AP tab on Odin window and select the TWRP recovery .tar file that you downloaded for your device.
└ Note: DON’T play with any other options on the screen. You’re only required to connect your device and select the TWRP recovery .tar file in the AP tab.
Click the Start button on Odin and wait for it to finish the process. Once it has finished successfully, you’ll see a pass message on the Odin screen.
Your device will automatically reboot when Odin is done flashing. You can then disconnect your device.
How to boot into TWRP recovery on a Samsung Galaxy device
Switch off your device.
Press and hold “Home + Power + Volume Up” buttons for a few seconds and as soon as you see your device’ logo on-screen, release three buttons altogether. Your device will boot into TWRP recovery.
source
source
Click to expand...
Click to collapse
Anybody find out about custom recoveries on the SM-978L?
Well I don't know if this helps, but my brother soft bricked his phone while trying to put a custom boot-animation on his phone. I figured out how to fix it by flashing https://download.chainfire.eu/719/CF-Root/CF-Auto-Root/CF-Auto-Root-e5lte-e5lteub-sme500m.zip using odin 3.09. After i flashed it and reset his device it booted back up like normal, and he had root. Just for ****s and giggles i decided to try to flash http://forum.xda-developers.com/gal...ment/recovery-twrp-samsung-galaxy-e5-t3283089. When i tried to reboot into recovery it told me that the seandroid was enforcing. My question is if we flash http://forum.xda-developers.com/gal...nel-permissive-lollipop-stock-kernel-t3387015 will we be able to use this custom recovery. I know it is not built for this specific device, but i was wondering if they were close enough for it to work. Just to afraid to flash it and brick his device with no backup images available.
bndnrd321 said:
Well I don't know if this helps, but my brother soft bricked his phone while trying to put a custom boot-animation on his phone. I figured out how to fix it by flashing https://download.chainfire.eu/719/CF-Root/CF-Auto-Root/CF-Auto-Root-e5lte-e5lteub-sme500m.zip using odin 3.09. After i flashed it and reset his device it booted back up like normal, and he had root. Just for ****s and giggles i decided to try to flash http://forum.xda-developers.com/gal...ment/recovery-twrp-samsung-galaxy-e5-t3283089. When i tried to reboot into recovery it told me that the seandroid was enforcing. My question is if we flash http://forum.xda-developers.com/gal...nel-permissive-lollipop-stock-kernel-t3387015 will we be able to use this custom recovery. I know it is not built for this specific device, but i was wondering if they were close enough for it to work. Just to afraid to flash it and brick his device with no backup images available.
Click to expand...
Click to collapse
Did you ever gather up enough courage to try? It would seem like it should work. I might try it myself, but I cant afford to buy another one if it fails.
JoeSchmo2840 said:
Did you ever gather up enough courage to try? It would seem like it should work. I might try it myself, but I cant afford to buy another one if it fails.
Click to expand...
Click to collapse
I'm the brother bndnrd was referring to.... at this time we haven't tried it but we are almost sure that this straight talk (tracphone) version is the same as the one mentioned. Just like everyone else though I just don't have $200 to test it if it were to fail.
My stupidity in not setting perms right on the boot animation is what caused the soft brick in the first place and apparently.. what ever he did.... was able to boot the phone back up bypassing perms.
If I can pay off a few bills early enough I will set aside some cash and try the build we think will work but that will be at least a month away.
If TWRP actually works after that permissive kernel is installed, we can finally get a stock nandroid backup. That would take the fear away from testing that custom cyanogen build.
JoeSchmo2840 said:
If TWRP actually works after that permissive kernel is installed, we can finally get a stock nandroid backup. That would take the fear away from testing that custom cyanogen build.
Click to expand...
Click to collapse
I ended up making a nandroid backup of this phone and the only thing I couldn't make a backup of was the boot and recovery for it.
You can find out all the partitions you need to use dd with to start a backup by doing
ls -al /dev/block/bootdevice/by-name
Click to expand...
Click to collapse
If I had the resources for a computer I would have uploaded a copy of my stock image, I'll see what I can do about getting one up. Also saw this tool that I thought may be useful for getting a flashable image.
tool-mmcblk0-extractor
Anyways, until next time x.x
Just wanted to post this and see if anyone has theirs different.
Also if someone could decompile the boot.img (I have a link to mine I can send) I'll work on a passive kernel for us.
допоможіть! потрібна прошивка для мого sm-s978l 4g
Took and wiped the system and data. now loaded only Samsung logo and TWRP 3.0.2
Or maybe someone has a backup of SM-S978L 4G?
oleksandr.lutsyk said:
Took and wiped the system and data. now loaded only Samsung logo and TWRP 3.0.2
Or maybe someone has a backup of SM-S978L 4G?
Click to expand...
Click to collapse
What do you need a backup of? I haven't uploaded data or system partitions yet but I have the rest.
Also, you successfully got TWRP 3.0.2 working? If so please share the details on how please
[via Tapatalk]
Help! Need firmware for my SM-S978L [5.0.2] Straight Talk's E5
Took and wiped the system and data. now loaded only Samsung logo and tvrp
Or maybe someone has a backup of SM-S978L [5.0.2] Straight Talk's E5?
---------- Post added at 10:22 PM ---------- Previous post was at 10:19 PM ----------
I need backup or firmware....
---------- Post added at 10:49 PM ---------- Previous post was at 10:22 PM ----------
zenful said:
What do you need a backup of? I haven't uploaded data or system partitions yet but I have the rest.
Also, you successfully got TWRP 3.0.2 working? If so please share the details on how please
[via Tapatalk]
Click to expand...
Click to collapse
androiding. how/how-to-install-twrp-recovery-using-odin/
If you do this it will be possible. Make a backup for me)
updated main post, will try uploading backup by tonight
zenful backup request
zenful said:
UPDATED dec 8 2016
#############
TWRP thanks to user @jackeagle for providing us with some TWRP builds for the E5.
Jackeagle TWRP build (I believe he has updated versions but this is the one I KNOW works for this phone)
https://www.androidfilehost.com/?fid=24052804347821291
Other builds
http://forum.xda-developers.com/showpost.php?p=62973386&postcount=2
http://androiding.how/galaxy-e5-twrp-recovery/
http://androiding.how/how-to-install-twrp-recovery-using-odin/
####
You can also use FlashFire to flash the recovery as well (must have root first)
Have fun guys!
#edit dec11.2016
Have a twrp backup of the /system partition and a dump of the other partitions as well, just get up with me on here.
Click to expand...
Click to collapse
Hello, I currently have the twrp running but for some reason google play services has stopped working has blocked me our of many of my apps and functions on the phone. The only backup I have at all has this occurring may I please use your backup and partitions so I can have a working phone for the upcoming holiday.
El_Ogan said:
Hello, I currently have the twrp running but for some reason google play services has stopped working has blocked me our of many of my apps and functions on the phone. The only backup I have at all has this occurring may I please use your backup and partitions so I can have a working phone for the upcoming holiday.
Click to expand...
Click to collapse
Hey @El_Ogan check your inbox, or the first post to this thread for the link. Hope it helps, happy holidays
??/
zenful said:
Hey @El_Ogan check your inbox, or the first post to this thread for the link. Hope it helps, happy holidays
Click to expand...
Click to collapse
i have this phone and twrp works but nothing eles is this a complet back up i can just restore from twrp or is there something eles i am in need of to get this phoe working its a sm-s978l but shows e500h when i plug it in to my computer ??? so i am really confused
bullfrog83 said:
i have this phone and twrp works but nothing eles is this a complet back up i can just restore from twrp or is there something eles i am in need of to get this phoe working its a sm-s978l but shows e500h when i plug it in to my computer ??? so i am really confused
Click to expand...
Click to collapse
Hey no worries and yes it's just a full backup from TWRP just stupid in the sdcard and navigate to TWRP's restore section and it should auto find it. Any other files needed I'll also have, but this a bit a flashable zip or flashable via Odin, and
I imagine Odin says that after you flashed TWRP right? If so that's because that's what the TWRP was made for so it seems like Odin checked the recovery.
If it said that BEFORE you flashed it, that's very intriguing and helpful to me
thank you very much i really like this phone maybe ill be able to use it again havent went back to odin since i put twrp on the phone but when i plug into my computer it says e500h in window on my computer when in twrp on the phone used to say sm-s978l so im not sure just the way it is introduced by windows
bullfrog83 said:
i have this phone and twrp works but nothing eles is this a complet back up i can just restore from twrp or is there something eles i am in need of to get this phoe working its a sm-s978l but shows e500h when i plug it in to my computer ??? so i am really confused
Click to expand...
Click to collapse
bullfrog83 said:
thank you very much i really like this phone maybe ill be able to use it again havent went back to odin since i put twrp on the phone but when i plug into my computer it says e500h in window on my computer when in twrp on the phone used to say sm-s978l so im not sure just the way it is introduced by windows
Click to expand...
Click to collapse
I feel ya just let me know if you need any more help and goodluck
So, while trying to follow the steps given to me to gain root access for data recovery, I stupidly swiped allow system modifications on the signed TWRP. The phone has been unable to boot into system ever since and only gets stuck on ZTE screen. I am able to boot into recovery, bootloader, FTM, and EDL but not system. This suggests that the system image has been corrupted somehow. I downloaded the B15 zip from ZTE's support page and tried to do update via SD card from stock recovery.
After selecting the zip file the phone screen showed the following (I tried with and without renaming the zip to update.zip):
supported api: 3
Install /sdcard/<"filename>".zip
finding update package, opening update package, verifying update package
E: footer is wrong
Update package verification took 1.0 s (result 1).
E: signature verification failed
Installation aborted
This entails that perhaps the official zip is faulty in some way. I chatted with ZTE support, he told me to wipe cache, try redownloading the zip file and retry without renaming, But no dice. Then he suggested a factory reset. I had read that for some others a factory reset had fixed the problem, so with some qualms, I went through with it. Lo and behold, even after 30 min the phone was still stuck on ZTE screen. ZTE support no longer has a B29 zip for downgrading and does not offer a B19 zip. So according to the support guy my last option is sending my phone in for repairs where they'll reformat the phone and reflash Stock ROM free of charge.
While that's all well and dandy, I am still desperately attempting data recovery (all efforts have been futile and I am well aware that I will likely be wholly unsuccessful). So, I was wondering if any of you guys had a backup of the fully stock system image, or had a zip file, or solution that would allow me to boot into system successfully without rooting or unlocking bootloader. A fully stock OS is preferred but am open to alternates such as DrakenFX's fastboot enabled EDL zip if there's absolutely no way to go back to fully stock OS. I am ok with downgrading and then updating later. Just don't want to get the phone reformatted. Thanks in advance.
TLDR: Phone stuck on ZTE screen; factory reset did not help; need to flash fully stock system image and maybe can boot successfully into system; if all else fails will probably submit warranty claim.
Install supersu or dm-verity to bypass the security checks.
tupurl said:
So, while trying to follow the steps given to me to gain root access for data recovery, I stupidly swiped allow system modifications on the signed TWRP. The phone has been unable to boot into system ever since and only gets stuck on ZTE screen. I am able to boot into recovery, bootloader, FTM, and EDL but not system. This suggests that the system image has been corrupted somehow. I downloaded the B15 zip from ZTE's support page and tried to do update via SD card from stock recovery.
After selecting the zip file the phone screen showed the following (I tried with and without renaming the zip to update.zip):
supported api: 3
Install /sdcard/<"filename>".zip
finding update package, opening update package, verifying update package
E: footer is wrong
Update package verification took 1.0 s (result 1).
E: signature verification failed
Installation aborted
This entails that perhaps the official zip is faulty in some way. I chatted with ZTE support, he told me to wipe cache, try redownloading the zip file and retry without renaming, But no dice. Then he suggested a factory reset. I had read that for some others a factory reset had fixed the problem, so with some qualms, I went through with it. Lo and behold, even after 30 min the phone was still stuck on ZTE screen. ZTE support no longer has a B29 zip for downgrading and does not offer a B19 zip. So according to the support guy my last option is sending my phone in for repairs where they'll reformat the phone and reflash Stock ROM free of charge.
While that's all well and dandy, I am still desperately attempting data recovery (all efforts have been futile and I am well aware that I will likely be wholly unsuccessful). So, I was wondering if any of you guys had a backup of the fully stock system image, or had a zip file, or solution that would allow me to boot into system successfully without rooting or unlocking bootloader. A fully stock OS is preferred but am open to alternates such as DrakenFX's fastboot enabled EDL zip if there's absolutely no way to go back to fully stock OS. I am ok with downgrading and then updating later. Just don't want to get the phone reformatted. Thanks in advance.
TLDR: Phone stuck on ZTE screen; factory reset did not help; need to flash fully stock system image and maybe can boot successfully into system; if all else fails will probably submit warranty claim.
Click to expand...
Click to collapse
I think this is B29 stock image DrakenFX has uploaded it on sharing website, give it a try.
https://www.androidfilehost.com/?fid=312968873555009511
romeoh said:
I think this is B29 stock image DrakenFX has uploaded it on sharing website, give it a try.
https://www.androidfilehost.com/?fid=312968873555009511
Click to expand...
Click to collapse
Thanks for the link!
Will this work via the update from sd card option on the stock recovery? Or would you recommend flashing from TWRP? Or via MiFlash in EDL mode?
gpz1100 said:
Install supersu or dm-verity to bypass the security checks.
Click to expand...
Click to collapse
Doesn't that require unlocked bootloader? I want to avoid voiding the warranty.
tupurl said:
Thanks for the link!
Will this work via the update from sd card option on the stock recovery? Or would you recommend flashing from TWRP? Or via MiFlash in EDL mode?
Click to expand...
Click to collapse
This is the zte official B29 package and the only way to used it from the stock recovery from the SD card. It won't work with twrp because it requires the stock recovery. You can also use this method and you don't have to have unlcked bootloader http://forum.xda-developers.com/axon-7/development/edl-emergency-dl-mode-twrp-unlock-t3553514/page26
romeoh said:
This is the zte official B29 package and the only way to used it from the stock recovery from the SD card. It won't work with twrp because it requires the stock recovery. You can also use this method and you don't have to have unlcked bootloader http://forum.xda-developers.com/axon-7/development/edl-emergency-dl-mode-twrp-unlock-t3553514/page26
Click to expand...
Click to collapse
So, I just now tried to apply the package you linked to (Draken FX stock Marshmallow) and it gave me the same errors :/
E: footer is wrong and E: signature verification failed. Should I try something else?
Enable OEM unlock and flash zte zip from external SD. Sometimes they zip it twice so check the file.
lafester said:
Enable OEM unlock and flash zte zip from external SD. Sometimes they zip it twice so check the file.
Click to expand...
Click to collapse
I can't boot into system. Is there a way to enable OEM unlock from recovery, EDL, or factory test mode?
Did you check the zip? You could always use miflash b15 full.
lafester said:
Did you check the zip? You could always use miflash b15 full.
Click to expand...
Click to collapse
I've been trying to use MiFlash to flash the B29 stock zip by DrakenFX that the romeroh linked to but I can't see my device in MiFlash :/. I know EDL works cuz the axon7tool is able to detect it and write or read recovery and boot properly. Ideas on how to get MiFlash to detect my phone?
tupurl said:
I've been trying to use MiFlash to flash the B29 stock zip by DrakenFX that the romeroh linked to but I can't see my device in MiFlash :/. I know EDL works cuz the axon7tool is able to detect it and write or read recovery and boot properly. Ideas on how to get MiFlash to detect my phone?
Click to expand...
Click to collapse
axon7tool uses different drivers. install the correct drivers for miflash.
tupurl said:
I've been trying to use MiFlash to flash the B29 stock zip by DrakenFX that the romeroh linked to but I can't see my device in MiFlash :/. I know EDL works cuz the axon7tool is able to detect it and write or read recovery and boot properly. Ideas on how to get MiFlash to detect my phone?
Click to expand...
Click to collapse
Ok, I think there was a little misunderstanding about the B29 link that I sent to you bro. That file can only be flashed in Stock recovery you can't flash it with MiFlash. If you want to use MiFlash the only version that's available to flash in EDL mode is Nougat B15. Just reread the OP of the the link I've sent to you before and If you didn't understand anything let us know there is always someone here will help you.
romeoh said:
Ok, I think there was a little misunderstanding about the B29 link that I sent to you bro. That file can only be flashed in Stock recovery you can't flash it with MiFlash. If you want to use MiFlash the only version that's available to flash in EDL mode is Nougat B15. Just reread the OP of the the link I've sent to you before and If you didn't understand anything let us know there is always someone here will help you.
Click to expand...
Click to collapse
I'm having sort of the same problem except I'm stuck on the bootloader unlocked screen and any rom I flash gets stuck on "patching system image unconditionally"
Fazedyrus said:
I'm having sort of the same problem except I'm stuck on the bootloader unlocked screen and any rom I flash gets stuck on "patching system image unconditionally"
Click to expand...
Click to collapse
Have you tried to use the EDL method?
https://forum.xda-developers.com/axon-7/development/edl-emergency-dl-mode-twrp-unlock-t3553514
It should work on fixing this issue even if you are with Unlocked Bootloader, but you'll end up on Nougat B15 because this is the only full EDL mode package available.
romeoh said:
Have you tried to use the EDL method?
https://forum.xda-developers.com/axon-7/development/edl-emergency-dl-mode-twrp-unlock-t3553514
It should work on fixing this issue even if you are with Unlocked Bootloader, but you'll end up on Nougat B15 because this is the only full EDL mode package available.
Click to expand...
Click to collapse
Did that, the flash is successful but I still have the same problem in that the system won't boot. Should I just relock and rma at this point?
---------- Post added at 09:30 PM ---------- Previous post was at 09:27 PM ----------
romeoh said:
Have you tried to use the EDL method?
https://forum.xda-developers.com/axon-7/development/edl-emergency-dl-mode-twrp-unlock-t3553514
It should work on fixing this issue even if you are with Unlocked Bootloader, but you'll end up on Nougat B15 because this is the only full EDL mode package available.
Click to expand...
Click to collapse
Flashing supersu and dmverity zip doesn't work either
Fazedyrus said:
Did that, the flash is successful but I still have the same problem in that the system won't boot. Should I just relock and rma at this point?
---------- Post added at 09:30 PM ---------- Previous post was at 09:27 PM ----------
Flashing supersu and dmverity zip doesn't work either
Click to expand...
Click to collapse
You doing a full wipe before flashing? Flashing b15 full (no twrp)? Also try format data instead of wipe.
I've gone through this a few times and always manage to get booting.
lafester said:
You doing a full wipe before flashing? Flashing b15 full (no twrp)? Also try format data instead of wipe.
I've gone through this a few times and always manage to get booting.
Click to expand...
Click to collapse
I've done that several times already with no success. I think somehow my device just doesn't work
---------- Post added at 04:14 PM ---------- Previous post was at 04:12 PM ----------
lafester said:
You doing a full wipe before flashing? Flashing b15 full (no twrp)? Also try format data instead of wipe.
I've gone through this a few times and always manage to get booting.
Click to expand...
Click to collapse
also tried flashing DrakenFX's B29 Stock images but still can't boot into system
---------- Post added at 04:21 PM ---------- Previous post was at 04:14 PM ----------
lafester said:
You doing a full wipe before flashing? Flashing b15 full (no twrp)? Also try format data instead of wipe.
I've gone through this a few times and always manage to get booting.
Click to expand...
Click to collapse
I've tried many things over the past 3 days for over 10 hours so I think I'm gonna return this phone and just get a OP3T
---------- Post added at 04:45 PM ---------- Previous post was at 04:21 PM ----------
Fazedyrus said:
I've done that several times already with no success. I think somehow my device just doesn't work
---------- Post added at 04:14 PM ---------- Previous post was at 04:12 PM ----------
also tried flashing DrakenFX's B29 Stock images but still can't boot into system
---------- Post added at 04:21 PM ---------- Previous post was at 04:14 PM ----------
I've tried many things over the past 3 days for over 10 hours so I think I'm gonna return this phone and just get a OP3T
Click to expand...
Click to collapse
also, not being able to flash any rom with a working twrp makes it look like only I have this problem
---------- Post added at 05:32 PM ---------- Previous post was at 04:45 PM ----------
Fazedyrus said:
I've done that several times already with no success. I think somehow my device just doesn't work
---------- Post added at 04:14 PM ---------- Previous post was at 04:12 PM ----------
also tried flashing DrakenFX's B29 Stock images but still can't boot into system
---------- Post added at 04:21 PM ---------- Previous post was at 04:14 PM ----------
I've tried many things over the past 3 days for over 10 hours so I think I'm gonna return this phone and just get a OP3T
---------- Post added at 04:45 PM ---------- Previous post was at 04:21 PM ----------
also, not being able to flash any rom with a working twrp makes it look like only I have this problem
Click to expand...
Click to collapse
yep, everything is stock yet I am still not able to boot into system
lafester said:
Enable OEM unlock and flash zte zip from external SD. Sometimes they zip it twice so check the file.
Click to expand...
Click to collapse
tupurl said:
So, while trying to follow the steps given to me to gain root access for data recovery, I stupidly swiped allow system modifications on the signed TWRP. The phone has been unable to boot into system ever since and only gets stuck on ZTE screen. I am able to boot into recovery, bootloader, FTM, and EDL but not system. This suggests that the system image has been corrupted somehow. I downloaded the B15 zip from ZTE's support page and tried to do update via SD card from stock recovery.
After selecting the zip file the phone screen showed the following (I tried with and without renaming the zip to update.zip):
supported api: 3
Install /sdcard/<"filename>".zip
finding update package, opening update package, verifying update package
E: footer is wrong
Update package verification took 1.0 s (result 1).
E: signature verification failed
Installation aborted
This entails that perhaps the official zip is faulty in some way. I chatted with ZTE support, he told me to wipe cache, try redownloading the zip file and retry without renaming, But no dice. Then he suggested a factory reset. I had read that for some others a factory reset had fixed the problem, so with some qualms, I went through with it. Lo and behold, even after 30 min the phone was still stuck on ZTE screen. ZTE support no longer has a B29 zip for downgrading and does not offer a B19 zip. So according to the support guy my last option is sending my phone in for repairs where they'll reformat the phone and reflash Stock ROM free of charge.
While that's all well and dandy, I am still desperately attempting data recovery (all efforts have been futile and I am well aware that I will likely be wholly unsuccessful). So, I was wondering if any of you guys had a backup of the fully stock system image, or had a zip file, or solution that would allow me to boot into system successfully without rooting or unlocking bootloader. A fully stock OS is preferred but am open to alternates such as DrakenFX's fastboot enabled EDL zip if there's absolutely no way to go back to fully stock OS. I am ok with downgrading and then updating later. Just don't want to get the phone reformatted. Thanks in advance.
TLDR: Phone stuck on ZTE screen; factory reset did not help; need to flash fully stock system image and maybe can boot successfully into system; if all else fails will probably submit warranty claim.
Click to expand...
Click to collapse
lafester is correct, the B15 file from downloaded from ZTE is zipped twice. There is an actual update.zip inside a folder inside the "America A2017U SD card software package(A2017UV1.1.0B15)SD_W" zip. When I bricked my phone, I extracted the update.zip and I was able to flash it from the SD with the stock recovery. Hope that helps.
Howie Dub said:
lafester is correct, the B15 file from downloaded from ZTE is zipped twice. There is an actual update.zip inside a folder inside the "America A2017U SD card software package(A2017UV1.1.0B15)SD_W" zip. When I bricked my phone, I extracted the update.zip and I was able to flash it from the SD with the stock recovery. Hope that helps.
Click to expand...
Click to collapse
where can I find this zip
Good Morning everybody,
so yesterday was a rough day and when it eventually end i recive the october security update on the phone, without thinking i installed it and the phone does not boot up , instead i face my recovery (TWRP 3.1.1-0).
Of course i've made a mess because i was on stock rooted 7.0 on my retEU XT1572 phone with unlocked bootloader and status 3
i've tryed to restore a previous nandroid backup wihtout success, so today i downloaded the new RESURRECTION REMIX v5.8.4 (4 december wich is based on stock android 7) but i have no luck even with that...
Do i miss something?is there any rom to try with now? or i have to make a downgrade of my firmware to make it work again?
thanks in advice!
UPDATE:
phone boot now but always in recovery and after rebooting in bootloader i can reboot system from there.. it seems that if you download an update and the install process doesen't go in place every time you restart the device it always try to re-flash it, that's why i'm always in recovery.. i foun a similar post with this solution but i think it need some changes before it will work on our device (but i don't have the knowledge to set it right :S )
LAST UPDATE:
boot fixed by using this command in twrp recovery
dd if=/dev/zero of=/dev/block/platform/f9824900.sdhci/by-name/misc
misc file running at the startup redirecting the boot in the recovery, put blank in the file let the system boot up normally
You missed very much.
Here is stock RetEu, before october update:
https://forum.xda-developers.com/moto-x-style/general/stock-xt-1572-reteu-7-0-ddumped-files-t3712521
Wipe all with twrp and flash all. After it you can get OTA's.
---------- Post added at 10:59 AM ---------- Previous post was at 10:57 AM ----------
Here is RR 5.8.5 working on N modem:
https://forum.xda-developers.com/mo...ial-resurrection-remix-v5-8-3-t3637204/page40 post #397
Wipe all with twrp, update twrp to 3.2 and you can flash it right now.
@
---------- Post added at 11:03 AM ---------- Previous post was at 10:59 AM ----------
@Husky34
oh thanx man! i've already seen that post but i wasn't sure that it can work for me. i have some question befor starting:
1) i need the new twrp 3.2 to flash resurrection-remix? because as i mention before i've already tried to flash it with twrp 3.1 and it doesen't work (the rom is the same that you linked page40 post #397 )
2) do i have to flash stock-xt-1572-reteu-7-0-ddumped-files before point 1)?
dzidexx said:
You missed very much.
Here is stock RetEu, before october update:
https://forum.xda-developers.com/moto-x-style/general/stock-xt-1572-reteu-7-0-ddumped-files-t3712521
Wipe all with twrp and flash all. After it you can get OTA's.
---------- Post added at 10:59 AM ---------- Previous post was at 10:57 AM ----------
Here is RR 5.8.5 working on N modem:
https://forum.xda-developers.com/mo...ial-resurrection-remix-v5-8-3-t3637204/page40 post #397
Wipe all with twrp, update twrp to 3.2 and you can flash it right now.
@
---------- Post added at 11:03 AM ---------- Previous post was at 10:59 AM ----------
@Husky34
Click to expand...
Click to collapse
Husky34 said:
oh thanx man! i've already seen that post but i wasn't sure that it can work for me. i have some question befor starting:
1) i need the new twrp 3.2 to flash resurrection-remix? because as i mention before i've already tried to flash it with twrp 3.1 and it doesen't work
2) do i have to flash stock-xt-1572-reteu-7-0-ddumped-files before point 1)?
Click to expand...
Click to collapse
1. I think so. 3.2.x will be needed for future builds.
1a. You flashed RR for MM modem.
2. No, but this is only way to get ota update.
"swearing in italian" it was a twrp bug.. after a backup restore if you hit restart the phone restart in recovery, you need to boot into bootloader and reboot system from there -.-
thanks to all of you guys!!
strange fact, now if i turn off the phone and again on i'm still on recovery, i have to reboot bootloader and system from there.
i think something is pointing at the recovery instead system..
edit: it seems that if you download an update and the install process doesen't go in place every time you restart the device it always try to re-flash it, that's why i'm always in recovery.. i foun a similar post with this solution but i think it need some changes before it will work on our device (but i don't have the knowledge to set it right :S )
Ota update didn't end.
I think you can try clear data & cache otaupdate app and disable it. Link2sd can help with it. @Husky34
dzidexx said:
Ota update didn't end.
I think you can try clear data & cache otaupdate app and disable it. Link2sd can help with it. @Husky34
Click to expand...
Click to collapse
just tried but wihout luck.. maybe i can wait someone make the flashable update but i don't think this fix the issue
Flash uploaded stock.
dzidexx said:
Flash uploaded stock.
Click to expand...
Click to collapse
actually i fixed the issue using this command
dd if=/dev/zero of=/dev/block/platform/f9824900.sdhci/by-name/misc
misc file running at the startup redirecting the boot in the recovery, put blank in the file let the system boot up normally
Husky34 said:
actually i fixed the issue using this command
dd if=/dev/zero of=/dev/block/platform/f9824900.sdhci/by-name/misc
misc file running at the startup redirecting the boot in the recovery, put blank in the file let the system boot up normally
Click to expand...
Click to collapse
thanks, this command just saved me. but misc file in my XT1575 is under
/dev/block/platform/0/f9824900.sdhci/by-name/misc
but now I can't check system update in the OS anymore, I think flash back factory recovery mine help. Do you know where to download stock 7.0 recovery for 1575?
Edit: found it for 1575 here.
pshadoww said:
thanks, this command just saved me. but misc file in my XT1575 is under
/dev/block/platform/0/f9824900.sdhci/by-name/misc
but now I can't check system update in the OS anymore, I think flash back factory recovery mine help. Do you know where to download stock 7.0 recovery for 1575?
Edit: found it for 1575 here.
Click to expand...
Click to collapse
you can also use link2sd to disable the update app so it doesn't bother you,
or wait untill someone create a zip of the update and flash it into recovery.
thanks, that worked for me as well.
File was located at /dev/block/platform/soc.0/f9824900.sdhci/by-name/misc
FIRSTLY BACKUP BACKUP BACKUP any important data.
Please feel free to share this thread!!
I HARD-BRICKED my honor 8 twice by installing firmware of other regions(us,uk) but being just a noobie I was able to recover my phone. So don't worry take a chill pill:angel::angel:!!
Requirements:
1. Since you are in a custom rom so developer mode will be ON(if not just click build number 9-10 times) , click USB debugging ON.
2. ROOT not necessary but you can do by many apps or by the method of OEM unlocking(command line - Windows Powershell/Command Prompt)
3. Now download these 2 zip files-
http://update.hicloud.com:8180/TDS/data/files/p3/s15/G1190/g79/v90977/f1/full/update.zip
http://update.hicloud.com:8180/TDS/...el_in/update_data_full_FRD-L02_channel_in.zip
4. Copy these zip files to an SD card
5. Now flashing twrp on your phone-
a) download adb files->Press SHIFT and right click-> Windows POWERSHELL-> write adb devices-> see the o/p as number devices
->enter adb reboot bootloader->See the screen of honor 8-> enter fastboot flash recovery twrp.img(download twrp file and rename it as twrp)
->Now plug off from PC-> Format phone-> Install external sd-> flash the zip file-> GO to recovery.
b) e-recovery will come wipe the options(cache,system)
c)REBOOT
You can now enjoy NOUGAT 7.0 with JIO working properly, you are back to home!!!
Thank you.
Wanna appreciate/help through any mode PM me, it will mean a lot to me.
Which build no. is the above ROM? B350?
What do you mean by format phone ? Factory reset from twrp or delete data?
Oem unlocked message will disappear??
Why there is no huawei apps NFC nor working
Bluetooth not working
Karthiknaik said:
Why there is no huawei apps NFC nor working
Bluetooth not working
Click to expand...
Click to collapse
flash the data file again via dload and if not working then flash the saem via TWRP. it will work 100%
---------- Post added at 11:34 AM ---------- Previous post was at 11:33 AM ----------
pradeesa said:
Oem unlocked message will disappear??
Click to expand...
Click to collapse
Yes. Once you dload and back to stock with locked bootlaoder, that message will disappear.
boris dmello said:
What do you mean by format phone ? Factory reset from twrp or delete data?
Click to expand...
Click to collapse
should be factory reset in TWRP. or you can simply use dlaod to go back.
Cannot update the phone normally
It was flashed successfully , but when I update to the latest version ,during update installation it says failed and to go to e recovery . How can I normally update my phone?
fails
when try to install with TWRP it fails to mount system partition & obviously it fails. Don't know what wrong i'm doing!
Thank you so much! It helped be a lot
Hi guys. This is my first post on XDA.
Now I've got C9 Pro, and hours ago I just got it flashed with the latest Android 8.0.0 ROM, version: C9000ZHU1CRG9.
Also I managed to flash TWRP. Then I started doing the Root things with TWRP, as I had done on Android 7.1.1.
However, I did get issue while doing the Root on Android 8.0 --
Actually the SuperSU was flashed successfully, but after this, the phone kept restarting, failing to enter the OS.
I am definitely sure I did the Root with the right steps.
Also I tried different versions of SuperSU, still the issue existed.
Then I flashed Magisk instead, no use.
I even used other versions of TWRP, still no use!
......
Finally, I quitted, flashing the former Android 7.1.1 ROM.
I can't use a phone without Root, but I really want to experience Android 8.0.0.
Can someone offer me any solution?
Thanks a lot in advance!
there is a new twrp for oreo try it . it may fix your problem
---------- Post added at 12:58 AM ---------- Previous post was at 12:56 AM ----------
Thanks to @travis82
Try this
https://forum.xda-developers.com/showpost.php?p=77344461&postcount=131
aboyazan78 said:
there is a new twrp for oreo try it . it may fix your problem
---------- Post added at 12:58 AM ---------- Previous post was at 12:56 AM ----------
Thanks to @travis82
Try this
https://forum.xda-developers.com/showpost.php?p=77344461&postcount=131
Click to expand...
Click to collapse
I already tried the TWRP you introduced, no use, the issue still exists.
try the latest 3.2.3 and tell if it worked
I suggest to flash a clean oreo via odin then flash the latest twrp from @travis82 then do format data and wipe cache and data from twrp recovery
then install the latest magisk
hope u the best @jasonc417
keep updated
hatib237 said:
try the latest 3.2.3 and tell if it worked
Click to expand...
Click to collapse
You know what, I already tried TWRP 3.2.3, but failed!:crying:
I have tried almost every combination ended up getting bootloop always except when I tried these;
1. Install stock firmware and csc (not home csc this will fully wipe the phone)
2. After finishing it enters to recovery and updates the system. Keep hold of pressing the volume down+home key to enter to download mode as soon as it finishes installing system update.
3. install twrp from here https://www.androidfilehost.com/?fid=1322778262903985796 (original thread https://forum.xda-developers.com/c9-pro/development/twrp-c9ltechn-t3646970 sometimes links can be dead. In that case you can find new link from that thread).
4. Keep holding of pressing Volume Up+Home key while installing twrp to boot into recovery as soon as the phone reboots.
5. While in recovery flash this SuperSU https://forum.xda-developers.com/attachment.php?attachmentid=4164510&d=1496008012 (Located in this thread https://forum.xda-developers.com/attachment.php?attachmentid=4164510&d=1496008012 as "*** Xperia users, and others experiencing bootloops ***
Please use this version instead: "
Your phone should boot normally to setup screen.
After You finish setup you should see supersu icon and your phone should be rooted.
I haven't tested but if your phone is in working condition right now you can try from step 3 to not lose your data.
Good Luck -
Thanks for your method. I think I made it finally!
[email protected] said:
I have tried almost every combination ended up getting bootloop always except when I tried these;
1. Install stock firmware and csc (not home csc this will fully wipe the phone)
2. After finishing it enters to recovery and updates the system. Keep hold of pressing the volume down+home key to enter to download mode as soon as it finishes installing system update.
3. install twrp from here https://www.androidfilehost.com/?fid=1322778262903985796 (original thread https://forum.xda-developers.com/c9-pro/development/twrp-c9ltechn-t3646970 sometimes links can be dead. In that case you can find new link from that thread).
4. Keep holding of pressing Volume Up+Home key while installing twrp to boot into recovery as soon as the phone reboots.
5. While in recovery flash this SuperSU https://forum.xda-developers.com/attachment.php?attachmentid=4164510&d=1496008012 (Located in this thread https://forum.xda-developers.com/attachment.php?attachmentid=4164510&d=1496008012 as "*** Xperia users, and others experiencing bootloops ***
Please use this version instead: "
Your phone should boot normally to setup screen.
After You finish setup you should see supersu icon and your phone should be rooted.
I haven't tested but if your phone is in working condition right now you can try from step 3 to not lose your data.
Good Luck -
Click to expand...
Click to collapse
There is, however, one problem with the given TWRP:
Before flashing SuperSU, I did format, or exactly, mount /data.
But when the phone was rebooted again, /data resumed unmounted, resulting in failure in flashing other ZIPs (It said "unable to mount /system").
Then I got the phone rebooted, the terrible bootloop occurred again!
That is to say, we have to flash all ZIPs in one time after mounting /data without rebooting the phone, but sometimes this is not possible.
Now my phone has gone back again to Android 7.1.1, and I think I have to wait for an official TWRP that supports Android 8.0 thoroughly on C9 Pro!
[email protected] said:
I have tried almost every combination ended up getting bootloop always except when I tried these;
1. Install stock firmware and csc (not home csc this will fully wipe the phone)
2. After finishing it enters to recovery and updates the system. Keep hold of pressing the volume down+home key to enter to download mode as soon as it finishes installing system update.
3. install twrp from here https://www.androidfilehost.com/?fid=1322778262903985796 (original thread https://forum.xda-developers.com/c9-pro/development/twrp-c9ltechn-t3646970 sometimes links can be dead. In that case you can find new link from that thread).
4. Keep holding of pressing Volume Up+Home key while installing twrp to boot into recovery as soon as the phone reboots.
5. While in recovery flash this SuperSU https://forum.xda-developers.com/attachment.php?attachmentid=4164510&d=1496008012 (Located in this thread https://forum.xda-developers.com/attachment.php?attachmentid=4164510&d=1496008012 as "*** Xperia users, and others experiencing bootloops ***
Please use this version instead: "
Your phone should boot normally to setup screen.
After You finish setup you should see supersu icon and your phone should be rooted.
I haven't tested but if your phone is in working condition right now you can try from step 3 to not lose your data.
Good Luck -
Click to expand...
Click to collapse
[email protected] said:
I have tried almost every combination ended up getting bootloop always except when I tried these;
1. Install stock firmware and csc (not home csc this will fully wipe the phone)
2. After finishing it enters to recovery and updates the system. Keep hold of pressing the volume down+home key to enter to download mode as soon as it finishes installing system update.
3. install twrp from here https://www.androidfilehost.com/?fid=1322778262903985796 (original thread https://forum.xda-developers.com/c9-pro/development/twrp-c9ltechn-t3646970 sometimes links can be dead. In that case you can find new link from that thread).
4. Keep holding of pressing Volume Up+Home key while installing twrp to boot into recovery as soon as the phone reboots.
5. While in recovery flash this SuperSU https://forum.xda-developers.com/attachment.php?attachmentid=4164510&d=1496008012 (Located in this thread https://forum.xda-developers.com/attachment.php?attachmentid=4164510&d=1496008012 as "*** Xperia users, and others experiencing bootloops ***
Please use this version instead: "
Your phone should boot normally to setup screen.
After You finish setup you should see supersu icon and your phone should be rooted.
I haven't tested but if your phone is in working condition right now you can try from step 3 to not lose your data.
Good Luck -
Click to expand...
Click to collapse
I tried your guide & used Magisk v17.2 instead of SuperSU at step 5 & successfully resolved the bootloop problem, but I did encounter the problem of data not mounting even after flashing ashyx_dm-verity zip:
jasonc417 said:
There is, however, one problem with the given TWRP:
Before flashing SuperSU, I did format, or exactly, mount /data.
But when the phone was rebooted again, /data resumed unmounted, resulting in failure in flashing other ZIPs (It said "unable to mount /system").
Then I got the phone rebooted, the terrible bootloop occurred again!
That is to say, we have to flash all ZIPs in one time after mounting /data without rebooting the phone, but sometimes this is not possible.
Now my phone has gone back again to Android 7.1.1, and I think I have to wait for an official TWRP that supports Android 8.0 thoroughly on C9 Pro!
Click to expand...
Click to collapse
If anybody has a solution for this problem I'd be glad to here it
Follow those steps
shokolatha said:
I tried your guide & used Magisk v17.2 instead of SuperSU at step 5 & successfully resolved the bootloop problem, but I did encounter the problem of data not mounting even after flashing ashyx_dm-verity zip:
If anybody has a solution for this problem I'd be glad to here it
Click to expand...
Click to collapse
2 days ago I flashed again the Android 8.0 ROM into my C9 Pro with Root successfully, through which I found the actual problem:
The given TWRP only supports the specific SuperSU zip, and while I flash other zip files, the bootloop occurs again. That's why I surrender flashing Xposed zip.
AL_IRAQI said:
Follow those steps
Click to expand...
Click to collapse
Well done
I can confirm that I have enabled mounting data partition in TWRP after using your mentioned Disable_Dm-Verity_ForceEncrypt_09.02.2018 zip file, Although I haven't followed your steps exactly
I have mentioned my steps in earlier reply.
Thanks
AL_IRAQI said:
Follow those steps
Click to expand...
Click to collapse
Thanks first.
Well, I do have a question: can I flash other zip files, like Xposed, with your given TWRP without phone bootloop?
Thanks!
New thread with root guide on oreo (8.0) step by step with required files would be appreciable.
AL_IRAQI said:
Follow those steps
Click to expand...
Click to collapse
Last night I tried this again following the steps, and finally the flash of Xposed and other 3rd-party zip were successfully!
Only one problem: an app named "Toggle Data" could not be run properly.
Again, thanks a lot!
How to do, C9 Pro with Root successfully?
jasonc417 said:
2 days ago I flashed again the Android 8.0 ROM into my C9 Pro with Root successfully, through which I found the actual problem:
The given TWRP only supports the specific SuperSU zip, and while I flash other zip files, the bootloop occurs again. That's why I surrender flashing Xposed zip.
Click to expand...
Click to collapse
Can you explain, how to root C9 Pro with Androis 8.0 ROM.
Thanks a lot.
Murat
[email protected] said:
Can you explain, how to root C9 Pro with Androis 8.0 ROM.
Thanks a lot.
Murat
Click to expand...
Click to collapse
You need to download and install travis's twrp after that format data , flash magisk 17.2 , flash dm verity and reboot
SM-C9000 cihazımdan Tapatalk kullanılarak gönderildi
YusufGKT said:
You need to download and install travis's twrp after that format data , flash magisk 17.2 , flash dm verity and reboot
SM-C9000 cihazımdan Tapatalk kullanılarak gönderildi
Click to expand...
Click to collapse
Hmmm, I don't want to format data. If find another way, better.
Thanks a lot,
Murat
[email protected] said:
Hmmm, I don't want to format data. If find another way, better.
Thanks a lot,
Murat
Click to expand...
Click to collapse
Twrp doesnt support samsung encryption so ypu need to flash dm verity and that needs format data
SM-C9000 cihazımdan Tapatalk kullanılarak gönderildi