I'm rooted but no idea how to disable proximity sensor - G2 Q&A, Help & Troubleshooting

I tried installing the xposed framework but that threw a little notice saying it wasnt going to work. I looked for apps ont he app store but that didnt work as well..
Any ideas on how to disable the proximity sensor so when I turn the screen on it doesnt turn right back off?
Any help is greatly appreciated.

the issue might be your proximity sensor's alignment. it might not have aligned properly. there is a small black rubber holder to hold the proximity sensor. may be you might be missing it or might have loosen it. you can easily fix/align it, if you can open the back cover.
you can install a custom rom to overcome this sudden screen off issue. but when you taking a call your screen will be turning off until other user disconnect the call..
I suggest you fix/align the proximity sensor..
P.S:
There is a small troubleshooting step you can do to see whether your proximity sensor has a slight alignment issue. get a torch or good direct light source and point it directly at proximity sensor. if you can turn your screen on while pointing that light towards proximity sensor, you should have a very small alignment issue. there are plenty of proximity sensor test apps on play store too.

appsmarsterx said:
the issue might be your proximity sensor's alignment. it might not have aligned properly. there is a small black rubber holder to hold the proximity sensor. may be you might be missing it or might have loosen it. you can easily fix/align it, if you can open the back cover.
you can install a custom rom to overcome this sudden screen off issue. but when you taking a call your screen will be turning off until other user disconnect the call..
I suggest you fix/align the proximity sensor..
P.S:
There is a small troubleshooting step you can do to see whether your proximity sensor has a slight alignment issue. get a torch or good direct light source and point it directly at proximity sensor. if you can turn your screen on while pointing that light towards proximity sensor, you should have a very small alignment issue. there are plenty of proximity sensor test apps on play store too.
Click to expand...
Click to collapse
Interseting... My screen broke so I had it replaced and its been having an issue ever since. Also, I don't use it for calls. It is just sitting on a mount in my car most of the day running a few car apps. But it is in airplane mode basically all day lol.

Pr3dict said:
Interseting... My screen broke so I had it replaced and its been having an issue ever since. Also, I don't use it for calls. It is just sitting on a mount in my car most of the day running a few car apps. But it is in airplane mode basically all day lol.
Click to expand...
Click to collapse
that makes sense.. you also replced front housing too right? that's where that rubber proximity sensor holder attached.. if you replace original front housing with aftermarket housing that rubber holder probably won't come with it. most of the repair technicians don't know this.. if you still have the old front housing you should be able to recover it and attach to your new housing..
p. s:
or you should be able to buy it.
here it is
http://rounded.com/lg-g2-d802-rubber-proximity-sensor-module-mbl65540401.html#/product/21920 (also try ebay or aliexpress )

appsmarsterx said:
that makes sense.. you also replced front housing too right? that's where that rubber proximity sensor holder attached.. if you replace original front housing with aftermarket housing that rubber holder probably won't come with it. most of the repair technicians don't know this.. if you still have the old front housing you should be able to recover it and attach to your new housing..
p. s:
or you should be able to buy it.
here it is (also try ebay or aliexpress )
Click to expand...
Click to collapse
Honestly, if its possible I'd rather just disable it completely. I'd rather not open the phone up again if I don't have to and I will never use it for calls anyway.

Pr3dict said:
Honestly, if its possible I'd rather just disable it completely. I'd rather not open the phone up again if I don't have to and I will never use it for calls anyway.
Click to expand...
Click to collapse
if you're not using your g2 for calls, I'd recommend flashing a custom aosp rom. so you wouldn't get in to this sudden screen off issue while unlocking it..

appsmarsterx said:
if you're not using your g2 for calls, I'd recommend flashing a custom aosp rom. so you wouldn't get in to this sudden screen off issue while unlocking it..
Click to expand...
Click to collapse
That sounds exciting.. Lets do it!!!!!!!!!!!!

Related

Proximity sensor while talking on the phone

i tried to search the forum with no results btw
have two cases while receiving/calling with hd2
1. via bluetooth headset - even when the phone is in the pocket some apps starts randomly, even call is disconnected - isn't proximity should cause phone scrren to be blank all time?
2. via the phone - sometimes while talking screen is still dark and pressing eg. home key puts display on. sometimes moving phone away from ear turns screen on.
do you have some or its something with my phone?
I have the same problem, the proximity sensor does not work, I think it works only outside when you have strong light, try it and let me know.
make a call the screen will go off now move it from your face loking up at the sun outside you will see that the screen will turn on.
it works only when I makes a call. when I am getting a call it atays on.
kochav
kochavy said:
I have the same problem, the proximity sensor does not work, I think it works only outside when you have strong light, try it and let me know.
make a call the screen will go off now move it from your face loking up at the sun outside you will see that the screen will turn on.
it works only when I makes a call. when I am getting a call it atays on.
kochav
Click to expand...
Click to collapse
Well you would be wrong then.
It's a proximity sensor, not a light sensor. I just made a call in my darkened room and the proximity sensor functioned flawlessly.
thake the screen protector out or cut it and the proximity sensor will work perfect.
kochavy
kochavy said:
thake the screen protector out or cut it and the proximity sensor will work perfect.
kochavy
Click to expand...
Click to collapse
Wow who would've thought that covering up a sensor designed to sense when objects are close to it would impede its functionality.
Your revelation hepled me fix the microphone on my phone. It wasn't working, and then I realized I had my hand over it!
Yes I have had issues even with the original HTC screen protector which has two small holes directly over the sensors. I finally had to remove it.
Cutting the protector I have not been very successful so far. This creates sharp edges and the protector tends to peel off from that point. For the time being I am relying on the fact that the screen on the HD2 is scratch resistant enough that with normal care it would not get scratched. With over 2 months of use without a protector my screen is still scratchless.
IF it is anything to do with the screen protector, then there are plenty out there that don't have this effect.
I've got a protector on my HD2 and have had it there since just after I got it, so just over 2 months now. The screen protector has worked perfectly, even, kochavy, in the dark, because it detects proximity not light.
I suggest removing any screen protectors and seeing if you still have the problem. If you do, send the phone back as faulty. If you don't, get a better screen protector.
johncmolyneux said:
IF it is anything to do with the screen protector, then there are plenty out there that don't have this effect.
I've got a protector on my HD2 and have had it there since just after I got it, so just over 2 months now. The screen protector has worked perfectly, even, kochavy, in the dark, because it detects proximity not light.
I suggest removing any screen protectors and seeing if you still have the problem. If you do, send the phone back as faulty. If you don't, get a better screen protector.
Click to expand...
Click to collapse
do you have the original HTC screen protector with the two holes? there are some protector that does not cover the top of the phone and leave the two sensors out from protection.
kochavy said:
do you have the original HTC screen protector with the two holes? there are some protector that does not cover the top of the phone and leave the two sensors out from protection.
Click to expand...
Click to collapse
No I don't. The one that came with it never please me much, so I bought some better ones.
The protectors I have don't have any holes for the sensors at the top, but like I said, it just works perfectly. There's a lot more to this issue that just the screen protector, as some people have reported that it works perfectly when they ring certain number, but not when they ring others. From what I've read on other threads, this is commonplace for people who are having this problem, so it's obviously not an issue with their screen protectors. It sounds like a software issue to me, but since it can't be identified as such, they should just return their phones as faulty and hope the replacement doesn't have the same issue.
It would be interesting to know if the people with the described issue have upgraded the ROM to 1.66, as this seems to have fixed a whole slew of issues.
Sensor works by reflecting infrared light. There is small IR lamp with IR detector nearby. You can check that by looking at the sensor through some digital camera or camcorder, whose are usually sensitive to this light. Don't forget the phone must be in call, otherwise the sensor is turned off.
I think the sensor itself is OK. But there seems to be some relationship with guess what .. G-sensor ! Once I found the screen just won't go off during call, and it was when I was lying during the call, and I was holding the phone upside down portrait style.
But as I turned the phone to normal position (normal portrait) and back, it started to work with no problem.
I only had problem with proximity sensor once since then .. but rotating the phone up and down helped again.
I think this needs more investigation .. if you encounter the problem try this.

[Q] Proximity Sensor / Autorotation Not working after Screen Replacement

So I dropped my nexus 4 cracking the screen which required me to replace the LCD assembly. After putting it back together and firing it up I noticed that the Auto Rotation (Yes the setting is checked in the settings) and the proximity sensor are not working. I installed Android sensor box and it is getting no reading from the proximity sensor or the gyro sensor. I have taken the phone apart multiple times to ensure everything is connect and everything looks correct. I have also unlocked the phone and have re flashed the stock rom with it not fixing the problem. Any help would be much appreciated.
My wife destroyed her display. Did same but gyro works fine but proxy is the problem. Work around so far is to set power button to end calls becasue screen just goes black when making/receiving calls kind of makes phone useless if you can't see screen.
I too have taken it apart several times and still nothing. Next plan is to find a new sensor unit and replace it.
From what I have been able to see in all my searching the proxy is extremely sensitive any deviation in placement, smuge on unit or display, minor deviation on color of display, screen protector, any interference from skins can affect it so check all those also.
In one of the threads on the Galaxy Nexus there is a patch to turn off sensor and there is mention of app in market that does the same, haven't tried yet have to get phone from wife to try, could be possible solutions also.
Will post back with findings as I get to try them.
Found great app in market Sensor Kinetic Pro shuts off proximity sensor or any other sensor no more problem with black screen after making calls. Still going to try replacing sensor however found it on Amazon less then $5.00.
silvagroup said:
My wife destroyed her display. Did same but gyro works fine but proxy is the problem. Work around so far is to set power button to end calls becasue screen just goes black when making/receiving calls kind of makes phone useless if you can't see screen.
I too have taken it apart several times and still nothing. Next plan is to find a new sensor unit and replace it.
From what I have been able to see in all my searching the proxy is extremely sensitive any deviation in placement, smuge on unit or display, minor deviation on color of display, screen protector, any interference from skins can affect it so check all those also.
In one of the threads on the Galaxy Nexus there is a patch to turn off sensor and there is mention of app in market that does the same, haven't tried yet have to get phone from wife to try, could be possible solutions also.
Will post back with findings as I get to try them.
Found great app in market Sensor Kinetic Pro shuts off proximity sensor or any other sensor no more problem with black screen after making calls. Still going to try replacing sensor however found it on Amazon less then $5.00.
Click to expand...
Click to collapse
Somewhat comforted to see others are also having the same problem... I recently replaced my nexus 4 screen only to have my proximity sensor fail on me too. Interestingly enough, i disassembled my phone multiple times to test if the sensor still works, turns out it does, but it is super sensitive. In my first experiment I had the sensor dangling out of the socket to see if it was still receptive to light, it worked perfectly - I used my hand as a 'face-simulator' to test for sensitivity. I then tried to place it back in the rubber grommet with the grommet seated firmly in the socket and what I found was that it worked, so long as there was only limited pressure on the enclosure. For example, it only works when there are no adjacent screws (for the plastic motherboard cover) applying pressure in the nearby area. I thought I could live with that, but then I tried putting the rear plastic cover back on and,... back to square one, dead screen on-call. I figure it has something to do with either pressure sensitivity or perhaps the pressure from the screws or the rear cover pushes the sensor too close to the glass?
Anyway I'd be keen to see if replacing the audio jack will actually fix the problem, any of you guys had any success with that? Meanwhile i'm going to just use the power button for ending calls. Any tips for how to use the speakerphone during a call?
Cheers fellas.
New sensor arrived yesterday changed out my wife's non functioning sensor and new one working great. Old sensor was bad !!!! She had dropped the phone several times and last accident she unintentionally threw it. Suggest no one do that
Sent from my Amazon Kindle Fire HD using xda premium
silvagroup said:
New sensor arrived yesterday changed out my wife's non functioning sensor and new one working great. Old sensor was bad !!!! She had dropped the phone several times and last accident she unintentionally threw it. Suggest no one do that
Sent from my Amazon Kindle Fire HD using xda premium
Click to expand...
Click to collapse
New sensor arrived the other day, I have since swapped out the old one, everything works great now!
17
dhaub said:
New sensor arrived the other day, I have since swapped out the old one, everything works great now!
Click to expand...
Click to collapse
whered u get the sensor?
chamilun said:
whered u get the sensor?
Click to expand...
Click to collapse
I know this is old but I'm having the same issue. How did you guys make out? Were did you get the sensor? Saw one on ebay $109 seems pricey
btack said:
I know this is old but I'm having the same issue. How did you guys make out? Were did you get the sensor? Saw one on ebay $109 seems pricey
Click to expand...
Click to collapse
I put a case on mine and it started working. It always would work if i put a bit of pressure on different parts of the phone. So im not sure if bad contact on sensor or if more some type of alignment issue. But it does work now. speakerphone is terrible since cracked screen tho..

[HW] Fixing a proximity sensor

I found this topic about the design flaw:
http://forum.xda-developers.com/showthread.php?t=2129140&highlight=proximity
I've seen it myself, when I was reassembling my phone. Hardware design for that particular part is absolutely HORRIBLE.
It happened after changing the motherboard on my phone. In-call screen turns off immediately and doesn't turn on until the call ends.
Proximity sensor seems to work OK when it is out of its place on the phone, but after placing it back, the path is blocked somehow.
I got a spare part to interchange, but it behaves the exact same way the previous did.
There is a rubber gasket, it fits nicely and holds sensors in place, but it might block the sensor. Without the rubber gasket, sensors are not fixed in place and they work inconsistently.
I am curious, if it is a special way it is assembled, or I am a dumb ass can't figure out how to place it properly.
Please help, otherwise it would be great to know, if there is a way to turn it off in software. Thanks.
bump
Tasker can turn off your proximity sensor while on call.. I think some custom roms also have that feature..
Would be great.
u can use proximity disabler
i lost the rubber thing when i changed the screen!!
i followed these two methods
i used proximity disabler from xposed framework to stop the proximity sensor
you can get that from
http://repo.xposed.info/module/com.mrchandler.disableprox
or follow this tutorial
or
i fixed that using a small cardboard an made two holes exactly infront of the sensor
and that fixed my proximity sensor for my nexus 4 and even made a video for the same you can check that at

[Q] How to disable Proximity sensor in Nexus 4

So i recently upgraded to Lollipop but my proximity sensor is broken. I used an app called Proximity Screen off lite but it is not working on latest android lollipop. So now when i make a call my screen goes dark until the call is disconnected from other party. same is the case with incoming call. Please help
I was in the same situation as you last weekend. Unfortunately, there's no way to get around it in software that I know of. I even went as far as developing an app from scratch to duplicate Proximity Screen Off Lite's functionality, but ended up hitting a road block on the OS level. Another option that would've worked pre-5.0 was to use an xposed mod to disable the proximity sensor, but of course that doesn't work in 5.0 now. Hopefully someone else can chime in with a software solution that I couldn't figure out.
Did you replace your phone's screen by any chance?
Shimakaze said:
I was in the same situation as you last weekend. Unfortunately, there's no way to get around it in software that I know of. I even went as far as developing an app from scratch to duplicate Proximity Screen Off Lite's functionality, but ended up hitting a road block on the OS level. Another option that would've worked pre-5.0 was to use an xposed mod to disable the proximity sensor, but of course that doesn't work in 5.0 now. Hopefully someone else can chime in with a software solution that I couldn't figure out.
Did you replace your phone's screen by any chance?
Click to expand...
Click to collapse
Yes i did :/ nownfed up and hating it. there has to be someway which disable the hardware :/
sink1991 said:
Yes i did :/ nownfed up and hating it. there has to be someway which disable the hardware :/
Click to expand...
Click to collapse
I replaced the original screen with an after-market one as well, and that's what caused my proximity sensor issue. There is a good chance your proximity sensor is actually working perfectly, but the after-market screen is blocking it from reading a "far" value. If you're comfortable with taking your phone apart, you could fix it without replacing anything. There were two things that I did to fix mine, but I'm not sure which of the two actually did the trick. 1) I repositioned the sensor so that it sits further away from the glass, and 2) I scratched off the black paint on the back side of the glass around the two clear sensor holes. Obviously you should attempt option 1 first, because the second option is permanent and will damage the aesthetics of your phone. Others have reported success with option 1, by gluing a thin spacer with two holes to the front of the sensor, but I did not have any luck with it when I tried initially. You will find that it helps a lot to do this while the phone is on, and you can see the results of your changes immediately with the Proximity Sensor Finder app.
Edit: Before you attempt any of the fixes, you should verify that your sensor is in fact working by pointing it away from the phone after opening up the back.
I had the same problem, I gave up on a software fix and I ended up taking the phone apart and fixing it outright. It's not too difficult, all you need is a plastic tool to open the case and a T5 and a 00 screwdriver.
There's a good youtube video (I can't link - see /watch?v=AZDAIgwbXk4) showing how to do it. Skip the battery section, you can keep that in place. At 9:00 he indicates where the proximity sensor and light sensor are. Take the small rubber gasket that covers the two sensors, and flip it around so that the larger hole is over the proximity sensor. Put it back together and turn it on, it should work perfectly.
Also, in the interim, you may wish to have your phone end calls with the power button, it can be found under accessibility settings. At least that way you won't be stuck waiting for the other party to pick up or hang up.
Admiral Nelson said:
I had the same problem, I gave up on a software fix and I ended up taking the phone apart and fixing it outright. It's not too difficult, all you need is a plastic tool to open the case and a T5 and a 00 screwdriver.
There's a good youtube video (I can't link - see /watch?v=AZDAIgwbXk4) showing how to do it. Skip the battery section, you can keep that in place. At 9:00 he indicates where the proximity sensor and light sensor are. Take the small rubber gasket that covers the two sensors, and flip it around so that the larger hole is over the proximity sensor. Put it back together and turn it on, it should work perfectly.
Click to expand...
Click to collapse
I did the same thing. It's a common issue, and that's the typical fix.
Planterz said:
I did the same thing. It's a common issue, and that's the typical fix.
Click to expand...
Click to collapse
I had the same problem, solved by a thin plastic sheat that I drilled two holes in and then cut to the right size.
I placed the plastic part in the bottom of the hole, where to fit the sensor. I also shaved of aboute 1 mm on the part that presses the sensor from the back.
( I hade already taken the blackish film away in a own attempt to fix the problem, at least the light sensor seems to meassure more accurat)
Hi all, I've similar problem on my LG G2 D802. I have tempered glass with covered prox. On KK everything was OK, but unfortunately Lollipop has much more intensivity on prox
and I had the same issue as you, I mean - turned screen while I maked call and vice versa. Moreover, I can't get in to the service menu on LP (AOSP 5.1.1).
I bought new tempered glass with uncovered prox but fortunately Xposed has working old module: Disable proximity sensor.
I don't know about what module you guys talked about but this module works very well.

Possibly broken Proximity Sensor? Screen always goes off when calling

Hey guys,
just yesterday I got my phone back from repair (I cracked my screen, nothing was working then).
Here is a photo of my old screen, which had a hole right below the upper loud speaker:
I think it might be that the drop broke the sensor, and not the repair itself?!?
Using an app like this: https://play.google.com/store/apps/details?id=com.tigermonster.proxfinder shows that my sensor is constantly detecting something.
I'm not using any screen protectors or anything
For now I rooted my device and disabled the sensor by installing the xposed framework and then using http://repo.xposed.info/module/com.mrchandler.disableprox
Strangely enough, yesterday, like 3h after I got my phone back I called someone and everything, including the sensor was working perfectly!
Can anyone show me a picture of such a proximity sensor? Do you guys think a fix like in this video shown: https://www.youtube.com/watch?v=HPHsianYnqo, putting a piece of paper behind the proximity sensor could work?
You never ended up showing any images of the phone before/after the repair but if you have a screen protector fitted to the screen and it doesn't have a little cutout on the right just below the top speaker then the protector is constantly tripping the proximity sensor.
Thanks for your answer. Like I said, I am not using any screen protectors.
Here's an image of my old screen:
http://imgur.com/ufNSseD
I don't think it has anything to do with that damage now tbh, because it was working well yesterday. I guess maybe the connector loosened itself?
Which one here in the pictures to step 6 is the proximity sensor? https://de.ifixit.com/Teardown/Nexus+6P+Teardown/51660
CryNickSystems said:
Thanks for your answer. Like I said, I am not using any screen protectors.
Here's an image of my old screen:
I don't think it has anything to do with that damage now tbh, because it was working well yesterday. I guess maybe the connector loosened itself?
Which one here in the pictures to step 6 is the proximity sensor? [/QUOTE]
It's directly above the t...i3be.cloudfront.net/igi/eDldW3bJmHSbQEYF.huge
Click to expand...
Click to collapse
Thanks for the info about the position of the sensor - I'll definitely do that when I'm going to disassemble my phone (which is gonna take a while since I'm waiting to receive a new rear housing from a seller in the US).
I'm planning to disassemble as little as possible, so I'm hoping it's easy to access the proximity sensor (but guessing by the pictures it should be).
CryNickSystems said:
Thanks for the info about the position of the sensor - I'll definitely do that when I'm going to disassemble my phone (which is gonna take a while since I'm waiting to receive a new rear housing from a seller in the US).
I'm planning to disassemble as little as possible, so I'm hoping it's easy to access the proximity sensor (but guessing by the pictures it should be).
Click to expand...
Click to collapse
Good luck. Hope you can fix it by cleaning it. Make sure to have some thermal compound on hand to replace the old stuff when you disassemble.
Hey one more quick question:
Do you think it's possible to remove the motherboard without removing the battery?
I guess that the problem is that the proximity sensor is either too close to the screen, or too far away (like there's some small gap between the proximity sensor and the screen). I will probably have to remove the motherboard if it's the former (if it's the latter I can just put something like a pice of paper at the back of the rubber).
CryNickSystems said:
Hey one more quick question:
Do you think it's possible to remove the motherboard without removing the battery?
I guess that the problem is that the proximity sensor is either too close to the screen, or too far away (like there's some small gap between the proximity sensor and the screen). I will probably have to remove the motherboard if it's the former (if it's the latter I can just put something like a pice of paper at the back of the rubber).
Click to expand...
Click to collapse
You won't need to remove the battery to remove the main board. You'll just have to unplug it.
Alright, thanks. I am wondering about another thing: Why are there two holes for the light and proximity sensor on the backside of the phone? I was planning to try and first stick some piece of paper on top of that rubber plastic to get the sensor closer to the screen. Why the holes?
Ty.
CryNickSystems said:
Alright, thanks. I am wondering about another thing: Why are there two holes for the light and proximity sensor on the backside of the phone? I was planning to try and first stick some piece of paper on top of that rubber plastic to get the sensor closer to the screen. Why the holes?
Ty.
Click to expand...
Click to collapse
I don't know which type of proximity sensor this is, IR, led, electromagnetic etc. But all proximity sensors I know of have two "eyes" One eye emits ir, led, or electromagnetic field, the other eye looks for a change in the return field. I think you'll find a scratched, smashed return eye. Or debris lodged in the sensor housing. Use a magnifying glass and excellent lighting.
If you shine a bright flashlight at the sensor through the screen can you see anything blocking the eyes? Doesn't matter I guess, you'd have to disassemble to get it out of the way anyways.
---------- Post added at 09:43 PM ---------- Previous post was at 09:16 PM ----------
CryNickSystems said:
Alright, thanks. I am wondering about another thing: Why are there two holes for the light and proximity sensor on the backside of the phone? I was planning to try and first stick some piece of paper on top of that rubber plastic to get the sensor closer to the screen. Why the holes?
Ty.
Click to expand...
Click to collapse
It looks like the prox sensor comes covered in a rubber cover. In this pic the rubber is there:
https://d3nevzfk7ii3be.cloudfront.net/igi/SQfQ23vhRFsvbJJT.huge
In this pic they removed the rubber to expose the prox sensor:
https://d3nevzfk7ii3be.cloudfront.net/igi/eDldW3bJmHSbQEYF.huge
I suspect the rubber could be missing, lost during repair. Or perhaps installed wrong.
hawkswind1 said:
If you shine a bright flashlight at the sensor through the screen can you see anything blocking the eyes? Doesn't matter I guess, you'd have to disassemble to get it out of the way anyways.
Click to expand...
Click to collapse
I did what you asked: There is no light coming out on the back of the phone if that's what you meant.
Anyway, I'll have to wait until I receive my replacement back housing and then I'll try my best to repair the sensor. I hope the rubber is just misaligned.
Alright - so I did have time today to disassemble my phone (got the replacement housing last week).
I noticed that there was no rubber part on top of the light and proximity sensor, as well as on the device above the two (i don't know what that is).
What I did is that I had a small tube like this one: https://sc01.alicdn.com/kf/HTB1hBgwKVXXXXcvXpXXq6xXFXXXY/8mm-small-clear-plastic-PC-pipe-TUBE.jpg which I painted black and put it on top of the approximity sensor.
Everything is working well again (there were some lints on the display right below where the proximity sensor is located, that's probably why it stopped working from one day to another).
I guess the main function of the rubber is to protect the sensor against dust and lints.
I also am very mad at myself for having forgotten to take out the NFC antenna from the old housing before replacing it, so I had to open my phone again after I did already close it (and now there are slight traces of an opening - again )
But apart from that everything's fine now and I hope it'll stay this way.
CryNickSystems said:
Alright - so I did have time today to disassemble my phone (got the replacement housing last week).
I noticed that there was no rubber part on top of the light and proximity sensor, as well as on the device above the two (i don't know what that is).
What I did is that I had a small tube like this one: which I painted black and put it on top of the approximity sensor.
Everything is working well again (there were some lints on the display right below where the proximity sensor is located, that's probably why it stopped working from one day to another).
I guess the main function of the rubber is to protect the sensor against dust and lints.
I also am very mad at myself for having forgotten to take out the NFC antenna from the old housing before replacing it, so I had to open my phone again after I did already close it (and now there are slight traces of an opening - again )
But apart from that everything's fine now and I hope it'll stay this way.
Click to expand...
Click to collapse
Glad you got it fixed! And yeah, unfortunately it's nearly impossible to remove the back cover without leaving dings at the injection site. When I put on my new top and bottom rear covers I removed most of the glue. So next time I can remove them without much trouble.
I am having similar problems. I just traded for a nexus 6P and everything works great except for the proximity sensor. The 6p was just OTAed to 7.0 and I only unlocked it and installed TWRP. No other changes and no root (yet).
There is no screen protector on the device.
When I make a call, the screen stays on. The screen turns off as soon as I cover the proximity sensor. The screen then does not come back on until the call is completed. I downloaded a bunch of proximity apps, including Proximity Sensor Finder. Proximity Sensor Finder (and others) report that sensor detects Far (5cm or more) and Near (value of 0 cm when the sensor is covered). The sensor doesn't seem to identify intermiate values. The odd thing is that the sensor doesn't seem to reset. If I cover the sensor (value of 0 cm) and remove my hand, the sensor continues to read 0 cm.
Does this sound like a hardware or software issue? The device appears to detect both the near and far states, but doesn't return to far after the sensor is uncovered. Thanks for any help.
Solved the problem. I downgraded to MM and the proximity sensor problem persisted, so I figured it was a hardware issue.
I took apart the 6P and the there were signs that repair had been performed. The screen was probably replaced previously. The little rubber gasket covering the proximity sensor was missing, just as the OP described. I cut a blue-colored straw and placed it over the proximity/light sensor. Works perfect!
I need to bump this thread cause a few days ago I started having the same problem that nickfuzz describes.
Now I've got my opened phone in front of me and tried putting a pice of a black straw around the two sensors, but that does not help. It reports 5.0 cm and if I cover the sensor it stays at 0.0 cm
Can anyone give me an advice about what to do now?
Update:
The light sensor is also not working properly: It is reporting way too less lightness, and tends to report 0 lux when I'm not directly holding the phone under a lamp (for instance).
After 5 hours of trying I somehow managed to at least get the sensor to always report 5.0 cm. That's better than constantly reporting 0.0 cm.
I put a piece of a wide straw (there are different sizes, you know) around the hole board on which the two sensors (light & proximity) sit on. I guess this is a bad idea.
I am now trying to get this rubber gasket from somewhere, but I guess I'll have bad luck since I'd have to buy a defective nexus 6p from which I could take it from
UPDATE:
Can anyone tell me why the screen is painted black on the inside, right where the proximity sensor is located? I scraped off the paint and painted it over with a black pen. That must be the reason why the proximity sensor is always reporting 5.0 cm (which doesn't make much sense, because at some point it would have to detect something if it's not broken).
nickfuzz said:
Solved the problem. I downgraded to MM and the proximity sensor problem persisted, so I figured it was a hardware issue.
I took apart the 6P and the there were signs that repair had been performed. The screen was probably replaced previously. The little rubber gasket covering the proximity sensor was missing, just as the OP described. I cut a blue-colored straw and placed it over the proximity/light sensor. Works perfect!
Click to expand...
Click to collapse
Can you tell me if you put the straw around both sensors and their "chassis" (that black thing they sit on), or did you put the straw only around the sensors (i.e. on top of the chassis)?
I still need to find a way to fix my sensors
I tried to use some electric tape and put it on top of the sensors with two small circles cut in, but eventually I figured that the problem actually lies in the black paint on the inside of the screen.
I removed that paint a few weeks ago and I couldn't paint a new black paint on it that is not too thick, so I am stuck with a sensor consequently reporting 5cm.
I did try to use an Edding.
I had the same issue with the proximity sensory and a new 6P, but fixed it with this: https://play.google.com/store/apps/details?id=com.mobiledirection.proximitysensorreset&hl=en
Everything was still good after uninstalling that app too.

Categories

Resources