-help- SM-N910f with SM-N910p bootloader - Galaxy Note 4 Q&A, Help & Troubleshooting

Hello every one
I have bought a Note 4 " SM-N910f " from ebay and when I tried to root it ,I have found that the version of the bootloader belong to another Note 4 (910p).
about device
Model Num: SM-N910F
Android Ver: 5.1.1
Baseband V: N910FXXU1COH4
Build Num: DONGCHAO.A929
CpuZ
model : Samsung Galaxy Note 4 (SM-N910F)
Bootloader :N910PVPU4COG5
Kernel Ver: 3.10.40-5303209(N910PVPU4COG5)
Build Num: DONGCHAO.A929
Odin mode
product name : SM-N910P
current binary: samsung officiel
system status : officiel
reactivation lock off
Knox warranty void : 0x0
the ticket on the back also show the same thing as ''About device''
but when I cheket my IMEI in ""imei.info"" it tell me that my phone is a galaxy s6 edge !!!!
the same IMEI in both (back ticket & software (#*06#))
so what should I do?
because I can't root neither flash a new firmware
Can I relace the bootloader by the one of N910f ?
(I have only try to flash the firmware of N910f ,I did not try n910p firmware's because I am afraid if I succeed I'll finish with locked network phone)
thanks a lot

have same problem. did you succeed to resolve the issue?

I realised that someone has been changing "Sprint Note 4" to look like the international version.
so I decide to install the latest stock rom ( downloaded from sammobile)
Now I am so glad because I didn't get any problem.
I don't Know how but a Note 4(n910c) IMEI was restored not an IMEI of n910p according to "Imei.info"
Hotspot and Network unlocked including LTE

Hi, I am having the same problem as you.
Can you please give me the rom that you used? And which odin version did you use?
thanks.

what version is the modem? when the moden is from n910p too then its a n910p spoofed as n910f. that can be done by changing backcover and mount a sim reader and it works like n910f. so you have a n910p mainboard in it with changed imei with jtag box

niraj2020 said:
Hi, I am having the same problem as you.
Can you please give me the rom that you used? And which odin version did you use?
thanks.
Click to expand...
Click to collapse
Do this only if your bootloader is a N910P**** (Use CPU-Z to check it, you can download it from the market)
You must have a least 60%
You should remove your SIM card
I've used the latest rom from this link.
http://www.sammobile.com/firmwares/download/60440/N910PVPU4COJ6_N910PSPT4COJ6_SPR/
I assume that you've already installed Samsung driver
and that you have the latest version of odin v3.10.7 and that you're familiar on how to use it
but before you proceed you have to :
1- Instal a custom recovery (Twrp)
http://forum.xda-developers.com/not...nt/tool-utility-twrp-2-8-1-0-teamwin-t2915591
2- boot into TWRP
3-in advanced wipe dalvik cache
4-wipe data/factory reset
5-Format /cache
6-Format /system
7-Format /Data
8-go to advanced and reboot to download mode
9-flash the downloaded rom
wait (10-15min) until your device come to world
Now you have a fresh and clean note 4
10-check your IMEI (*#06#) in http://www.imei.info/
11-restrict data and wifi usage for the following app
Sprint ID
Mobile Installer
Sprint Zone
MyScript Resource Manager
12-Update Your System (settings > System Update > Update Now)
Because this is not the latest build You should upgrade to N910PVPS4COK1 (150mo)
to correct some issue with Google Play Store and other things
13- Update you Play Store and Google Services thru the Store
14- shutdown your device when finished
15-insert your SIM and wake up your Note 4
16-you should root it to profit
(remove unwanted sprint apps it's recommended check the forum to find them out -Use Titanium Backup pro #1 )
enjoy and wait for the Marshmallow =)

geiti94 said:
what version is the modem? when the moden is from n910p too then its a n910p spoofed as n910f. that can be done by changing backcover and mount a sim reader and it works like n910f. so you have a n910p mainboard in it with changed imei with jtag box
Click to expand...
Click to collapse
Hi.
So how to I get the phone to work? It is in a bootloop when switched on and I cannot go into recovery mode since the phone restarts itself when I try to do so. However I have access to download mode.
Also how do I check the version of the modem?
---------- Post added at 03:50 PM ---------- Previous post was at 03:48 PM ----------
cam_bob22 said:
Do this only if your bootloader is a N910P**** (Use CPU-Z to check it, you can download it from the market)
You must have a least 60%
You should remove your SIM card
I've used the latest rom from this link.
http://www.sammobile.com/firmwares/download/60440/N910PVPU4COJ6_N910PSPT4COJ6_SPR/
I assume that you've already installed Samsung driver
and that you have the latest version of odin v3.10.7 and that you're familiar on how to use it
but before you proceed you have to :
1- Instal a custom recovery (Twrp)
http://forum.xda-developers.com/not...nt/tool-utility-twrp-2-8-1-0-teamwin-t2915591
2- boot into TWRP
3-in advanced wipe dalvik cache
4-wipe data/factory reset
5-Format /cache
6-Format /system
7-Format /Data
8-go to advanced and reboot to download mode
9-flash the downloaded rom
wait (10-15min) until your device come to world
Now you have a fresh and clean note 4
10-check your IMEI (*#06#) in http://www.imei.info/
11-restrict data and wifi usage for the following app
Sprint ID
Mobile Installer
Sprint Zone
MyScript Resource Manager
12-Update Your System (settings > System Update > Update Now)
Because this is not the latest build You should upgrade to N910PVPS4COK1 (150mo)
to correct some issue with Google Play Store and other things
13- Update you Play Store and Google Services thru the Store
14- shutdown your device when finished
15-insert your SIM and wake up your Note 4
16-you should root it to profit
(remove unwanted sprint apps it's recommended check the forum to find them out -Use Titanium Backup pro #1 )
enjoy and wait for the Marshmallow =)
Click to expand...
Click to collapse
hello, how do I make sure if my bootloader is a N910P? I cannot download CPU-Z on the phone since the phone is in a bootloop and not switching on.
Before I had the problem, it was written SM-N910F in the about device of the phone. In download mode, it is written N910p and at the back of the phone it is written Sm-N915F.

If you can access the download mode, you simply flash the custom recovery and follow the instructions

you can get it working by flashing n910p rom with odin (download it from sammobile) after that i can say you how to get it again full working with a n910f rom so that you dont have anymore any sprint apps on it

cam_bob22 said:
If you can access the download mode, you simply flash the custom recovery and follow the instructions
Click to expand...
Click to collapse
I have followed all the instructions but the phone still keeps on rebooting.

geiti94 said:
you can get it working by flashing n910p rom with odin (download it from sammobile) after that i can say you how to get it again full working with a n910f rom so that you dont have anymore any sprint apps on it
Click to expand...
Click to collapse
I am interested on how to do it ...
I was looking for this method, but I find nothing...
thanks

geiti94 said:
you can get it working by flashing n910p rom with odin (download it from sammobile) after that i can say you how to get it again full working with a n910f rom so that you dont have anymore any sprint apps on it
Click to expand...
Click to collapse
please give me how to change from 910P to 910F , i want a international note 4 rom

cam_bob22 said:
I am interested on how to do it ...
I was looking for this method, but I find nothing...
thanks
Click to expand...
Click to collapse
yassine78 said:
please give me how to change from 910P to 910F , i want a international note 4 rom
Click to expand...
Click to collapse
after flashing sprint odin rom install twrp recovery fot it. after that download any rom for n910f and flash it with twrp and then flash a kernel for n910p and it will boot without sprint apks. so you have now n910f rom an no more sprint things

geiti94 said:
after flashing sprint odin rom install twrp recovery fot it. after that download any rom for n910f and flash it with twrp and then flash a kernel for n910p and it will boot without sprint apks. so you have now n910f rom an no more sprint things
Click to expand...
Click to collapse
thank you for your fast reply, i'll try it
it's possible with official firmwars to change from 910p to 910f ???

geiti94 said:
after flashing sprint odin rom install twrp recovery fot it. after that download any rom for n910f and flash it with twrp and then flash a kernel for n910p and it will boot without sprint apks. so you have now n910f rom an no more sprint things
Click to expand...
Click to collapse
thanks for your reply but
Is it possible to flash an *.Md5 file with TWRP ??
If not ,will you give us more details

no solution for official firmwares???

After flashing TWRP, Can we just install a custom n910p rom?

linkerMed said:
After flashing TWRP, Can we just install a custom n910p rom?
Click to expand...
Click to collapse
yes

cam_bob22 said:
yes
Click to expand...
Click to collapse
Thank you! I'll try it out soon.

I just flashed my n910p with a custom rom and it works so much better now, plus its pre-rooted. Thanks again

Related

Flashing questions

I actually wanted to flash the leaked Lollipop for my new Note 3 but from what I can read it's not safe just yet... i'm not rooted and can't backup my PIT. Also I read a whole lot about wifi-bugs and so on.
But coming from S5 I really want a fresh look on my Note 3 so I thought I'd flash a custom ROM.
If I understand everything correct I have to do the following:
1: Flash custom recovery with ODIN
2: Flash custom ROM from recovery
I don't need to be rooted before I flash a custom recovery with ODIN, right?
I don't care about triggering Knox. I'll just flash the Stock Lollipop when it's available.
Have I got the procedure right?
Manneman32 said:
I actually wanted to flash the leaked Lollipop for my new Note 3 but from what I can read it's not safe just yet... i'm not rooted and can't backup my PIT. Also I read a whole lot about wifi-bugs and so on.
But coming from S5 I really want a fresh look on my Note 3 so I thought I'd flash a custom ROM.
If I understand everything correct I have to do the following:
1: Flash custom recovery with ODIN
2: Flash custom ROM from recovery
I don't need to be rooted before I flash a custom recovery with ODIN, right?
I don't care about triggering Knox. I'll just flash the Stock Lollipop when it's available.
Have I got the procedure right?
Click to expand...
Click to collapse
Yes you are right.
Regarding to backing up the PIT file, it is not necessary to backup the PIT file from your device. You can get a PIT file from the similar device, i.e the device with the same model name and same CSC. You can use Phone INFO ★Samsung★ app to get your Model Name and CSC.
vndnguyen said:
Yes you are right.
Regarding to backing up the PIT file, it is not necessary to backup the PIT file from your device. You can get a PIT file from the similar device, i.e the device with the same model name and same CSC. You can use Phone INFO ★Samsung★ app to get your Model Name and CSC.
Click to expand...
Click to collapse
Allright, thanx!
Where do I find a PIT that matches my model?
Manneman32 said:
Allright, thanx!
Where do I find a PIT that matches my model?
Click to expand...
Click to collapse
First obtain your Model Name and CSC as I have said. Then search on Google, e.g. PIT file N9005 XME, where N9005 is Model Name, XME is CSC.
Ok! I think I´ll stick with 4.4.2 until the official Lollipop comes. Even if I succeed flashing Lollipop I don´t want to risk WiFi-problems and other bugs since I´m not rooted
May I ask where I can find Custom Recovery for Note 3 SM-N9005 32gb 4.4.2 XXUGNI4?
Best regards!
Manneman32 said:
Ok! I think I´ll stick with 4.4.2 until the official Lollipop comes. Even if I succeed flashing Lollipop I don´t want to risk WiFi-problems and other bugs since I´m not rooted
May I ask where I can find Custom Recovery for Note 3 SM-N9005 32gb 4.4.2 XXUGNI4?
Best regards!
Click to expand...
Click to collapse
You can search for CWM or TWRP recovery...
To download correct recovery for your device, you will need Device Type and Product Name (e.g. hlte/hltexx or something like that). You can find it using the above mentioned Phone INFO ★Samsung★ app.
vndnguyen said:
You can search for CWM or TWRP recovery...
To download correct recovery for your device, you will need Device Type and Product Name (e.g. hlte/hltexx or something like that). You can find it using the above mentioned Phone INFO ★Samsung★ app.
Click to expand...
Click to collapse
Well I have begun searching but I can´t really find anything...
Device Type: hlte
Product Name: htlexx
Edit: Is it this one? http://teamw.in/project/twrp2/202
Manneman32 said:
Well I have begun searching but I can´t really find anything...
Device Type: hlte
Product Name: htlexx
Edit: Is it this one? http://teamw.in/project/twrp2/202
Click to expand...
Click to collapse
Here you go:
- TWRP Recovery: http://teamw.in/project/twrp2/202
- CWM Recovery: https://www.clockworkmod.com/rommanager
Sweet! I got it right!
So... ODIN to flash custom recovery and the just flash a pre-rooted ROM and I´m all set?
Thanx a million for the help! The "ThankYou-Button" has been clicked!
I must have done something wrong... Or am I missing something?
I used Odin 3.09 and started it as administrator. Everything connected fine and I selected the .tar-file (the correct one) and the procedure went ok, green across the board! The phone rebooted and still all OK. Shut of the phone and after 30 sec I booted to recovery but the stock one was still there...
Any ideas?
Edit: I found this... Do I dare to use it?
http://forum.xda-developers.com/showpost.php?p=56660810&postcount=31
Manneman32 said:
I must have done something wrong... Or am I missing something?
I used Odin 3.09 and started it as administrator. Everything connected fine and I selected the .tar-file (the correct one) and the procedure went ok, green across the board! The phone rebooted and still all OK. Shut of the phone and after 30 sec I booted to recovery but the stock one was still there...
Any ideas?
Edit: I found this... Do I dare to use it?
http://forum.xda-developers.com/showpost.php?p=56660810&postcount=31
Click to expand...
Click to collapse
Sorry I have no idea as I'm currently on the stock recovery after upgrading to 4.4.2.
Try to google search for the solution...
I made it work. I flashed TWRP with ODIN again but I unticked AutoReboot. When the flash was done I pulled the battery and rebooted straight to recovery. Since I had the new ROM on my SD-card I could flash it straight away.
Problem solved!

Flashing Rom

Hello Everyone please help me about note 4 update to 6.0 and i have some question..
im form india but my note 4 is SM-N910P US or UK.. current version lollipop system update not work error shown because note in region...
please help about custom rom installation...
which custom rom work in SM-N910P??
i falsh custom rom after india sim locked or not?
please help Samsung care does not support to me because mobile is overseas
and main problem are hotspot option not avabel in lollipop..
thanx for support
King Of Ego's Heart said:
Hello Everyone please help me about note 4 update to 6.0 and i have some question..
im form india but my note 4 is SM-N910P US or UK.. current version lollipop system update not work error shown because note in region...
please help about custom rom installation...
which custom rom work in SM-N910P??
i falsh custom rom after india sim locked or not?
please help Samsung care does not support to me because mobile is overseas
and main problem are hotspot option not avabel in lollipop..
thanx for support
Click to expand...
Click to collapse
The n910p is the Sprint model. You can update your firmware with Odin, just use the the sprint tar files.
If your not gonna use Sprint service, your first gonna want to make sure the sim is unlocked. Either with a paid service or some other way. There are threads at the Sprint forum for this! Search and read through them. Like GT tools. I am not very knowledgeable in this matter so ask I one of them threads.
Once you make sure your unlocked, if your using gsm service, you can pretty much flash any snapdragon Rom! All you need is to flash a Sprint kernel and correct data fix with the Rom you want.
Also Before you do anything, make a complete backup with twrp! Also make another one once you get unlocked.
The Rom you decide to install will determine which firmware you need before hand.
Once or if your already sim unlocked, and you pick a Rom out that you'd like to install, I can help.
Are you unlocked? Do you know how to use Odin? How to flash and use twrp?
What firmware are you currently on?
aaron74 said:
The n910p is the Sprint model. You can update your firmware with Odin, just use the the sprint tar files.
If your not gonna use Sprint service, your first gonna want to make sure the sim is unlocked. Either with a paid service or some other way. There are threads at the Sprint forum for this! Search and read through them. Like GT tools. I am not very knowledgeable in this matter so ask I one of them threads.
Once you make sure your unlocked, if your using gsm service, you can pretty much flash any snapdragon Rom! All you need is to flash a Sprint kernel and correct data fix with the Rom you want.
Also Before you do anything, make a complete backup with twrp! Also make another one once you get unlocked.
The Rom you decide to install will determine which firmware you need before hand.
Once or if your already sim unlocked, and you pick a Rom out that you'd like to install, I can help.
Are you unlocked? Do you know how to use Odin? How to flash and use twrp?
What firmware are you currently on?
Click to expand...
Click to collapse
sim are unlocked but i have no idea to odin and twrp flash yes other mobile i used custom rom but note 4 not use
King Of Ego's Heart said:
sim are unlocked but i have no idea to odin and twrp flash yes other mobile i used custom rom but note 4 not use
Click to expand...
Click to collapse
This thread has most of the sprint note 4 stock firmware files and Odin: https://forum.xda-developers.com/note-4-sprint/general/stock-tar-odin-flashable-t3250864
Here are official USB drivers: http://org.downloadcenter.samsung.c...G_USB_Driver_for_Mobile_Phones_v1.5.45.00.exe
Here is official Twrp 3.02: https://dl.twrp.me/trltespr/twrp-3.0.2-0-trltespr.img.tar.html This is installed from Odin!
Uninstall any Samsung software you have on pc for best results.
Download and install USB drivers to pc.
Download and unzip Odin to pc.
Download twrp.
1st thing I recommend is making a full backup.
So let's install twrp!
1. So put phone in download mode. (Turn off then hold power+vol dwn+home) then it'll prompt you to push vol up.
2. Open odin as admin.
3. Plug phone in pc USB. Odin should recognize phone.
4. In Odin. Click options, unclick auto reboot. Only 'F Reset time's should be checked. Now go back to log tab.
5. Click the AP button. And load the twrp file.
6. Click start. Do not touch pc or phone. Let it be. When the log states all threads completed. Wait 1 minute just to be safe. Unplug phone. Pull out battery. Put back in.
7. Boot into recovery. Press and hold (pwr+vol up+home)
You should now have twrp.
Goto backup and backup all partitions. If your not worried about your installed stuff, you don't need to backup 'data'.
Main thing is (boot,system,efs,modem)
Save this backup somewhere safe.
---------- Post added at 12:14 PM ---------- Previous post was at 11:41 AM ----------
King Of Ego's Heart said:
sim are unlocked but i have no idea to odin and twrp flash yes other mobile i used custom rom but note 4 not use
Click to expand...
Click to collapse
Part 2. Info!
If your just looking to install stock Rom. All you need is Odin and the stock tar file. But you select auto reboot in Odin.
You only deselect auto reboot when flashing twrp, because it won't stick.
Also once you upgrade to ok1 there is no downgrading.
If your looking to instal custom roms, you should read what firmware they recommend to have before hand. But most of them should work on most current firmware. It just depends.
In general this is what you'll do.
1. Odin the stock firmware you want. Let it boot.
2. Odin twrp.
3. Once you have twrp, flash any Rom you want for your phone.
4. Use a Sprint kernel (Ram) and data fix for international roms.
Edit. Once you upgrade your firmware, it's a good idea to make another backup of it. Especially the EFS.

Help recovering data

So I have a friend who decided to mess with his phone, of course without doing a backup, and now he's stuck in a situation that it can't boot even into recovery.
Currently all I see when booting to recovery:
Recovery Booting. . . . .
Set Warranty Bit : recovery
The phone is G900F
He has no idea what version was installed on it before.
I don't need the phone to boot, I need to recover the files on it.
Being a oneplus person myself, I'm not that familiar with samsung phones (my latest samsung was s2).
I've tried to install with odin (3.0.7 - if that matters) the following recoveries:
official twrp 2.8.7
twrp
cwm
All these recoveries showed "Recovery is not seandroid enforcing" message as well as the above when trying to boot into recoveries.
I've tried the official recovery as well:
https://forum.xda-developers.com/galaxy-s5/general/sm-g900f-stock-recovery-5-0-lollipop-t3228871
which removed the "seandroid" message, but that's all.
Not sure what I'm missing.
Any help would be appreciated!
Tahvok said:
So I have a friend who decided to mess with his phone, of course without doing a backup, and now he's stuck in a situation that it can't boot even into recovery.
Currently all I see when booting to recovery:
Recovery Booting. . . . .
Set Warranty Bit : recovery
The phone is G900F
He has no idea what version was installed on it before.
I don't need the phone to boot, I need to recover the files on it.
Being a oneplus person myself, I'm not that familiar with samsung phones (my latest samsung was s2).
I've tried to install with odin (3.0.7 - if that matters) the following recoveries:
official twrp 2.8.7
twrp
cwm
All these recoveries showed "Recovery is not seandroid enforcing" message as well as the above when trying to boot into recoveries.
I've tried the official recovery as well:
https://forum.xda-developers.com/galaxy-s5/general/sm-g900f-stock-recovery-5-0-lollipop-t3228871
which removed the "seandroid" message, but that's all.
Not sure what I'm missing.
Any help would be appreciated!
Click to expand...
Click to collapse
Hmm...
I see that your friend messed up his phone very well .....
Hopefully the eMMC memory is not corrupted becuase then only motherboard replacement would be necessary.
Summarising what you wrote:
1. you flashed "official recovery 2.8.7" -> where did you get it from? 2.8.7 is the very old version!
2. you flashed unofficial TWRP very old (2014) recovery (I checked your link)
3. you flashed unofficial CWM very old (2014) recovery (I checked your link)
4. finally you flashed stock, from old OS 5.0 Lollipop recovery provided from entrusted source - nobody reported that it works in the thread.
I listed this for you in order to underline one thing - READ, READ, READ, ASK, ASK, ASK .... before flashing anything to the phone and tell it to your friend.
Le's start with flashing from ODIN ver 3.12.7 (I am using it) this version of TWRP:
twrp-3.1.1-0-klte.img.tar for G900F which is the latest official recovery:
https://twrp.me/samsung/samsunggalaxys5qualcomm.html
Read how to flash it with odin method (when you open the link).
Edit: Are you sure the phone is SM-G900F? Please check model number on the label under battery (inside the phone).
Edit2: When you enter odin mode check phone model version as well - it is provided by installed bootloader.
Many40 said:
Hmm...
I see that your friend messed up his phone very well .....
Hopefully the eMMC memory is not corrupted becuase then only motherboard replacement would be necessary.
Summarising what you wrote:
1. you flashed "official recovery 2.8.7" -> where did you get it from? 2.8.7 is the very old version!
2. you flashed unofficial TWRP very old (2014) recovery (I checked your link)
3. you flashed unofficial CWM very old (2014) recovery (I checked your link)
4. finally you flashed stock, from old OS 5.0 Lollipop recovery provided from entrusted source - nobody reported that it works in the thread.
I listed this for you in order to underline one thing - READ, READ, READ, ASK, ASK, ASK .... before flashing anything to the phone and tell it to your friend.
Le's start with flashing from ODIN ver 3.12.7 (I am using it) this version of TWRP:
twrp-3.1.1-0-klte.img.tar for G900F which is the latest official recovery:
https://twrp.me/samsung/samsunggalaxys5qualcomm.html
Read how to flash it with odin method (when you open the link).
Edit: Are you sure the phone is SM-G900F? Please check model number on the label under battery (inside the phone).
Edit2: When you enter odin mode check phone model version as well - it is provided by installed bootloader.
Click to expand...
Click to collapse
First, thank you for trying to help me!
Please see attachments:
https://drive.google.com/folderview?id=1euC7-CoBeeUQxTGXQnPPgRE2-5VxFXLh
You can see that it is indeed g900f. I've also checked under the battery.
I've flashed the recovery you asked, however I could not find odin 3.12.7 only 3.12.10, so I've flashed with that (the odin thread on xda does not provide a link for 3.12.7 download).
You can see that it's still not booting with that recovery, it's just stuck at "booting recovery" screen.
I'm thinking perhaps it has a bad bootloader? How would you suggest to proceed?
Tahvok said:
First, thank you for trying to help me!
Please see attachments:
https://drive.google.com/folderview?id=1euC7-CoBeeUQxTGXQnPPgRE2-5VxFXLh
You can see that it is indeed g900f. I've also checked under the battery.
I've flashed the recovery you asked, however I could not find odin 3.12.7 only 3.12.10, so I've flashed with that (the odin thread on xda does not provide a link for 3.12.7 download).
You can see that it's still not booting with that recovery, it's just stuck at "booting recovery" screen.
I'm thinking perhaps it has a bad bootloader? How would you suggest to proceed?
Click to expand...
Click to collapse
Ok. Let's continue ... I hope (as I had very similar situation) that the phone is not hardbricked and eMMC memory is not corrupted -> I faced this on my phone and finally had to replace motherboard.
But let's be optimistic:
1. For data recovery - I don't have a silver bullet for this but I found this software: http://www.recover-android-iphone.com/recover-android/how-to-recover-data-bricked-samsung.html
It needs working odin mode so under condition that it supports s5 G900F it should be able to restore some data.
2. For unbricking - I recommend to flash via odin the latest official Samsung stock firmware dedicated to your friend's country/region:
https://www.sammobile.com/firmwares/galaxy-s5/SM-G900F/
You must be registered to download the software. Link for odin 3.12.7 is available on the bottom of the download page.
Just to underline - odin flash most probably (anybody please confirm that) will wipe your data so be aware of that.
Good luck.
Many40 said:
Ok. Let's continue ... I hope (as I had very similar situation) that the phone is not hardbricked and eMMC memory is not corrupted -> I faced this on my phone and finally had to replace motherboard.
But let's be optimistic:
1. For data recovery - I don't have a silver bullet for this but I found this software: http://www.recover-android-iphone.com/recover-android/how-to-recover-data-bricked-samsung.html
It needs working odin mode so under condition that it supports s5 G900F it should be able to restore some data.
2. For unbricking - I recommend to flash via odin the latest official Samsung stock firmware dedicated to your friend's country/region:
https://www.sammobile.com/firmwares/galaxy-s5/SM-G900F/
You must be registered to download the software. Link for odin 3.12.7 is available on the bottom of the download page.
Just to underline - odin flash most probably (anybody please confirm that) will wipe your data so be aware of that.
Good luck.
Click to expand...
Click to collapse
Why a full firmware is needed? Perhaps I can flash only the parts required to get into recovery? I count mount the phone from recovery, that's why it's my priority.
I would like to know also if odin will wipe everything if flashing a full firmware?
Tahvok said:
Why a full firmware is needed?
Click to expand...
Click to collapse
Because it is commonly recommended way to unbrick a phone.
Perhaps I can flash only the parts required to get into recovery?
Click to expand...
Click to collapse
Perhaps, yes. But:
1. I don't exactly know what restricts your recovery to run properly. Flashing separate recovery failed.
2. You, for example, could try flashing separately one of the latest bootloaders dedicated to G900F from BL section with odin but I doubt it would help.
I count mount the phone from recovery, that's why it's my priority.
I would like to know also if odin will wipe everything if flashing a full firmware?
Click to expand...
Click to collapse
As far as I know yes but I am not 100% sure because I didn't try that myself on s5.
I would appreciate if somebody else confirms that.
Many40 said:
2. You, for example, could try flashing separately one of the latest bootloaders dedicated to G900F from BL section with odin but I doubt it would help.
Click to expand...
Click to collapse
Can you suggest a bootloader for me? I would like to try that first.
Tahvok said:
Can you suggest a bootloader for me? I would like to try that first.
Click to expand...
Click to collapse
In my opinion, if odin mode works then bootloader should be OK. But as you wish -
tell me first what stock firmware will you later on trying to flash on your friends phone or in which country the phone will be operated.
Many40 said:
In my opinion, if odin mode works then bootloader should be OK. But as you wish -
tell me first what stock firmware will you later on trying to flash on your friends phone or in which country the phone will be operated.
Click to expand...
Click to collapse
Hong Kong
Tahvok said:
Hong Kong
Click to expand...
Click to collapse
Latest available Firmware version for Hong Kong is G900FZHS1CQD1 however I can't find a separate flashable bootloader for you.
Generaly, in my opinion you might try any of the latest bootloaders compatible with SM-G900F phone (here you can find a collection: https://forum.xda-developers.com/showpost.php?p=54094068&postcount=3, I am on G900FXXS1CQI4) but again:
1. I doubt it will help for entering recovery;
2. I still recommend to flash complete stock firmware to unbrick the phone.
However if you anyway decide to try with a bootloader, flash it with odin from BL section (untick auto reboot). Also turn off the phone before and after flashing and pull out battery for about 30 sec. It happens that bootloader doesn't flash properly at once even the odin says "PASS" so some people reported that they needed to repeat flashing a few times. I managed to flash bootloader at first time.
Unfortunateely the phone is not with me anymore, so I won't be able to continue testing. Thank you anyway for trying to help me! I really appreciate your help!

C9 pro sm-c9008 rooting help

I need Help to root my C9 pro sm-c9008
Baseband version c9008ZMU1AQD3
In this China variant
We don't have twrp :/
I hope someone can help me in this problem ?
You can try twrp by travis82 here.
https://forum.xda-developers.com/c9-pro/development/twrp-c9ltechn-t3646970
It has been confirmed that it works for variant devices like yours. Good luck.
Are u sure that this will work for c9008
Since there is no reference to c9008
Only to c9000
You sure this will work?
alisami2000 said:
I need Help to root my C9 pro sm-c9008
Baseband version c9008ZMU1AQD3
In this China variant
We don't have twrp :/
I hope someone can help me in this problem ?
Click to expand...
Click to collapse
C900F or C9009 ?
It's C9008
Just search on Google this model Number
It's new China Variant
SRISRIANDROID said:
C900F or C9009 ?
Click to expand...
Click to collapse
C9008
Check Google for this model number
It's China New Variant
alisami2000 said:
C9008
Check Google for this model number
It's China New Variant
Click to expand...
Click to collapse
k.k
alisami2000 said:
I need Help to root my C9 pro sm-c9008
Baseband version c9008ZMU1AQD3
In this China variant
We don't have twrp :/
I hope someone can help me in this problem ?
Click to expand...
Click to collapse
I have same model and already used last version of TWRP app and flashed cooked roms of C9000 & C900F successfully.
amincom said:
I have same model and already used last version of TWRP app and flashed cooked roms of C9000 & C900F successfully.
Click to expand...
Click to collapse
Bro i also have c9008 can you please tell me how can i get twrp in this? and can i download firmware of c9000 to my c9008?
taimoorali12 said:
Bro i also have c9008 can you please tell me how can i get twrp in this? and can i download firmware of c9000 to my c9008?
Click to expand...
Click to collapse
If you mean official stock rom it's not possible because it should be same model but for custom rom please follow the following steps:
Requirements download links:
Samsung USB driver http://download.cnet.com/Samsung-USB-Driver-for-Mobile-Phones/3001-18493_4-77538415.html
Odin https://odindownload.com/download/
TWRP download link https://androidfilehost.com/?fid=673791459329068931
Rom : Nougat C9000ZHU1BQL3 Debloated: https://androidfilehost.com/?fid=673791459329068625
(Source:https://forum.xda-developers.com/c9-pro/development/rom-stock-rooted-debloated-deodexed-t3702643)
Steps:
1-Copy downloaded rom to external SD card of your phone
2-Activate development mode in your phone then turn on OEM Unlock & USB Debugging
3-Install Samsung USB driver to your PC
4-Start your phone in download mode (Power off your phone and press 3 keys in same time (Power+home+volume down) to start up
5-connect your phone to pc and run Odin app then press Volume Up of your phone
6-Flash TWRP app to your Phone
7-disconnect the phone from PC and start it in recovery mode (Power+home+volume up)
8-Twrp will start then format system & data and select install, locate downloaded rom on SD card to flash it and after finished select wipe Cache and reboot.
amincom said:
If you mean official stock rom it's not possible because it should be same model but for custom rom please follow the following steps:
Requirements download links:
Samsung USB driver http://download.cnet.com/Samsung-USB-Driver-for-Mobile-Phones/3001-18493_4-77538415.html
Odin https://odindownload.com/download/
TWRP download link https://androidfilehost.com/?fid=673791459329068931
Rom : Nougat C9000ZHU1BQL3 Debloated: https://androidfilehost.com/?fid=673791459329068625
(Source:https://forum.xda-developers.com/c9-pro/development/rom-stock-rooted-debloated-deodexed-t3702643)
Steps:
1-Copy downloaded rom to external SD card of your phone
2-Activate development mode in your phone then turn on OEM Unlock & USB Debugging
3-Install Samsung USB driver to your PC
4-Start your phone in download mode (Power off your phone and press 3 keys in same time (Power+home+volume down) to start up
5-connect your phone to pc and run Odin app then press Volume Up of your phone
6-Flash TWRP app to your Phone
7-disconnect the phone from PC and start it in recovery mode (Power+home+volume up)
8-Twrp will start then select install and locate downloaded rom on SD card to flash it and after finished select wipe Cache and reboot.
Click to expand...
Click to collapse
is this safe? because here we are trying to install the rom of c9000 in c9008?
---------- Post added at 09:35 PM ---------- Previous post was at 09:20 PM ----------
amincom said:
If you mean official stock rom it's not possible because it should be same model but for custom rom please follow the following steps:
Requirements download links:
Samsung USB driver http://download.cnet.com/Samsung-USB-Driver-for-Mobile-Phones/3001-18493_4-77538415.html
Odin https://odindownload.com/download/
TWRP download link https://androidfilehost.com/?fid=673791459329068931
Rom : Nougat C9000ZHU1BQL3 Debloated: https://androidfilehost.com/?fid=673791459329068625
(Source:https://forum.xda-developers.com/c9-pro/development/rom-stock-rooted-debloated-deodexed-t3702643)
Steps:
1-Copy downloaded rom to external SD card of your phone
2-Activate development mode in your phone then turn on OEM Unlock & USB Debugging
3-Install Samsung USB driver to your PC
4-Start your phone in download mode (Power off your phone and press 3 keys in same time (Power+home+volume down) to start up
5-connect your phone to pc and run Odin app then press Volume Up of your phone
6-Flash TWRP app to your Phone
7-disconnect the phone from PC and start it in recovery mode (Power+home+volume up)
8-Twrp will start then select install and locate downloaded rom on SD card to flash it and after finished select wipe Cache and reboot.
Click to expand...
Click to collapse
can i just flash this rom using odin?
I'm using same model C9008 and already applied it and using to post this reply so it's safe if you know how to do.
You can't use odin to flash custom rom because it's file is in differnet format.
Sent from my SM-C9000 using Tapatalk
Guys I have tried TWRP but it isn't working
The TWRP gives me error
So TWRP is not compatible with sm-c9008?
Any way to do TWRP
On this Variant?
alisami2000 said:
Guys I have tried TWRP but it isn't working
The TWRP gives me error
So TWRP is not compatible with sm-c9008?
Any way to do TWRP
On this Variant?
Click to expand...
Click to collapse
It's work great with my C9008,please refer to my previous reply#10 for details.
alisami2000 said:
I need Help to root my C9 pro sm-c9008
Baseband version c9008ZMU1AQD3
In this China variant
We don't have twrp :/
I hope someone can help me in this problem ?
Click to expand...
Click to collapse
I too have samsung c9 pro sm-c9008 (china variant)
only marshmellow is available yet, but sm-c9000 roms also supported,and you have the latest firmware and the international apps.
i took a smart switch backup and then flashed twrp (c9ltechn) and flash with LATEST odin then your firmware will corrupt and wont work, but you have taken your backup, then download latest SM-C9000 firmware (i recommend hong kong region, im using too) flash it and restore your samsung smart switch backup.
Now your running the international version of c9 pro. (BUT ROOTING THE PHONE IS ALMOST IMPOSSIBLE)
Bilal54 said:
I too have samsung c9 pro sm-c9008 (china variant)
only marshmellow is available yet, but sm-c9000 roms also supported,and you have the latest firmware and the international apps.
i took a smart switch backup and then flashed twrp (c9ltechn) and flash with LATEST odin then your firmware will corrupt and wont work, but you have taken your backup, then download latest SM-C9000 firmware (i recommend hong kong region, im using too) flash it and restore your samsung smart switch backup.
Now your running the international version of c9 pro. (BUT ROOTING THE PHONE IS ALMOST IMPOSSIBLE)
Click to expand...
Click to collapse
Hey can you provide the links and details that how did you ran the c9000 firmware on c9008
zaib5611 said:
Hey can you provide the links and details that how did you ran the c9000 firmware on c9008
Click to expand...
Click to collapse
Proceed at your own risk!
1. Download latest odin tool.
2. Download twrp for china variant: https://twrp.me/samsung/c9ltechn.html.
3. Flash twrp and check if stock rom is not corrupted, if not, nandroid backup.
4. Now wipe everything in the phone.
5. Download rom (nougat), SM-9000 firmware is compatible with the SM-9008 hardware (check my image attached) but download the "hong kong" region firmware. Basically your changing your Asia phone to an international phone.
https://www.sammobile.com/firmwares/galaxy-c9-pro/SM-C9000/TGY/download/C9000ZHU1BQL3/200864/
(If you want different sites... Google "samsung c9 pro hong kong nougat stock firmware" and download the sm-c9000 rom and flash it)
NOW AFTER THIS YOUR PHONES IN INTERNATIONAL STATE. DO NOT FLASH CUSTOM RECOVERY AGAIN, IT WILL SOFTBRICK!!!!
ENJOY USING YOUR NEW ROM. ? feel free to clear more doubts.
Bilal54 said:
Proceed at your own risk!
1. Download latest odin tool.
2. Download twrp for china variant: https://twrp.me/samsung/c9ltechn.html.
3. Flash twrp and check if stock rom is not corrupted, if not, nandroid backup.
4. Now wipe everything in the phone.
5. Download rom (nougat), SM-9000 firmware is compatible with the SM-9008 hardware (check my image attached) but download the "hong kong" region firmware. Basically your changing your Asia phone to an international phone.
https://www.sammobile.com/firmwares/galaxy-c9-pro/SM-C9000/TGY/download/C9000ZHU1BQL3/200864/
(If you want different sites... Google "samsung c9 pro hong kong nougat stock firmware" and download the sm-c9000 rom and flash it)
NOW AFTER THIS YOUR PHONES IN INTERNATIONAL STATE. DO NOT FLASH CUSTOM RECOVERY AGAIN, IT WILL SOFTBRICK!!!!
ENJOY USING YOUR NEW ROM. feel free to clear more doubts.
Click to expand...
Click to collapse
Thank u very much for the reply. how can i check that that my stock rom is not corrupted. and what is nandroid backup. and my phone is not having the oem unlock option as well.
zaib5611 said:
Thank u very much for the reply. how can i check that that my stock rom is not corrupted. and what is nandroid backup.
Click to expand...
Click to collapse
No. since your changing your rom, the rom your currently using might get corrupted after flashing the TWRP. If it doesn't get corrupted, boot to custom recovery(TWRP) and backup your current rom (BACKUP>SYSTEM).
If your rom is corrupted (when restarting your phone after flashing custom recovery(TWRP) the phone will be soft bricked) but you dont need to worry because you can flash back the new sm-c9000 rom. ?
---------- Post added at 11:13 AM ---------- Previous post was at 11:04 AM ----------
zaib5611 said:
Thank u very much for the reply. how can i check that that my stock rom is not corrupted. and what is nandroid backup. and my phone is not having the oem unlock option as well.
Click to expand...
Click to collapse
Download the CROM.apk https://www.apkmirror.com/apk/samsu...ease/crom-service-1-0-4-android-apk-download/
Enable Developer Option by navigating to your Settings > About > Software Information > More > Build Number. You need to tap the Build Number option more than 5 times or until you get a pop-up ‘Developer Option Enabled’
Navigate to Settings > Developer Option and enable OEM Unlock
Install the downloaded CROM Services app and disable Samsung Reactivation Lock.
Run the CROM Service app and tap ‘Unlock Bootloader’.
Bilal54 said:
No. since your changing your rom, the rom your currently using might get corrupted after flashing the TWRP. If it doesn't get corrupted, boot to custom recovery(TWRP) and backup your current rom (BACKUP>SYSTEM).
If your rom is corrupted (when restarting your phone after flashing custom recovery(TWRP) the phone will be soft bricked) but you dont need to worry because you can flash back the new sm-c9000 rom.
---------- Post added at 11:13 AM ---------- Previous post was at 11:04 AM ----------
Download the CROM.apk https://www.apkmirror.com/apk/samsu...ease/crom-service-1-0-4-android-apk-download/
Enable Developer Option by navigating to your Settings > About > Software Information > More > Build Number. You need to tap the Build Number option more than 5 times or until you get a pop-up ‘Developer Option Enabled’
Navigate to Settings > Developer Option and enable OEM Unlock
Install the downloaded CROM Services app and disable Samsung Reactivation Lock.
Run the CROM Service app and tap ‘Unlock Bootloader’.
Click to expand...
Click to collapse
VERY grateful, but still no OEM Unlock option in the Developer Option .. and are you from pakistan

verification failed after root s7 edge nougat (CANT ROOT MY PHONE)

Hello I have the S7 edge g935f nougat 7.0 , I flashed the twrp last version, got into twrp, flashed the SuperSU, and then after reboot said verification failed etc.. I flashed a stock rom which has the December security patch probably that's the reason why says that... I tried to flash the rom again, then flash first a dm-verify zip and then SuperSU (tried with magisk too) but nothing changed.. what to do ?
This is for Exynos
1.Turn on Odin3 and connect your phone to PC in Download Mode (hold "Power & Home & Volume -" for a while).
2.Download lastest custom recovery correctly for your model from offical TWRP website then unpack zip to get flashable *.tar file.
3.Put twrp-3.2.1-x-xxxxxx.img.tar file to "AP" tab.
4.In Options tab check only "F. Reset Time". ATTENTION: rest options must be UNCHECKED!!!
5.Press "Start" and wait till finish flashing (you will see "PASS" info as on THAT screenshot when flashing will be finished).
6.Press and hold "Power & Home & Volume -" for a while to reboot your device. Directly while phone rebooting (when display is turned off/black) press and hold "Power & Home & Volume +" till custom TWRP recovery menu shows up.
7.Go to "Wipe" menu, and swipe to right for "Factory Reset".
8.Now you can flash any zip file to your phone, so all custom ROM's & kernels & mods etc and also you can ROOT with lastest Magisk.zip or SuperSU.zip, etc.
Click to expand...
Click to collapse
Point 7 will wipe ALL youre data, but is a necessary step to root your device.
https://forum.xda-developers.com/galaxy-s7/how-to/guide-onelatest-stock-fw-csc-root-t3702963
jbakers said:
This is for equinox
Point 7 will wipe ALL youre data, but is a necessary step to root your device.
https://forum.xda-developers.com/galaxy-s7/how-to/guide-onelatest-stock-fw-csc-root-t3702963
Click to expand...
Click to collapse
What is equinox?
I want to flash the stock rom not a custom one because it's says you can flash any custom rom , after all steps can I flash again the stock rom ?
after i swipe right to factory reset my device says failed to mount '/data' (invaliod argument)
...done
Unable to mount storage
tried to flash the no-verify-opt-encryption zip but nothing changed ..
You need to go into TWRP straight after installing it and do the following:
Click Wipe --> Click right button that says "Format Data".
Type "yes" to continue
If that doesnt help:
How to solve problem with mounting "/data" in TWRP?
1.Flash THAT package via TWRP or go to CF-Auto-Root website, download package for your model and stock firmware on which you are/were and just flash it via Odin3
StonebridgeGr said:
What is equinox?
Click to expand...
Click to collapse
Sorry Exynos, was half asleep...
Its which SOC it uses:
Samsung Exynos 8890 Model[edit]
SM-G935F (International Single Sim)
SM-G935FD (International Dual Sim)
SM-G935W8 (Canada)
SM-G935S (South Korea SK Telecom)
SM-G935K (South Korea KT)
SM-G935L (South Korea LG U+)
Qualcomm Snapdragon 820 Model[edit]
SM-G9350 (China Open Model, Hong Kong)
SM-G935V (USA Verizon Wireless)
SM-G935A (USA AT&T)
SM-G935P (USA Sprint)
SM-G935T (USA T-Mobile US)
SM-G935U (USA Samsung Unlocked)
SM-G935R4 (USA US Cellular)
SC-02H (Japan NTT DoCoMo)
SCV33 (Japan KDDI au)
SM-G935U (USA Unlocked)
https://en.wikipedia.org/wiki/Samsung_Galaxy_S7#Galaxy_S7_Edge
jbakers said:
You need to go into TWRP straight after installing it and do the following:
Click Wipe --> Click right button that says "Format Data".
Type "yes" to continue
If that doesnt help:
How to solve problem with mounting "/data" in TWRP?
1.Flash THAT package via TWRP or go to CF-Auto-Root website, download package for your model and stock firmware on which you are/were and just flash it via Odin3
Click to expand...
Click to collapse
After i flash that file i can go to the twrp again and flash the magisk or supersu??
jbakers said:
You need to go into TWRP straight after installing it and do the following:
Click Wipe --> Click right button that says "Format Data".
Type "yes" to continue
If that doesnt help:
How to solve problem with mounting "/data" in TWRP?
1.Flash THAT package via TWRP or go to CF-Auto-Root website, download package for your model and stock firmware on which you are/were and just flash it via Odin3
Click to expand...
Click to collapse
did that but after reboot the phone bootloop ..... restarted itself while its on samsung logo, i must flash the stock rom again , so nothing changed .. what to do ?
I need someone's help me i want so much to root my phone with magisk tool, also keep in mind the phone is second hand and it had a austria firmware . i dont know if that matters, now the current stock rom is a greek COSMOTE.. before that with the austria firmware i could normally flash the phone i tried only with SuperSU tho .. when i say greek or austria firmware i mean the CSC if i am right
StonebridgeGr said:
I need someone's help me i want so much to root my phone with magisk tool, also keep in mind the phone is second hand and it had a austria firmware . i dont know if that matters, now the current stock rom is a greek COSMOTE.. before that with the austria firmware i could normally flash the phone i tried only with SuperSU tho .. when i say greek or austria firmware i mean the CSC if i am right
Click to expand...
Click to collapse
Dont know where is the problem, are you following steps correctly? Install twrp > wipe all data > flash rom > flash super SU / magisk . Also don't flash carrier firmwares, flash the correct carrier free firmware for your region IF your phone is NOT carrier locked.
Sent from my S7 Edge using XDA Labs
shah22 said:
Dont know where is the problem, are you following steps correctly? Install twrp > wipe all data > flash rom > flash super SU / magisk . Also don't flash carrier firmwares, flash the correct carrier free firmware for your region IF your phone is NOT carrier locked.
Sent from my S7 Edge using XDA Labs
Click to expand...
Click to collapse
i dont want custom rom, only the stock
i cant any files throught twrp i tried multiple version of twrp.. if i try to flash something and then reboot my devices says that thing about encryption .. also i get error about mount /data tried to format data but if i format them then the firmware will be wiped , so i have to flash the firmware from begin ..
StonebridgeGr said:
i cant any files throught twrp i tried multiple version of twrp.. if i try to flash something and then reboot my devices says that thing about encryption .. also i get error about mount /data tried to format data but if i format them then the firmware will be wiped , so i have to flash the firmware from begin ..
Click to expand...
Click to collapse
See this https://forum.xda-developers.com/s7-edge/development/rom-s7-edge-rom-v1-1-t3356699
See the beginner section,
Also see this
https://forum.xda-developers.com/galaxy-s7/how-to/root-official-stock-nougat-7-0-100-t3540765
And this too
https://forum.xda-developers.com/s7-edge/development/samsung-systemless-devbase-encryption-t3517178
You should be doing a mistake somewhere. Good luck
Sent from my S7 Edge using XDA Labs
shah22 said:
See this https://forum.xda-developers.com/s7-edge/development/rom-s7-edge-rom-v1-1-t3356699
See the beginner section,
Also see this
https://forum.xda-developers.com/galaxy-s7/how-to/root-official-stock-nougat-7-0-100-t3540765
And this too
https://forum.xda-developers.com/s7-edge/development/samsung-systemless-devbase-encryption-t3517178
You should be doing a mistake somewhere. Good luck
Click to expand...
Click to collapse
Dude if i format the phone from twrp and then reboot the system says there is no OS....
StonebridgeGr said:
Dude if i format the phone from twrp and then reboot the system says there is no OS....
Click to expand...
Click to collapse
Bro, then you should flash the rom through twrp ! Put rom on sd card and flash. Then flash super su. I advise you to watch video tutorials on the links i provided above.
Sent from my S7 Edge using XDA Labs
shah22 said:
Bro, then you should flash the rom through twrp ! Put rom on sd card and flash. Then flash super su. I advise you to watch video tutorials on the links i provided above.
Click to expand...
Click to collapse
Ahahah you talk me like I don't know about android but you don't get it.. I want the stock ROM of Odin.. not a custom.. but I install the superman ROM you send above.. it helped me so far. Thank you so much
StonebridgeGr said:
Ahahah you talk me like I don't know about android but you don't get it.. I want the stock ROM of Odin.. not a custom.. but I install the superman ROM you send above.. it helped me so far. Thank you so much
Click to expand...
Click to collapse
No, i will never think that anyone has lesser knowledge than mine, i am a newbie myself. But why you wipe all internal memory ? If you want stock then only format data and cache/dalvik. Also use system less root or otherwise you will get dm verity fail error. You can also flash no verity opt encrypt to bypass this error if you don't want to use system less root.
Sent from my S7 Edge using XDA Labs
shah22 said:
No, i will never think that anyone has lesser knowledge than mine, i am a newbie myself. But why you wipe all internal memory ? If you want stock then only format data and cache/dalvik. Also use system less root or otherwise you will get dm verity fail error. You can also flash no verity opt encrypt to bypass this error if you don't want to use system less root.
Click to expand...
Click to collapse
I flashed the superman ROM which is like the stock the UI and it has more features.. but the battery is draining faster than the stock.. maybe a cpu governor can help that ?
StonebridgeGr said:
I flashed the superman ROM which is like the stock the UI and it has more features.. but the battery is draining faster than the stock.. maybe a cpu governor can help that ?
Click to expand...
Click to collapse
Ofcourse, there is a whole lot of tweaking when using custom kernels/roms. But be careful, as these tweakings requires much research as it could also damage the hardware if done the wrong way. My advice still is to go back to everything stock and then root it using twrp and super su. Again, don't wipe all internal storage, only data and dalvik cache. Good luck
Sent from my S7 Edge using XDA Labs

Categories

Resources