Hey all,
Was attempting to get to systemless root for Android Pay after being on a standard system-modified root. Followed the guide linked below:
http://forum.xda-developers.com/nexus-6p/themes-apps/systemless-root-themed-apps-t3292105
All went well until I attempted to install a Layers theme and got a SystemUI crash. No worries, restored from TWRP backup made just before Layers. Still bootlooped. Attempted to restore my Nandroid backup, still no dice. Any idea what might be wrong? Thanks for any help.
ever get it fixed? and how I am assuming you resolved?
I fixed being stuck in boot after a restore by only flashing system, data, boot, and vendor in TWRP.
proper vendor image?
From what I have read lately, Systemless root doesn't work with Android Pay any more. Google has patched it a month ago.
Read: http://www.xda-developers.com/android-pay-no-longer-working-with-systemless-root/
About TWRP restore. The function has evolved to be a little complex than earlier, and many users, especially those who are new, seem to have problems with it. You should most probably backup the old entries, like System, Data, Cache, and Boot. Vendor could be left alone if you're not downgrading or upgrading. Same goes for the recovery, since TWRP will be there already.
You should of did a total wipe, factory reset plus system. Then tried restore. You might of also needed to delete overlays folder.
Related
Recently installed Hyperdrive Rom on my Verizon Note 3. SM-900V, NC4, running KK 4.4.2 prior to this installation.
Followed instructions re flashing back to NC2, Rom installed, everything is good,
BTW, as a part of the process installed SafeStrap, which provided a nice TWRP related recovery.
Did as suggested, a backup through recovery.
subsequently, made a couple of other changes, making a new backup through recovery each time. At present, there are three recoveries in backup.
Now comes the problem...........Decided to restore a prior backup, as instructed, did the full wipe using SS recovery, selected restore file desired, all went well and rebooted phone, only to have it hang once it reached the Bright Red Verizon screen.
Rebooted to recovery, followed the above procedure two other times on the remaining two backups. Same results.
Have wiped (Factory reset) each time in recovery with no apparent success.
Is this now being caused by the fact that I'm @ NC2, rather than NC4?
Would appreciate any suggestions as how I can get back to being able to restore and use any of the prior backups.
As a temporary measure, I went into recovery and reinstalled the Hyperdrive rom but would like to be able to go back in time if possible, and for no other reason to be able to understand just exactly what is causing this issue. Perhaps others have the same and have resolved in some way. A Google search shows that some are suggesting a return to factory settings, i.e. a full wipe through recovery, however I've done that with no success.
Another question, what happens if I also "wipe" the system files as well as dalvic, cache and data? Have hesitated to do that for fear of the unknown consequences
I was bootloader unlocked, latest TWRP installed, systemless root with SuperSU 2.6, cataclysm rom, ex kernel, layers, xposed. I had made a ton of backups and even kept some of them backed up in another locations. I needed to restore a backup in TWRP. At first it wouldn't let me, kept saying that phone system was mounted as read only.
this is my question #1 - How do you mount system for read in TWRP? I see there's an option called "mount," I go in there, i see settings I can select, but I don't see any option to "execute" or "apply" settings (like TWRP has on other screens - swipe to backup, swipe to restore, etc). There's no "clicke here to mount option." what do you do here?
#2 - it finally mounted rw, i think, but after picking my latest backup, it started and then when it got to 19% it reboot the phone. Phone is softbricked.
#3 - I'm very confused about all the checkboxes to restore, and all the checkboxes to wipe.
What should I be wiping and what should I be restoring? When making backups I checked all the boxes.
I had the galaxy nexus before and I knew that phone and clockworck mod inside out. TWRP is confusing and glitchy to me. I'm stuck and work with a phone without an OS and I'm starting to freak out, and don't have A to C cables with me.
Please explain where I went wrong here and how to do things correctly. I want to understand what I'm doing better, not just follow steps.
When you restored, with all the check boxes did you click "system image" for restore?
You should wipe then restore only system, data, and boot.
dontbeweakvato said:
When you restored, with all the check boxes did you click "system image" for restore?
You should wipe then restore only system, data, and boot.
Click to expand...
Click to collapse
Yes, I selected all the boxes, including system image I believe.
I did a wipe. I selected all the boxes. Went back into TWRP and now all my backups are gone. I said reboot, and TWRP said there's no OS installed. I think I deleted everything. I should not have wiped. I do have a backup saved on a computer, it's a folder with lots of .img files inside. How can I get that onto my phone with only having fastboot and TWRP modes available? I mean how can I place it on the phone in a way that TWRP would recognize it and restore from it.
I ended up just flashing the stock google image and that at least gave me a working phone back.
Yes. You beat me to it, that's what I was going to say. You have to reflash. Just remember for future references you only need to backup boot, system, and data( and efs etc). But Not "system image" that'll Bork your stuff up.
dontbeweakvato said:
Yes. You beat me to it, that's what I was going to say. You have to reflash. Just remember for future references you only need to backup boot, system, and data( and efs etc). But Not "system image" that'll Bork your stuff up.
Click to expand...
Click to collapse
I'd like to really understand this better. Do you know why system image borks the phone? Also, when you say efs etc., do you mean "absolutely everything except system image"? (I actually didn't see EFS listed there)
Well boot system and data. But you also need efs cause thats your imei. So just look around and familiarize with what youve found so far. Right now Im trying to flash 6.0.1 with a systemless root. Its kinda goin ridiculous right now because there aren't any directions or suggestions.
If you get to "no OS installed" restoring system image, then system will get you back
Sent from my Nexus 6P using Tapatalk
zgroten said:
If you get to "no OS installed" restoring system image, then system will get you back
Sent from my Nexus 6P using Tapatalk
Click to expand...
Click to collapse
After it said no OS installed, I tried to restore system image from my TWRP backup, and the restore failed and the phone reboot itself at 19% restored. I had to ADB flash the factory system image from google. This brings me back to the original question.
Why was the restore in TWRP failing?
Did you mount system in TWRP before attempting to restore?
Sent from my Nexus 6P using Tapatalk
mistermojorizin said:
After it said no OS installed, I tried to restore system image from my TWRP backup, and the restore failed and the phone reboot itself at 19% restored. I had to ADB flash the factory system image from google. This brings me back to the original question.
Why was the restore in TWRP failing?
Click to expand...
Click to collapse
actually in twrp you could of wiped, then restored boot, system , data and it would of restored everything
Hey,
I've had this problem for ages now, and always gave up on my data, but now I really want to fix this for good.
Yesterday I was ready to update my CM12 nightly to the lastest version (didn't see it was actually CM13), and did a backup in cwm before the update. The backup succeeded, but it gave the message that .android_secure couldn't be found and it didn't back that up. It always gives me this message after a backup and after google searching, it seems to me that it doesn't matter.
After installing the update, I noticed it was CM13, and my gapps wasn't updated to the marshmellow stock, as expected, so errors occured all the time.
I didn't want to upgrade to CM13 just yet, so I decided to restore my backup.
As always, the restore process goes without errors, but upon reboot I'm stuck at the CM logo. I can wait untill the battery is dead or ignites from the heat, but nothing happens. This has also happened to me every time I make a backup. I've watched about every video on youtube on how to do a proper backup and how to restore one, so I'm confident that I did it right.
For some reason, any backup I make, no matter what android version (didn't work with stock kitkat, either, before I switched to CM12) it never works and I'm forced to do a clean install and start over again.
I've tried to do partial restores from the backup file, and if I only restore the data partition (and wipe dalvik) It does boot, but gives me non stop errors that apps are crashing.
I've tried to do a dirty flash to no avail, always endless error messages.
When I do a clean install and check the MK5 of the backup with nandroid manager it gives no errors.
Is there anything wrong with my phone or something? I'm not making backups to be unable to restore them.
Can anyone help me out with this?
(I have a i9505)
Try a different recovery. CWM is outdated. TWRP is nice. Worked for ne every time. There are TWRP flashable zips so you won't have to mess around with Odin.
GDReaper said:
Try a different recovery. CWM is outdated. TWRP is nice. Worked for ne every time. There are TWRP flashable zips so you won't have to mess around with Odin.
Click to expand...
Click to collapse
Won't changing recovery make my old backups useless? I'm all for changing to TWRP, but first I'd love to restore my CWM backup...
Yes it will. Unfortunately I don't know what to suggest. Haven't used CWM since I switched to the S4.
I just got a s5. And I got it succesfully rooted and also got TWRP working on it.
All the data from my previous phone was transfered to the s5.
Now I made some backups with TWRP with the default settings: Partitions boot, system and data.
With the backups in mind I was thinking I could easily restore it to a previous state.
Thinking I backed up all the data and wanted to make it fresh again, I wanted to restore it.
In the menu I chose the restore option with the same settings as the backup: Partitions boot, system and data.
And it gives a message restoring system succesfull.
But when rebooting, it keeps hanging and at the moment of loading the android system every bit of the system keeps 'hanging'
It keeps saying
'Unfortunately touchwiz startup unsuccesfully'
'Unfortunately youtube startup unsuccesfully'
'Unfortunately greenify startup unsuccesfully'
'Unfortunately app whatever startup unsuccesfully'
And so on and so on
Eventually it starts with a black screen with nothing loaded. Complete blackout.
So this backup doesn't work. And I try my second backup.
Unfortunately also the second backup gave these errors.
And also the third backup!
So the backup files seem the right size, it's some gigabytes, and it alway's keeps saying backup/restore succesfully.
But now it fails to restore and boot the backup
The things I tried.
-Trying three different backups
-Wiping cleaning data/dalvik/cache etc etc
-Restoring a part of the backup. First system, then data, then boot, no succes.
So i'm totally lost! Does somebody know how to fix this? Or have some tips to try??
You can't restore system and boot from a different model phone
That would be like trying to flash a ROM for one model phone to another without porting it
If it was an S5 you backed up, was it the exact same model (ie: G900F etc?)
Flash back to stock, then try restoring only DATA
Or use TiBu to restore your apps from the TWRP backup
*Detection* said:
You can't restore system and boot from a different model phone
That would be like trying to flash a ROM for one model phone to another without porting it
If it was an S5 you backed up, was it the exact same model (ie: G900F etc?)
Flash back to stock, then try restoring only DATA
Or use TiBu to restore your apps from the TWRP backup
Click to expand...
Click to collapse
Thanks for the reply! It was a backup and restore on the same phone. So that is why I thought it was supposed to be a easy restore.
But I found the solution hidden somewhere in one message on XDA:
"Originally Posted by Dr. Fed
Would you happen to know why, when restoring a TW 4.4.2 nandroid using TWRP 2.8.1 or 2.8.4, after running an AOSP lollipop ROM like CM12, the TW ROM boots but then the whole system force-closes? Before restoring the nandroid, I advance wipe system, data, cache, and dalvik. Then I restore the nandroid. It boots, but then some daemon crashes. Then all processes and apps. The screen goes black after a few crashes.
So, what I do is pull out the battery, boot into recovery, advance wipe system, data, cache, dalvik, flash a CM11 ROM, reboot. I let CM11 start up, skip the set-up, then I boot back to TWRP (2.8.1 and now 2.8.4), advanced wipe, restore TW nandroid, and now it works just fine.
It seems like TWRP doesn't fully wipe."
Here the steps for if other people will run into the same problem:
Problem: Android 5 is running, with twrp 2.7 performed a back up = Restoring the backup is difficult because it problably doesn't do a clean wipe somehow.
1. I downloaded a cyanogen 11 rom, a Android 4 version.
2. Installed it with TWRP. Somehow it 'wipes' it more efficiently.
3. From cyanogen 11 back to booting TWRP.
4. In TWRP trying the Android 5 restore.
And Amazingly this worked!! = Celebrate!!
chokolademan said:
Thanks for the reply! It was a backup and restore on the same phone.
Click to expand...
Click to collapse
Confused me with this line
chokolademan said:
All the data from my previous phone was transfered to the s5.
Click to expand...
Click to collapse
Good to see you solved it
Attempt 1 to install Lineage
Tried installing the Lineage 14.1, it kept doing a blank-but-illuminated screen, then turned off and back on, resulting in a boot loop.
We tried a couple of things - first the more conservative wiping of just data, dalvik and cache.
This did the boot loop described above. I then restored the stock backup and all was well.
Attempt 2 to install Lineage
The second time we wiped the system partition in addition to the above. Same bootloop.
Went to restore the backup of stock again, but now it's getting stuck at "I'm not a phone I'm a comprehensive yada yada" screen. It never progresses past this.
Attempts to get Stock Restore working
We've tried restoring just the system, data and dalvik
We've also tried System Image in addition to these.
No joy.
We don't have a laptop or other device to hand for a few days so we have just what's on the phone - the Lineage 14.1 zip, the stock backup and TWRP.
Any ideas how we can get back to a working phone with either OS?
What type of LePro3 do you have?
X720,X722,X727?
It's the X722
kenbw2 said:
It's the X722
Click to expand...
Click to collapse
The X722 model is not supported by Lineage.
I think that you have a problem. Hope anyone can help you to go back to stock successfully.
When doing the stock restore, we didn't restore the boot image.
Is that something worth trying?
kenbw2 said:
When doing the stock restore, we didn't restore the boot image.
Is that something worth trying?
Click to expand...
Click to collapse
Yes, you could try it. Please, write, was it useful or not)
Success!
Restored System,. System Image, Cache, Data and Boot partitions and all is now back to normal.
Phew!
kenbw2 said:
Success!
Restored System,. System Image, Cache, Data and Boot partitions and all is now back to normal.
Phew!
Click to expand...
Click to collapse
That is great. So, is bluetooth works fine after that?