Hello, I am MrGovernor.
I have recently purchased a Galaxy Note 3 N9005 and decided to root it earlier today. The device is running on 4.3 because my carrier decide to delay their releases (O2).
About 2 hours ago I then decided to put a custom recovery on it before installing Omega ROM...
Now, me being a newb, I was following about 3 different tutorials at once; I managed to get to the final stage of using ODIN to flash CWM onto the phone (n9005-cwm-recovery-6.0.4.7-kk). Now, I did this and when my phone rebooted it got the initial loading screen and this message appeared:
RECOVERY BOOTING....
Click to expand...
Click to collapse
Set Warranty Bit : recovery
Click to expand...
Click to collapse
This happens when I go into Recovery Mode and when I boot normally. I can still go into download mode.
I am a newb, have I bricked my new phone or is there any way to salvage it?
Thanks a load!
MrGovernor.
MrGovernor said:
Hello, I am MrGovernor.
I have recently purchased a Galaxy Note 3 N9005 and decided to root it earlier today. The device is running on 4.3 because my carrier decide to delay their releases (O2).
About 2 hours ago I then decided to put a custom recovery on it before installing Omega ROM...
Now, me being a newb, I was following about 3 different tutorials at once; I managed to get to the final stage of using ODIN to flash CWM onto the phone (n9005-cwm-recovery-6.0.4.7-kk). Now, I did this and when my phone rebooted it got the initial loading screen and this message appeared:
This happens when I go into Recovery Mode and when I boot normally. I can still go into download mode.
I am a newb, have I bricked my new phone or is there any way to salvage it?
Thanks a load!
MrGovernor.
Click to expand...
Click to collapse
no its fine all n3 rooted will have that when and if you go back to stock it will go
jaythenut said:
no its fine all n3 rooted will have that when and if you go back to stock it will go
Click to expand...
Click to collapse
Thanks a load!
MrGovernor said:
Hello, I am MrGovernor.
I have recently purchased a Galaxy Note 3 N9005 and decided to root it earlier today. The device is running on 4.3 because my carrier decide to delay their releases (O2).
About 2 hours ago I then decided to put a custom recovery on it before installing Omega ROM...
Now, me being a newb, I was following about 3 different tutorials at once; I managed to get to the final stage of using ODIN to flash CWM onto the phone (n9005-cwm-recovery-6.0.4.7-kk). Now, I did this and when my phone rebooted it got the initial loading screen and this message appeared:
This happens when I go into Recovery Mode and when I boot normally. I can still go into download mode.
I am a newb, have I bricked my new phone or is there any way to salvage it?
Thanks a load!
MrGovernor.
Click to expand...
Click to collapse
it's normal
hhai2pth said:
it's normal
Click to expand...
Click to collapse
Now... Another issue...
I installed PhilZ Touch Recovery and that has worked fine...
However, I went full retard and 'Wiped System for a New ROM' before I made a backup...
I then tried to flash FoxHound ROM, I managed to get through the install process flawlessly, BUT, when the device rebooted it stays on the boot screen...
What can be done to fix this? As I failed to make a backup of my original 4.3 firmware...
Thanks Again!
MrGovernor said:
Now... Another issue...
I installed PhilZ Touch Recovery and that has worked fine...
However, I went full and 'Wiped System for a New ROM' before I made a backup...
I then tried to flash FoxHound ROM, I managed to get through the install process flawlessly, BUT, when the device rebooted it stays on the boot screen...
What can be done to fix this? As I failed to make a backup of my original 4.3 firmware...
Thanks Again!
Click to expand...
Click to collapse
Did u use correct ROM for 4.3? Did u tried flash stock rom again?
hhai2pth said:
Did u use correct ROM for 4.3? Did u tried flash stock rom again?
Click to expand...
Click to collapse
I can't find the 4.3 firmare... Only the 4.4.2 firmare...
I just realized I may have to flash with O2's stock firmare as it is an O2 device...
MrGovernor said:
Hello, I am MrGovernor.
I have recently purchased a Galaxy Note 3 N9005 and decided to root it earlier today. The device is running on 4.3 because my carrier decide to delay their releases (O2).
About 2 hours ago I then decided to put a custom recovery on it before installing Omega ROM...
Now, me being a newb, I was following about 3 different tutorials at once; I managed to get to the final stage of using ODIN to flash CWM onto the phone (n9005-cwm-recovery-6.0.4.7-kk). Now, I did this and when my phone rebooted it got the initial loading screen and this message appeared:
This happens when I go into Recovery Mode and when I boot normally. I can still go into download mode.
I am a newb, have I bricked my new phone or is there any way to salvage it?
Thanks a load!
MrGovernor.
Click to expand...
Click to collapse
oh man...
You are running 4.3, but you flash cwm for KK (4.4.2) ?
You should flash cwm for 4.3 instead.
Try to find the stock firmware, and reflash it.
Cheers!
---------- Post added at 05:29 PM ---------- Previous post was at 05:26 PM ----------
MrGovernor said:
Now... Another issue...
I installed PhilZ Touch Recovery and that has worked fine...
However, I went full retard and 'Wiped System for a New ROM' before I made a backup...
I then tried to flash FoxHound ROM, I managed to get through the install process flawlessly, BUT, when the device rebooted it stays on the boot screen...
What can be done to fix this? As I failed to make a backup of my original 4.3 firmware...
Thanks Again!
Click to expand...
Click to collapse
if you have installed the ROM flawlessly and stuck at the boot screen, try go into recovery again and make a full wipe (but not the wipe for new rom). Then reboot.
But the custom ROM you are flashing is 4.3 also right ?
Because very simple, if you were on stock 4.3, and you flash custom ROM 4.4.2 without update your bootloader first to 4.4.2, the custom ROM won't run.
---------- Post added at 05:31 PM ---------- Previous post was at 05:29 PM ----------
MrGovernor said:
I can't find the 4.3 firmare... Only the 4.4.2 firmare...
I just realized I may have to flash with O2's stock firmare as it is an O2 device...
Click to expand...
Click to collapse
if your device N9005, you may use any other firmware so long as for N9005.
You can try to flash 4.4.2, but you have to tick "update bootloader" at ODIN. Please note, once you are on 4.4.2, you are not able to go back to 4.3, due to different bootloader.
antique_sonic said:
oh man...
You are running 4.3, but you flash cwm for KK (4.4.2) ?
You should flash cwm for 4.3 instead.
Try to find the stock firmware, and reflash it.
Cheers!
---------- Post added at 05:29 PM ---------- Previous post was at 05:26 PM ----------
if you have installed the ROM flawlessly and stuck at the boot screen, try go into recovery again and make a full wipe (but not the wipe for new rom). Then reboot.
But the custom ROM you are flashing is 4.3 also right ?
Because very simple, if you were on stock 4.3, and you flash custom ROM 4.4.2 without update your bootloader first to 4.4.2, the custom ROM won't run.
---------- Post added at 05:31 PM ---------- Previous post was at 05:29 PM ----------
if your device N9005, you may use any other firmware so long as for N9005.
You can try to flash 4.4.2, but you have to tick "update bootloader" at ODIN. Please note, once you are on 4.4.2, you are not able to go back to 4.3, due to different bootloader.
Click to expand...
Click to collapse
That's cleared a load up! I'll install the 4.3 firmware and get back to you (Samsung's Firmware Download Servers are incredibly slow <,<)
yeah. good luck
Thanks for all the help!
I used ODIN to flash this file:
N9005XXUENB4_N9005O2UENB1_N9005XXUENB1_HOME.tar.md5
From SamMobile's Firmware.
It's all working now, and it on the 4.4.2 KitKat Built.
Does this mean the bootload has updated and I can install the 4.4 Omega ROM?
This time I will make a restore point on PhilZ Custom Recovery!
MrGovernor said:
Thanks for all the help!
I used ODIN to flash this file:
N9005XXUENB4_N9005O2UENB1_N9005XXUENB1_HOME.tar.md5
From SamMobile's Firmware.
It's all working now, and it on the 4.4.2 KitKat Built.
Does this mean the bootload has updated and I can install the 4.4 Omega ROM?
This time I will make a restore point on PhilZ Custom Recovery!
Click to expand...
Click to collapse
when you flash it, u did tick the update bootloader right ?
If yes, means you are now on the 4.4.2 bootloader, and you can install the 4.4 custom ROM (but please read the respective thread on how to flash that custom ROM of your choice)
And when you want to flash Philz CWM, do choose the one for 4.4.2. Try to use the latest one.
Good luck!
antique_sonic said:
when you flash it, u did tick the update bootloader right ?
If yes, means you are now on the 4.4.2 bootloader, and you can install the 4.4 custom ROM (but please read the respective thread on how to flash that custom ROM of your choice)
And when you want to flash Philz CWM, do choose the one for 4.4.2. Try to use the latest one.
Good luck!
Click to expand...
Click to collapse
Thanks!
But... On last problem...
I've downloaded and used ODIN to install PhillZ Recovery ("philz_touch_6.08.9-hltexx.tar.md5").
It passes in ODIN, and boots straight to android.
However, when I try to boot into recovery mode, I get the normal 3 lines of text, but after a few seconds it reboots back to android...
What do?
P.S: I tried holding down all 3 buttons through the whole process (that just reboots), holding down only the Home and Volume + buttons once the text appears (still reboots)... I've also tried to Re-Flash the same version twice.
I just want to make a backup for this ROM in-case I f*ck up with other ROMs. Sorry for being such a scrub!
------NOTE----------
Installed Latest Version of PhillZ, all works A-OK!
MrGovernor said:
Thanks!
But... On last problem...
I've downloaded and used ODIN to install PhillZ Recovery ("philz_touch_6.08.9-hltexx.tar.md5").
It passes in ODIN, and boots straight to android.
However, when I try to boot into recovery mode, I get the normal 3 lines of text, but after a few seconds it reboots back to android...
What do?
P.S: I tried holding down all 3 buttons through the whole process (that just reboots), holding down only the Home and Volume + buttons once the text appears (still reboots)... I've also tried to Re-Flash the same version twice.
I just want to make a backup for this ROM in-case I f*ck up with other ROMs. Sorry for being such a scrub!
------NOTE----------
Installed Latest Version of PhillZ, all works A-OK!
Click to expand...
Click to collapse
Sorry was bit busy.
But if you do read my last post... I did mentioned you have to use the latest one better
Cheers, mate!
btw :
why do you like to use KK recovery on 4.3, and when you are on KK, you use 4.3 recovery ?
Set warranty bit is different than set warranty kernel
jerryspring said:
Set warranty bit is different than set warranty kernel
Click to expand...
Click to collapse
And what exactly is the point of posting this in a 4.5 years old thread ?
Dejan Sathanas said:
And what exactly is the point of posting this in a 4.5 years old thread ?
Click to expand...
Click to collapse
Cuz I asked a question and no one answered me. What would be causing the bootloop on my phone? With stock and custom ROMs, it is bootlooping in and out of recovery and saying set warranty bit recovery ...
But no user has to answer you .
Post and if somebody sees it and has the answer they will .
But on the Q&A board as very few read it now and a day is not long enough.
JJEgan said:
But no user has to answer you .
Post and if somebody sees it and has the answer they will .
But on the Q&A board as very few read it now and a day is not long enough.
Click to expand...
Click to collapse
The o.p is different than my question! So, instead of making a duplicate thread with basically same issue, I posted in here.
Hi,
I have rooted and installed TWRP on my 910F Note4 as I was fed up waiting on the lollipop update rolling out. I am currently on 4.4.4 and have made a full backup using TWRP of the stock rom.
My intention was flashing the Cyanogen ROM and using that, but i now see on sammobile there is a stock 5.01 rom available. I have a few questions about this.
1. If I flash to Cyanogen can I still revert back to the stock rom 4.4.4 I have made a backup with? I read somewhere there might be problems as I was on KitKat then moved to lollipop(Cyanogen).
2. Can I flash the stock lollipop rom from within TWRP? Or do you have to do this via ODIN?
3. If I flash the Lollipop stock ROM with Odin I assume I will lose root and TWRP? So this would have to done again?
Guess I am asking what is the best way to proceed?
Thanks again
Paul
pmlfrew said:
Hi,
I have rooted and installed TWRP on my 910F Note4 as I was fed up waiting on the lollipop update rolling out. I am currently on 4.4.4 and have made a full backup using TWRP of the stock rom.
My intention was flashing the Cyanogen ROM and using that, but i now see on sammobile there is a stock 5.01 rom available. I have a few questions about this.
1. If I flash to Cyanogen can I still revert back to the stock rom 4.4.4 I have made a backup with? I read somewhere there might be problems as I was on KitKat then moved to lollipop(Cyanogen).
2. Can I flash the stock lollipop rom from within TWRP? Or do you have to do this via ODIN?
3. If I flash the Lollipop stock ROM with Odin I assume I will lose root and TWRP? So this would have to done again?
Guess I am asking what is the best way to proceed?
Thanks again
Paul
Click to expand...
Click to collapse
hi Paul,
1. i beleve to flash CM from kitkat you will need to install the lollipop bootloader first.
2. You have to flash the stock rom via Odin, you will keep all apps settings and files but you will lose root (you u can re root in 3 minutes)
Best thing you could do is flash the stock rom first with odin, see how that feels (IMO its good been using it for months now) and then root it and back it up and flash CM12 (you dont have to flash any boatloader at this point)
grtz
Luc
Racinghart91 said:
hi Paul,
1. i beleve to flash CM from kitkat you will need to install the lollipop bootloader first.
2. You have to flash the stock rom via Odin, you will keep all apps settings and files but you will lose root (you u can re root in 3 minutes)
Best thing you could do is flash the stock rom first with odin, see how that feels (IMO its good been using it for months now) and then root it and back it up and flash CM12 (you dont have to flash any boatloader at this point)
grtz
Luc
Click to expand...
Click to collapse
Thanks will flash to lollipop today then....
pmlfrew said:
Thanks will flash to lollipop today then....
Click to expand...
Click to collapse
Ok tried to flash Stock O2 UK lollipop ROM via ODIN and got error message on screen. MD5 too big or something. Had to pull battery on phone. Had to then reflash TWRP. Got back into TWRP and tried to do a recovery of the backup I took but phone is stuck at Galaxy note 4 screen. It then shuts down and restarts and gets to the same screen again.
Do I try a different ROM? What can I do?
Thanks
Paul
pmlfrew said:
Ok tried to flash Stock O2 UK lollipop ROM via ODIN and got error message on screen. MD5 too big or something. Had to pull battery on phone. Had to then reflash TWRP. Got back into TWRP and tried to do a recovery of the backup I took but phone is stuck at Galaxy note 4 screen. It then shuts down and restarts and gets to the same screen again.
Do I try a different ROM? What can I do?
Thanks
Paul
Click to expand...
Click to collapse
I got it working by flashing the German non branded ROM... Got the error message again but then used a "All samsung recovery.tar" as stated on another post in here and it booted fine eventually... Now on Lollipop. Now time to flash with TWRP.... Again!!!
Please, i need help !
I need help, urgently !
My Note 4 SM-N910C does not work. I can enter the Recovery and the Download Mode. When attempting to install a Custom ROM gives me an error that says I have no data. In the internal memory I have 0mb.
I tried using odin, but I can not .. Salta error.
Someone who can make a backup of your phone (which is factory), leave me a link to download it? So I install the TWRP. Please.
They have another solution?
Thank you.:good:
Guys i have 910F...Running ANK4 KITKAT. I tried to root it with CF-Auto-Root-trlte-trltexx-smn910f. The rooting tutorial said i had to disable auto reboot and should perform a battery pullout after rooting....everything went fine untill i pulled out the battery and put it back in after root...the phone turns on and says "RECOVERY IS NOT SEANDROID ENFORCING" And just restarts...i am stuck in a bootloop whenver i try to root it.....i was able to get the phone back online after flashing stock 4.4.4 in ODIN, but what am i doing wrong here....why cant i root this phone?
This happened to me yesterday - you cannot root a stock rom v5.1.1 with CF Auto Root, if you try it will end up in a bootloop. There is a way around this if you search the Note 4 CF Auto Root thread - pages 121 and 124 if i remember rightly.
But i am not on 5.1 i am on stock 4.4.4....anyone else might wana help?
dork997 said:
But i am not on 5.1 i am on stock 4.4.4....anyone else might wana help?
Click to expand...
Click to collapse
4.4.4 what the hell is that?
If you try gingerbread, you will never update a rom. The best android on earth. (just after the eclair, froyo was a major disappointment)
dork997 said:
Guys i have 910F...Running ANK4 KITKAT. I tried to root it with CF-Auto-Root-trlte-trltexx-smn910f. The rooting tutorial said i had to disable auto reboot and should perform a battery pullout after rooting....everything went fine untill i pulled out the battery and put it back in after root...the phone turns on and says "RECOVERY IS NOT SEANDROID ENFORCING" And just restarts...i am stuck in a bootloop whenver i try to root it.....i was able to get the phone back online after flashing stock 4.4.4 in ODIN, but what am i doing wrong here....why cant i root this phone?
Click to expand...
Click to collapse
Are you trying to keep a stock ROM and root it?
I would upgrade to lolipop. I run AICP on my n910f and I love it, best ROM for our phone at the moment in my opinion. To go to a custom lolipop from kitkat you'll need to first flash a lolipop stock ROM, here Then you can flash your custom recovery via odin. Then you can flash any custom ROM via zip file from your recovery software as usual. Custom ROMs are usually rooted by default already so once you've flashed it you're already rooted. If you search the forum you can find a rooted stock ROM if that is your preference.
guts100 said:
Are you trying to keep a stock ROM and root it?
I would upgrade to lolipop. I run AICP on my n910f and I love it, best ROM for our phone at the moment in my opinion. To go to a custom lolipop from kitkat you'll need to first flash a lolipop stock ROM, here Then you can flash your custom recovery via odin. Then you can flash any custom ROM via zip file from your recovery software as usual. Custom ROMs are usually rooted by default already so once you've flashed it you're already rooted. If you search the forum you can find a rooted stock ROM if that is your preference.
Click to expand...
Click to collapse
stock 4.4.4 rom
dork997 said:
stock 4.4.4 rom
Click to expand...
Click to collapse
Did you try a factory data reset after using autoroot? Go into the stock recovery and do a factory data reset after auto root and it may boot after that. If you want to keep 4.4.4 stock ROM then just flash an already rooted stock ROM. They're in the ROM section for your device. That's what I would do if you're having issues with cf auto root.
I rooted my SM-G7102 using KingoRoot App for Windows.
Later I installed Twrp recovery using Odin 3.10.7 :http://forum.xda-developers.com/galaxy-grand-2/orig-development/twrp-unofficial-twrp-recovery-t2798433
Booted into recovery, did a factory reset and tried installing Resurrection Remix: http://forum.xda-developers.com/galaxy-grand-2/orig-development/rom-resurrection-remix-m-v5-6-7-t3360391
It installed successfully I latter install 6.0 micro gapps as advised on the ROM's Page and rebooted however it just showed me Sammy BootLogo and then a blue screen and then restarted again
I later did a complete format including /data and also tried installing CM13 unofficial: http://forum.xda-developers.com/galaxy-grand-2/orig-development/cm-13-0-ms013g-cyanogenmod-13-grand-2-t3299635
however same results.
Another alter I tried was installing both ROMs mentioned above without GAPPS however it didn't work too!
Would love to recieve some help, Thanks.
[EDIT]
p.s: I was using Samsung's Stock Andorid v4.3 firmware before flashing.
Also here is my recovery log: https://gist.githubusercontent.com/ArchKudo/ab4738a2482121fde280643fc86b5ab6/raw/0cae8a800552fc331d841bd1a6798c9a41e524ec/recovery.log
[EDIT 2]
It worked! Installed 4.4.2 and re-flashed
Flash 4.4.2 firmware
Then flash custom roms
Igor2906 said:
Flash 4.4.2 firmware
Then flash custom roms
Click to expand...
Click to collapse
Thanks for the reply!
Should I use the same TWRP recovery as mentioned before?
Also is 4.3 known to cause bootloops or is there some guesswork involved?
noobno.NaN said:
Thanks for the reply!
Should I use the same TWRP recovery as mentioned before?
Also is 4.3 known to cause bootloops or is there some guesswork involved?
Click to expand...
Click to collapse
Yeah use TWRP
me2 facing same problrm but i have first install from official 4.4.2 firmeware plz help
Hi all. I'm in need of the stock recovery file for N910H on stock 6.0.1. Preferably in .tar format. Thanks
d_myke said:
Hi all. I'm in need of the stock recovery file for N910H on stock 6.0.1. Preferably in .tar format. Thanks
Click to expand...
Click to collapse
I believe that sammobile would have the stock rom, which if i remember correctly will automaticly flash stock recovery on flash.
But what problem do you have or why do you need a stock recovery, if i may ask ?
Diload said:
I believe that sammobile would have the stock rom, which if i remember correctly will automaticly flash stock recovery on flash.
But what problem do you have or why do you need a stock recovery, if i may ask ?
Click to expand...
Click to collapse
Flashed TWRP on my unrooted phone via Odin. Worked the first time round, and I was able to clear cache. Rebooted, and I've not been able to boot into recovery since. I can boot into download mode, but not recovery mode. Pressing the right buttons just boots up the phone normally. Haven't got root, so I can't use an app to boot into recovery.
d_myke said:
Flashed TWRP on my unrooted phone via Odin. Worked the first time round, and I was able to clear cache. Rebooted, and I've not been able to boot into recovery since. I can boot into download mode, but not recovery mode. Pressing the right buttons just boots up the phone normally. Haven't got root, so I can't use an app to boot into recovery.
Click to expand...
Click to collapse
Are you absolutely sure that you flashed the right version? I did the wrong version once since the website van be a bit confusing for some phones, a reflash with the right one with Odin saved me
I want to root my phone but it needs to install a custom recovery, if ever I want to get back the stock recovery...
Does flashing the stock rom replace the custom recovery with the stock recovery?
Sorry I'm a noob
Hi there
I didn't got everything but I'll try to help.
Get latest Odin : https://samsungodin.com/download/Odin3_v3.12.3.zip
Get a stock ROM: chose the right one for you
http://samsung-updates.com/device/?id=SM-n910h
or
https://samsung-firmware.org/model/SM-N910H/
or
https://www.sammobile.com/firmwares/galaxy-note4/SM-N910H/
Get TWRP: https://eu.dl.twrp.me/treltexx/twrp-3.1.1-0-treltexx.img.tar.html
Get Magisk:
https://dl.xda-developers.com/4/4/2....zip?key=ZHiP_JZ9z3O4YQoq9ammlg&ts=1522485842
Flash stock ROM.
Flash TWRP. (Knox 0x1)
Boot to recovery and backup.
Flash Magisk in TWRP.
You'll end up with a rooted stock ROM and custom recovery
Hope this may help
Sent from my SM-N910F using XDA Labs
---------- Post added at 09:53 AM ---------- Previous post was at 09:50 AM ----------
zianfromPH said:
I want to root my phone but it needs to install a custom recovery, if ever I want to get back the stock recovery...
Does flashing the stock rom replace the custom recovery with the stock recovery?
Sorry I'm a noob
Click to expand...
Click to collapse
The short answer is YES.
Sent from my SM-N910F using XDA Labs
Thanks sir barlu
Another question, does flashing the stock rom ALONE make my phone stable and usable like a new one?
My phone is Note Edge SC-01G btw
I really wanted this phone to be rooted
zianfromPH said:
Thanks sir barlu
Another question, does flashing the stock rom ALONE make my phone stable and usable like a new one?
My phone is Note Edge SC-01G btw
I really wanted this phone to be rooted
Click to expand...
Click to collapse
Take care to get the right ROM or you could brick your phone! All I said above apply to N910H ONLY!
For your device: www.sammobile.com/firmwares/galaxy-note-edge/SC-01G/
Maybe another ROM would fit but you have to find out in the other threads...
Sorry if I can't help you more but there are too many differents versions
Sent from my SM-N910F using XDA Labs
Thank you sir