Related
Posted this in the UPGRADING section but it may be better suited here, I'm not completely sure.
So I think I just bricked my dads vogue.
I followed the instructions in the HOW TO FLASH YOUR VOGUE thread as best as I could and now I'm in a rough position. He's been ranting about the WinMo OS almost since he got it and wanted to try Android so I tried to flash it.
What's going on:
Blank (black) screen
Backlight is on
Orange status(?) LED
Unresponsive to anything
Powering up yields a green status LED, one buzz of the vibration, call & end keys light up then it reverts to the above. Takes 1 or 2 seconds.
Plugging in the USB gives me "Found New Hardware: Data Interface" but I don't have the drivers or w/e is required to install it.
Any one able to help me? I figured this should be pretty straight forward but it's turning out to be a nightmare. :cries:
After you flash the android rom, you have to load a system image and data image into it. That may be normal.
Note, I have not flashed mine to Android, but it seemslike your missing the next step in the process.
This may help...
The bottom may help with the bricking and the top may help with android.
http://forum.xda-developers.com/showthread.php?t=603508
nope it isnt bricked just reflash windows and use android via haret...sounds kernel related
With advice from the other thread I'm in bootloader(?) mode
But that's as far as I got.
oh man I'm in trouble said:
So I've gotten back to red/green/blue/white striped screen but nothing will read the phone/let me flash anything to it.
Screen says:
VOGU100 MFG
SPL-2.31.CoKe
CPLD-3
USB
Click to expand...
Click to collapse
oh man I'm in trouble said:
With advice from the other thread I'm in bootloader(?) mode
But that's as far as I got.
Click to expand...
Click to collapse
Did you download your ROM you needed?
staud8469 said:
Did you download your ROM you needed?
Click to expand...
Click to collapse
What carrier do you use?
Yes, downloaded the stock rom.
Provider is Verizon
oh man I'm in trouble said:
Yes, downloaded the stock rom.
Provider is Verizon
Click to expand...
Click to collapse
Ok then...you will need to flash another rom. Verizon, is a pain.
Here is NFSFANS ROM windows 6.5
http://forum.xda-developers.com/showthread.php?t=432487
The files from this forum will contain a program called ROMUpdateUtility. Run that in boot mode. Then run NFSFANS verizon provisioning. all files are on that forum. Just remember...Your device is not bricked (as it sounds). You could brick it though. So be careful. You may wanna get advice from a Verizon User.
staud8469 said:
The files from this forum will contain a program called ROMUpdateUtility. Run that in boot mode. Then run NFSFANS verizon provisioning. all files are on that forum.
Click to expand...
Click to collapse
At this point, I'm throwing everything I think I know or understand out the window.
That said, can you walk me through the process starting at the bootload screen?
oh man I'm in trouble said:
At this point, I'm throwing everything I think I know or understand out the window.
That said, can you walk me through the process starting at the bootload screen?
Click to expand...
Click to collapse
Yes, from a Sprint stand point though.
-download NFSFANS ROM
-Extract all the files from NFSFANS ROM to a new folder.
-Enter BootLoader
-Once it loads up plug your phone into your computer
-In your new folder there should be like 10 files...one of which say ROMUpdateUtility. Click and run that.
-Follow all the instructions on it.
-When it finishes...your phone will auto reboot.
-Once loaded up, Download Verizons Provesioning from NFSFANS ROM (you will find the link of the download towards the bottom of the first post NFSFAN has posted)
-Connect your phone to ur pc and put the Verizon Provesioning Cab on your sd card and install it.
-Restart your phone.
That should work.
Thanks a ton, I'm 35% into the RUU.
I'll keep everyone updated.
oh man I'm in trouble said:
Thanks a ton, I'm 35% into the RUU.
I'll keep everyone updated.
Click to expand...
Click to collapse
Thats good progress. Now if/and when your phone boots up. Tell me if it gets stuck...and where at. If not then your good
Seems to be stuck at the Verizon logo. (First screen upon startup.)
EDIT:
Yeah, it's stuck.
oh man I'm in trouble said:
Seems to be stuck at the Verizon logo. (First screen upon startup.)
Click to expand...
Click to collapse
Does it say No radio?
oh man I'm in trouble said:
Seems to be stuck at the Verizon logo. (First screen upon startup.)
Click to expand...
Click to collapse
give it awhile to boot though.
staud8469 said:
Does it say No radio?
Click to expand...
Click to collapse
Nope.
M 03 PACAAAM4070
B 01 R 1.06.30
D3NFS
^That appears briefly under the Verizon logo which is normal but it still hangs after it disappears.
staud8469 said:
give it awhile to boot though.
Click to expand...
Click to collapse
5-8 minutes isn't enough?
oh man I'm in trouble said:
Nope.
M 03 PACAAAM4070
B 01 R 1.06.30
D3NFS
^That appears briefly under the Verizon logo which is normal but it still hangs after it disappears.
5-8 minutes isn't enough?
Click to expand...
Click to collapse
Well, I'm going to get a verizon guy to help you. Brb.
ok sounds no radio has been written
follow this wiki to the T and you my friend will have a working phone with GPS
mainly a working phone!!!
http://wiki.ppchaven.com/index.php?title=Pocket_PC_WIki:FIX_VERIZON_GPS
How do you keep customization from running?
Hi there,
I am pretty new with this stuff, as I just got this phone today. It came with Froyo2.2 so I unrooted it back to the original JFK.
It did not come with a sim card, so I do not have a sim inside the phone as of now. But I do have a bell sim that I will use after to put the unlock key in... Is that okay?
I Connected the vibrant through Mini Kies and the MTP application says its connected.
I just re rooted from J16 back to the original.
I have the 64 bit drivers installed.
When I try to run Generate Unlock Windows Script I get the following error message saying...
Copy nv_data.bin
*daemon not running. Starting it now *
*daemon started succesfully *
error: device not found
error unable to find file <.\nv_data.bin>
could not find C:\documents and settings\1\desktop\key\generateunlockwindows\nv_data.bin
Anyone know what this means?
Or know what to do in this situation?
I am not sure if I should try installing the 32bit drivers or what.
how did you downgrade the phone from android 2.2?
I just bought the phone through ebay with the OS already at 2.2, and the phone is locked to t-mobile. I've heard it is not possible to unlock it with the 2.2 update. Is that true?
molson24 said:
Hi there,
I am pretty new with this stuff, as I just got this phone today. It came with Froyo2.2 so I unrooted it back to the original JFK.
It did not come with a sim card, so I do not have a sim inside the phone as of now. But I do have a bell sim that I will use after to put the unlock key in... Is that okay?
I Connected the vibrant through Mini Kies and the MTP application says its connected.
I just re rooted from J16 back to the original.
I have the 64 bit drivers installed.
When I try to run Generate Unlock Windows Script I get the following error message saying...
Copy nv_data.bin
*daemon not running. Starting it now *
*daemon started succesfully *
error: device not found
error unable to find file <.\nv_data.bin>
could not find C:\documents and settings\1\desktop\key\generateunlockwindows\nv_data.bin
Anyone know what this means?
Or know what to do in this situation?
I am not sure if I should try installing the 32bit drivers or what.
Click to expand...
Click to collapse
Yup, having exact same problem. If you find a fix let me know.
Make sure your usb setting is on debug and you have all of the files for the unlock on your pc. You also need java installed.
That method worked for me from stock.
can someone answer my question?
mbison83 said:
how did you downgrade the phone from android 2.2?
I just bought the phone through ebay with the OS already at 2.2, and the phone is locked to t-mobile. I've heard it is not possible to unlock it with the 2.2 update. Is that true?
Click to expand...
Click to collapse
I don't know whether the unlock methods work with Froyo but you can download a 2.1 stock Odin in the forum.
pvspencer22 said:
I don't know whether the unlock methods work with Froyo but you can download a 2.1 stock Odin in the forum.
Click to expand...
Click to collapse
where can i get it at and how do i do the rollback?
mbison83 said:
can someone answer my question?
Click to expand...
Click to collapse
...... please?
koooba said:
...... please?
Click to expand...
Click to collapse
very funny.
mbison83 said:
very funny.
Click to expand...
Click to collapse
Wasn't meant to be. Usually please and thanks goes a long way when asking for something. Shows appreciation.
^ Hence the THANKS button.
koooba said:
Wasn't meant to be. Usually please and thanks goes a long way when asking for something. Shows appreciation.
Click to expand...
Click to collapse
it also shows sarcasm and in this case thats what is seems like.
Read the stickies in the forum. If you can't figure it out ill grab the links tonight.
For the unlock this worked for me.
pvspencer22 said:
The windows tool worked for me from stock.
It doesn't generate a code though you input one.
Edit: link
http://forum.xda-developers.com/showthread.php?t=822008&page=11
Scroll down for instructions.
Click to expand...
Click to collapse
For going to stock. (From the general stickie)
draikz said:
Fixing so-called "Bricks"/Odin Errors
This guide is open to contribution/editing/correcting
-----------------------------------------------------------------------------------------------------
BOOT CYCLE
This is where you get the annoying Samsung Screen/Galaxy S screen.
DOWNLOAD REQUIRED (CREDITS TO JUSTANOTHERCROWD):
1. Get into Download Mode (WITH THE PHONE PLUGGED IN) by following the steps below
*Turn off the phone until you get to the charging battery screen (keep in mind, your phone is currently PLUGGED IN)
*Press volume up and down, and power all at once.
*As soon as the screen turns black, release your power button.
2. Unplug phone from USB
3. Open Odin (in Administrator if you're running W7 or Vista), try one of the ones I attached to this post, at least one of them is bound to work, some don't work for me, but works for others, some doesn't work for others, but works for me, whatever floats your boat
4. Load in the files into Odin that you have downloaded from above Just load in the files corresponding to the text field.
DO NOT CHECK REPARTITION.
5. Plug in your phone with the DL mode
6. Click start and wait for the magic
-----------------------------------------------------------------------------------------------------
NO-BOOT PHONES
This is where your phone does NOT turn on, no combo of buttons works and power button does nothing.
DO THIS ONLY WHEN YOU PLUG IN YOUR PHONE AND NOTHING SHOWS UP ON THE SCREEN!!! If else, follow the steps from above.
This method is basically same as above, EXCEPT the way you get into Download Mode as your phone is HARD BROKEN.
1. Download all the files required in the "BOOT CYCLE" section of this post.
2. Remove everything from your phone (SD card, sim, battery).
3. Plug your phone into your computer WITHOUT the battery, as you have already taken it out in the last step.
4. Press and HOLD vol. up and vol. down.
5. As you are HOLDING these buttons, reattach your battery.
6. You should be in Download Mode.
7. Unplug phone from USB
8. Follow steps 4-8 from the "BOOT CYCLE" section.
Troubleshooting:
-Odin stuck at some random process?
*Switch to another odin
*Make sure you did NOT check repartition, if you did, just repeat all the steps over again, except for the downloading parts, obviously.
-Phone not responsive?
*Try "NO-BOOT PHONES"section of this guide
-Phone stuck at Galaxy S logo screen?
*Put it in to DL mode, and run Odin again, it's just a bad install.
-All three ODIN is nonfunctional, stuck or giving "FAILED" errors?
*DO NOT CLOSE ODIN ONCE IT HAS FAILED!
*Unplug your phone
*Replug in your phone, get it into DL mode
* Unplug once it is in DL mode
*Replug and ODIN should recognize your phone
*Leave all the settings the same, then click "Start" again.
-Cannot get into download mode using the method I listed? Use the method(s) below:
Soldering Method
More methods coming soon
-----------------------------------------------------------------------------------------------------
I know how much of a pain posting in the Q/A section can be and the wait time is pretty bad, so if you need help regarding UNBRICKING and ONLY UNBRICKING feel free to post in here.[/S
Click to expand...
Click to collapse
I unlocked my phone w Galaxy_S unlock 2 days ago. It's in the market and I was running Bionix V when I did it.
draikz said:
^ Hence the THANKS button.
Click to expand...
Click to collapse
Pretty soon we'll have apps that'll say hi and thanks and apps in general will replace everything we say, so much for what our parents taught us huh?
koooba said:
Pretty soon we'll have apps that'll say hi and thanks and apps in general will replace everything we say, so much for what our parents taught us huh?
Click to expand...
Click to collapse
Technology > your parents.
Anyday.
Do you know any other way i could unlock my samsung vibriant .nothing on this site has worked for me,,,who do i pay get files to work on this site please help poor black boy
franjess said:
Do you know any other way i could unlock my samsung vibriant .nothing on this site has worked for me,,,who do i pay get files to work on this site please help poor black boy
Click to expand...
Click to collapse
Poor with a few hundred dollars worth of phone. Lol
Did you try the PRO SGS app?
franjess said:
Do you know any other way i could unlock my samsung vibriant .nothing on this site has worked for me,,,who do i pay get files to work on this site please help poor black boy
Click to expand...
Click to collapse
If you want help you are going to have to be a lot more specific. What have you actually tried?
Just a tip, people will not help you on these forums if you ask for help without showing you've tried to solve the problem and know how to search.
There are loads of unlock threads. Almost everyone get one method to work eventually.
So i was flashing the firmware to use the phone on the tab and while doing it the install failed. the tab cut off and will not come back on at all. no download mode nothing...anything can help. wont connect to odin either. any suggestions
Not come back on at all ?
Contact your service center then
Oh one thing...
When something like this happened, people call it "Bricked" not "Fu***d".
GOF007 said:
Not come back on at all ?
Contact your service center then
Oh one thing...
When something like this happened, people call it "Bricked" not "Fu***d".
Click to expand...
Click to collapse
lol i am fully aware of that just expressing how i feel about the brick and saying that it will not do anything..no download mode nothing.
thenewak said:
So i was flashing the firmware to use the phone on the tab and while doing it the install failed. the tab cut off and will not come back on at all. no download mode nothing...anything can help. wont connect to odin either. any suggestions
Click to expand...
Click to collapse
Do you get any lights whatsoever when it's plugged in?
Also, have you tried leaving it on charge for a while in the mains? Generally, when ODIN fails, the phone/tab allows you to get back into download mode, so this is new to me.
Was it flashing the radio (modem.bin) at the time, out of interest?
nprussell said:
Do you get any lights whatsoever when it's plugged in?
Also, have you tried leaving it on charge for a while in the mains? Generally, when ODIN fails, the phone/tab allows you to get back into download mode, so this is new to me.
Was it flashing the radio (modem.bin) at the time, out of interest?
Click to expand...
Click to collapse
No modem only the .tar and .pit files. i had flashed my galaxy s plenty of times with no problems. i left it charging tonight while im at work to see if that will do anything but i get no lights or anything. ive seen that some ppl get the pc to device screen but i dont get that either. but just wanted to try some things before shipping it to samsung only bc im in iraq and shipping takes forever.
Do U get anything when plugging the tab via USB to your computer ? And I do not mean Odin, I am just saying if the computer sees the USB connection.
Also, have you tried to press the POWER button and tap the screen at the same time ?
P_
pakalrtb said:
Do U get anything when plugging the tab via USB to your computer ? And I do not mean Odin, I am just saying if the computer sees the USB connection.
Also, have you tried to press the POWER button and tap the screen at the same time ?
P_
Click to expand...
Click to collapse
Nope the computer doesn't recognize it either. i get nothing at all..no i haven't tried that ...what exactly will that do?
If I bricked my Tab, I too would describe it as F***ED! But even with my moderate modding experience, Im not ready to do the phone mod. Just seems to me like too much risk.
Good luck with your Tab!
How is this a development issue? This isn't your personal support forum.
miketaylor00 said:
How is this a development issue? This isn't your personal support forum.
Click to expand...
Click to collapse
well i figured this would be an appropriate place to ask this type of ? as other ppl do. due to the fact that i was installing firmware from this section of the forums i figured i would ask the developers that read and write here.
anyways...i called samsung and told them idk why it wont cut on and they said to call it a power issue. so im going to send it to them to see if they can tell what i did..hopefully not. but we will see.
thenewak said:
well i figured this would be an appropriate place to ask this type of ? as other ppl do. due to the fact that i was installing firmware from this section of the forums i figured i would ask the developers that read and write here.
anyways...i called samsung and told them idk why it wont cut on and they said to call it a power issue. so im going to send it to them to see if they can tell what i did..hopefully not. but we will see.
Click to expand...
Click to collapse
Try leaving it connected to your computer for up to 1 hour with Odin loaded and ready on the screen.
Someone it will take time before it allow your PC to talk to it when it a messed up state due to a bad flash!
rmanaudio said:
Try leaving it connected to your computer for up to 1 hour with Odin loaded and ready on the screen.
Someone it will take time before it allow your PC to talk to it when it a messed up state due to a bad flash!
Click to expand...
Click to collapse
even if it will not power on at all?
thenewak said:
So i was flashing the firmware to use the phone on the tab and while doing it the install failed. the tab cut off and will not come back on at all. no download mode nothing...anything can help. wont connect to odin either. any suggestions
Click to expand...
Click to collapse
What were the names of the tar and pit files you flashed?
rotohammer said:
What were the names of the tar and pit files you flashed?
Click to expand...
Click to collapse
i dont see the thread on here but it was on here about a week ago. the first one that got you 3g + phone. Im not on my laptop bc im at work but do you know what im takling about.
Edit: i think it was the old JME and 512.pit...
OK just as an update and for anyone who had the same prob...as in tab will not do anything...i called samsung used the 1 yr warranty and told them it was a power issue...that i went to work it was on came home it was off and wouldnt power up so they replaced it with another one.
First off - i've searched all day & stayed in IRC for over 40 mins without a hit so i'm looking for a little help.
I was upgrading to Froyo from a "stock" Continuum today using Odin. Everything seemed smooth - got a pass message & unplugged the usb cable. Now nothing (won't power up, etc) & i can't get into download mode.
I've tried all of the button/cable/battery combos that i could find. I have tried to flash a recovery using Odin & it gets stuck with the message "setup connection" in the message box.
I know my pc is seeing the phone (though you can't access the SD card or memory) & Odin is seeing it (yellow box) but i can't seem to get past this point or go back to the original.
Any help is appreciated.
mountainmanscg said:
First off - i've searched all day & stayed in IRC for over 40 mins without a hit so i'm looking for a little help.
I was upgrading to Froyo from a "stock" Continuum today using Odin. Everything seemed smooth - got a pass message & unplugged the usb cable. Now nothing (won't power up, etc) & i can't get into download mode.
I've tried all of the button/cable/battery combos that i could find. I have tried to flash a recovery using Odin & it gets stuck with the message "setup connection" in the message box.
I know my pc is seeing the phone (though you can't access the SD card or memory) & Odin is seeing it (yellow box) but i can't seem to get past this point or go back to the original.
Any help is appreciated.
Click to expand...
Click to collapse
Try pulling your battery and holding down the power button for a slow count of 20 to see if download mode comes back. After that, you should be good to flash stock ec07 and then recovery kernel. After that, whichever rom you choose. If that doesn't work, I'll try to get into IRC at some point tomorrow (today).
That didn't work either - screen is still blank & it won't progress in Odin. I'll jump back into IRC if anyone has any other ideas - thanks.
i dont know what to tell you continuums are very hard to brick and if u cant get into download mode then theres not that much u can do im afraid I was talking to adam outler about trying the unbrickable mod on a continuum but he does not have one to test. now he got the fascinate to work so id pm him and see if he'll let you send your phone to him
Hey TXwolf - i had to run out for a while - saw where you got on IRC earlier. Verizon is sending me a new phone, so i guess i'll just give up on saving this one...
mountainmanscg said:
Hey TXwolf - i had to run out for a while - saw where you got on IRC earlier. Verizon is sending me a new phone, so i guess i'll just give up on saving this one...
Click to expand...
Click to collapse
I'll be in irc in a few if ya wanna give it another shot
I too manged to brick my phone to point to where I can not even get to the download screen. I have the same problem as OP, Odin will not move past SetupConnection when trying to recover following this post.
androidforums.com/continuum-all-things-root/457453-oh-crap-i-screwed-my-phone-up-recovery-guide.html
Any further help would much appreciated seeing as how I am past my warranty period and do not really want to buy a new phone.
PapaKaster said:
I too manged to brick my phone to point to where I can not even get to the download screen. I have the same problem as OP, Odin will not move past SetupConnection when trying to recover following this post.
androidforums.com/continuum-all-things-root/457453-oh-crap-i-screwed-my-phone-up-recovery-guide.html
Any further help would much appreciated seeing as how I am past my warranty period and do not really want to buy a new phone.
Click to expand...
Click to collapse
If this is frenzifun, from android forums, this is what happened to him
He started a flash of stock ec07 with pit and repartition checked. It flashed params.ifs, boot, SBL and recovery. Then it removed itself (frenzifun, if you could post the flash log for others it might help them) from there, it wont go into dl mode. I was trying to help him in irc, but I'm out of options, other than making a jig. The only thing I can think of, that's causing this is the somehow the button mappings for vol down got erased. I'm not sure how it would, though. Especially since it should be a hardware mapping, independent of any software. And if that is the case, I don't know how to fix it.
If this isn't frenzifun, disregard everything I just said.
Txwolf1980 said:
If this is frenzifun, from android forums, this is what happened to him
He started a flash of stock ec07 with pit and repartition checked. It flashed params.ifs, boot, SBL and recovery. Then it removed itself (frenzifun, if you could post the flash log for others it might help them) from there, it wont go into dl mode. I was trying to help him in irc, but I'm out of options, other than making a jig. The only thing I can think of, that's causing this is the somehow the button mappings for vol down got erased. I'm not sure how it would, though. Especially since it should be a hardware mapping, independent of any software. And if that is the case, I don't know how to fix it.
If this isn't frenzifun, disregard everything I just said.
Click to expand...
Click to collapse
I am not sure who frenzifun is but this still doesn't sound good for my situation. What I can tell you is I was following directions to try an update my phone from 2.1 to 2.2 using Odin. I believed the process was completed, not realizing it was not and unplugged my phone from the computer. From that point on I have not been able to turn the phone on or get the the download screen. Here is the odd thing if I plug the phone into my computer Windows recognizes and Odin can see a COM port but I still can not get past the setup connection when following the directions to try a recover my phone.
PapaKaster said:
I am not sure who frenzifun is but this still doesn't sound good for my situation. What I can tell you is I was following directions to try an update my phone from 2.1 to 2.2 using Odin. I believed the process was completed, not realizing it was not and unplugged my phone from the computer. From that point on I have not been able to turn the phone on or get the the download screen. Here is the odd thing if I plug the phone into my computer Windows recognizes and Odin can see a COM port but I still can not get past the setup connection when following the directions to try a recover my phone.
Click to expand...
Click to collapse
If that is the case, we might be able to do something. Can you meet me in irc at 830 central, tonight?
Txwolf1980 said:
If that is the case, we might be able to do something. Can you meet me in irc at 830 central, tonight?
Click to expand...
Click to collapse
Txwolf I do appreciate the offer and I am in PST and that would 630 my time but I need to take of a few things after and I am not sure I could make that time. One of my places to go is my local Verizon store to see if there anything they can do.
PapaKaster said:
Txwolf I do appreciate the offer and I am in PST and that would 630 my time but I need to take of a few things after and I am not sure I could make that time. One of my places to go is my local Verizon store to see if there anything they can do.
Click to expand...
Click to collapse
Unlessvyou have a hookup, i doubt verizon will help. What I was gonnavtry o garuntees here) is
1. Try flashing in odin with pit, but leavevrepartition unchecked. That most likely won't work, but it's a shot.
2. Use the heimdall version ofvthe guide. I think that may have a better chance. I'll hang out in irc for a while tonight. Just in case.
Txwolf1980 said:
Unlessvyou have a hookup, i doubt verizon will help. What I was gonnavtry o garuntees here) is
1. Try flashing in odin with pit, but leavevrepartition unchecked. That most likely won't work, but it's a shot.
2. Use the heimdall version ofvthe guide. I think that may have a better chance. I'll hang out in irc for a while tonight. Just in case.
Click to expand...
Click to collapse
I just got home but will again be leaving soon. I am sorry if you waited in IRC for me. You are right Verizon did nothing.
PapaKaster said:
I just got home but will again be leaving soon. I am sorry if you waited in IRC for me. You are right Verizon did nothing.
Click to expand...
Click to collapse
Its all good. Try the suggestions I gave you, when you have time. If they don't work, I'll have some down time tomorrow or sunday. Just let me know, and we'll see if we can make the schedules match
Hi guys, Ive searched and searched, but couldnt find anything that worked for me, so I apologize if this has been answered before.
I attempted to root my GS6 Sprint phone, and something has gone wrong. When the phone reboots the touch screen doesnt work at all and it doesnt find any cell signals.
I flashed to S6-UniKernel_v6-0001-ODIN, the firmware on the phone at the time was 5.1.1.
I tried to flash back using G920PVPU1AOCF_G920PSPT1AOCF_G920PVPU1AOCF_HOME.tar. but I get "FAILED" every time.
So I tried to install twrp-2.8.7.1-zeroflte.img, and that seemed to install fine, but I cant reset because even in TWRP I have no use of my touch screen.
I am using the samsung cable, and it does go to the Downloading mode, but as soon as I click start it fails.
Anyone that can help me fix this I would gladly paypal the cost of a six pack. (Mods if this isnt allowed please let me know)
Okay so here is what fixed it for anyone else like me that is a noob, and does dumb stuff to their phone. You cant roll back to old firmwares. You have to flash to the latest firmware that was on the phone or newer. I found the updated firmware and its good to go.
koop1955 said:
Minor correction. You can use the version that you started with or a later version. The only problems come if you try to use an earlier version, like going from 5.1.1 back to 5.0.2. Which won't work.
Here is the latest version available, should always work: https://www.androidfilehost.com/?fid=24269982087002159
Odin is available here: http://www.samsungodindownload.com/
Click to expand...
Click to collapse
Many thanks to koop1955 for his help, and thanks to everyone that jumped in to help a poor noob.
Demijinx said:
Hi guys, Ive searched and searched, but couldnt find anything that worked for me, so I apologize if this has been answered before.
I attempted to root my GS6 Sprint phone, and something has gone wrong. When the phone reboots the touch screen doesnt work at all and it doesnt find any cell signals.
I flashed to S6-UniKernel_v6-0001-ODIN, the firmware on the phone at the time was 5.1.1.
I tried to flash back using G920PVPU1AOCF_G920PSPT1AOCF_G920PVPU1AOCF_HOME.tar. but I get "FAILED" every time.
So I tried to install twrp-2.8.7.1-zeroflte.img, and that seemed to install fine, but I cant reset because even in TWRP I have no use of my touch screen.
I am using the samsung cable, and it does go to the Downloading mode, but as soon as I click start it fails.
Anyone that can help me fix this I would gladly paypal the cost of a six pack. (Mods if this isnt allowed please let me know)
Click to expand...
Click to collapse
Anybody? Literally ANY idea is worth a shot at this point.
Did you use Odin to root the device? What options did you set?
Zoolok said:
Did you use Odin to root the device? What options did you set?
Click to expand...
Click to collapse
Thanks for the reply Zooklok, I did use Odin, and I didnt change any settings.
So checked boxes under options are;
Auto Reboot
F. Reset Time
Thats all. I clicked "AP" to load the firmware, then clicked start.
Hello.. Assuming your phone is already rooted. Pls follow the below procedure
1. Restart and let the phone biot. Plug in your usb and insert a new for installation purpose
2. Hold and press power+up+home button to boot into recovery
3. Format and reflash the new rom
Should works like a charm
selferng said:
Hello.. Assuming your phone is already rooted. Pls follow the below procedure
1. Restart and let the phone biot. Plug in your usb and insert a new for installation purpose
2. Hold and press power+up+home button to boot into recovery
3. Format and reflash the new rom
Should works like a charm
Click to expand...
Click to collapse
Thanks for the feed back selferng, when I reboot into recovery, I cant select anything because the touch screen doesnt work
Demijinx said:
Thanks for the feed back selferng, when I reboot into recovery, I cant select anything because the touch screen doesnt work
Click to expand...
Click to collapse
Can u use the hardware button to select? Volume up and down and power button to select
selferng said:
Can u use the hardware button to select? Volume up and down and power button to select
Click to expand...
Click to collapse
Okay so I grabbed the lastest ODIN and was able to go back to the stock recovery. I performed a wipe/factory reset, but it still wont let me use the touch screen! ARG! It didnt clear the new kernel. Could it be because Im flashing to an older firmware? I cant find 5.1.1 anywhere...
Demijinx said:
Okay so I grabbed the lastest ODIN and was able to go back to the stock recovery. I performed a wipe/factory reset, but it still wont let me use the touch screen! ARG! It didnt clear the new kernel. Could it be because Im flashing to an older firmware? I cant find 5.1.1 anywhere...
Click to expand...
Click to collapse
Is the a Galaxy s6 or a S6 edge+ of edge+ you've been flashing the wrong firmwares, which would explain the issues you're having
Try a different cable or usb port or redownload the firmware file as it may be corrupted.
Press thanks if I helped.
You're on the wrong forum. This is for the Edge+. You have a S6. Not Edge, not +.
nms247 said:
Is the a Galaxy s6 or a S6 edge+ of edge+ you've been flashing the wrong firmwares, which would explain the issues you're having
Click to expand...
Click to collapse
Its the regular S6, not the edge. So the firmware is correct?
a. felon said:
Try a different cable or usb port or redownload the firmware file as it may be corrupted.
Press thanks if I helped.
Click to expand...
Click to collapse
I will trying downloading again. I have tried all my USB ports and the original cable and a brand new one.
B3311 said:
You're on the wrong forum. This is for the Edge+. You have a S6. Not Edge, not +.
Click to expand...
Click to collapse
Dang! Mods can we move this? Sorry guys.
Guys thanks for helping me out with this, all the responses are appreciated.
UPDATE! FIXED IT!
I tried a different root method
http://trueandroid.com/g920pvpu2bof...mware-sprint-galaxy-s6-sm-g920p-how-to-guide/
This worked the first time, and restored the touchscreen functions. Thank you everyone for your help.
Demijinx said:
Its the regular S6, not the edge. So the firmware is correct?
I will trying downloading again. I have tried all my USB ports and the original cable and a brand new one.
Dang! Mods can we move this? Sorry guys.
Guys thanks for helping me out with this, all the responses are appreciated.
Click to expand...
Click to collapse
Had to ask this being the edge+ forum
Sent from my SM-G928F using Tapatalk
Alright I spoke too soon. I got to my desktop once, now it just says:
Kernel Is not seadroin enforcing
Custom binary blocked by FRP lock.
Ugg. Lol I need help again.
Demijinx said:
Alright I spoke too soon. I got to my desktop once, now it just says:
Kernel Is not seadroin enforcing
Custom binary blocked by FRP lock.
Ugg. Lol I need help again.
Click to expand...
Click to collapse
Ok I know one thing for sure, you are not the first to face this but it seems to be solved by flashing the tar file for your device. More info here http://forum.xda-developers.com/sprint-galaxy-s6/help/custom-binary-blocked-frp-lock-t3152054
Good luck
Don't forget to Press that thanks button ?.
koop1955 said:
Minor correction. You can use the version that you started with or a later version. The only problems come if you try to use an earlier version, like going from 5.1.1 back to 5.0.2. Which won't work.
Here is the latest version available, should always work: https://www.androidfilehost.com/?fid=24269982087002159
Odin is available here: http://www.samsungodindownload.com/
Click to expand...
Click to collapse
koop1955 had the link. Koop, if you read this, hit me up with your paypal, I owe you some beer.
Demijinx said:
koop1955 had the link. Koop, if you read this, hit me up with your paypal, I owe you some beer.
Click to expand...
Click to collapse
Sorry, man, I won't accept it. I do this stuff for love and need to keep it pure.
But please Pay It Forward. Help somebody as you are able to.
koop1955 said:
Sorry, man, I won't accept it. I do this stuff for love and need to keep it pure.
But please Pay It Forward. Help somebody as you are able to.
Click to expand...
Click to collapse
Will do brother. Thank you so much, you really pulled me out of a spot. Im used to paying for everything in "Military Currency". Thank you again.