I have an Australian SM-N9005 that I want to upgrade to lollipop. I have done this a few other times without incidence on other Samsung phones but this one won't do it. There isn't any Australian 5.0 firmwares so I have tried the Taiwan and Hong Kong firmwares from SamMobile but I get this message every time
"<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> cache.img.ext4
<ID:0/003> FAIL! (Ext4)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)"
Can someone please help out with this, appreciated
have you the same problem by installing a custom rom?
belveder69 said:
I have an Australian SM-N9005 that I want to upgrade to lollipop. I have done this a few other times without incidence on other Samsung phones but this one won't do it. There isn't any Australian 5.0 firmwares so I have tried the Taiwan and Hong Kong firmwares from SamMobile but I get this message every time
"<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> cache.img.ext4
<ID:0/003> FAIL! (Ext4)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)"
Can someone please help out with this, appreciated
Click to expand...
Click to collapse
DONT TRY other countreys rom special assian...you will lose your imei.lolipop is not that good and everybody runs from it
If you have root acces you can try darklord s6 v3 is the best lolipop for note 3 n9005(you will void your warranty knox 0x1).
The rom is ported from s6 edge and is verry stable
Sent from my SM-A800F using XDA Free mobile app
I worked it out thanks, found the England firmware furthware further down the page.
Yes i could install custom roms but had no sounds and a few other buggy issues.
I disagree about not using foreign firmwares, i use Indian firmware on my Note 4, works just fine
belveder69 said:
I worked it out thanks, found the England firmware furthware further down the page.
Yes i could install custom roms but had no sounds and a few other buggy issues.
I disagree about not using foreign firmwares, i use Indian firmware on my Note 4, works just fine
Click to expand...
Click to collapse
Glade it works ... the ideea was that assian softwares are different for rest..the dark lord rom has no problems with sound ...give it a try.i have it and i dont have any problems
Cheers
Sent from my SM-A800F using XDA Free mobile app
Related
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
I tried to install stock Brazil 4.4.2, then my pit file was missing
Downloaded Stock 4.3 and tried again with pit file now i got auth failed
I ticked re-partition and im using CSB_signed_Fusion3_EUR_0325_V2
i dont know waht do anymore... pliz help
NotaHue said:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
I tried to install stock Brazil 4.4.2, then my pit file was missing
Downloaded Stock 4.3 and tried again with pit file now i got auth failed
I ticked re-partition and im using CSB_signed_Fusion3_EUR_0325_V2
i dont know waht do anymore... pliz help
Click to expand...
Click to collapse
You can no longer downgrade your phone to 4.3 after Flashing 4.4.2 firmware mate and and you might wanna Check this thread
but installation on 4.4.2 failed too so i need pit file for 4.4.2?
i was in 4.3 bootloader then i was trying to install 4.4.2 sotck but failed (missing pit file)
NotaHue said:
but installation on 4.4.2 failed too so i need pit file for 4.4.2?
i was in 4.3 bootloader then i was trying to install 4.4.2 sotck but failed (missing pit file)
Click to expand...
Click to collapse
Ask from this thread mate , Im sure Samersh or malybru can help you fix this situation . Have a nice day
When i try to install android with odin I reveive this error :
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> FAIL! (Size)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I can't go in recovery mode . When I power the phone i reveive :
Firmware upgrade encountered an issue . Please select recovery mode in Kies& try again
.
I tried also with kies .. but i don't finished this error . Sorry for my english .
Please , help me! Thank you!
read: http://forum.xda-developers.com/showthread.php?t=2906438
or
http://forum.xda-developers.com/showthread.php?t=3053957
or
http://forum.xda-developers.com/showthread.php?t=3053525
Firmware-update Samsung Galaxy S5plus G901FXXU1BOC4 (NEE) available
SM-G901F Galaxy S5 4G+ lollipop 5.0.2
Samsung galaxy S5 GS-G901F user thread.
im sure there are alot of topics like this but last time i tried a move like this i soft bricked my phone so i need help :/
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
this is the error i dont know whats wrong didnt use a pit file and i kinda dont want to disconnect my phone now last time i did that it got soft bricked i did everything in the unroot guide (noob friendly) btw. using odin 3.10.6,samsung s4 gt-i9505
its all good now used odin 3.9 i think the 3.10 was faulty,the post can be closed or deleted
Hello all,
So ill make this short and sweet, I have an S5 the G900F and it wont boot, it just turns on, shows the Galaxy S5 logo, then appears to start the next Samsung logo but crashes instantly and restarts (does this on a loop)
I have attempted to use odin and flash using the latest firmware I believe to be correct for the phone, to which it fails at the end on "complete write operation failed". I then proceeded to try the recovery.tar file from the same rom and it worked (took about 10 seconds total) but im still getting the same loop.
Tried Kies and all that jazz, literally doesn't even see the phone so cant do jack, recovery mode doesn't boot, all I can get is download mode (home+voldown+power)
I would be ever so grateful if someone knows the answer to this as its driving me insane.
p.s. im by no way good with android so if im missing something blatantly obvious shout it out.
Thanks in Advance
Where am I going wrong?
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> FAIL! (Ext4)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
itsenigma said:
Where am I going wrong?
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> FAIL! (Ext4)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Try this guide.
Or this little tutorial:
Open the firmware file in winrar and extract the hidden.img. Rename it as hidden.img.tar.
Load the new file into the PDA tab, and flash.
Click to expand...
Click to collapse
Hello everyone,
I bricked my phone…. It is a SM-J510FN and when I start it right now, it shows "An error has occured while updating the decive Software. etc." Smart Switch is not recognizing the decive anymore, I cannot enter TRWP and I tried to Flash the stock Rom with Odin but it fails with the following error :
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 2878 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> hyp.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I would highly appreciate any help since I am running out of ideas what to do....
Thanks in Advance!
ottavio22 said:
Hello everyone,
I bricked my phone…. It is a SM-J510FN and when I start it right now, it shows "An error has occured while updating the decive Software. etc." Smart Switch is not recognizing the decive anymore, I cannot enter TRWP and I tried to Flash the stock Rom with Odin but it fails with the following error :
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 2878 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> hyp.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I would highly appreciate any help since I am running out of ideas what to do....
Thanks in Advance!
Click to expand...
Click to collapse
Did you try flashing TWRP again? Bc you flash stock one! If you could enter twrp, flash some of ROMs for your device.
RootingPro-18 said:
Did you try flashing TWRP again? Bc you flash stock one! If you could enter twrp, flash some of ROMs for your device.
Click to expand...
Click to collapse
Thank you for your answer. I did try that but was unable to to boot into TWRP. I finally managed to Flash the stock ROM via Odin. The mistake I pointed out above was fixed by changing from a 3.0 USB to a 2.0 USB port. Weirdly Odin seems to create Errors when using 2.0 in some rare Occasion. For everyone encoutering the same I encourage you to check if you are using a 2.0 USB.
Thank you for the answer anyway. Thread can be closed.
ottavio22 said:
Thank you for your answer. I did try that but was unable to to boot into TWRP. I finally managed to Flash the stock ROM via Odin. The mistake I pointed out above was fixed by changing from a 3.0 USB to a 2.0 USB port. Weirdly Odin seems to create Errors when using 2.0 in some rare Occasion. For everyone encoutering the same I encourage you to check if you are using a 2.0 USB.
Thank you for the answer anyway. Thread can be closed.
Click to expand...
Click to collapse
i had no issues with 3.0