Related
The following steps should unbrick your Dell Venue pro in most cases (this will not unbrick your phone if you updated the touch screen firmware via the EM app). You can do this at your own risk. I strongly suggest calling or e-mailing Dell Mobility Support before doing this. If your phone is out of warranty, you replaced the SD card, or did something else really silly to it then this might be your only option. You will lose all data on your phone with this method. Your contacts should be backed up on Live/Hotmail/Facebook/Twitter/Etc. and your images on SkyDrive. Everything else will be wiped. You phone will be wiped back to Version 7704 (or what we had when the phone launched back in October of 2010).
The following instructions are for Windows-based machines. There might be a similar utility for Mac’s but I have no way to find out. You are on your own if you have a Mac.
Unplug your DVP, Remove the battery.
If you replaced your SD card (and voided the warranty in the process) please insert your stock SD card at this time. If you never touched your SD card then you can obviously skip this step.
If your phone already has the stock SD card in it, please wait 10 seconds, and put the battery back in. You may put the cover back on as well if you like.
Now we are going to enter the boot loader (this is how your bricked phone can receive the FFU file) by holding the volume down (-), camera, and then power buttons. DO NOT RELEASE THESE until you see the image of a phone, USB cable, and laptop.
Connect your Dell Venue Pro to your computer with the USB cable that came with the phone or one that has the same or higher specs. I have seen it take up to 10 minutes for the phone to be recognized by your computer. If after 10 minutes your phone hasn’t connected, try another USB port and/or cable.
While your computer is installing the drivers/connecting to your phone download the following file and extract it.
http://www.multiupload.com/5YT27EHLZV
VenuePro_flash_GLEOS2A_US_TMO_SIGNED_SWV0105_LP0030_RV001_RETAIL.zip (138.7 MB)
While this is downloading, close Zune if it is not already closed as it takes a few seconds for it to really unload from memory.
Once you think your phone has been connected, open up command prompt (you may need to start it in admin mode depending on your security settings) by typing “cmd” in the start menu or going start -> run and entering “cmd”.
Change directory to “C:\program files\zune\” by typing “cd C:\program files\zune\” and hitting enter
Then type “UpdateWp /list” and your phone should show up there. If it hasn’t be patient and read step 3 again.
If your phone is listed (it should be) and your download is done and extracted, copy the VenuePro_flash_GLEOS2A_US_TMO_SIGNED_SWV0105_LP0030_RV001_RETAIL.ffu file over to the” C:\program files\zune\” directory. You may wish to rename this file before copying it over to something shorter if you wish for the next part.
Now back in the command prompt window type “updatewp /ffu VenuePro_flash_GLEOS2A_US_TMO_SIGNED_SWV0105_LP0030_RV001_RETAIL.ffu”. If you did not rename the FFU file you can type Venue and then hit tab to auto complete the name otherwise enter the name of the FFU file you renamed.
Hit enter and DO NOT unplug the phone. This process can take anywhere between 60 seconds and 10 minutes.
This should work and bring you back to the stock state. If it does not you can retry this a few more times but if after 2 or 3 times it does not work then you need to contact Dell as your phone is royally screwed.
You can now re-open Zune, pair your device, and update all the way back to Mango (this could take up to an hour).
Now I wonder if there is a way to edit that ffu file ...
domineus said:
Now I wonder if there is a way to edit that ffu file ...
Click to expand...
Click to collapse
That would be nice
I have a question:
My phone told me:
So I tried many of my backup (first boot,Nodo and mango beta backup) to restore it and the ffu backup file but my phone boot in 20mins and no access to EM or any other application but I have an home screen...
Can you tell me if I try to replace my sd card and flash with the ffu i can retreive a working phone?
(Dell doesn't respond to my mails)
There are other threads already dedicated to replacing the sd card.
'Then type “UpdateWp /list” and your phone should show up there. If it hasn’t be patient and read step 3 again'
I tried entering that but it said 'updatewp /list' is not a recognized as an internal or external, operable program or batch file.' Is there something I'm doing wrong? I've tried it on two different laptops.
Please reply as soon as possible
then you dont have the updatewp tool installed...update your zune.
MJCS said:
then you dont have the updatewp tool installed...update your zune.
Click to expand...
Click to collapse
I have the latest zune and there's nothing to update. Is the updatewp tool a seperate program?
nevermind I found it, working
I am glad I could help
totoropororo said:
I have the latest zune and there's nothing to update. Is the updatewp tool a seperate program?
nevermind I found it, working
Click to expand...
Click to collapse
hey i have the same problem you had. please could you tell me where you found it?
asim2462 said:
hey i have the same problem you had. please could you tell me where you found it?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1262471
Here you go~!
The OP should make it clearer on the original post for newbies like us ._.
much appreciated. deserve my thanks!
Hello!
I replaced the broken screen on DVP. But now when you turn on DVP he says "Storage card not working".
I'm trying to apply the decision of the post, but if you type updatewp / list or updatewp / ffu ...... - I get an error message following items:
C: \ Program Files \ Zune> updatewp / list
UpdateWP version 4.8.2345.0
Error: System.IO.FileNotFoundException: Could not load file or assembly "In
terop.WM7UpdateLib, Version = 4.8.0.0, Culture = neutral, PublicKeyToken = null "or
din of its dependencies. Can not find the file specified.
File name: "Interop.WM7UpdateLib, Version = 4.8.0.0, Culture = neutral, PublicKeyTok
en = null "
in Microsoft.WindowsMobile.DeviceUpdate.DeviceManager.Initialize ()
in Microsoft.WindowsMobile.DeviceUpdate.DeviceManager.get_Instance ()
in wm7update.Program.Main (String [] args)
Warning: check assembly bind off.
To enable assembly bind failure logging, set the parameter value
registry [HKLM \ Software \ Microsoft \ Fusion! EnableLog] (DWORD) to 1.
Note. Registration assembly bind failure can lead to some reduction
NIJ performance.
To turn this feature off, remove the registry value [HKLM \ Software \ Microsoft \ F
usion! EnableLog].
C: \ Program Files \ Zune>
Please help!
Gorokhovsky said:
Hello!
I replaced the broken screen on DVP. But now when you turn on DVP he says "Storage card not working".
I'm trying to apply the decision of the post, but if you type updatewp / list or updatewp / ffu ...... - I get an error message following items:
C: \ Program Files \ Zune> updatewp / list
UpdateWP version 4.8.2345.0
Error: System.IO.FileNotFoundException: Could not load file or assembly "In
terop.WM7UpdateLib, Version = 4.8.0.0, Culture = neutral, PublicKeyToken = null "or
din of its dependencies. Can not find the file specified.
File name: "Interop.WM7UpdateLib, Version = 4.8.0.0, Culture = neutral, PublicKeyTok
en = null "
in Microsoft.WindowsMobile.DeviceUpdate.DeviceManager.Initialize ()
in Microsoft.WindowsMobile.DeviceUpdate.DeviceManager.get_Instance ()
in wm7update.Program.Main (String [] args)
Warning: check assembly bind off.
To enable assembly bind failure logging, set the parameter value
registry [HKLM \ Software \ Microsoft \ Fusion! EnableLog] (DWORD) to 1.
Note. Registration assembly bind failure can lead to some reduction
NIJ performance.
To turn this feature off, remove the registry value [HKLM \ Software \ Microsoft \ F
usion! EnableLog].
C: \ Program Files \ Zune>
Please help!
Click to expand...
Click to collapse
This arises from a previous installation of Windows Phone Support Tool. You have to uninstall it and then install/reinstall the file found in this link http://www.megaupload.com/?d=PL7H6FKJ) and then I copied the files in this link http://forum.xda-developers.com/showthread.php?t=1262471 to the Zune Directory.
Hopefully that solves your problem.
totoropororo said:
This arises from a previous installation of Windows Phone Support Tool. You have to uninstall it and then install/reinstall the file found in this link http://www.megaupload.com/?d=PL7H6FKJ) and then I copied the files in this link http://forum.xda-developers.com/showthread.php?t=1262471 to the Zune Directory.
Hopefully that solves your problem.
Click to expand...
Click to collapse
Thank YOU VERY MUCH!!!!
It's WORKED!!!
Here I took a Zune http://www.megaupload.com/?d=KY8J8SIY
Hello!
DVP restored, upgraded to the latest version. But phone does not see MicroSD HC 32Gb Class 10. Before that, everything worked fine. Now available in 32 Gb only 400 Mb: (
Put on the stock card 8Gb Class 4 - worked. But ...
Several times already rolling away in 7004, updated again - anyway, just out of 32Gb 400Mb ...
EM Test says SD Card - not installing, but the DVP should not run without the card!
Please, help me again...
DVP really work without a memory card But I do not need. So it does not work 32Gb ...
Seems Megaupload site has been taken down by the US Gov
Any other links for the Venu Flash File
Sorry guys, I can't seem to find another version of the first link I listed. I deleted mine unless someone can reupload it. The only suggestion I have is to try and check this link (http://www.multiupload.com/EQK2RPH3P6) file for the 'updatewp.exe', which should install 'Windows Phone Engineer Flashing Tool'. Why oh why did they shut down Megaupload, when it also had its legitimate reasons as well. But I can't blame them or agree with what those Pro-SOPA and PIPA are trying to do. There are always two sides to every story I suppose.
what was the name of the file you said that has to be uninstalled / reinstalled
Hi @all,
my sony minipro with ics4.04 (root),
seems to have an prob. with vpn.
when i try to use vpncilla it brings me an error that the vpn.api is not
installed,
Exception Error:
Unable to find activity class
{com.android.vpndialogs/com.android.vpndialogs.ConfirmDialog); have you declared this activity in your AndroidManifext.xml?
Error: the devices Android firmware seems to have an incomplete VPN API.
an similar error i get with the NCP Secure CLient.
Is it possible that sony removed some Api`s out of the stock ics FW?.
How can i check and fix it?
Greetings
mc_eddy
A friend has asked me to look at this Nokia Lumia 520, apparently it turned on one day and displayed this error message "unable to find a bootable option. Press any key to shutdown"
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Nokia Software Update for Retial recognises the phone and says software can be installed:
This downloads fine and starts the install process, however always fails with the message "phone not supported by nokia software updater retail"
I have also tried using NaviFirm+, searching for the product code 059S3T5 which lets me download the RM914_3058.50000.1425.0006_RETAIL_eu_euro1_327_06_452364_prd_signed firmware.
However i'm unable to flash this with the Nokia Care Suite, it states: 0xFA001106: Signature check of FFU file fails. Reason(s): The FFU file is not correctly signed or not signed for this device.
Has anyone got any suggestions on what else i can try to flash this firmware? or to try fix the phone?
I was following the tutorial here Flash/unbrand Lumia devices thinking if the firmware was re flashed all would be fine.
Cheers for any advice
Have you try with this
http://www.microsoft.com/en-us/mobile/support/faq/?action=singleTopic&topic=FA142987
Thanks for the suggestion, I have tried that, it will download the firmware too, however fail before flashing it stating the device is not supported.
InsaneNutter said:
Thanks for the suggestion, I have tried that, it will download the firmware too, however fail before flashing it stating the device is not supported.
Click to expand...
Click to collapse
I think win partition is crash. (like memory damage/corruption)
Hardware related problems.
InsaneNutter said:
A friend has asked me to look at this Nokia Lumia 520, apparently it turned on one day and displayed this error message "unable to find a bootable option. Press any key to shutdown"
Nokia Software Update for Retial recognises the phone and says software can be installed:
This downloads fine and starts the install process, however always fails with the message "phone not supported by nokia software updater retail"
I have also tried using NaviFirm+, searching for the product code 059S3T5 which lets me download the RM914_3058.50000.1425.0006_RETAIL_eu_euro1_327_06_452364_prd_signed firmware.
However i'm unable to flash this with the Nokia Care Suite, it states: 0xFA001106: Signature check of FFU file fails. Reason(s): The FFU file is not correctly signed or not signed for this device.
Has anyone got any suggestions on what else i can try to flash this firmware? or to try fix the phone?
I was following the tutorial here Flash/unbrand Lumia devices thinking if the firmware was re flashed all would be fine.
Cheers for any advice
Click to expand...
Click to collapse
Hi,
Have you sorted your phone out yet?
BruceKDallas said:
Hi,
Have you sorted your phone out yet?
Click to expand...
Click to collapse
Hi,
Nope i could never fix the phone, I spent loads of time messing about with it however think it was a hardware related problem.
I've given it back to my friend and shes since got a new phone.
I am into the same situation... NOKIA 520 RM-914 Code 059S7H0
"ERROR: Unable to find a bootable option. Press any key to shut down". Any button I push, the phone is going in bootloop ending with this ERROR...
I have tryed first with Windows Device Recovery Tool (WDRT) 3.1.4 to repair it, but no success...
In WDRT my Lumia is not detected automatically, so i must choose manually device manufacturer. To be detected I must restart the Lumia when DWRT is trying to detect it.
The Phone is detected as LUMIA phone, firmware version: unknown, Software available on server: 3058.50000.1425.003.
When I try to install the software after I download the package, the result is:
"Operation ended with failure. The software is not correctly signed or not signed for this device."
The NOKIA driver is seen as NOKIA BOOTMGR.
Then I've search on the internet about this problem and I've found this thread.
I tried the advanced mode with thor2.exe, I downloaded manually the firmware for my device Lumia 520, RM-914, Code 059S7H0
I opened Command Prompt as administrator, then used the command:
cd c:\Program Files (x86)\Microsoft Care Suite\Windows Device Recovery Tool\
I used the command line to extract gtp0.bin from ffu image:
thor2 -mode ffureader -ffufile "C:\rm-914\RM914_3058.50000.1425.0003_RETAIL_eu_hungary_422_03_447211_prd_signed.ffu"
The result was 2 files, gpt0.bin and GPT1.bin. I renamed gpt0.bin as msimage.mbn.
RKH of the device is:
RKH of SBL1: F771E62AF89994064F77CD3BC16829503BDF9A3D506D3FACECAEF3F808C868FD
RKH of UEFI: F771E62AF89994064F77CD3BC16829503BDF9A3D506D3FACECAEF3F808C868FD
I've downloaded the hex file for my Lumia RM-914 to have the 2 files HEX.hex and msimage.mbn for the command line:
thor2 -mode emergency -hexfile "C:\TEMP\HEX.hex" -mbnfile "C:\TEMP\msimage.mbn" -orig_gpt
THOR2 1.8.2.18
Built for Windows @ 13:36:46 Jun 16 2015
Thor2 is running on Windows of version 6.1
thor2 -mode emergency -hexfile C:\TEMP\HEX.hex -mbnfig_gpt
Process started Sun Dec 06 23:12:08 2015
Debugging enabled for emergency
Initiating emergency download
Operation took about 10.00 seconds.
THOR2_ERROR_CONNECTION_NOT_FOUND
THOR2 1.8.2.18 exited with error code 84000 (0x14820)
The Phone is still in NOKIA BOOTMGR mode...
If I try to disconnect the phone and restart, it goes into the the same message:
"ERROR: Unable to find a bootable option. Press any key to shut down", not showing me the RED screen like it should be.
If I go into the next step for flashing the device with the command line:
thor2.exe -mode vpl -maxtransfersizekb 1 -vplfile "C:\RM-914\RM914_059S7H0_3058.50000.1425.0003_037.vpl"
the screen changes into a big NOKIA logo, the driver goes from NOKIA BOOTMGR into NOKIA FLASH...
Thor2 is running on Windows of version 6.1
thor2.exe -mode vpl -maxtransfersizekb 1 -vplfile C:\RM-914\RM914_059S7H0_3058.5
0000.1425.0003_037.vpl
Process started Sun Dec 06 23:22:20 2015
Logging to file C:\Users\Marta\AppData\Local\Temp\thor2_win_20151206232220_Threa
dId-3864.log
Parsing VPL file C:\RM-914\RM914_059S7H0_3058.50000.1425.0003_037.vpl
Successfully parsed VPL
Flashing .ffu file RM914_3058.50000.1425.0003_RETAIL_eu_hungary_422_03_447211_pr
d_signed.ffu (SW version 3058.50000.1425.0003)
Debugging enabled for uefiflash
Initiating FFU flash operation
WinUSB in use.
isDeviceInNcsdMode
isDeviceInNcsdMode is false
Device mode 6 Uefi mode
[THOR2_flash_state] Pre-programming operations
Disable timeouts
Get flashing parameters
Lumia Boot Manager detected
Check status of battery
State of charge 8, charging current 282
Protocol version 1.1 Implementation version 1.16
Detecting UEFI responder
HELLO success
Lumia Boot Manager detected
Check status of battery
State of charge 8, charging current 266
Protocol version 1.1 Implementation version 1.16
Booting to FlashApp
Reboot to FlashApp command sent successfully.
DetachFrom connection
Verifying that device is online
Device is online
Detecting UEFI responder
HELLO success
Lumia Flash detected
Protocol version 1.15 Implementation version 1.28
Disable timeouts
Get flashing parameters
Lumia Flash detected
Protocol version 1.15 Implementation version 1.28
Size of one transfer is 2363392
Size of buffer is 2359296
Number of eMMC sectors: 15269888
Platform ID of device: Nokia.MSM8227.P6036.1.2
Async protocol version: 01
Security info:
Platform secure boot enabled
Secure FFU enabled
JTAG eFuse blown
RDC not found
Authentication not done
UEFI secure boot enabled
SHK enabled
Device supports FFU protocols: 0019
[THOR2_flash_state] Device programming started
Using secure flash method
CoreProgrammer version 2015.06.10.001.
Start programming signed ffu file C:\RM-914\RM914_3058.50000.1425.0003_RETAIL_eu
_hungary_422_03_447211_prd_signed.ffu
FfuReader version is 2015061501
Send FlashApp write parameter: 0x4d544f00
Perform handshake with UEFI...
Flash app: Protocol Version 1.15 Implementation Version 1.28
DevicePlatformInfo: Nokia.MSM8227.P6036.1.2
Unknown sub block detected. Skip...
Unknown sub block detected. Skip...
Supported protocol versions bitmap is 19
Secure FFU sync version 1 supported.
Secure FFU async version 1 supported.
Secure FFU async version 3 supported.
Get CID of the device...
Get EMMC size of the device...
Emmc size in sectors: 15269888
CID: Samsung, Size 7456 MB
Start charging...
Requested write param 0x43485247 is not supported by this flash app version.
Start charging... DONE. Status = 0
Unable to send ECHO REQ or ECHO REQ not supported
Get security Status...
Security Status:
Platform secure boot is enabled.
Secure eFUSE is enabled.
JTAG is disabled.
RDC is missing from the device.
Authentication is not done.
UEFI secure boot is enabled.
Secondary HW key exists.
Get RKH of the device...
RKH of the device is F771E62AF89994064F77CD3BC16829503BDF9A3D506D3FACECAEF3F808C
868FD
Get ISSW Version...
Get ISSW Version, SKIPPED!
Get system memory size...
Size of system mem: 524288 KB
Read antitheft status...
Requested read param 0x41545250 is not supported by this flash app version.
Send backup to RAM req...
Clearing the backup GPT...SKIPPED!
Successfully parsed FFU file. Header size: 0x000e0000, Payload size: 0x000000006
2900000, Chunk size: 0x00020000, Header offset: 0x00000000, Payload offset: 0x00
000000000e0000
RKH match between device and FFU file!
Option: Skip CRC32 check in use
Start sending header data...
FlashApp returned reported error in SecureFlashResp!
Status: 0x1106, Specifier: 0x8000000E
FA_ERR_FFU_SEC_HDR_VALIDATION_FAIL
Send of FFU header failed!
[IN] programSecureFfuFile. Closing C:\RM-914\RM914_3058.50000.1425.0003_RETAIL_e
u_hungary_422_03_447211_prd_signed.ffu
programming operation failed!
0xFA001106: Signature check of FFU file fails. Reason(s): The FFU file is not co
rrectly signed or not signed for this device.
Operation took about 3.00 seconds.
THOR2_ERROR_FA_SIGNATURE_FAIL
THOR2 1.8.2.18 exited with error code -100658938 (0xFA001106)
Here, after this step, if the flash is 100% succesful, the screen must change in Green,
mine finished with the same error: "The FFU file is not correctly signed or not signed for this device..."
I guess the most of us are into the same situation, I can't make the device to skip the signature check... Any sugestions?
have you jtag?
As far as I read, JTAG is a toolbox for repairing Phones which have the same problem, but what we are trying to do is without this toolbox, we have a dead phone at home. Microsoft said is a hardware failure and they must change complete motherboard, but with Jtag Toolbox can be repaired without change anything, just a complete writing of the bootloader and software. I don't want to buy the toolbox just to repair my Lumia 520, I don't need it, I'm just a home user not a repairing company...
melhisedec said:
As far as I read, JTAG is a toolbox for repairing Phones which have the same problem, but what we are trying to do is without this toolbox, we have a dead phone at home. Microsoft said is a hardware failure and they must change complete motherboard, but with Jtag Toolbox can be repaired without change anything, just a complete writing of the bootloader and software. I don't want to buy the toolbox just to repair my Lumia 520, I don't need it, I'm just a home user not a repairing company...
Click to expand...
Click to collapse
are you should to find testpoint for qcom9008. and flashing phone.
Mine was running everything give I install windows 10 just give the battery does not know dai was appearing this message (Erro Unable to find a bootable option error. Press any key to shut down,) Lumia 925 Brazil
---------- Post added at 03:41 AM ---------- Previous post was at 03:36 AM ----------
Mine was running everything give I install windows 10 just give the battery does not know dai was appearing this message (Erro Unable to find a bootable option error. Press any key to shut down)
Usually, is the main problem with Lumia Software update and stupid engineers from Microsoft does not fix it...
you deleted header partition, and lumia don't power on. help you only jtag.
I didn't know anything about this problem of almost any Lumia device until my phone has done the automatic software update from Win8 to 8.1 or 10, I don't know which one... And the the phone restarted with this stupid problem:
"ERROR: Unable to find a bootable option. Press any key to shut down"...
I have one week of searching over the internet to fix this but i couldn't make it...
If i can remove or unlock the bootloader, maybe I can force the phone to be Flashed with WDRT 1.34 and no more error:
"The FFU file is not correctly signed or not signed for this device."
melhisedec said:
I
Click to expand...
Click to collapse
Only you can help the programmer and all) nokia, wpinternals not flashing it. pins or seek to enter the 9008 regime (disassembly required).
partition table got off
i know this problems on my lumia 720(1 motheboard- After the firmware is not those files, 2 motherboards- After stitched sbl3 not true - died).
jtag helped to you, and me.
InsaneNutter said:
Hi,
Nope i could never fix the phone, I spent loads of time messing about with it however think it was a hardware related problem.
I've given it back to my friend and shes since got a new phone.
Click to expand...
Click to collapse
Cool. I had the same issue and many other issues with my 520. I have a very cool way of fixing this and all other issues if you struggle to start the phone up. If you are interested, let me know and I will explain to you. Very easy and process takes about 5 minutes.
Cheers
BruceKDallas said:
Cool. I had the same issue and many other issues with my 520. I have a very cool way of fixing this and all other issues if you struggle to start the phone up. If you are interested, let me know and I will explain to you. Very easy and process takes about 5 minutes.
Cheers
Click to expand...
Click to collapse
How did you do ?
melhisedec said:
As far as I read, JTAG is a toolbox for repairing Phones which have the same problem, but what we are trying to do is without this toolbox, we have a dead phone at home. Microsoft said is a hardware failure and they must change complete motherboard, but with Jtag Toolbox can be repaired without change anything, just a complete writing of the bootloader and software. I don't want to buy the toolbox just to repair my Lumia 520, I don't need it, I'm just a home user not a repairing company...
Click to expand...
Click to collapse
Did you follow http://forum.xda-developers.com/showthread.php?t=2515453 correctly?
InsaneNutter said:
A friend has asked me to look at this Nokia Lumia 520, apparently it turned on one day and displayed this error message "unable to find a bootable option. Press any key to shutdown"
Nokia Software Update for Retial recognises the phone and says software can be installed:
This downloads fine and starts the install process, however always fails with the message "phone not supported by nokia software updater retail"
I have also tried using NaviFirm+, searching for the product code 059S3T5 which lets me download the RM914_3058.50000.1425.0006_RETAIL_eu_euro1_327_06_452364_prd_signed firmware.
However i'm unable to flash this with the Nokia Care Suite, it states: 0xFA001106: Signature check of FFU file fails. Reason(s): The FFU file is not correctly signed or not signed for this device.
Has anyone got any suggestions on what else i can try to flash this firmware? or to try fix the phone?
I was following the tutorial here Flash/unbrand Lumia devices thinking if the firmware was re flashed all would be fine.
Cheers for any advice
Click to expand...
Click to collapse
hy bro try this...... http://forum.gsmhosting.com/vbb/f67...mc-error-unable-find-bootable-option-1931094/ i have sucses
feherneoh said:
I have seen this error millions of times on 520, and could fix it always
what you'll need:
PC
micro USB cable
WPInternals
.hex loader for 520
.ffu for 520
T4 screwdriver
Small wire
All you have to do is to short the resistor on eMMC clock lane, and connect USB, phone will be in emergency mode. You can either select unlock or relock in WPInternals, but for unlock, be sure to use an SBL3, because that won't fix the problem on its own.
The best would be selecting relock, then flashing the ffu, so EFIESP gets fixed
If you need help finding that resistor, PM me
Click to expand...
Click to collapse
Ok, so I found the resistor on a picture in another forum - so I just short it out and connect to USB while still shorted?
SamFirm Tool A.I.O
Hello guys
I have created a little tool to download Software Tools ,
check & Download latest Samsung & Apple Firmware,
and Bypass FRP (MTP Mode),
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Changelog:
1.0.0
• Download All Odin3 & Samsung USB Drivers (All Versions)
• Check & Download Latest Samsung Firmware File.
• Fixed firmware lookup and download issue
• Download & Auto Decrypt , auto Extract zip File
• Save File Name By (Model, Build Number, Android version, CSC Code, File Type, Release Date)
Example:
- SM-J700H_J700HXXS3BRL3_Marshmallow(Android 6.0.1)_EGY_Update Rom_20190121.zip
- SM-J700H_J700HXXS3BRL3_Marshmallow(Android 6.0.1)_EGY_Factory Rom (4 File)_20190121.zip
- SM-A260F_A260FXXS8ATJ1_Oreo(Android 8.1.0)_EGY_Factory Rom (5 File)_20201127.zip
1.2.0
• Added Some opreations in MTP Mode
• Read Device information
• Factory Reset
• Enter Download Mode
• Exit Download Mode
1.3.0
• Added Samsung Bypass FRP (MTP Mode) => Open Youtube URl
1.3.1
• Added Samsung Bypass FRP (MTP Mode) => Open Apps From Galaxy Store ( first in world )
1.3.2
• Added One Click Bypass FRP (MTP Mode) => Supported More Brands ( first in world )
No Need To Select Any Devices Or Brands
Just Connect & Click Bypass FRP
1.3.3
•Fixed Some Bugs (With Some Users Using Windows 7 )
• Added One Click Bypass FRP (MTP Mode) => Supported Google Pixel Devices ( first in world )
1.4.0
• Added One Click Bypass FRP (MTP Mode) => Supported Nokia Devices ( first in world )
Support More Models For Brands :-
Nokia / Huawei / Sony / Lenovo
== added Support To Download More Tools :-
** Sony Tools
** MTK Flash Tools
** SPD Flash Tools
** QLM Flash Tools
************************
== added ADB functions :-
** Read Device info
** Enable Arabic Language
** Reset Screenlock
** Reset FRP
** Reboot Device
************************
== added Fastboot functions :-
** Read Device info
** Reboot Device
************************
== Fixed Some Bugs For :-
-bypass FRP MTP
-Check internet Connection
************************
1.4.1
== add Support To Read MTK Scatter File :-
** Extract Firmware full info (Model, FW Version ,etc... )
** Extract Important Address (FRP ,UserData ,persist,...)
************************
== add New Method To MTP Bypass FRP.
== Bypass FRP (Offline)
************************
1.4.2
== add Support To Read MTK Scatter File :-
** Extract Firmware full info (Model, FW Version ,etc... )
** Extract Important Address (FRP ,UserData ,persist,...)
** Fixed Reaad Scatter files (New)
** add Description for Important Address (New)
************************
== add New Method To MTP Bypass FRP.
== Bypass FRP (Offline)
== Support Bypass FRP For Sharp Devices (New)
************************
1.4.3
== add Support To Bypass MTK offline Auth CPU:
Supported SoCs
mt6261
mt6572
mt6580
mt6582
mt6735
mt6737
mt6739
mt6755
mt6757
mt6761
mt6763
mt6765
mt6768
mt6771
mt6785
mt6799
mt6873
mt6885
mt8127
mt8163
mt8173
mt8695
== add New Method To Bypass MTP FRP .
== add Direct Download and install all USB Drivers .
== update all Flash Tools To latest Version .
== Enabled Samsung Download Firmware Option:
-- Check Crc32
-- Decrypt Manual
************************
1.5.3 (Paid)
Whats New:
Add Support MTK One Click
No need to select any model
No need to select any Scatter File
No need to select any DA/preloader
== One Click Read info
== One Click Format + FRP
== One Click Format Userdata
== One Click FRP
== One Click FRP( Samsung mtk) no need to select any partition
== One Click Reset Mi Account AntiRelock
Just Click >> Connect Brom >>> Opreation Done
Supported more Devices including
Lenovo,Samsung,Huawei, Xiaomi, Oppo ,infinix , Vivo, Meizu ,ZTE , Alcatel,Tecno...Etc
Based on the following Mediatek SoC types:
MT6572
MT6580
MT6582
MT6592
MT6595
MT6735
MT6737
MT6739
MT6753
MT6755
MT6757
MT6761
MT6763
MT6765
MT6768
MT6771
MT6779
MT6785
MT6795
MT6797
MT6799
MT6833
************************
MTP BypassFRP Supported Brands : Samsung, HTC, Xiaomi, Redmi, Huawei, Honor, OPPO, Realme, Meizu , Nokia,LG, Motorola, Google Pixel, Oneplus, Innjoo, Asus, Archos, Wiko, Itel, Gionee, Sico, Blu, Lava,, infinix, Tecno, Sony, Alcatel, Lenovo, ZTE, VFD, vivo, Yxtel, etc.........
Important
Before Using This Tool , you Need To Download And install
Microsoft .NET Framework 4.7.2
* For all Windows operating systems except Windows RT 8.1:
Download the Microsoft .NET Framework 4.7.2 offline installer package now.
* For Windows RT 8.1:
Download the Microsoft .NET Framework 4.7.2 package now.
Microsoft Visual C++ 2008 & Microsoft Visual C++ 2010
Microsoft Visual C++ 2008 Redistributable Package (x86) .
Microsoft Visual C++ 2010 Redistributable Package (x86) .
important ......
If you'r Osis 64Bit you Must Disable Signature Drivers First
Before Make ByPass FRP
see How To make it
https://www.youtube.com/watch?v=71YAIw7_-kg
=====================================
How To Fix Tool Problems ?
=====================================
Problem 1#
Tool Not Open
Fix
Before Using This Tool , you Need To Download And install
Microsoft .NET Framework 4.7.2
* For all Windows operating systems except Windows RT 8.1:
Download the Microsoft .NET Framework 4.7.2 offline installer package now.
* For Windows RT 8.1:
Download the Microsoft .NET Framework 4.7.2 package now.
Microsoft Visual C++ 2008 & Microsoft Visual C++ 2010
Microsoft Visual C++ 2008 Redistributable Package (x86) .
Microsoft Visual C++ 2010 Redistributable Package (x86) .
=====================================
Problem 2#
installing Drivers.... Failed
when Make MTP Bypass FRP
Fix
you need To Extract Tool into another partion
Dont Extract in C Partion
=====================================
Problem 3#
Opening Browser.... Failed
when Make MTP Bypass FRP
Fix
you Need to Disable Signature Drivers First
Before Make ByPass FRP
From Software Tools (tab)
Or Make it Manual , See vedio
https://www.youtube.com/watch?v=71YAIw7_-kg
=====================================
SamFirm Playlist
https://www.youtube.com/watch?v=mEmz..._wY14Au31EuV6-
Download Section :
SamFirm_Tool_A.i.o_v1.0.0 (Free) Direct , MediaFire
SamFirm_Tool_A.i.o_v1.2.0 (Free) Direct , MediaFire
SamFirm_Tool_A.i.o_v1.3.0 (Free) Direct , MediaFire
SamFirm_Tool_A.i.o_v1.3.1 (Free) Direct , MediaFire
SamFirm_Tool_A.i.o_v1.3.2 (Free) Direct , MediaFire
SamFirm_Tool_A.i.o_v1.3.3 (Free) Direct , MediaFire
SamFirm_Tool_A.i.o_v1.4.0 (Free) MediaFire
SamFirm_Tool_A.i.o_v1.4.1 (Free) Direct
SamFirm_Tool_A.i.o_v1.4.2 (Free) Direct
SamFirm_Tool_A.i.o_v1.4.3 (Free) Direct , MediaFire , Mega
SamFirm_Tool_A.i.o_v1.5.3 (Paid) Deleted
Best Regards,
AcaSilver (Mahmoud Salah)
acasilver said:
SamFirm Tool A.I.O
Hello guys
I have created a little tool to download Software Tools ,
check & Download latest Samsung & Apple Firmware,
and Bypass FRP (MTP Mode),
Tool Functions :-
== Software Tools (tab)
View attachment 5171685
== Samsung (tab)
View attachment 5171687
== Apple (tab)
View attachment 5171689
== Bypass FRP (tab)
View attachment 5171691
== Settings (tab)
View attachment 5171693
Changelog:
1.0.0
• Download All Odin3 & Samsung USB Drivers (All Versions)
• Check & Download Latest Samsung Firmware File.
• Fixed firmware lookup and download issue
• Download & Auto Decrypt , auto Extract zip File
• Save File Name By (Model, Build Number, Android version, CSC Code, File Type, Release Date)
Example:
- SM-J700H_J700HXXS3BRL3_Marshmallow(Android 6.0.1)_EGY_Update Rom_20190121.zip
- SM-J700H_J700HXXS3BRL3_Marshmallow(Android 6.0.1)_EGY_Factory Rom (4 File)_20190121.zip
- SM-A260F_A260FXXS8ATJ1_Oreo(Android 8.1.0)_EGY_Factory Rom (5 File)_20201127.zip
1.2.0
• Added Some opreations in MTP Mode
• Read Device information
• Factory Reset
• Enter Download Mode
• Exit Download Mode
1.3.0
• Added Samsung Bypass FRP (MTP Mode) => Open Youtube URl
1.3.1
• Added Samsung Bypass FRP (MTP Mode) => Open Apps From Galaxy Store ( first in world )
1.3.2
• Added One Click Bypass FRP (MTP Mode) => Supported More Brands ( first in world )
No Need To Select Any Devices Or Brands
Just Connect & Click Bypass FRP
1.3.3
•Fixed Some Bugs (With Some Users Using Windows 7 )
• Added One Click Bypass FRP (MTP Mode) => Supported Google Pixel Devices ( first in world )
Important
Before Using This Tool , you Need To Download And install
Microsoft .NET Framework 4.7.2
* For all Windows operating systems except Windows RT 8.1:
Download the Microsoft .NET Framework 4.7.2 offline installer package now.
* For Windows RT 8.1:
Download the Microsoft .NET Framework 4.7.2 package now.
Microsoft Visual C++ 2008 & Microsoft Visual C++ 2010
Microsoft Visual C++ 2008 Redistributable Package (x86) .
Microsoft Visual C++ 2010 Redistributable Package (x86) .
important ......
If you'r Osis 64Bit you Must Disable Signature Drivers First
Before Make ByPass FRP
see How To make it
https://www.youtube.com/watch?v=71YAIw7_-kg
Download Section :
SamFirm_Tool_A.i.o_v1.0.0 Direct , MediaFire
SamFirm_Tool_A.i.o_v1.2.0 Direct , MediaFire
SamFirm_Tool_A.i.o_v1.3.0 Direct , MediaFire
SamFirm_Tool_A.i.o_v1.3.1 Direct , MediaFire
SamFirm_Tool_A.i.o_v1.3.2 Direct , MediaFire
SamFirm_Tool_A.i.o_v1.3.3 Latest Direct , MediaFire
=====================================
Google Pixel 2 XL Android 11 FRP Bypass Using SamFirm
SM-A107F Android 10 U7 FRP Bypass Using SamFirm
SM-G611F Android 9.0 U1 FRP Bypass Using SamFirm
SM-J700H Android 6.0.1 U3 FRP Bypass Using SamFirm
How To Fix C++2008 / C++2010 errors
SamFirm Playlist
https://www.youtube.com/watch?v=mEmz..._wY14Au31EuV6-
Best Regards,
AcaSilver (Mahmoud Salah)
View attachment 5171681 View attachment 5171683
View attachment 5171675
Click to expand...
Click to collapse
yo lo uso aqui en nicaragua todo al 100 si les da problemas de conexion fail
aconsejo deshabilitar los driver firmados en win10
ajustes
actualizacion y seguridad
recuperacion
le damos en reiniciar ahora
luego ya saven que mas !!!
Translation:
I use it here in Nicaragua all 100 if it gives them connection problems fail
I advise disabling the signed drivers in win10
settings
update and security
Recovery
we give him restart now
then already know what else !!!
Hello, I have such an error when extracting files and here is my question, how to fix it, please help okey?
PLANETKA said:
Hello, I have such an error when extracting files and here is my question, how to fix it, please help okey?
Click to expand...
Click to collapse
Change download path, from local disk c to another partition
How to do it, I ask, can you write it to me?
PLANETKA said:
How to do it, I ask, can you write it to me?
Click to expand...
Click to collapse
Just extract tool into another directory,
Or change download path from setting
Good afternoon. Tell me what the problem is the program writes: "Checking internet Connection: Fail". I live in Russia, I use Windows 7 x64, driver signature verification is disabled. And he turned off checking the signature of drivers, and tried the button in your program, but does not download firmware, not programs-Checking internet Connection: Fail, Connection Very Slow, Operation Done. and does not Bypass Checking internet Connection : Fail, Operation is Done. The Internet connection to the router is fiber-optic, and then to the laptop - Wi-Fi, the connection speed is 200 Mb/s .
PLANETKA said:
How to do it, I ask, can you write it to me?
Click to expand...
Click to collapse
Use the disk not C and change where to download in the program settings.
Translation: Use the disk not C and change where to download in the program settings.
Priparat23rus said:
Диск не С используйи и в настройках программы поменяй куда скачивать.
Translation: Use the disk not C and change where to download in the program settings.
Click to expand...
Click to collapse
1. Welcome to XDA. We hope you enjoy your stay.
2. Please post in English as per XDA Rule #4.
3. Thank you for your cooperation.
-Regards: Badger50
hey i been trying to do frp bypass with samifirm tool aio v1.3.3 on samsung galaxy s10 running android 10 for a couple of days now but everytime same thing, connects, installs, says opening the browser on your device... operation done... done but nothing happens on the device, cant get the browser or any of the bypass tricks 2 work. ive watched pretty much every vid on youtube, followed all the steps n updated everything but just wont open browser on my device. ive tried pretty much all the new frp tools, flashed firmware but nothing works, could you please help!!!!!!
darbde said:
hey i been trying to do frp bypass with samifirm tool aio v1.3.3 on samsung galaxy s10 running android 10 for a couple of days now but everytime same thing, connects, installs, says opening the browser on your device... operation done... done but nothing happens on the device, cant get the browser or any of the bypass tricks 2 work. ive watched pretty much every vid on youtube, followed all the steps n updated everything but just wont open browser on my device. ive tried pretty much all the new frp tools, flashed firmware but nothing works, could you please help!!!!!!
Click to expand...
Click to collapse
Try to downgrade firmware and try again,
Priparat23rus said:
Good afternoon. Tell me what the problem is the program writes: "Checking internet Connection: Fail". I live in Russia, I use Windows 7 x64, driver signature verification is disabled. And he turned off checking the signature of drivers, and tried the button in your program, but does not download firmware, not programs-Checking internet Connection: Fail, Connection Very Slow, Operation Done. and does not Bypass Checking internet Connection : Fail, Operation is Done. The Internet connection to the router is fiber-optic, and then to the laptop - Wi-Fi, the connection speed is 200 Mb/s .
Click to expand...
Click to collapse
I want contact with you by team viewer
Please download it, and contact with me on Facebook
acasilver said:
Try to downgrade firmware and try again,
Click to expand...
Click to collapse
Im running android 10 U9 is there any way 2 diengrade or rollback the binary 2 U4 or U5??
sir opning brower me faild hora he..........mene disble bhi ker diya apne bataya vese fir bhi koyi soluton nahi ho raha hai
sm-g9860 is missing....
Thanks for your work.
royalbanna_is_here said:
sir opning brower me faild hora he..........mene disble bhi ker diya apne bataya vese fir bhi koyi soluton nahi ho raha hai
Click to expand...
Click to collapse
=====================================
Problem 3#
Opening Browser.... Failed
when Make MTP Bypass FRP
Fix
you Need to Disable Signature Drivers First
Before Make ByPass FRP
From Software Tools (tab)
Or Make it Manual , See vedio
=====================================
1.4.0 bugs
1. Your Themida Protection is awful. I have INSTALLED Fiddler for my own purposes but your tool says that some monitor program is RUNNING! It's absolutely false. I've rebooted windows for assure of unloading any suspicious programs but samfirm is still thinking that monitor is running!
2. Tool crashes on "PC info" after some seconds. I think it is on Harddisk, RAM or Network collecting
demovirus said:
1.4.0 bugs
1. Your Themida Protection is awful. I have INSTALLED Fiddler for my own purposes but your tool says that some monitor program is RUNNING! It's absolutely false. I've rebooted windows for assure of unloading any suspicious programs but samfirm is still thinking that monitor is running!
2. Tool crashes on "PC info" after some seconds. I think it is on Harddisk, RAM or Network collecting
Click to expand...
Click to collapse
Thanks for your report, Iwill check and fix it
acasilver said:
SamFirm Tool A.I.O
Hello guys
I have created a little tool to download Software Tools ,
check & Download latest Samsung & Apple Firmware,
and Bypass FRP (MTP Mode),
Tool Functions :-
View attachment 5197697
View attachment 5197699
View attachment 5197701
View attachment 5197703
View attachment 5197709
View attachment 5197711
View attachment 5197713
View attachment 5197715
Changelog:
1.0.0
• Download All Odin3 & Samsung USB Drivers (All Versions)
• Check & Download Latest Samsung Firmware File.
• Fixed firmware lookup and download issue
• Download & Auto Decrypt , auto Extract zip File
• Save File Name By (Model, Build Number, Android version, CSC Code, File Type, Release Date)
Example:
- SM-J700H_J700HXXS3BRL3_Marshmallow(Android 6.0.1)_EGY_Update Rom_20190121.zip
- SM-J700H_J700HXXS3BRL3_Marshmallow(Android 6.0.1)_EGY_Factory Rom (4 File)_20190121.zip
- SM-A260F_A260FXXS8ATJ1_Oreo(Android 8.1.0)_EGY_Factory Rom (5 File)_20201127.zip
1.2.0
• Added Some opreations in MTP Mode
• Read Device information
• Factory Reset
• Enter Download Mode
• Exit Download Mode
1.3.0
• Added Samsung Bypass FRP (MTP Mode) => Open Youtube URl
1.3.1
• Added Samsung Bypass FRP (MTP Mode) => Open Apps From Galaxy Store ( first in world )
1.3.2
• Added One Click Bypass FRP (MTP Mode) => Supported More Brands ( first in world )
No Need To Select Any Devices Or Brands
Just Connect & Click Bypass FRP
1.3.3
•Fixed Some Bugs (With Some Users Using Windows 7 )
• Added One Click Bypass FRP (MTP Mode) => Supported Google Pixel Devices ( first in world )
1.4.0
• Added One Click Bypass FRP (MTP Mode) => Supported Nokia Devices ( first in world )
Support More Models For Brands :-
Nokia / Huawei / Sony / Lenovo
== added Support To Download More Tools :-
** Sony Tools
** MTK Flash Tools
** SPD Flash Tools
** QLM Flash Tools
************************
== added ADB functions :-
** Read Device info
** Enable Arabic Language
** Reset Screenlock
** Reset FRP
** Reboot Device
************************
== added Fastboot functions :-
** Read Device info
** Reboot Device
************************
== Fixed Some Bugs For :-
-bypass FRP MTP
-Check internet Connection
************************
MTP BypassFRP Supported Brands : Samsung, HTC, Xiaomi, Redmi, Huawei, Honor, OPPO, Realme, Meizu , Nokia,LG, Motorola, Google Pixel, Oneplus, Innjoo, Asus, Archos, Wiko, Itel, Gionee, Sico, Blu, Lava,, infinix, Tecno, Sony, Alcatel, Lenovo, ZTE, VFD, vivo, Yxtel, etc.........
Important
Before Using This Tool , you Need To Download And install
Microsoft .NET Framework 4.7.2
* For all Windows operating systems except Windows RT 8.1:
Download the Microsoft .NET Framework 4.7.2 offline installer package now.
* For Windows RT 8.1:
Download the Microsoft .NET Framework 4.7.2 package now.
Microsoft Visual C++ 2008 & Microsoft Visual C++ 2010
Microsoft Visual C++ 2008 Redistributable Package (x86) .
Microsoft Visual C++ 2010 Redistributable Package (x86) .
important ......
If you'r Osis 64Bit you Must Disable Signature Drivers First
Before Make ByPass FRP
see How To make it
https://www.youtube.com/watch?v=71YAIw7_-kg
=====================================
How To Fix Tool Problems ?
=====================================
Problem 1#
Tool Not Open
Fix
Before Using This Tool , you Need To Download And install
Microsoft .NET Framework 4.7.2
* For all Windows operating systems except Windows RT 8.1:
Download the Microsoft .NET Framework 4.7.2 offline installer package now.
* For Windows RT 8.1:
Download the Microsoft .NET Framework 4.7.2 package now.
Microsoft Visual C++ 2008 & Microsoft Visual C++ 2010
Microsoft Visual C++ 2008 Redistributable Package (x86) .
Microsoft Visual C++ 2010 Redistributable Package (x86) .
=====================================
Problem 2#
installing Drivers.... Failed
when Make MTP Bypass FRP
View attachment 5172535
Fix
you need To Extract Tool into another partion
Dont Extract in C Partion
View attachment 5172547
=====================================
Problem 3#
Opening Browser.... Failed
when Make MTP Bypass FRP
View attachment 5172537
Fix
you Need to Disable Signature Drivers First
Before Make ByPass FRP
From Software Tools (tab)
View attachment 5172539
Or Make it Manual , See vedio
https://www.youtube.com/watch?v=71YAIw7_-kg
=====================================
Nokia 1 Plus Android 10 FRP Bypass Using SamFirm
Google Pixel 2 XL Android 11 FRP Bypass Using SamFirm
SM-A107F Android 10 U7 FRP Bypass Using SamFirm
SM-G611F Android 9.0 U1 FRP Bypass Using SamFirm
How To Fix C++2008 / C++2010 errors
SamFirm Playlist
https://www.youtube.com/watch?v=mEmz..._wY14Au31EuV6-
Download Section :
SamFirm_Tool_A.i.o_v1.0.0 Direct , MediaFire
SamFirm_Tool_A.i.o_v1.2.0 Direct , MediaFire
SamFirm_Tool_A.i.o_v1.3.0 Direct , MediaFire
SamFirm_Tool_A.i.o_v1.3.1 Direct , MediaFire
SamFirm_Tool_A.i.o_v1.3.2 Direct , MediaFire
SamFirm_Tool_A.i.o_v1.3.3 Direct , MediaFire
SamFirm_Tool_A.i.o_v1.4.0 Final MediaFire
Best Regards,
AcaSilver (Mahmoud Salah)
View attachment 5171681 View attachment 5171683
View attachment 5171675
Click to expand...
Click to collapse
thank you so much it's work keep working
Thread closed as OP removed its content.
- Oswald Boelcke
*********************
e
jastahooman said:
In developing...
Click to expand...
Click to collapse
interesting... looking forward to this
Wow! Waiting impatiently. Will that be bare-bones WM 6.5 or with Sense?
Looking forward to it
Nice, can you please send me kitchen, i also have a solution for the expired certificate problem so you can surf the web. You can extract them from Windows 7, 8 , 10 in the right format and then install with the Builtin certificate manager.
If someone can share them from Windows 10 in a supported format, cer does work maybe der, crt sstl but pem cant be read or converted to the other Formats without private Key.
HERE IS THE SHORT TUT AND FULL TUT LINK
Updating List of Trusted Root Certificates in Windows | Windows OS Hub
All Windows versions have a built-in feature for automatically updating root certificates from the Microsoft websites. MSFT, as part of the Microsoft Trusted Root Certificate Program, maintains and publishes a…
woshub.com
AND HOW TO GET ALL FRESH WIN10/WIN11 Certificates
certificates using the Sigcheck tool. This tool allows you to compare the list of certificates installed on the computer with the list of root certificates on the Microsoft website (you can download an offline file with up-to-date certificates authrootstl.cab).
You can manually transfer the root certificate file between Windows computers using the Export/Import options.
You can export any certificate to a .CER file by clicking on it and selecting All Tasks -> Export;
You can import this certificate on another computer using the option All Tasks -> Import.
Certutil: Download Trusted Root Certificates from Windows UpdateCertutil.exe CLI tool can be used to manage certificates (introduced in Windows 10, for Windows 7 is available as a separate update). It can be used to download an up-to-date list of root certificates from Windows Update and save it to an SST file.
To generate an SST file on a computer running Windows 10 or 11 and having direct access to the Internet, open the elevated command prompt and run the command:
certutil.exe -generateSSTFromWU C:\PS\roots.sst
Updated SST file.
CertUtil: -generateSSTFromWU command completed successfully.
Click to expand...
Click to collapse
You can visit archive.org after adding the certs uploaded in this post, from the Fileexplorer.
It ewould be nice if someone could start a certficiates megathreads,Contianing the ones used by Webbrowser other OSes etc to and the standard Windows Moible Root CAs.
Windows Mobile Root Certificates - Connectivity Analyzer
If the Microsoft Remote Connectivity Analyzer is unable to follow the certificate chain to the trusted root, then it displays the following error: "The security certificate on the server is not valid. Support code: 0x80072f0d."
docs.microsoft.com
Namely
Certificate Authority5.05.0 + MSFP6.0Thawte Server CAYesYesYesThawte Premium Server CAYesYesYesGTE CyberTrust RootYesYesYesGTE CyberTrust Global RootYesYesYesSecure Server Certification Authority (RSA)YesYesYesGlobalSign Root CAYesYesYesEntrust.net Secure Server Certification AuthorityYesYesYesEntrust.net Certification Authority (2048)YesYesYesVerisign Class 3 Public Primary Certification AuthorityYesYesYesVerisign Class 2 Public Primary Certification AuthorityYesYesYesEquifax Secure Certificate AuthorityYesYesYesValiCert Class 2 Policy Validation AuthorityNoYesYesAAA Certificate Services (Comodo CA Limited)NoNoYesAddTrust External CA RootNoNoYesBaltimore CyberTrust RootNoNoYesGo Daddy Class 2 Certification AuthorityNoNoYesStarfield Class 2 Certification AuthorityNoNoYes
There is also a new Windows Mobile build reuglary updated
Download Windows Embedded CE 6.0 Cumulative Product Update Rollup Package (through 12/31/2015) from Official Microsoft Download Center
www.microsoft.com
You can find sysbuilders with searching for
Windows Embedded CE 6.0 R3or under its prerename
Windows Embedded Compact
docs.microsoft.com
There are several variants bu kernel seems to be same.
So maybe this helps.
There is also a new Windows Mobile Build and UPdate from 2016
Download Windows Embedded CE 6.0 Cumulative Product Update Rollup Package (through 12/31/2015) from Official Microsoft Download Center
www.microsoft.com
Windows Embedded Handheld
docs.microsoft.com