Database Users

Problem root galaxy s 2

I m trying to root my new galaxy s 2 i9100 with this way.http://forum.xda-developers.com/show....php?t=1075278
i follow all the steps but i have a serious problem.
in step 8. "Click root and wait for it to finish. Install Busybox and all that good stuff." the SuperOneClick bugs.
this is all tha i get in my screen:
SuperOneClick v1.7.0.0
Killing ADB Server...
OK
Starting ADB Server...
* daemon not running. starting it now on port 5037 *
* daemon started successfully *
OK
Waiting for device...
OK
Pushing psneuter...
2820 KB/s (585731 bytes in 0.202s)
OK
chmod psneuter...
OK
Running psneuter...
please help!!

Do it again and follow the instructions .
- Make sure your device is in USB debugging mode: Settings -> Applications -> Development -> USB debugging
- Reboot your device into download mode: Turn the device off, then power it on again by pressing and holding VolumeDown + Home + Power simultaneously. You will know when you are in download mode, it is really obvious
- Start ODIN
- Connect the device to your computer using USB
- Wait a few seconds, the ODIN screen should show you that a device is now connected
- Make sure that in ODIN NOTHING is checked, except the "Auto reboot" and "F. Reset Time" checkboxes. Press the "PDA" button, and select the "XWKDD_insecure.tar" file.
- Press "Start". ODIN you should now be flashing the kernel, and the device should reboot.
- Wait until the device is rebooted, and while still being connected over USB, start SuperOneClick, and press ROOT.
- Reboot the device
- Done !
jje

JJEgan said:
Do it again and follow the instructions .
- Make sure your device is in USB debugging mode: Settings -> Applications -> Development -> USB debugging
- Reboot your device into download mode: Turn the device off, then power it on again by pressing and holding VolumeDown + Home + Power simultaneously. You will know when you are in download mode, it is really obvious
- Start ODIN
- Connect the device to your computer using USB
- Wait a few seconds, the ODIN screen should show you that a device is now connected
- Make sure that in ODIN NOTHING is checked, except the "Auto reboot" and "F. Reset Time" checkboxes. Press the "PDA" button, and select the "XWKDD_insecure.tar" file.
- Press "Start". ODIN you should now be flashing the kernel, and the device should reboot.
- Wait until the device is rebooted, and while still being connected over USB, start SuperOneClick, and press ROOT.
- Reboot the device
- Done !
jje
Click to expand...
Click to collapse
I ve done all this but in the step 8 is the problem.
it's the second time that i done it.

Try closing Odin before running superoneclick.

Is debugging mode on or off .
jje

JJEgan said:
Is debugging mode on or off .
jje
Click to expand...
Click to collapse
is on here is two images.
The one when i run SuperOneClick and the second from the phone.

Can you post the steps you are taking to root .
Like install xxxx via Odin
Phone set at XX
steps 1 , 2, 3 , 4 etc from the beginning .
jje

JJEgan said:
Can you post the steps you are taking to root .
Like install xxxx via Odin
Phone set at XX
steps 1 , 2, 3 , 4 etc from the beginning .
jje
Click to expand...
Click to collapse
Finally i found the problem.
The kernel that was with the same name wasn't the same.
ouffff!!!
Thank you very much man!!

im having this problem too, maybies ive flashed a wrong version of the kernal tho this is the link to it.
http://forum.xda-developers.com/attachment.php?attachmentid=581915&d=1304094698
im running a new from the box yesterday s2 gingerbread 2.3.3 uk 3network
gt-I9100 Baseband I9100NEKD5
It says kernal version [email protected] #2 (tho i have flashed the above file)
I have followed all tuts to the tee
Help would be appreciated

warrent2 said:
im having this problem too, maybies ive flashed a wrong version of the kernal tho this is the link to it.
http://forum.xda-developers.com/attachment.php?attachmentid=581915&d=1304094698
im running a new from the box yesterday s2 gingerbread 2.3.3 uk 3network
gt-I9100 Baseband I9100NEKD5
It says kernal version [email protected] #2 (tho i have flashed the above file)
I have followed all tuts to the tee
Help would be appreciated
Click to expand...
Click to collapse
Maybe is wrong kernel.
The name is the same but i don't know something goes wrong.
Flash with this kernel and you will be allright.
http://forum.xda-developers.com/showthread.php?t=1056334

Thanks for the quick reply,
thats the same file i flashed. I re-downloaded the file from the link you posted and flashed again in Odin. Same result I can confirm the phone is in usb de-bug, the phone was turned off and started in the download mode (black screen) I got pass ok in Odin. The phone restarted afterwards but i get the same. When the program gets to this stage it locks up and has to be ended by task manager. Im running windows 7 x64 pc with i7850 processor ddr3 ram..
on the tut the file is called XWKDD_insecure.tar inside the rar file on the post its called zimage with no extension, i had to manually add the .tar to get odin to view it.
([email protected]) Running psneuter...
Any suggestions?

warrent2 said:
Thanks for the quick reply,
t
on the tut the file is called XWKDD_insecure.tar inside the rar file on the post its called zimage with no extension, i had to manually add the .tar to get odin to view it.
Any suggestions?
Click to expand...
Click to collapse
Why did you extract a tar file to make a tar file the instructions are to Flash XWKDD insecure .tar . as PDA through Odin
Long guide (for beginners)
- Download the attached ODIN file and extract the .zip file
- Download the attached XWKDD, but do NOT extract the .tar file
jje

cheers m8 ure a star, the file was associated with winrar and i didnt realise that had a .tar ext, jumped the gun a lil. Thanks to the lad who posted earlier it worked first time leats this post go tme registered on here great forum!

warrent2 said:
cheers m8 ure a star, the file was associated with winrar and i didnt realise that had a .tar ext, jumped the gun a lil. Thanks to the lad who posted earlier it worked first time leats this post go tme registered on here great forum!
Click to expand...
Click to collapse
You were very instructive!!!

warrent2 said:
cheers m8 ure a star, the file was associated with winrar and i didnt realise that had a .tar ext, jumped the gun a lil. Thanks to the lad who posted earlier it worked first time leats this post go tme registered on here great forum!
Click to expand...
Click to collapse
so no problem at all!!

Hey guys , I rooted my SGS2 with XWKDD_insecure.tar and superoneclick.
Everthing worked fine.
But after a while I found out, that I couldn´t make any videos with the device´s camera. All new recorded vids couldn´t be played. Message "unrecognised file type".
So, I decided to get some other ROM. I wanded to flash the litening 2.0 Rom and flashed it with odin.
But no flash changed my device. Yesterday I had thousands of konversations with experts from a german android forum. noone could held me.
Every odin flash seemed to finish correctly with PASS. But after reboot, my device always has the same state, the same kernel version, all installed apps after my rooting were gone, messages, images... all were gone, except these I had on my device before the rooting I did.
If I install e.g. CWM Manager and select the action "boot into recovery mode", I only can see the Options "reboot now", "install update from sd", "wipe data" and "wipe partition".
All data saved by my device, doesn´t stay on it, after i rebooted it.
It looks like after every boot, my device loads a special recovery point, like system recovery on e.g. Win XP.
Anybody an idea?

Nobody here who can help me with this problem? ...

Hello Humphrey,
when you boot into recovery, you can see ' update.zip' , usually that is cwm. Rom manager installs update-zip before you can use rom manager. Install update.zip via rom manager just incase that update-zip is not cwm, unless you know it is. When you install update-zip, via recovery and it comes back as unable to verify zip, then you are not rooted.
The cwm will allow you to format the caches and system, delvik and battery and then allow you to install a complete rom with a rooted kernel.To be quite honest, Oden could brick your phone because you are using 2 hardwares, computer and phone. I have found it easier to download a zipped rom to your sd card and use cwm to flash it. Remember to format everything I said but not usb or sd. I have found Designgears Cognition 1.13 rom, not 1.15, to be ideal. I also use Zeam desktop, which I find ideal. Cognition is already rooted. Rom manager has glitches, so I don't use it to reboot into recovery or anything else but to look at roms, which I don't download via rommanger. Also, I'm fed-up with downloading stock roms and then having to find a rooted rom and using Odin.
I hope you find this useful.
Adrian
Sent from my GT-I9100 using XDA Premium App

[Guide]Upgrade SGS I9000 to 2.3.6 (Value Pack) & Root It

Hey Users,
Heres a guide for upgrading to 2.3.6 form any firmware..This guide is ONLY for SGS GT-I9000..
This guide can also be used if your phone has a boot loop and you cannot access CWM Recovery..(Provided your Phone Boots atleast to "Galaxy S GT-I9000" & Download mode)
Note:
1.Phone must have atleast 60% Battery
2.Take Backup of all your phone data like contacts,etc. as this process will factory reset your phone
--Plus take imp data from your Internal SD Card(for safety)
Take backups by using 3rd party apps like Astro for Apps,SMS Backup & Restore for SMS,ETC.
3.Enable USB Debugging (IMPORTANT)
--Goto Settings->Application->Development->Turn On USB Debugging
4.If your phone is being connected to the PC for the first time (in Download mode), then make sure that it installs all the drivers
Downloads:
1.Android 2.3.6 Value Pack from here(password: samfirmware.com)
2.Root File from here or here
3.USB Drivers form here(This Is Optional if it is already installed by your phone, else you need to download it and install it)
4.PIT file form here
Steps:
To Upgrade:
Once the download is complete, extract the files in one place
1.Run Odin3 and add the files as follows:
--PIT: Put the PIT File,
--PDA: Put the Code File,
--Phone: Put the Modem File,
--CSC: Put the CSC File,
--(IMAGE ATTACHED BELOW :1)--
2.Put your SGS to download mode. Do so by 3-Button Combo..
--Volume Down+Home (Center) Button+Power Button
Press and hold it till you see "Download" (Attached Image :3)
And then connect it to your system for odin to recognise it, make sure there is the a yellow box in "ID:COM" (Shown in Image :1)
If its not recognising make sure the drivers are installed..If the are then try other versions of odin3(Also attached with 2.3.6 File)..
3.Hit the start button and wait for some time..
Remember IF there is no progress for 5 mins or so, disconnect your phone and try it again..and also use different odin versions (Also attached with 2.3.6 File)
The phone will automatically reboot..The first reboot make take 5~10 minutes..
To Root:
1.Run Odin from the downloaded file and add only 1 file
--PDA:Put the CF-Root file that you just downloaded
--(Image Attached :2)--
2.Attached the phone in Download mode (As Mentioned Earlier)
--wait for it to be recognised by odin..
3.Hit the start button and wait for a few seconds
The phone will automatically reboot..After reboot check if Superuser application is there with other 2 new applications on your phone (As a System file i.e; you cannot delete this application)
(This checks if your phone is rooted or not)
Enjoy
Edit:I have requested the moderator..and i apologize for the same..

Please move it to general section.
Sent from my GT-I9000 using Tapatalk 2

Not again,why do you keep on posting in dev section?

I'm sry but WAT'S THE PASSWORD!!! for first zip?

Tchindalia:
1. Start reading stickies
http://forum.xda-developers.com/showthread.php?p=20056581
2. As a consequence of understanding 1.)
Tell moderator you have posted in wrong section (Dev) when the right place would be (General).
3. If not 2.)
You will probably get reported.
I would recommend reading Ramads thread http://forum.xda-developers.com/showthread.php?p=14273101
instead of yours. He has already answered the questions people are going to ask here.

Plz the Root file , the link doesn't work with me
Sent from my GT-I9000 using xda app-developers app

AFAIK everyone here is aware of this procedure. Pls post such threads in the General section

Hi everybody
Ive just wanted to extract the zip files , so i nedded the PASSWORD, Can anybody please help me

I need the pit file , it's not included in Rom files

hello
saw man said:
I need the pit file , it's not included in Rom files
Click to expand...
Click to collapse
I've tried all of the above but my device was stuck before I could check USB debugging.
So I got a Fail while trying to flash.
The eroor on Odin 3.1 is Can't open the serial(COM) port.
Can you help, please?
---------- Post added at 05:50 PM ---------- Previous post was at 05:42 PM ----------
tchindalia said:
Hey Users,
Heres a guide for upgrading to 2.3.6 form any firmware..This guide is ONLY for SGS GT-I9000..
This guide can also be used if your phone has a boot loop and you cannot access CWM Recovery..(Provided your Phone Boots atleast to "Galaxy S GT-I9000" & Download mode)
Note:
1.Phone must have atleast 60% Battery
2.Take Backup of all your phone data like contacts,etc. as this process will factory reset your phone
--Plus take imp data from your Internal SD Card(for safety)
Take backups by using 3rd party apps like Astro for Apps,SMS Backup & Restore for SMS,ETC.
3.Enable USB Debugging (IMPORTANT)
--Goto Settings->Application->Development->Turn On USB Debugging
4.If your phone is being connected to the PC for the first time (in Download mode), then make sure that it installs all the drivers
Downloads:
1.Android 2.3.6 Value Pack from here(password: samfirmware.com)
2.Root File from here or here
3.USB Drivers form here(This Is Optional if it is already installed by your phone, else you need to download it and install it)
4.PIT file form here
Steps:
To Upgrade:
Once the download is complete, extract the files in one place
1.Run Odin3 and add the files as follows:
--PIT: Put the PIT File,
--PDA: Put the Code File,
--Phone: Put the Modem File,
--CSC: Put the CSC File,
--(IMAGE ATTACHED BELOW :1)--
2.Put your SGS to download mode. Do so by 3-Button Combo..
--Volume Down+Home (Center) Button+Power Button
Press and hold it till you see "Download" (Attached Image :3)
And then connect it to your system for odin to recognise it, make sure there is the a yellow box in "ID:COM" (Shown in Image :1)
If its not recognising make sure the drivers are installed..If the are then try other versions of odin3(Also attached with 2.3.6 File)..
3.Hit the start button and wait for some time..
Remember IF there is no progress for 5 mins or so, disconnect your phone and try it again..and also use different odin versions (Also attached with 2.3.6 File)
The phone will automatically reboot..The first reboot make take 5~10 minutes..
To Root:
1.Run Odin from the downloaded file and add only 1 file
--PDA:Put the CF-Root file that you just downloaded
--(Image Attached :2)--
2.Attached the phone in Download mode (As Mentioned Earlier)
--wait for it to be recognised by odin..
3.Hit the start button and wait for a few seconds
The phone will automatically reboot..After reboot check if Superuser application is there with other 2 new applications on your phone (As a System file i.e; you cannot delete this application)
(This checks if your phone is rooted or not)
Enjoy
Edit:I have requested the moderator..and i apologize for the same..
Click to expand...
Click to collapse
I've tried all of the above but my device was stuck before I could check USB debugging.
So I got a Fail while trying to flash.
The eroor on Odin 3.1 is Can't open the serial(COM) port.
Can you help, please?

Its your second post in wrong section.
And there are lots of such guides already there in this forum so whats new in your?

this is the guide I've used to root my i9000 3 weeks ago. Just had to get Odin 1.7 by searching on Google. Thank you !

thnx.... for the links ...

how can i update to ics ?

Thank you tchindalia

Can I flash this to my hunagrian (PANJV2) device? In other words, can I flash firmware other than Hungarian to my Hungarian phone?

Anteino said:
Can I flash this to my hunagrian (PANJV2) device? In other words, can I flash firmware other than Hungarian to my Hungarian phone?
Click to expand...
Click to collapse
yes, you can flash any firmware to it, 90%+ of firmwares have Hungarian language in them

Excelsior!
Thanks very much for this guide, it was quite clear cut and helpful. Only things I mention incase anyone else has similar issues; getting the installer for the Samsung drivers to work on W8 took many clicks and admin access and I had to track down Odin 1.7 for it to work.
Samsung Galaxy S GT-I9000 2.2 -> 2.3.6

thank you for the excellent post. breathed new life in my old phone

Thank you!
Your guide helped me . And the phone is much faster and smoother with this value pack. Also I got more free RAM .

Galaxy S3 i9300 Unbrick [restore to stock rom] [noobs][easy]

Hi guys! This is a noob-proof guide on how to flash stock samsung firmware on your i9300. Whether you have bricked it or just want the stock firmware back. Here's how to do it (detailed explaination)
WARNING! : This is only for the GT i9300 (international version) , Check your device before proceeding. Also you might lose all your data. So backup! i am not responsible if you brick your phone(although very unlikely) by not following the guide properly
Also you will lose your custom recovery, Custom ROM and will not longer have root
Ok lets begin!
1. Make sure you have the samsung drivers installed on your pc (http://bit.ly/SDaIIE)
2. Your device should have at least 80% battery left
3. Enable USB Debugging by going to Settings>Developer Options>Tick the Usb debugging tick box!
Files needed :
1. Android 4.1.2 I9300XXEMA1 for Galaxy S3 I9300 - http://bit.ly/10vkxdj
2. Odin 3.07 - http://bit.ly/16aRzF4
Extract The firmware Zip file until you get a file with a .tar extension and some other files. Do not extract furthur
Extract odin zip file till you get Odin3 v3.07.exe
Now here comes the actual flashing part
1. Power off your smartphone. Wait 5-6 seconds for vibration to confirm complete switch off.
2. Now, get into Download Mode by pressing and holding Volume Down, Home and Power button simultaneously until Samsung Galaxy logo appears in phone screen. Wait few seconds and your phone will be in download mode.
3.Open odin as administrator and connect your s3 to your computer with usb cable
4. You will get a message "Added" in the message box in odin and You should also see COM port with a number in Yellow if you successfully added your device.
if you don't get this , try another usb port.. if it still doesn't come , reinstall drivers.
5. Select these files from I9300XXEMA1 folder in Odin at respective buttons:
Click the PDA Button, and select the .tar.md5 file here with *code* appearing in its name
Click the Phone Button, and select file with *modem* in its name (leave if there is no such file)
Click the CSC Button, and select file with *csc* in its name (leave if there is no such file)
Click the PIT Button, and select the .pit file. Use only if you got it while extracting , otherwise ignore it.
6. make sure Auto Reboot and F. Reset Time checkboxes are selected. Also, make sure that Re-Partition checkbox is selected, only if you are using a .pit file
7. Double check everything above and hit start!
8. once flashing is complete the phone will reboot automatically and soon you will see a PASS message with green background in the left-most box at the very top of the Odin. You can then unplug the USB cable to disconnect your device from computer.
congratz , you have just restored your i9300!
If this has helped you make sure to hit the thanks button!

what have you developed?

We already know Odin, and this doesn't UNBRICK anything
Sent from my GT-I9300 using xda premium

This is so worthy of development thread. ...:banghead:
Sent from my GT-I9300 using xda premium

Helpful post to some,,,,,however the unbrick part is misleading as all this does is flash a stock ROM.

Only soft brick... like any other Samsung device.

Reported not development plus we have all this information already posted .
OP is splattering this post all over the forum .
jje

[Q] Odin accidental zip flash =/

I was supposed to unpack the tarfile from the zip, but since my computer decided to not recognize the zip and using the rar icon I thought it was the tar itself and flashed it only to realise my mistake as Odin said the flash failed. As of right now, every time I start my device, it says "Firmware upgrade encountered and issue. Please select recovery mode in Kies & try again." and shows a picture that looks like *Phone**Triangle**Computer*.
Kies emergency recovery does not recognize the device.
Trying to start the phone in recovery mode takes me to the *Phone**Triangle**Computer*.
Download mode > Flashing a stock rom = fail (Yes, it's unpacked this time)
Any suggestions? Thanks in advance.
P.S. Now before anyone bothers to help me out here.. I know.. I'm an idiot, and anyone who takes his or her time to help out here is my hero for the rest of my life <3 D.S.

Try to flash stock firmware with a pit file search for pit file in original development section for you device model

armedking said:
Try to flash stock firmware with a pit file search for pit file in original development section for you device model
Click to expand...
Click to collapse
Is there even a pit-file for 9505 yet?
I didn't find it if there is one.
Trying to flash a stock in just a few minutes, when the download is complete. If it does not work, I'll try to find a pit.
Thanks for the reply <3

For the i9500 ther is i think dont know about i9505 try asking a dev and there is a thread here on page two I think somebody had same problem like you he fixt it changing usb poort and original usb cabel helpt him try to do that and flash stock firmware without pit file first hope you get it sort al out buddy

PixelPatrik said:
Is there even a pit-file for 9505 yet?
I didn't find it if there is one.
Trying to flash a stock in just a few minutes, when the download is complete. If it does not work, I'll try to find a pit.
Thanks for the reply <3
Click to expand...
Click to collapse
see my sig for pit file with odin :good:

Alright, so I got a lot further this time.
I figured out how to get into Download mode again, suddenly I need to press and hold the combo a little while longer than I did before, or it will go to *phone**triangle**computer*.
I got the official firmware into PDA in Odin 3.07 this time around and connected my phone to the computer after I loaded PDA.
I then pressed start and VOILA!!! Thanks fellas!

You welcome enjoy

PixelPatrik said:
I was supposed to unpack the tarfile from the zip, but since my computer decided to not recognize the zip and using the rar icon I thought it was the tar itself and flashed it only to realise my mistake as Odin said the flash failed. As of right now, every time I start my device, it says "Firmware upgrade encountered and issue. Please select recovery mode in Kies & try again." and shows a picture that looks like *Phone**Triangle**Computer*.
Kies emergency recovery does not recognize the device.
Trying to start the phone in recovery mode takes me to the *Phone**Triangle**Computer*.
Download mode > Flashing a stock rom = fail (Yes, it's unpacked this time)
Any suggestions? Thanks in advance.
P.S. Now before anyone bothers to help me out here.. I know.. I'm an idiot, and anyone who takes his or her time to help out here is my hero for the rest of my life <3 D.S.
Click to expand...
Click to collapse
yes u need the pit file while flashing

[Q] ODIN keeps crashing!

Hello so i believed i soft bricked my Galaxy S4 when trying to install a custom ROM. I tied to factory reset in my settings but it stayed at the downloading stage for multiple hours so i had to reboot. I downloaded a factory PDA file and PIT file to use with ODIN but everytime i click start it says ODIN is not responding and after it fixes it says Failed. Please help i really would like to fix my phone asap.

TheSamsungGuyS4 said:
Hello so i believed i soft bricked my Galaxy S4 when trying to install a custom ROM. I tied to factory reset in my settings but it stayed at the downloading stage for multiple hours so i had to reboot. I downloaded a factory PDA file and PIT file to use with ODIN but everytime i click start it says ODIN is not responding and after it fixes it says Failed. Please help i really would like to fix my phone asap.
Click to expand...
Click to collapse
Make sure you didnt connect your phone to USB 3.0 Port

TheSamsungGuyS4 said:
Hello so i believed i soft bricked my Galaxy S4 when trying to install a custom ROM. I tied to factory reset in my settings but it stayed at the downloading stage for multiple hours so i had to reboot. I downloaded a factory PDA file and PIT file to use with ODIN but everytime i click start it says ODIN is not responding and after it fixes it says Failed. Please help i really would like to fix my phone asap.
Click to expand...
Click to collapse
Bott in recovery, then wipe cach and dalvik, this will help if you're still on boot screen, and also for bottloop.
About USB 3.0. I always connect my devices via USB 3.0, it doesn't matter, the only thing is to have Intel drivers (Win 7) and not Microsoft (Win 8).
Reinstall KIES/drivers on your computer then connect your devices.
I think it should be OK
Hallelujah !

TheSamsungGuyS4 said:
Hello so i believed i soft bricked my Galaxy S4 when trying to install a custom ROM. I tied to factory reset in my settings but it stayed at the downloading stage for multiple hours so i had to reboot. I downloaded a factory PDA file and PIT file to use with ODIN but everytime i click start it says ODIN is not responding and after it fixes it says Failed. Please help i really would like to fix my phone asap.
Click to expand...
Click to collapse
if you use PDA file you don't need pit file
and please note,when flashing PDA file using ODIN check F.reset time and auto-reboot option only
also, before flash using ODIN make sure ODIN recognize your device ( the box will turn to blue ) then you can press start to start the process
petrusconsult said:
Bott in recovery, then wipe cach and dalvik, this will help if you're still on boot screen, and also for bottloop.
About USB 3.0. I always connect my devices via USB 3.0, it doesn't matter, the only thing is to have Intel drivers (Win 7) and not Microsoft (Win 8).
Reinstall KIES/drivers on your computer then connect your devices.
I think it should be OK
Hallelujah !
Click to expand...
Click to collapse
No, I've use windows 8.1 and it work fine and it'll work on other windows as well ..please note that someone maybe install windows 7 OS over their current OS and it will create more problem to them..

Zaraee said:
if you use PDA file you don't need pit file
and please note,when flashing PDA file using ODIN check F.reset time and auto-reboot option only
also, before flash using ODIN make sure ODIN recognize your device ( the box will turn to blue ) then you can press start to start the process
No, I've use windows 8.1 and it work fine and it'll work on other windows as well ..please note that someone maybe install windows 7 OS over their current OS and it will create more problem to them..
Click to expand...
Click to collapse
With one-file rom, if you want to make a repartition, you need PIT FILE !

Yes..but why bother to repartition your device..as many of them bricked their device by flashing wrong pit file
Sent from my GT-I9500