Related
All your actions with the phone is at your own risk. The authors are not liable. This is just your choice.
PLEASE read full instructions before you start.
RECOMMENDED ONLY FOR EXPERIENCED USERS.
This was tested ONLY on MEIZU MX4 and ONLY FIRMWARE 4.2.8.2A, ANY OTHER FIRMWARE/PHONE - YOU WILL RECEIVE BRICK PHONE.
(с)
ONLY FOR MEIZU MX4 AND ONLY FIRMWARE 4.2.8.2A. Don't use the that apk on Lollipop or your device will brick
Hello everyone, i changed chinese apk for unlock bootloader, and replaced chinese recovery, on TWRP 2 8.6.0 recovery.
1. Download Flyme OS 4.2.8.2A stock firmware an official webpage Meizu
2. Flash it in stock recovery and select WIPE DATA
3. Get root permission
4. Download and install that APK - drive.google.com/open?id=0B_Gd_o_kBWgLNHFuZW5kMlFzV2s
5. Open that app, and provide root permission.
6. Press "Press to UNLOCK BootLoader" - and wait, you will see "Unlock Finished"
7. After, will be available recovery mode, and you press to "Enter Recovery Mode"
8. Your phone reboot and enters for normal recovery - TWRP 2.8.6.0.
Thanks for the great work!
At last we're getting closer to opening up our meizu phones.
Can the phone with this, unlocked bootloader flash "I" international roms from OTA?
How to relock?
ideosx5 said:
How to relock?
Click to expand...
Click to collapse
Reflash FLyme rom (with Flyme recovery, be carefull!)
Or flash stock uboot
Successfully upgraded MX4 "A" edition phone to "I" using following method:
Installed 4.2.8 "A" stock firmware.
1. Installed apk method unlock (this thread).
2. Downloaded 4.5.7 "I" firmware, extracted and created system.img using (linux):
$ sdat2img system.transfer.list system.new.dat system.img
for windows, see this guide from Meizufans.
3. Boot into fastboot mode (now unlocked) using "VOL -" + "POWER"
4. fastboot flash boot boot.img
WAIT
fastboot flash system system.img
WAIT
5.Reboot into recovery
6. Full wipe
7. Install super su
8. Reboot
VOILA - 4.5.7 "I"
Remember to block/deactivate system updates once system has booted for first time.
Is it possible for someone to upload recovery.img of TWRP please ? I'd like to try
---------- Post added at 10:16 AM ---------- Previous post was at 09:22 AM ----------
I got it, I'm fixing the splash screen dimensions ahah^^
---------- Post added at 11:03 AM ---------- Previous post was at 10:16 AM ----------
It was a little harder than I expected but it's here : http://www.mediafire.com/download/26b963db1k489db/new-recovery.img
Learnincurve said:
Successfully upgraded MX4 "A" edition phone to "I" using following method:
Installed 4.2.8 "A" stock firmware.
Click to expand...
Click to collapse
Good, but there is easy way download that rom, and install it for TWRP(select full wipe, include internal storage) - emmaus.pro/MX4_custom_roms/Flyme/4.5.7i_twrp.zip
and there all stock Flyme roms for twrp - emmaus.pro/?dir=MX4_custom_roms/Flyme
Author all rom "nikk3d" russian 4pda users - 4pda.ru/forum/index.php?showuser=2196261
And this method works even on newest firmware, let's say 4.5.6i downgraded to 4.2.8i via 4.0.4i? Or is a easy variant of previous method, patched uboot by meizu remains after 4.5.6i upgrade if i understand, no matter if you downgrate to Kitkat?
update for TWRP : http://www.mediafire.com/download/f6a65ccpgrfaopw/TWRPr5.img
Changelog :
I corrected "Select storage" position, corrected some shifts on the main screen
zaurikk said:
Good, but there is easy way download that rom, and install it for TWRP(select full wipe, include internal storage) - emmaus.pro/MX4_custom_roms/Flyme/4.5.7i_twrp.zip
and there all stock Flyme roms for twrp - emmaus.pro/?dir=MX4_custom_roms/Flyme
Author all rom "nikk3d" russian 4pda users - 4pda.ru/forum/index.php?showuser=2196261
Click to expand...
Click to collapse
I have an MX4 originally with Ubuntu touch, I tried to flash 4.5.7i from emmaus.pro.
It failed, updater binary error. I checked the recovery log and it says write error, no space left.
Does anybody have any clue?
Thanks,
Note: I already tried a wipe out (even internal storage). No issues with the cyanogenmod roms from emmaus.pro.
Is someone trying to make fom Meizu MX5?
Sent from my MX5 using Tapatalk
itresw said:
I have an MX4 originally with Ubuntu touch, I tried to flash 4.5.7i from emmaus.pro.
It failed, updater binary error. I checked the recovery log and it says write error, no space left.
Does anybody have any clue?
Thanks,
Note: I already tried a wipe out (even internal storage). No issues with the cyanogenmod roms from emmaus.pro.
Click to expand...
Click to collapse
i think, mx4 ubuntu touch version, and standard china version, - internal partitions(storage) name - different, so you gives write an error.
isko01 said:
Is someone trying to make fom Meizu MX5?
Sent from my MX5 using Tapatalk
Click to expand...
Click to collapse
Now it is impossible.
zaurikk said:
Now it is impossible.
Click to expand...
Click to collapse
Thanks for reply . Can I know how much is good Caynogenmod on MX4? Is everything working good?
Sent from my MX5 using Tapatalk
isko01 said:
Thanks for reply . Can I know how much is good Caynogenmod on MX4? Is everything working good?
Sent from my MX5 using Tapatalk
Click to expand...
Click to collapse
Yep, all needed function now it work - gsm module, wi-fi, bluetooth and etc.
The only problem, that ROM not officially for Cyanogen team, that rom created by ordinary users and updated 1-2 times on month.
i tried on M2 note, i suppose it bricked.is it possible earlier condition working?i look up some unbrick videos, can repairs make my phone working?thanks.
No way to unbrick it, this is for MX4 not M2 Note !!! You'll need to change the motherboard, sorry
zaurikk said:
Yep, all needed function now it work - gsm module, wi-fi, bluetooth and etc.
The only problem, that ROM not officially for Cyanogen team, that rom created by ordinary users and updated 1-2 times on month.
Click to expand...
Click to collapse
Thanks to all user's who making this for MX4. They are really engineers! I hope they will try for MX5.
Yes, the problem it is not official, and we cant get new update.
Why we don't write a email to Canynogen and tell them that we open the bootloader and put CM. But we want they make CM for MX4 and MX5, with new CM and updates?
Sent from my MX5 using Tapatalk
my meizu is bricked, ne response please help me
hi someone had tested this app already? is it surely gonna work??
and after i will unlock the bootloader i can instal any rom? like Mokee and CM12.1??
Hello guys.
I have successfully ported TWRP 3.0.0-0 for our Smart Prime 6.
It's 100% working !!
There are NO BUGS !! :good:
DOWNLOAD
NEW LINK: DOWNLOAD
________________________________________
How to install
Via app:
1) Download TWRP 3.0.0-0 from the link above and place it on internal storage of your phone.
2) Download Flashify app from Google Play Store.
3) Open Flashify app.
4) Grant root permissions.
5) Click "Recovery image" and then click "Choose a file"
6) Navigate to the folder where you placed TWRP 3.0.0-0 and choose the .IMG file.
7) Press "Yup!" button and wait.
8) After a while the phone will require reboot. So click "reboot" button.
9) Phone will reboot and automatically boot into TWRP, so you can press reboot to system.
10) Enjoy!
Special thanks to Oneb1t for modded .fstab file! :highfive:
edit: you can use Flashfire app too instead of Flashify, but it's not recommended, because the latest version of the Flashfire app is not flashing properly.
Brilliant! Thank you so much! Do you know any custom ROM what is better than the factory ROM?
There is no custom ROM for this phone yet.
But I'm trying to make LITE ROM.
Adreno306™ said:
There is no custom ROM for this phone yet.
But I'm trying to make LITE ROM.
Click to expand...
Click to collapse
Do you think it's easier/possible to adapt a ROM from a similar device like say, the Alcatel
Pop 2 (5) Premium ? I don't know if there's any ROM for that phone tho, but since it's branded as Alcatel you might get more support from the community here than by using Vodafone's name.
Hello, Demonlord6.
I have tried to make a stock flashable ROM via dumping the system folder and the boot.img file, but without success.
It does not boot properly.. when I tried to flash it without dalvik/system wipe everything was as before.
When I tried to wipe /system and dalvik first and then flash the ROM, it causes bootloop.
So now I'm trying to fix this issue..
I don't know where the problem is.
So when this issue will be solved I will try to build a ROM from Alcatel phones with same specs.
Adreno306™ said:
Hello, Demonlord6.
I have tried to make a stock flashable ROM via dumping the system folder and the boot.img file, but without success.
It does not boot properly.. when I tried to flash it without dalvik/system wipe everything was as before.
When I tried to wipe /system and dalvik first and then flash the ROM, it causes bootloop.
So now I'm trying to fix this issue..
I don't know where the problem is.
So when this issue will be solved I will try to build a ROM from Alcatel phones with same specs.
Click to expand...
Click to collapse
Hey, Andreno306
I don't know much about Rom's in that level of expertise I'm afraid :/ but I did some digging and came across this simple tutorial on XDA:
http://forum.xda-developers.com/showthread.php?t=2387941
I imagine it does not work for every single device out there, at least not with modifying stuff after, but it might be a good starting point I think, in fact I would try to actually make one myself had I a working PC currently at home. But even if I did I had no way of testing it because this is currently my daily driver phone.
Just wanted to say that I'm also very interested in getting a slim ROM for this device. I can't offer any expertise I'm afraid! Just wanted to show that there are people interested in your project.
:highfive:
Stock Kernel
Thanks, it works great.
This is little off-topic but does anyone has the stock kernel, i flashed NeoKernel but it is not that good and i forgot to make a backup do can anyone please link me to the stock kernel?
vojta_horanek said:
Thanks, it works great.
This is little off-topic but does anyone has the stock kernel, i flashed NeoKernel but it is not that good and i forgot to make a backup do can anyone please link me to the stock kernel?
Click to expand...
Click to collapse
I have one
https://mega.nz/#!tMJD3B4T!f6m2ELYCVupqGCcN2aGbkrNzEqijLu7au-7usEfeVL0
But I recommend to restore it with the flashify app, because that's how the backup was made.
If, for some reason, you don't/can't restore it, then you can always try Sugar on the PC which basically restores everything to factory settings (recovery, kernel, etc, it all gets reset)
Demonlord6 said:
I have one
But I recommend to restore it with the flashify app, because that's how the backup was made.
If, for some reason, you don't/can't restore it, then you can always try Sugar on the PC which basically restores everything to factory settings (recovery, kernel, etc, it all gets reset)
Click to expand...
Click to collapse
Restored and my phone keeps turning off after boot(once i saw the turn off screen, other times it just vibrates at boot screen), isnt it the wrong file? (flashed wia flashify)
I was able to restore the boot from TWRP (lucky i made a backup this time)
vojta_horanek said:
Restored and my phone keeps turning off after boot(once i saw the turn off screen, other times it just vibrates at boot screen), isnt it the wrong file? (flashed wia flashify)
I was able to restore the boot from TWRP (lucky i made a backup this time)
Click to expand...
Click to collapse
Sorry there about the bootloop but glad u could restore it from TWRP, maybe it was because we have different ROM versions ?
Demonlord6 said:
Sorry there about the bootloop but glad u could restore it from TWRP, maybe it was because we have different ROM versions ?
Click to expand...
Click to collapse
I got this one: http://www.needrom.com/download/vodafone-smart-prime-6-vf-895n-debloatedclean-stock/#
vojta_horanek said:
I got this one: http://www.needrom.com/download/vodafone-smart-prime-6-vf-895n-debloatedclean-stock/#
Click to expand...
Click to collapse
Yeap, that's not the same version as my ROM, mine is not 130FNN etc. Maybe that's why it didn't work
Enviado do meu GT-S5280 através de Tapatalk
Sorry for the stupid question but... does it works on Smart Prime 7 too?
Has anyone installed that linked ROM? It seems to be what we are looking for... a slim debloated rom.
I presume we need to be rooted, install this TWRP, then flash that ROM?
It mentions unlocking the bootloader, I dont think I've seen any info anywhere about unlocking the bootloader.
Can anyone give a quick lowdown on all the steps required to install that ROM please?
Hi everyone, I discovered that Elephone Trunk and Smart Prime 6 have (almost) identical specs: https://www.devicespecifications.com...ison/c584481c6
So it would be great to "port" (or build ?) the official Nougat-OmniROM for Trunk to VF-895N: http://dl.omnirom.org/trunk/
Last but not least, here's official Vodafone Smart Prime 6 sources: Vodafone_Smart_prime_6_20150413.tar.xz
TWRP for vodafone smart max 4 990N (coolpad 8890u).
I tried this recovery image for vodafone smart max 4 990N (coolpad 8890u).
The phone is in a bootloop state. I think i have usb debugging enabled already.
So, in fastboot mode i can see the device in my pc in adb fastboot cmd.
Im trying to ''fastboot boot recovery.img" but it stops in ''booting..''.
Dont know whats the problem but for sure i can not find a specific twrp image for this device.
If i enter fastboot oem device-info it says ''(bootloader) Device unlocked: true''.
Any ideas ?
hi i was wondering if you could share how you did this or if you can make one for the Vodafone smart n9 (VFD720) it would help a lot of people out looking for this
Needed to root a Vodafone Smart Prime 6 (VF 895N) (got it from a friend because it became unresponsive from all the updated google play stuff ) to get linux-deploy running. Just wanted to leave a big thank you here for Adreno306 for his TRWP 3.0.0-0. it did the job very well!
Only the procedure to get it installed differed quite a bit for me, since Flashify is no longer available.
I wanted to preserve boot and just flash trwp to recover, what worked quite well.
The first thing I did was to boot the phone manually in recovery mode (Power+Vol up) and reset it to factory settings from there. It takes a little while. Then follow the setup, go to phone settings, enable developer mode and set usb debugging. If "unlock oem" is not available there, reboot into recovery again, set unlock there and reboot into bootloader.
The prerequisites are adb and fastboot, both must work. Means adb devices and fastboot devices must show the phone. What can make problems under win10 as it sometimes does not detect the phone in bootloader mode. An actual google usb driver is needed, as provided by google.
For me adb worked well, but when rebooted into bootloader with adb reboot bootloader, fastboot didnt detect the phone. With the phone still connected, the windows device manager showed an unknown device with and exclamation mark (!). Right click, install driver, select driver manually, select driver from device list, mark all devices (first entry) and click "disk", then point to the usb driver director and select "ADB fastboot driver". ( A more comprehensive description is available here )
Once adb and fastboot detect the device, it is time to prepare it. Boot to system (normal operation) first. Make sure that the TRWP 3.0.0-0.img is renamed to trwp.img and then
adb reboot bootloader
fastboot devices
fastboot oem unlock
fastboot boot trwp.img
Now the phone should show the trwp menu, set it up to root the phone and install SuperSU. Reboot into bootloader and
fastboot flash recovery trwp.img
fastboot reboot
Verify with adb reboot recovery, you should see trwp now. Reboot to system.
Now finally go into the app selector, start SuperSU, and root the phone. SuperSu uses trwp recovery mode to install its image and root is done.
Again, big thanks for providing the TRWP image!
Adreno306™ said:
Hello guys.
I have successfully ported TWRP 3.0.0-0 for our Smart Prime 6.
It's 100% working !!
There are NO BUGS !! :good:
DOWNLOAD
NEW LINK: DOWNLOAD
________________________________________
How to install
Via app:
1) Download TWRP 3.0.0-0 from the link above and place it on internal storage of your phone.
2) Download Flashify app from Google Play Store.
3) Open Flashify app.
4) Grant root permissions.
5) Click "Recovery image" and then click "Choose a file"
6) Navigate to the folder where you placed TWRP 3.0.0-0 and choose the .IMG file.
7) Press "Yup!" button and wait.
8) After a while the phone will require reboot. So click "reboot" button.
9) Phone will reboot and automatically boot into TWRP, so you can press reboot to system.
10) Enjoy!
Special thanks to Oneb1t for modded .fstab file! :highfive:
edit: you can use Flashfire app too instead of Flashify, but it's not recommended, because the latest version of the Flashfire app is not flashing properly.
Click to expand...
Click to collapse
Hi, I would like to try your tutorial but I can't root this phone (which is an important step in the tutorial), is there any way someone could help me??
Thanks
Android N Preview 2 npc91k (flashable & image with no encryption and dm verification)
This thread is for the second Android N Preview.
For Android N Preview 3 see: http://forum.xda-developers.com/nexus-6/general/android-n-preview-3-beta-npd35k-t3381845
For Android N Preview 4 see: http://forum.xda-developers.com/nexus-6/general/android-n-preview-4-beta-npd56n-t3399473
** DISCLAIMER: I AM NOT A DEVELOPER. I DO THIS AS A HOBBY AND SHARE MY FINDINGS IN CASE SOMEONE ELSE FINDS THEM USEFUL. **
** THIS WORKED ON MY DEVICE BUT IT MAY NOT WORK ON YOURS. APPLY AT YOUR OWN RISK **** The following are instruction for installing Android N Preview 2 image released by Google on 4/13/2016. After the installation you will have TWRP recovery 3.0.2-0 with the data partition erased and unencrypted if you use method 2, which means you will have ~ 3GB more space and ~ 10 seconds faster boot speed **Always backup your data before flashing something a total stranger gives you!
Method 1: Flash update through TWRP recovery (keeps your data and current recovery)
1- You need to have TWRP installed on your phone.
2- Download this flashable zip..
3- Copy to the phone internal storage and flash via recovery.
4- Reboot. Your data should still be intact and your OS is upgraded to N Preview 2. If your internal storage is unencrypted before flashing it remains unencrypted.
For some people this didn't work. It seems to be the case when you have been encrypted by your previous Android N installation, in which case TWRP seems to have difficulty reading the file, and that seemingly Preview 2 doesn't play nice with TWRP. It works best when you are unencrypted and your recovery is 3.0.2-0. Thanks to @gammaxgoblin, @blitzerking1, @Michael in ATL, @HueyT, and @PhillyFlyer for debugging and hints.
Method 2: Flash update using a computer (wipes everything, unencrypts data, and upgrades TWRP)
1- ALL of your data including the internal storage will be lost so make a backup. (If you know what you are doing and you are coming from unencrypted Marshmallow you can modify the instructions to not lose data but I won't help you with that).
2- Download this file. Note that it is NOT a flashable zip.
3- Unzip into a folder of your choice on your PC.
4- Open a command window (cmd) and cd to this directory. then run the following:
Code:
flash-all
5- Wait until prompted, then press key to reboot the phone.
6- Your data is wiped and your OS is upgraded to N with unencrypted internal storage. Your TWRP is also upgraded to 3.0.2-0.
Technical details: this is a repacking of the Google image with a modified Kernel and removed userdata and recovery images. Everything else is stock.
Problem downloading from Mega on a mobile browser? Change the page setting to "Request desktop site".
About root and other issues
To obtain root after installing this update you should flash SuperSU 2.71 (or higher) in recovery. Get it from here: http://forum.xda-developers.com/apps/supersu/2014-09-02-supersu-v2-05-t2868133. Despite the fact that SuperSU 2.71 is supposedly re-written for Android N, there are still some apps that seem to have a problem obtaining root. The commonest complaint on this thread so far has been about Adaway. If you want to block Ads just manually do what Adaway does. Download a hosts file from any ad block list server such as http://winhelp2002.mvps.org/hosts.htm, copy the files on your sdcard, boot the phone into recovery, and using the TWRP file manager replace the file /system/etc/hosts with this file and set its permissions to 644 (rw-r--r--).
wouldnt flash first go. redl now
no flash again
gammaxgoblin said:
wouldnt flash first go. redl now
no flash again
Click to expand...
Click to collapse
Same happened to me. It would not flash, same error
gammaxgoblin said:
wouldnt flash first go. redl now
no flash again
Click to expand...
Click to collapse
Can you open the zip that you downloaded and see if you can see the file that it is complaining about? What version of twrp are you using?
najoor said:
Can you open the zip that you downloaded and see if you can see the file that it is complaining about? What version of twrp are you using?
Click to expand...
Click to collapse
Same error for me as well. I can extract the zip and view the file it is talking about. I also tried on TWRP 3.0.1-0 and TWRP 3.0.2-0
Everything is working perfect for me with the new zip. I have a unencrypted phone and used 3.0.2 TWRP.
najoor said:
Can you open the zip that you downloaded and see if you can see the file that it is complaining about? What version of twrp are you using?
Click to expand...
Click to collapse
i tried 3.0.1 and 3.0.2 and i can also see the file
Method 2 works great
Method two works I used it myself
Shall I flash preview 2 directly from marshmallow?
Seems like TWRP is having a lot of troubles with each version of N Preview's encryption. I have same problem with both N6 and N6P, as do others in that forum too....:/
i have latest twrp, download a ota update from ofiicial site in zip file and flash it over in twrp. boot normally and works fine. only flash supersu 2.71 and it's unencrypted at all.
ps. TB not works for me ind N prew2 so i flash perv1, restore from TB and flash prew2 over it.
marius987 said:
i have latest twrp, download a ota update from ofiicial site in zip file and flash it over in twrp. boot normally and works fine. only flash supersu 2.71 and it's unencrypted at all.
ps. TB not works for me ind N prew2 so i flash perv1, restore from TB and flash prew2 over it.
Click to expand...
Click to collapse
Sorry for the stupid question. What do you mean for TB?
cerico76 said:
Sorry for the stupid question. What do you mean for TB?
Click to expand...
Click to collapse
I'm going to assume it stands for Titanium Backup.
Waiting for fixed method #1
outkastz said:
I'm going to assume it stands for Titanium Backup.
Click to expand...
Click to collapse
Ah,yes! Thanx!
Can someone please provide a link to the desktop website for the flashable zip?
Just to help with the installation of method 2, holding shift and right clicking a blank space in your unzipped folder, you can click open command window here. That will save you having to CD all the way to it.
Sent from my Nexus 6 using XDA-Developers mobile app
I did method 1. It upgraded fine. All my data remained. It killed root (expected this) and my TWRP. I was unencrypted before attempting.
I went and downloaded the latest TWRP and flashed via fastboot. Then downloaded latest SuperSU from http://forum.xda-developers.com/apps/supersu/2014-09-02-supersu-v2-05-t2868133 and flashed it via my newly installed TWRP. Root confirmed and all is well.
Good to go Thanks!
I've got an "Invalid boot image" issue :
Any tought ?
outpox said:
I've got an "Invalid boot image" issue :
Any tought ?
Click to expand...
Click to collapse
You may have to flash a previous stable release of marshmallow or lollipop from Google first and then try this because something seems to be corrupted in your system.
I had been struggeling myself alot with this but after looking everywhere I collected pieces of information all over XDA and fixed it.
Since all the information is scatterd around everywhere I thought it would be good to make a complete piece here.
I have only tested this with the device: (Honor 8 FRD-L09)
If anyone got this working on other devices please leave a comment so I can add it to this list for other people to see.
So here it goes:
1- First you need to be have an unlocked bootloader.
2- Flash via fastboot the new TWRP with decryption support Here
3- Download two files:
a- update.zip Link (1.5G)
b- update_data_full_hw_eu.zip Link(1.05G)
4- Flash these two files using TWRP (a then b)
5- Reflash TWRP (using fastboot)
Finally, to root, you need to flash this patched prerooted boot.img B378 root boot image (from SD card): Link(15.8MB)
You can do this with OldDroids TWRP or with surdu_petrus TWRP: Link(36.2MB) and Link(24,2MB)
1- Flash OldDroids or surdu_petrus TWRP
2- Select "Install" -> Click "Images" -> Go to External SD and select your rooted_b378_boot.img
3- When it asks where to install click boot.
4- Then reboot and install phh's superuser from the playstore (its the only superuser that works for now)
5- Install JRummy's Busybox Installer and install to /vendor/xbin
Done!
Note: To get AdAway working, go to Preferences, then scroll down to "Target hosts file" and set it to "custom target". Then set Custom target to "/vendor/etc/hosts"
If you have any questions feel free to send me a message I had much trouble with it too.
Credits to: morpheus302, Atarii, OldDroid, surdu_petrus and phhusson
thierrybla said:
I had been struggeling myself alot with this but after looking everywhere I collected pieces of information all over XDA and fixed it.
Since all the information is scatterd around everywhere I thought it would be good to make a complete piece here.
So here it goes:
1- First you need to be have an unlocked bootloader.
2- Flash via fastboot the new TWRP with decryption support Here
3- Download two files:
a- update.zip Link (1.5G)
b- update_data_full_hw_eu.zip Link(1.05G)
4- Flash these two files using TWRP (a then b)
5- Reflash TWRP (using fastboot)
Finally, to root, you need to flash this patched prerooted boot.img B378 root boot image (from SD card): Link(15.8MB)
You can do this only with OldDroids TWRP: Link(36.2MB)
1- Flash OldDroids TWRP
2- Select "Install" -> Click "Images" -> Go to External SD and select your rooted_b378_boot.img
3- When it asks where to install click boot.
4- Then reboot and install phh's superuser from the playstore (its the only superuser that works for now)
5- Install JRummy's Busybox Installer and install to /vendor/xbin
Done!
Note: To get AdAway working, go to Preferences, then scroll down to "Target hosts file" and set it to "custom target". Then set Custom target to "/vendor/etc/hosts"
If you have any questions feel free to send me a message I had much trouble with it too.
Credits to: morpheus302, Atarii, OldDroid and phhusson
Click to expand...
Click to collapse
Hello!
Can you please specify for which variants of the FRD is this valid?
Thank you
RM
omartins said:
Hello!
Can you please specify for which variants of the FRD is this valid?
Thank you
RM
Click to expand...
Click to collapse
I have only tested it on the FRD-L09
I can't say for sure if it works on the others, I'm sorry.
If you got this working on a different device please let me know.
Quick Question: I have installed normal TWRP 3.1.0.0, every time i want to install the newest SuperSu Beta, it resets TWRP completely. Is your guide also going to work for me, or do i have another problem?
david320te said:
Quick Question: I have installed normal TWRP 3.1.0.0, every time i want to install the newest SuperSu Beta, it resets TWRP completely. Is your guide also going to work for me, or do i have another problem?
Click to expand...
Click to collapse
Yes SuperSU doesn't work as far as I know you need Phh Superuser.
But if you already have nougat 7.0 B380 you can just begin at the boot.img installing step and it should work for you too.
Good luck!
Ok, but you linked "twrp-3.1.0.0-eva", i've installed "twrp-3.1.0.0-frp" - do you know, where the difference is?
Edit:
Well, something has gone wrong. Doesn't boot...stays on that screen forever...i tried restoring the backup i took while the system was read only with TWRP
david320te said:
Ok, but you linked "twrp-3.1.0.0-eva", i've installed "twrp-3.1.0.0-frp" - do you know, where the difference is?
Edit:
Well, something has gone wrong. Doesn't boot...stays on that screen forever...i tried restoring the backup i took while the system was read only with TWRP
Click to expand...
Click to collapse
The difference is that the TWRP that I linked can flash .img 's
wich you need to flash the boot.img
Try to get back in TWRP and start at step 1 just do the whole guide then your phone should boot again
david320te said:
Ok, but you linked "twrp-3.1.0.0-eva", i've installed "twrp-3.1.0.0-frp" - do you know, where the difference is?
Edit:
Well, something has gone wrong. Doesn't boot...stays on that screen forever...i tried restoring the backup i took while the system was read only with TWRP
Click to expand...
Click to collapse
The "twrp-3.1.0.0-eva" is for the Huawei P9, the "twrp-3.1.0.0-frD" is for the Honor 8.
And first boot after TWRP install can take longer that usual:
Q: Why does booting take so long?
A: Because of the decryption process which need to finish
its work before twrp tries to access /data partition.
Click to expand...
Click to collapse
Try flashing the pre-rooted boot.img via fastboot command line.
Worked for me.
Code:
Copy the pre-rooted boot.img to the adb/fastboot directory
(have usb debugging enabled etc etc, connect phone to computer)
Start a cmd box
adb reboot fastboot
fastboot flash boot rooted_b378_boot.img
reboot device.
N01tra said:
The "twrp-3.1.0.0-eva" is for the Huawei P9, the "twrp-3.1.0.0-frD" is for the Honor 8.
And first boot after TWRP install can take longer that usual:
Try flashing the pre-rooted boot.img via fastboot command line.
Worked for me.
Code:
Copy the pre-rooted boot.img to the adb/fastboot directory
(have usb debugging enabled etc etc, connect phone to computer)
Start a cmd box
adb reboot fastboot
fastboot flash boot rooted_b378_boot.img
reboot device.
Click to expand...
Click to collapse
I can boot into TWRP no Problem, as i said, i restored the backed up image (somehow after a factory reset, the stock apps as well as the keyboard was gone, i could not type in my wifi password) in TWRP, but it sat for about 10 Minutes on that screen when i turned the phone off.
I do not have very good Broadband, so i will start at the first step, installing the update files, linked in the first post.
N01tra said:
The "twrp-3.1.0.0-eva" is for the Huawei P9, the "twrp-3.1.0.0-frD" is for the Honor 8.
And first boot after TWRP install can take longer that usual:
Try flashing the pre-rooted boot.img via fastboot command line.
Worked for me.
Code:
Copy the pre-rooted boot.img to the adb/fastboot directory
(have usb debugging enabled etc etc, connect phone to computer)
Start a cmd box
adb reboot fastboot
fastboot flash boot rooted_b378_boot.img
reboot device.
Click to expand...
Click to collapse
You are right it is for P9 but it worked for me regardless though :fingers-crossed:
david320te said:
I can boot into TWRP no Problem, as i said, i restored the backed up image (somehow after a factory reset, the stock apps as well as the keyboard was gone, i could not type in my wifi password) in TWRP, but it sat for about 10 Minutes on that screen when i turned the phone off.
I do not have very good Broadband, so i will start at the first step, installing the update files, linked in the first post.
Click to expand...
Click to collapse
Yeah.. A FactoryReset seems to be a big "no no" after flashting TWRP as it will delete the keyboard and other stuff.
I was in that situation and restored a TWRP backup which got me back to booting into android, but somehow the Camera and LED (flashlight) didn't work.
Restoring an older and a complete backup did not help. Flashing the Update files did not help.
Eventually I ended up following the Honor 8 Rollback steps; going from Emui 5 (android 7) back to Emui 4.1 (android 6).
That also means the Bootloader is locked again, so you'll have to re-unlock it again (if you still have the code, you can use it again).
My steps after the Rollback:
- OTA updated back to Emui 5,
- Factory reset (BEFORE installing TWRP) and reboot.
- Enabled USB debugging,
- Unlock bootloader,
- Flashed TWRP and immediately after that I booted into recovery and rebooted,
- Rebooted to Fastboot (via adb reboot bootloader),
- Fastboot flashed that pre-rooted b378 boot.img and rebooted,
- Installed Phh's root.
N01tra said:
Yeah.. A FactoryReset seems to be a big "no no" after flashting TWRP as it will delete the keyboard and other stuff.
I was in that situation and restored a TWRP backup which got me back to booting into android, but somehow the Camera and LED (flashlight) didn't work.
Restoring an older and a complete backup did not help. Flashing the Update files did not help.
Eventually I ended up following the Honor 8 Rollback steps; going from Emui 5 (android 7) back to Emui 4.1 (android 6).
That also means the Bootloader is locked again, so you'll have to re-unlock it again (if you still have the code, you can use it again).
My steps after the Rollback:
- OTA updated back to Emui 5,
- Factory reset (BEFORE installing TWRP) and reboot.
- Enabled USB debugging,
- Unlock bootloader,
- Flashed TWRP and immediately after that I booted into recovery and rebooted,
- Rebooted to Fastboot (via adb reboot fastboot),
- Fastboot flashed that pre-rooted b378 boot.img and rebooted,
- Installed Phh's root.
Click to expand...
Click to collapse
I had the same as you describe here but I fixed it by flashing the 2 files I posted up here (a and b)
After doing it step by step as described in the first post, it worked I also flashed the P9 TWRP, just to make sure. It works! But i already miss Resurrection Remix from my Mi4c...
However, does this mean TWRP Backups are useless? :/
david320te said:
After doing it step by step as described in the first post, it worked I also flashed the P9 TWRP, just to make sure. It works! But i already miss Resurrection Remix from my Mi4c...
However, does this mean TWRP Backups are useless? :/
Click to expand...
Click to collapse
I'm glad to hear it works! :highfive:
TWRP backups never worked for me I always just flash it clean and then have titanium backup do the rest
Have a nice day
Hi,
maybe what I am going to ask sounds silly but as I am a kind of newbie hope you will forgive me
Why do we have to install a prerooted 378 image instead of a prerooted 380 Image. Aren't we on 380?
Where does this 378 image come from? Until now I only saw Nougat's 360 & 380 Roms.
I am already on 380 but my root doesn't seem to work properly so I wanted to give a try to thierrybla's OP's post but I don't know if to follow his instructions by using OldDroids TWRP to install his suggested prerooted 378 Image or instead by using OldDroids TWRP to install the other thread's Prerooted 380 img.
What shall I do if I'm already on 380 but would like to try thierrybla's procudure so see if I finally get a well-rooted 380 rom?
Any help would be appreciated.
fourcc said:
Hi,
maybe what I am going to ask sounds silly but as I am a kind of newbie hope you will forgive me
Why do we have to install a prerooted 378 image instead of a prerooted 380 Image. Aren't we on 380?
Where does this 378 image come from? Until now I only saw Nougat's 360 & 380 Roms.
I am already on 380 but my root doesn't seem to work properly so I wanted to give a try to thierrybla's OP's post but I don't know if to follow his instructions by using OldDroids TWRP to install his suggested prerooted 378 Image or instead by using OldDroids TWRP to install the other thread's Prerooted 380 img.
What shall I do if I'm already on 380 but would like to try thierrybla's procudure so see if I finally get a well-rooted 380 rom?
Any help would be appreciated.
Click to expand...
Click to collapse
Hey,
Your question is not stupid I can see why you are confused but everytime I tried to root or preroot something it didn't work for me I also run 380 and once I tried the prerooted 378 made by atariii it worked so there is no reason te be skeptical because I was in the same situation as you and this worked for me just give it a try you won't be disappointed
Thanks for your quick answer!!!
Ok, so I understand it is safe to install prerooted 378 image while being on nougat's 380. Thanks, I will try it right now!
fourcc said:
Thanks for your quick answer!!!
Ok, so I understand it is safe to install prerooted 378 image while being on nougat's 380. Thanks, I will try it right now!
Click to expand...
Click to collapse
Tell me how it went !
Goodluck!
Hey thierrybla, it worked beautifully! Thanks!
The only thing I did different is too install the prerooted image with Fastboot instead of the Oldroid Twrp.
I was afraid of messing my good working TWRP setup and decided to try what N01tra user suggested.
It worked like a charm! Thanks again!
fourcc said:
Hey thierrybla, it worked beautifully! Thanks!
The only thing I did different is too install the prerooted image with Fastboot instead of the Oldroid Twrp.
I was afraid of messing my good working TWRP setup and decided to try what N01tra user suggested.
It worked like a charm! Thanks again!
Click to expand...
Click to collapse
that's fine too I'm glad it worked good for you!
Have a nice day!
I got a brand new Samsung Tab E 9.6" (SM-T560). Shame on me, I didn't notice before it comes with Android 4.4.4
As many apps require newer OS, I'm wondering if I can upgrade it to Android 6.0.
Plase note:
1. I'm not an expert, so please explain me as easy as possible how to do it, if it can be done;
2. please tell me, in case,if it's 100% legal and/or if it can void warrant.
Thank you.
Samsung Tab E
Check again --- Just picked up the same thing this week at Walmart for $129.00 + $25 Google Play credits - it came with 7.1.1. - Take it back sounds like you got some real old stock..
They do come with Android 4.4, however if you go to Samsungs web page you can find a crispy 7.1.1 image you can flash with Odin. Then if you wish you can unlock bootloader and flash a custom recovery like CWM or TWRP and then chainfires systemless root. Cheers! Upgrading to just 7.1.1 with Odin will not void your warranty, anything else that involves unlocking the bootloader will and is will trip samsungs knox security feature. If warranty is important only flash the 7.1.1 image using Odin.
Hello,
I'm searching forsuch an update, too. But It seems, that it was only released for USA and CA. But I'm from Germany. @xSLAYERx do you have a link to the ROM?
xSLAYERx said:
They do come with Android 4.4, however if you go to Samsungs web page you can find a crispy 7.1.1 image you can flash with Odin. Then if you wish you can unlock bootloader and flash a custom recovery like CWM or TWRP and then chainfires systemless root. Cheers! Upgrading to just 7.1.1 with Odin will not void your warranty, anything else that involves unlocking the bootloader will and is will trip samsungs knox security feature. If warranty is important only flash the 7.1.1 image using Odin.
Click to expand...
Click to collapse
heya, could you please share a link of this 7.1.1 with me? or the image itself, I can't find it anywhere and I'm stuck with 4.4.4
thank you!
hurkagyurka123 said:
heya, could you please share a link of this 7.1.1 with me? or the image itself, I can't find it anywhere and I'm stuck with 4.4.4
thank you!
Click to expand...
Click to collapse
Hi, I was with the same problem, and I posted here in XDA, I'm from Brazil, i have the model SM-T560, and now i'm using nougt, from Lineageos 14.1, and this was only possible, because someone from Xda, gave me the following link:
http://www.gearappsnap.com/2018/03/14/how-to-install-android-nougat-on-the-galaxy-tab-e-sm-t561/
The rom is of the SM-T561 model, but also works on the SM-T560, read everything before doing anything. When installing TWRP, you can install the version of the SM-t560, which will not make any difference.
One more thing, I advise you to see some YouTube tutorials how to install TWRP. Just in case.
Thank You for your help!
hurkagyurka123 said:
Thank You for your help!
Click to expand...
Click to collapse
For nothing, follow step by step that will work perfectly. Except this will end your warranty, but it's the only way to install an update. If you need any help, just talk.
gearappsnap site is not really good made.. The download links behind text which look like a normal one and also that it says, flash boot.img only when the memory is wrong..
Well, CM14.1 did not work for me.. I had to flash boot.img before EVERYTHING else, then rebooted again to TWRP and THEN install cm14.1.
Um, did you follow step by step?
I followed what was written, and for me it worked normal, The boot.img file is to fit just the memory of the table because it had some problem with the rom, without installing it, has tablet that got locked in infinite loop. And the links were working normal for me.
Links that i download:
ROM: https://drive.google.com/file/d/1D0wrGM4XyZMo-t3ll4trvJ93Pl1KEZ1V/view
Boot.img: https://drive.google.com/file/d/1bqGmu4NTlEeKdsFPGjIY9lnPqujjazr4/view
softkeys: https://drive.google.com/file/d/1ddSB28g1xTd0J7sl8V6QmlPZA1aX77ot/view
Gaps: https://opengapps.org/
First the TWRP is installed, with the battery above 70%, then restarts the tablet.
Within the TWRP:
1) Wibe-> advanced wibe-> selects almost anything but not microSD and OTC. and Wibe.
2) Back to the home page-> Install-> select the external storage (the files must be saved on the SD card).
3) The first file to be installed is the rom.
4) Once installed, go back to the files and at the bottom of the page you will click install image and install boot.img.
5) After Boot.img is installed, switch back to Install Zip, and Install the Softkeys.
6) After installing the softkeys go back and install the Gaps. (I used the ARM-7.1-Pico) and restart the tablet.
In my case I did not install superSU. That's what I did. This rom has some flaws but better than Kitkat, that's what I think.
thE_29 said:
gearappsnap site is not really good made.. The download links behind text which look like a normal one and also that it says, flash boot.img only when the memory is wrong..
Well, CM14.1 did not work for me.. I had to flash boot.img before EVERYTHING else, then rebooted again to TWRP and THEN install cm14.1.
Click to expand...
Click to collapse
HEY!
download this: https://mega.nz/#!yEpjCITA!9EA101hYDOajDwmBHKxSZhv3QkV-RI61MkLn0JYNRZY
unzip and install and follow steps.
1-install TWRP 3.0.2-1 via odin
2- copy ALL files of .zip in one folder in storage (mem stick)
3- power off and then power on IN TWRP (vol + + home + power button)
4- make full wipes except externar storage
5- install zip (first choice lineage -14, then choice open gapps, next choice key.zip)
6- install img (choice boot.img)
7- WIPE (Dalvik, cache)
enjoy android 7.1 in your tab e T560
63or63 said:
HEY!
download this: https://mega.nz/#!yEpjCITA!9EA101hYDOajDwmBHKxSZhv3QkV-RI61MkLn0JYNRZY
unzip and install and follow steps.
1-install TWRP 3.0.2-1 via odin
2- copy ALL files of .zip in one folder in storage (mem stick)
3- power off and then power on IN TWRP (vol + + home + power button)
4- make full wipes except externar storage
5- install zip (first choice lineage -14, then choice open gapps, next choice key.zip)
6- install img (choice boot.img)
7- WIPE (Dalvik, cache)
enjoy android 7.1 in your tab e T560
Click to expand...
Click to collapse
In reality you have to install boot.img and softkeys before, the reason is because they are modified for the T56X, otherwise install themselves after the gaps will give error when to use. At least it is what was written on the site, and so far I have been using no defect at all.
marcelo010 said:
In reality you have to install boot.img and softkeys before, the reason is because they are modified for the T56X, otherwise install themselves after the gaps will give error when to use. At least it is what was written on the site, and so far I have been using no defect at all.
Click to expand...
Click to collapse
I do not think that is effective. if you come from 4.4.4 and install it before the lineage ROM (BASE 7.1 for example) it will be erased again because with the new base everything is overwritten.
63or63 said:
I do not think that is effective. if you come from 4.4.4 and install it before the lineage ROM (BASE 7.1 for example) it will be erased again because with the new base everything is overwritten.
Click to expand...
Click to collapse
Well that didnt work for me.. Was coming from Stock 4.4 ROM. Flashed the CM14.1 AND softkeys, but NOT the boot.img, because you cannot flash zip and img files at the same time. Then I booted it and it crashed 10-60secs after it booted. Sometimes it had a boot loop.
Then I tried CM 13 which worked fine and in a german board, someone wrote (based on the gearappsnap site) that the boot.img has to be the first thing to flash and even reboot into twrp again and then flash CM14.1 + softkeys + gapps.
If you could install it, that's what matters, in my case it worked the way it was on the site, there are some bug's, but it's a lot better than the stock rom, and I was already using a custom rom on the T560 before installing this LineageOS 14.1,and it was this link:
https://forum.xda-developers.com/galaxy-tab-e/development/rom-lightning-t3716039
Szia!
did the upgrade work for You For galaxy tab e?
Done this and it worked but.........
The tablet is really slow, not netflix compatible with this version, and so on....
I think I just might downgrade again
After I have tried step 3, it didnt open in twrp mode. My tab stucks in black screen with "Samsung galaxt tab e " text in background.Please let me know how to proceed.
[QUOTE = "63or63, Post: 78613279, Mitglied: 4438103"]
HI THERE!
Download this: https://mega.nz/#!yEpjCITA!9EA101hYDOajDwmBHKxSZhv3QkV-RI61MkLn0JYNRZY
unzip and install and follow the steps.
1-install TWRP 3.0.2-1 through odin
2- Copy ALL .zip files to a folder in memory (mem stick).
3- turn off and then turn on IN TWRP (vol + + home + power button)
4- Make full towels except for external storage
5- install zip (first choice line -14, then select open gaps, next choice key.zip)
6- install img (choose boot.img)
7- WIPE (Dalvik, Cache)
enjoy Android 7.1 in your Tab e T560
[/ZITAT]
1000 tanks BR
.
1000 x danke es hat funktioniert
Translation: 1000 x thank you it worked