Hi,
after the lollipop update the phone worked for a few days, then got in a boot loop.
recovery booting
recovery is not seandroid enforcing
set warranty bit recovery
what i already have done:
flashing several roms, no succes
no way to get in recovery mode with the buttons, flashing cwm and twrp without succes
i dont know exactly wich rom i need because i dont know the csc, the phone comes from groupon, i just know that if i have to send it to repair, i have to send it to spain.
i'm from belgium and the phone worked good before the update.
what can i do more to get it back to work?
thnx
When flashing, are you doing a factory reset before each flash attempt? Are you flashing a GApps after the ROM?
duckredbeard said:
When flashing, are you doing a factory reset before each flash attempt? Are you flashing a GApps after the ROM?
Click to expand...
Click to collapse
no, it is not possible doing factory reset, because i cant turn the phone on and cant get in to recovery.
i do not flash GApps after.
You said you're not able to enter recovery. Are you able to enter download mode by pressing and holding volume down, home, and power? If you are able to do so, tell us your carrier, as you're already mentioned what country you're in as well as the phone model.
Strephon Alkhalikoi said:
You said you're not able to enter recovery. Are you able to enter download mode by pressing and holding volume down, home, and power? If you are able to do so, tell us your carrier, as you're already mentioned what country you're in as well as the phone model.
Click to expand...
Click to collapse
download mode is no problem, my carrier is telenet.
Belgium doesn't have its own CSC codes, so use the unbranded German firmware found here (yes it will work) to restore your S4 to stock. After that, run with the stock ROM for a little while to make sure everything is fine, then root and install a custom ROM.
Strephon Alkhalikoi said:
Belgium doesn't have its own CSC codes, so use the unbranded German firmware found here (yes it will work) to restore your S4 to stock. After that, run with the stock ROM for a little while to make sure everything is fine, then root and install a custom ROM.
Click to expand...
Click to collapse
i flashed the german ffirmware without results
Were you able to get into the stock recovery after flashing the ROM?
no way to get in recovery. flashing the rom gives a pass, butt no recovery.
Are you using the original cable and not using a USB hub? If you are using a hub, disconnect from the hub and plug into an available USB port. If not using a hub, change ports and try again. Flashing a ROM should have cured all ills.
Strephon Alkhalikoi said:
Are you using the original cable and not using a USB hub? If you are using a hub, disconnect from the hub and plug into an available USB port. If not using a hub, change ports and try again. Flashing a ROM should have cured all ills.
Click to expand...
Click to collapse
i'm using the cable from my S3 and no USB hub, directly into the USB port, flash result is pass and reset but no way to get in that recovery or no normal startup.
And did you change ports as I recommended?
If you can't get it working after changing ports and trying to install, look for the I9505 PIT file and use it with the ROM. The PIT file will wipe the internal storage and ensure it's configured the way Samsung wants it. If you still get no results after this, you'll have to take the phone to the repair center.
oké, that's what i thought, thanks for your help.
When we say don't use a usb hub, we really want you to avoid usb expansion cards also. You should be going directly into a usb port of the motherboard. Some people recommend disconnecting other usb devices such as external drives and hubs. My gs4 has touch screen issues when I plug it into a usb port that isn't a motherboard port.
Related
Im sure you all have heard this one before. But I think mine may be alittle different. Im getting the error, System software not authorized etc. I bought it off of someone. I have odin 3.07 and it doesnt show the COM ports. I got USB drivers for samsung cellphones. I also got the stock ROM downloaded. I guess the question is, is there a way to flash this back to stock from the SD Card? I noticed this. I unplug the USB cable. The phone turns off. It does not come on unless the USB cable is hooked up. So I dont know if this means anything different. This phone has never been hooked up to this computer. It shows a Unknown Device in my device manager. Its hardware ID tag is USB\UNKNOWN. It is showing the SECURE FAIL: KERNAL. Can someone point me in the corrrect direction. Any help would be greatly appreciated.
VaRMiT said:
Im sure you all have heard this one before. But I think mine may be alittle different. Im getting the error, System software not authorized etc. I bought it off of someone. I have odin 3.07 and it doesnt show the COM ports. I got USB drivers for samsung cellphones. I also got the stock ROM downloaded. I guess the question is, is there a way to flash this back to stock from the SD Card? I noticed this. I unplug the USB cable. The phone turns off. It does not come on unless the USB cable is hooked up. So I dont know if this means anything different. This phone has never been hooked up to this computer. It shows a Unknown Device in my device manager. Its hardware ID tag is USB\UNKNOWN. It is showing the SECURE FAIL: KERNAL. Can someone point me in the corrrect direction. Any help would be greatly appreciated.
Click to expand...
Click to collapse
I'm guessing you when you bought it the phone booted is this correct?
If yes, what firmware is on it?
What have you done that no longer allows the phone the boot (did you flash something with Odin)?
The more info the better....
rayburne said:
I'm guessing you when you bought it the phone booted is this correct?
If yes, what firmware is on it?
What have you done that no longer allows the phone the boot (did you flash something with Odin)?
The more info the better....
Click to expand...
Click to collapse
Ive done nothing. I can get it to the POWER, VOL DOWN, HOME BUTTON and it shows the droid Downloading .....
I have no clue what firmware is on it.
VaRMiT said:
Ive done nothing. I can get it to the POWER, VOL DOWN, HOME BUTTON and it shows the droid Downloading .....
I have no clue what firmware is on it.
Click to expand...
Click to collapse
So you bought the phone and it has never booted for you?
If you have MF3 bootloader on there and someone tried to install a custom recovery it could be soft bricked.
Not sure what to suggest if you don't know what occurred to cause the phone to only go into download mode?
You could take it to best buy with a samsung experience center and have them reflash it?
The only problem with this is if you don't have MF3 bootloader, best buy will flash it and upgrade it.....
Try to Odin MDL on it first
Sent from my SGH-I337 using Tapatalk
rushi.1986 said:
Try to Odin MDL on it first
Sent from my SGH-I337 using Tapatalk
Click to expand...
Click to collapse
When you mean MDL. thats the stock rom correct? I do have that. When I look at Odin, it doesnt show anything on the COM part at the top left. Like its hooked up to a com port.
What I meant by the Downloading ...... (with the driod logo guy) Im saying I can get it to do that. Im at the point where I cant get the S4 to be reconized by ODIN. I have the stock rom, odin 3.07 files. I have tried to install the samsung usb drivers....
Still no reply on how to fix this? I have no clue on what to do here. I dont know what firmware etc is on it. I bought it this way. I just want to flash it back to factory, its the att version. It only stays on when the usb is hooked up. I can get it to go into download mode. But on the computer, it doesnt show a usb device being found. I can start odin up, but nothing appears on the COM to show what com port is available. Is there anything I can do here off of a SDCard? I also need to mention that I can not hold down vol up and power and home button to get it to go into recovery mode. It flashes it fast and goes to the yellow triangle.
Anyone please.....
You need to get Odin to recognize it. Try different usb cables. Use the usb ports on the back of the computer. Try a different computer. Without knowing the firmware you're on odin may not work, but it should still recognize your device. If you're on mdl firmware Odin will work. If you're on mf3 then you're sol.
Have you tried to get into the recovery and not just the download mode?
Volume up + Home + Power - If you can get into a recovery try to do a factory reset.
If you cant get into the recovery than you'll need Odin. Sometimes (rarely) kies well affect Odin. If you have kies uninstall it and than run odin.
- Open Odin without your phone connected.
- Power on your device, go into download (Odin) mode. Volume down + home + power.
- Now plug device into your computer.
- Odin should read it, unless its MF3 firmwire.
If your phone is MF3, you may need a Samsung bestbuy rep to reflash the mf3 firmwire.
Sent from my SGH-I337 using XDA Premium 4 mobile app
Br4nd3n said:
Have you tried to get into the recovery and not just the download mode?
Volume up + Home + Power - If you can get into a recovery try to do a factory reset.
If you cant get into the recovery than you'll need Odin. Sometimes (rarely) kies well affect Odin. If you have kies uninstall it and than run odin.
- Open Odin without your phone connected.
- Power on your device, go into download (Odin) mode. Volume down + home + power.
- Now plug device into your computer.
- Odin should read it, unless its MF3 firmwire.
If your phone is MF3, you may need a Samsung bestbuy rep to reflash the mf3 firmwire.
Sent from my SGH-I337 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I have tried the power, vol up and home. It flashes the recovery, then goes back to the triangle. Odin, doesnt show a COM port that the phone is connected when i have it in download mode.
Also....i do appreciate you all for helping me figure this out.
hi
first i know its anoying when people opened a new threads with the same questions but this is the only way that people will realy answer back....
i have a galaxy s4 i9505 (jflte) international 4.4.2 rooted. i replace my cwm with philz and i wanted to rebot my phone so i did it and when i reboot the phone didnt wake up it get stuck every time.i serched all over the internet for guides and nothing helped.
1. i tried to get into safe mode but nothing happend it still get stuck on the logo.
2. i tried all kind of reset things in philz (factory reset,wipe cache,wipe davlik cache,clean to install new rom,wipe use media,everythng!!!!!!!)
3. i tried to pull out the battery and the sd card.
if anyone can help me fast i will thank him a lot!!!!!
sorry for the bad english.
Are you able to get into download mode (press and hold Volume -, Home, and Power)? If so, head over to sammobile.com or samsung-updates.com and download the latest ROM for your device. To know which ROM to get, you need to know what carrier you are using and the model of the S4. Once the ROM is downloaded, install it via Odin to stop your bootloop. Afterwards, root, then install TWRP 2.8.6.0. Do not install Philz as that recovery is no longer being developed, and may not function correctly with Android 5.0.1 or later.
Strephon Alkhalikoi said:
Are you able to get into download mode (press and hold Volume -, Home, and Power)? If so, head over to sammobile.com or samsung-updates.com and download the latest ROM for your device. To know which ROM to get, you need to know what carrier you are using and the model of the S4. Once the ROM is downloaded, install it via Odin to stop your bootloop. Afterwards, root, then install TWRP 2.8.6.0. Do not install Philz as that recovery is no longer being developed, and may not function correctly with Android 5.0.1 or later.
Click to expand...
Click to collapse
yes i can get into download mode but i have some problemes :
1) odin always crash on my pc it happens every time i connect everything as i need to and then when i click start it crash and i dont know why i tried to serch via web but.... nothing.
2) i dont know realy what is my model the only thing that i know is : galaxy s4 i9505 is there any way i can know without looking inside the phone in setting.
thank you for everthing!!!
For Odin, try a different port on your PC, always use the original USB cable whenever possible, and make sure Kies isn't installed or if installed, isn't running. Try a different PC if necessary.
Regarding your S4, is it unlocked? If not, what carrier are you using, and what country are you located in?
Ok...
Somehow i managed to reach a point where my device does not boot when i press the power botton...
Unless i connect it to a usb or a power and then it starts and even goes to the android but loops...
If i disconnect it from the cable it just dies...
Any ideas?
10xs.
mirzanoshin said:
Which model of phone you are using?
Click to expand...
Click to collapse
S4 galaxy i9500
Yes... It happened after i tried to update a firmware to lollilop...
After it happened i tried to fix PIT with a stock rom...
Now it turns on while connected to a usb shows the galxy logo and then reboots...
If disconnected from usb or power it just dies...
I can access download mode and cwm while connected to usb.
At some moments it even reaches the android system and tries booting but then goes to a reboot loop again.
JacobTodoit said:
Ok...
Somehow i managed to reach a point where my device does not boot when i press the power botton...
Unless i connect it to a usb or a power and then it starts and even goes to the android but loops...
If i disconnect it from the cable it just dies...
Any ideas?
10xs.
Click to expand...
Click to collapse
Greetings,
Thank you for using XDA Assist. Please provide your device make and model so I can guide you to the correct information and help you need.
Thank you.
What problem did the phone have that prompted you to flash the phone?
Did you perform a factory wipe in stock recovery before booting the newly-flashed stock rom for the first time?
The original problem was that all processes started halting...
I did the wipe to lollilop and then installed a rom... That is when tthe device bricked.
Later i downloaded a firmware which was supposed to be stock firmware and tried flashing it but it didn't help.
No matter what i try it keeps looping without the ability to power on without a usb connection being plugged (pc or power).
I am looking for an original firmware which would contain the files for the bbotloader and other in order to flash again...
Will appreciate any help.
The device was bought in Israel.
Did you try flashing a stock ROM with a pit file?
Hi and thank u for your response.
As far as i know it os a galaxy s4,
Gt-I9500 bought on Israel. Was running the cellphone company' stock version 5.0.1 with base version i9500xxuhhog1.
It started doing some problems after it was lost and found.
The cell company bllocked it and we had to replace the imei.
Then every process we tried to work with, halted.
So we decided to flash a new version and new firmware.
We tried moving to lollilop and cm12 but the dvices got to the point where it is now.
I am sure it is something we did with odin...
But not sure what.
Now the situation is as follows.
The device doesn't boot when pressing on the power button.
For booting we need to plug it to a usb power supply or pc and just go to recovery.
From there we choose the option of reboot system and it boots, but keeps looping.
If at any moment we unplug the ub connection it dies.
Following to some advises i tried getting the stock rom online and found a version i9500xxuhog1.
And a pit file.
I applied them to the device, though nothong changed.
10xs for any help.
Jacob
The_Merovingian said:
Greetings,
Thank you for using XDA Assist. Please provide your device make and model so I can guide you to the correct information and help you need.
Thank you.
Click to expand...
Click to collapse
audit13 said:
Did you try flashing a stock ROM with a pit file?
Click to expand...
Click to collapse
Yes... Several times.
With several different firmwares.
So Odin never finished flashing a stock rom?
You may have to use a jtag service to repair the phone.
Hi!
I have a Samsung Galaxy S4 i9505, which is not booting anymore after I tried to change the sim card tray. It gets stuck on the Samsung logo at boot. Recovery won't boot either. (says recovery booting but does not boot) I can only get it to download mode. I tried reflashing recovery with heimdall. Is there any way to recover data or fix the phone? I know it could be a hardware fault that's practically impossible to fix. Strange symptoms for a hardware fault though. Just looking for any ideas. It would be nice to at least dump data from it or get recovery booting.
Thank you for your help!
Try a different bootloader.
Or flash another rom with Odin.
GDReaper said:
Try a different bootloader.
Or flash another rom with Odin.
Click to expand...
Click to collapse
Where can I find a bootloader to install? I tried googling a bit but couldn't find a clear answer. Do the modem files also have the bootloader, should I flash a new modem file?
Modem and bootloader are different files.
You can find modems and bootloaders this thread. You may have to scroll through the comments to find what you're looking for.
GDReaper said:
Modem and bootloader are different files.
You can find modems and bootloaders this thread. You may have to scroll through the comments to find what you're looking for.
Click to expand...
Click to collapse
Tried flashing a new bootloader. Now I get a message that "Recovery is not seandroid enforcing" It still does not boot into TWRP recovery. I tried flashing another version of TWRP, but no difference.
Try this:
Open Odin, uncheck everything except f.reset time, flash TWRP, when you see the word "reset" in the status window, remove USB cable, remove battery, wait 5 seconds, replace battery, use button combination to boot into recovery. When the phone starts to boot, release the power button but keep holding the volume up and home.
audit13 said:
Try this:
Open Odin, uncheck everything except f.reset time, flash TWRP, when you see the word "reset" in the status window, remove USB cable, remove battery, wait 5 seconds, replace battery, use button combination to boot into recovery. When the phone starts to boot, release the power button but keep holding the volume up and home.
Click to expand...
Click to collapse
Which version of odin would you suggest me to use? I tried with 1.85 and that didn't help. I'm starting to think that this might be a hardware fault, perhaps I broke something when tearing off the old sim card tray. Or the new part was faulty and somehow fried my phone. I have a backup from about a month ago. It was stupid not to take a backup before attempting to replace the sim card tray, but I tought it wouldn't be so dangerous.
Its not hardware problem. Hoy have a bootloop and Thats software problem. If you had stock recovery then the cause of bootloop also broken your recovery mode.
You will have to flash a full stock rom (Sam mobile web has them) or search here on xda.
A full stock rom has updated bootloader and módem, also stock recovery built in.
BraianV said:
Its not hardware problem. Hoy have a bootloop and Thats software problem. If you had stock recovery then the cause of bootloop also broken your recovery mode.
You will have to flash a full stock rom (Sam mobile web has them) or search here on xda.
A full stock rom has updated bootloader and módem, also stock recovery built in.
Click to expand...
Click to collapse
That also means losing all my data if I can't boot recovery beforehand. But perhaps I have to try that.
If you had usb debugging enabled you might be able to pull the data from the phone.
Odin 1.85 seems really old. I mean really old. You should use Odin 3.x. I had success with Odin 3.09 in the past.
GDReaper said:
If you had usb debugging enabled you might be able to pull the data from the phone.
Odin 1.85 seems really old. I mean really old. You should use Odin 3.x. I had success with Odin 3.09 in the past.
Click to expand...
Click to collapse
Would it be enough if I flashed just stock recovery+modem+bootloader or something like that? I had usb debugging enabled, but since I cant get the system to boot at all it's of no use.
Can I use adb in stock recovery? I think the stock rom won't boot with my current data still on the device. I had cyanogenmod 12.1 installed. Haven't had stock rom in ages.
Ilumod said:
Which version of odin would you suggest me to use? I tried with 1.85 and that didn't help. I'm starting to think that this might be a hardware fault, perhaps I broke something when tearing off the old sim card tray. Or the new part was faulty and somehow fried my phone. I have a backup from about a month ago. It was stupid not to take a backup before attempting to replace the sim card tray, but I tought it wouldn't be so dangerous.
Click to expand...
Click to collapse
I prefer Odin 3.07 for all of my flashing needs. I have used it on a note 2, note 3, s4, s3, and s2.
If the flash fails, try different USB cables and different USB ports.
I just bought a BNIB Note 3.
Samsung Note 3: SM-N900W8
Symptoms: Won't turn on, no lights, no load screen, no recovery mode, no download mode.
When I hook the phone up to the PC via USB it does vibrate and sounds the connection ringtone
What I was doing when this happened:
I had just recently rooted using "KINGRoot" - checked root and it was successful
I installed "TWRP" and booted into recovery mode and it was a success as well(I didn't actually run here yet)
***I installed and opened "Flashfire" to Flash the LINEAGE OS to my Rom buuut I didn't actually select the Lineage pack and I accidently pressed FLash(insert expletive here) *****
So Flashfire went through it's loading and when it was done it shut off and then the symptoms started.
It's a Note3 from Bell with all of their bloatware on it and I wanted to clean it all off and run a clean/efficient Note 3 cell with Rogers. I'm not looking to keep any of the data currently on the phone as there isn't anything currently on it. I just want to be able to install Lineage and use my Note.
I've searched for 30 hours pretty solid so far and unfortunately I haven't come across a clear solution. Can anyone give me a diagnosis and a tutorial or a link to a fix.
I'm open to loading from MicroSD, USB Jig, Samsung Kies....anymore information you require from me as away and I'll get back ASAP
Dead battery would be first check .
JJEgan said:
Dead battery would be first check .
Click to expand...
Click to collapse
Battery - I did the "spin" test on the battery and it doesn't show any physical characteristics of an overheated(bulged) battery. I'm going to test fit my battery into another note3 and I'll respond asap.
JJEgan said:
Dead battery would be first check .
Click to expand...
Click to collapse
I tried the battery in another Note3 and my battery is 52% charged and had no issues booting the tester phone.
I have the phone being tested for any Hardware issues right now.
If it's not a hardware issue will I be able to force a Rom(whether OEM Firmware or other) to install via MicroSD or USB jig?
When the phone is connected to a Windows machine, does a new device appear in device manager?
Have you tried to force it into download mode with a USB jig?
For flashing ROMs to the sm-n900w8, the simplest method is to flash TWRP, boot to TWRP, wipe everything, and flash the desired ROM.
If nothing works, you could take it to a cell repair shop and hopefully have it repaired with a jtag cable or a similar method.
audit13 said:
When the phone is connected to a Windows machine, does a new device appear in device manager?
Have you tried to force it into download mode with a USB jig?
For flashing ROMs to the sm-n900w8, the simplest method is to flash TWRP, boot to TWRP, wipe everything, and flash the desired ROM.
If nothing works, you could take it to a cell repair shop and hopefully have it repaired with a jtag cable or a similar method.
Click to expand...
Click to collapse
No, the PC doesn't see the phone.
The USB jig or MicroSD force is something I'm researching to try next(feel free to provide any good links to set up a jig(I've done this with Ubuntu on my laptop but this has a more intimidating feel to it)). The Tech at the shop I took it to test the hardware says "the motherboard" is broken and he'll fix it for $60.
For future considerations I'll learn to use TWRP flashing ROMs.
If the shop is offering to fix it for $60, they may be just force-flashing the firmware with something like an Octopusbox.
The USB jig may force the phone into download. If it doesn't, I don't think you'll have a choice but to pay to have it flashed. Unfortunately, Samsung will not help as rooting would trip the knox counter.
USB jig ebay are the usual cheap source.