Related
Hy there, Yesterday, I made Nexus with factory fireware with Clockwork mode. This one: http://forum.xda-developers.com/showthread.php?t=1061855
because back there I had Cyannoge mode 7. It didn't want to reset factory options with mobile phone so, I must do on that way.... I made everything good like it writes in instructions in first post and it didn't show up any errors. On the end when I finished it and pushed the REBOOT button, I pushed it and it didn't worked at all anymore... Temperature of battery was ok, and battery life 30%... I tried to let it turned on, and check it in the morning. It didn't showed up any contact, and put it in recovery that I can HOLD the Volumen UP Button and Power up Button but, again nothing. I tried to get out te Card and Batery about 30mins and then put it back inside but it didn't worked again. Now I tried to put it on USB, i thought that somekind of contact will show up but nothing.
I'm going to go out on a limb and guess you don't have an i9020T. In fact I'm willing to bet you have an i9023. Therefore you just flashed firmware for another phone. If my above prediction is correct you have a different screen type which is not supported by this firmware. Does your computer recognize the phone? adb devices or fastboot devices if you try to power into the boot loader?
Sent from my Nexus S 4G using xda premium
yes its i9023 :S ..
Does your computer recognize the phone - no
adb devices or fastboot devices if you try to power into the boot loader? - with pressing volumen up and power button or what?
i am new , i dont now using adb ..
download mode dont working :S
a try this http://forum.xda-developers.com/showthread.php?t=1397393 and this http://forum.xda-developers.com/showpost.php?p=20382688&postcount=16 tuturial but dont working download mode..
how to fix it ?
Hi!
Downloading ... mode, be sure it's working !
Just shut down your phone, pull out battery for 5 min.
Now connect USB cable , simultaneously ( press volume-up and volume-down and insert battery ) ...after a few seconds you will see on the device Downloading....and your PC will install the driver....Good luck !
---------- Post added at 08:18 PM ---------- Previous post was at 08:15 PM ----------
If your PC recognized your device in Downloading mode ....I can help you with Odin for reinstall .....
unbrick software must be on or ?
no STOP ! Just follow what I said....
---------- Post added at 08:28 PM ---------- Previous post was at 08:27 PM ----------
unbrick tools not work...don't try it !
---------- Post added at 08:32 PM ---------- Previous post was at 08:28 PM ----------
Tell me if you see Downloading... on your device screen ?
---------- Post added at 08:41 PM ---------- Previous post was at 08:32 PM ----------
You can try Odin if you can entry in Downloading mode ...it's very easy ....
surdu_petru;20945733 pull out battery for 5 min.
Now connect USB cable said:
i dont see download mode , after this.. do you have nexus s ?
Click to expand...
Click to collapse
rabbitdix said:
i dont see download mode , after this.. do you have nexus s ?
Click to expand...
Click to collapse
Yes I have Nexus S - I9023
---------- Post added at 09:29 PM ---------- Previous post was at 09:24 PM ----------
rabbitdix said:
i dont see download mode , after this.. do you have nexus s ?
Click to expand...
Click to collapse
Impossible !
connect USB cable, after that press with the left hand volume-up and volume-down and don't release and now with the right hand insert the battery , you will see on the screen Downloading...
---------- Post added at 09:36 PM ---------- Previous post was at 09:29 PM ----------
Quick how to for odin:
You need samsung drivers installed
Files for european i9023 nexus s: http://www.multiupload.com/A6OP3TFN0I
I used odin v 1.83 (only this version worked for me) on windows. Order of files in odin:
- Bootloader > Bootloader_I9023XXKA3.tar.md5
- PDA > PDA_SOJU_GRI54_TMO_EUR_MR1_SIGNED.tar.md5
- PHONE > MODEM_I9023XXKB3_REV_00_CL912571_SIGNED.tar.md5
- CSC > DGS_I9023_EUR.tar
-download Odin : http://www.4shared.com/file/W0ky2Cg-/Odin3_v183.html
-Samsung USB drivers : http://www.4shared.com/zip/8jDrhLtc/SAMSUNG_USB_Driver.html
Good luck !
can i go to downlaod mode with Odin ?
rabbitdix said:
can i go to downlaod mode with Odin ?
Click to expand...
Click to collapse
Yes, first you must entery into Download mode....after that open Odin....
---------- Post added at 10:32 PM ---------- Previous post was at 10:31 PM ----------
WHY it's so compliccated for you ????
---------- Post added at 10:33 PM ---------- Previous post was at 10:32 PM ----------
WHAT you don't understand ?
dont working download mode..
What does not work?? What do you see on the screen, what does the device? Give him some information, hes trying to help your device. He is not earning anything with it... So say what you see, what you do all stuff.
He could stop helping you because you didn't gave any information... Then your stuck with this state of your phone, so give information about what you see and do...
If you give the info you could maybe earlier use your phone.
nothing, the screen is black ..
rabbitdix said:
nothing, the screen is black ..
Click to expand...
Click to collapse
Ok, now if you connect USB cable, can you see on the screen a pict. with battery is charging ?
---------- Post added at 11:17 PM ---------- Previous post was at 11:07 PM ----------
If you don't see on the screen battery is charging when you connect your device at the USB cable ( or power supply)... you have to go with him to a repair center !
AND If you CAN see on the screen the battery charging logo when you connect your device at the USB cable , than follows well what is written above ! Good luck and open your eyes !
no , nothing . how much money does a repair ?
rabbitdix said:
no , nothing . how much money does a repair ?
If the phone is in warranty period , then they will repair for free !
---------- Post added at 11:32 PM ---------- Previous post was at 11:24 PM ----------
Take a look : http://forum.xda-developers.com/showthread.php?t=1360146
It's FREE ....
Click to expand...
Click to collapse
do not really understand English.. just a little
Okay so my phone was rooted, I unrooted it successfully and flashed a stock ROM. Just as I was about to sell the phone as now have galaxy s5 the phone said it needed an update (official Samsung) so I let it do its thing but when the update completed the phone screen went black and did not come back on and since then the phone shows no signs of life what so ever.
After a bit of research I have found out that this is a corrupt boot loader and there is a way to fix it ( the phone is an s4 i9505) this is done by using a piece of software but my problem is I cannot get the software to recognise the phone
I have tried to install the qualcomm drivers with some success in command prompt but I can still not get my computer to successfully install them as the phone is not showing up in the software.
When connecting to the computer I do hear the 'd don' sound showing that the phone is being recognised and the computer attempts to install the windows drivers (using windows 7) but always fails
Any help would be appreciated
Thanks alot
i rule123 said:
Okay so my phone was rooted, I unrooted it successfully and flashed a stock ROM. Just as I was about to sell the phone as now have galaxy s5 the phone said it needed an update (official Samsung) so I let it do its thing but when the update completed the phone screen went black and did not come back on and since then the phone shows no signs of life what so ever.
After a bit of research I have found out that this is a corrupt boot loader and there is a way to fix it ( the phone is an s4 i9505) this is done by using a piece of software but my problem is I cannot get the software to recognise the phone
I have tried to install the qualcomm drivers with some success in command prompt but I can still not get my computer to successfully install them as the phone is not showing up in the software.
When connecting to the computer I do hear the 'd don' sound showing that the phone is being recognised and the computer attempts to install the windows drivers (using windows 7) but always fails
Any help would be appreciated
Thanks alot
Click to expand...
Click to collapse
open in system setting, hardware devices.
if you plug in your phone, you see for few seconds qualcomm qshub or so. then click it right and install the driver manually.
if you have open the properties Menue, you can work with.
konsolen said:
open in system setting, hardware devices.
if you plug in your phone, you see for few seconds qualcomm qshub or so. then click it right and install the driver manually.
if you have open the properties Menue, you can work with.
Click to expand...
Click to collapse
I have tried this method and I can navigate to the driver but when installing I get a message saying that windows cannot install
qualcomm bootmode is very easy to repair.
But only if you know what you must do exactly.
I played with a dead sony sp 6 months, after i get it back to life from qualcomm mode.
now i waked up many sony and samsung from qualcomm boot mode.
if you install the correct driver, i can send you a repair tool.
---------- Post added at 04:19 PM ---------- Previous post was at 04:16 PM ----------
i rule123 said:
I have tried this method and I can navigate to the driver but when installing I get a message saying that windows cannot install
Click to expand...
Click to collapse
then you have the wrong driver. which one you installed?
there are for 32 and 64 bit windows. for qualcomm usb mode and also other qualcomm modes.
konsolen said:
qualcomm bootmode is very easy to repair.
But only if you know what you must do exactly.
I played with a dead sony sp 6 months, after i get it back to life from qualcomm mode.
now i waked up many sony and samsung from qualcomm boot mode.
if you install the correct driver, i can send you a repair tool.
---------- Post added at 04:19 PM ---------- Previous post was at 04:16 PM ----------
then you have the wrong driver. which one you installed?
there are for 32 and 64 bit windows. for qualcomm usb mode and also other qualcomm modes.
Click to expand...
Click to collapse
Thanks for the reply, I have a 64bit computer so tried all the 64 bit drivers, I installed all 4 .inf driver successfully in command prompt but when I plug the phone in windows attempts to install drivers and fails?
Do you have the drivers I need?
I also added the Microsoft certificates before hand aswell
Facing a similar problem.
Following.
what you need to know is, that your phone is not off. Also if no device is in device manager.
than the phone is in qualcoom download mode and wait for writing.
i look for the right drivers.mom.
Qualcomm HS-USB QDLoader 9008 this number?
---------- Post added at 04:53 PM ---------- Previous post was at 04:45 PM ----------
i found your driver pack my friend.
no worry, you wake this phone up today.
---------- Post added at 04:58 PM ---------- Previous post was at 04:53 PM ----------
https://mega.co.nz/#F!Vpl3xabT!Arcl1YvRDMXOT3O3VGTe-A
the driver pack and the jig tool. with that you can put phone in download mode.
---------- Post added at 05:09 PM ---------- Previous post was at 04:58 PM ----------
give me update pls. iam waiting for input.
konsolen said:
what you need to know is, that your phone is not off. Also if no device is in device manager.
than the phone is in qualcoom download mode and wait for writing.
i look for the right drivers.mom.
Qualcomm HS-USB QDLoader 9008 this number?
---------- Post added at 04:53 PM ---------- Previous post was at 04:45 PM ----------
i found your driver pack my friend.
no worry, you wake this phone up today.
---------- Post added at 04:58 PM ---------- Previous post was at 04:53 PM ----------
https://mega.co.nz/#F!Vpl3xabT!Arcl1YvRDMXOT3O3VGTe-A
the driver pack and the jig tool. with that you can put phone in download mode.
---------- Post added at 05:09 PM ---------- Previous post was at 04:58 PM ----------
give me update pls. iam waiting for input.
Click to expand...
Click to collapse
Okay thanks alot gonna try this pack now. thanks again ill let you know how it goes
konsolen said:
what you need to know is, that your phone is not off. Also if no device is in device manager.
than the phone is in qualcoom download mode and wait for writing.
i look for the right drivers.mom.
Qualcomm HS-USB QDLoader 9008 this number?
---------- Post added at 04:53 PM ---------- Previous post was at 04:45 PM ----------
i found your driver pack my friend.
no worry, you wake this phone up today.
---------- Post added at 04:58 PM ---------- Previous post was at 04:53 PM ----------
https://mega.co.nz/#F!Vpl3xabT!Arcl1YvRDMXOT3O3VGTe-A
the driver pack and the jig tool. with that you can put phone in download mode.
---------- Post added at 05:09 PM ---------- Previous post was at 04:58 PM ----------
give me update pls. iam waiting for input.
Click to expand...
Click to collapse
No luck still cant get drivers to install, i think this is something to do with my computer as i always seem to have trouble whenever i do anything on my mobile devices such as rooting and what not.
the driver file that doesnt seem to wanna go in is the 'qcser.inf' file.
How would you guys go about installing the driver as i am currently using the method shown in this thread: http://forum.xda-developers.com/showthread.php?t=1669498
I may have to give up soon as this is driving me up the wall lool
i rule123 said:
No luck still cant get drivers to install, i think this is something to do with my computer as i always seem to have trouble whenever i do anything on my mobile devices such as rooting and what not.
the driver file that doesnt seem to wanna go in is the 'qcser.inf' file.
How would you guys go about installing the driver as i am currently using the method shown in this thread: http://forum.xda-developers.com/showthread.php?t=1669498
I may have to give up soon as this is driving me up the wall lool
Click to expand...
Click to collapse
this install version is old my friend.It works with device manager. BUT....use a USB port that direct connect on your mainboard (no hub or USB 3.0), and youse the org. cabel. thats important.
You can also try the driver from the riffbox.they must also work.
---------- Post added at 11:49 AM ---------- Previous post was at 11:38 AM ----------
konsolen said:
this install version is old my friend.It works with device manager. BUT....use a USB port that direct connect on your mainboard (no hub or USB 3.0), and youse the org. cabel. thats important.
You can also try the driver from the riffbox.they must also work.
Click to expand...
Click to collapse
I load you up the chimera and the riffbox drivers..install it.
in device manager when your qualcomm pop up, click it and tick install driver manually.
then you must scroll down and choose the qualcomm.
Also upload a logfile from a i9505. So it looks like when repair is done
konsolen said:
this install version is old my friend.It works with device manager. BUT....use a USB port that direct connect on your mainboard (no hub or USB 3.0), and youse the org. cabel. thats important.
You can also try the driver from the riffbox.they must also work.
---------- Post added at 11:49 AM ---------- Previous post was at 11:38 AM ----------
I load you up the chimera and the riffbox drivers..install it.
in device manager when your qualcomm pop up, click it and tick install driver manually.
then you must scroll down and choose the qualcomm.
Also upload a logfile from a i9505. So it looks like when repair is done
Click to expand...
Click to collapse
I only used that method of installation, I didn't use the drivers from there, the drivers I used where from a forum thread which was specifically for the dead boot of a galaxy s4, this is also where I got the dead boot repair software from
How would you guys go about installing these drivers if you had t cause that must be where I'm going wrong or its just simply my stupid computer making everything difficult
I have the Same prop. Can anyone help?
Hello there. I think I've made something stupid, but dunno what.
Now I've a G2 with firmware update screen. But it doesn't say download mode at the beginning. vol+ and power throws me straight to the firmware mode. vol- and power (factory reset thing) does the same. No download mode, straight to the firmware. And also, my pc doesnt recognise the phone. Here's what I've done so far;
FLASH TOOL
I've downloaded and installed lg drivers, lots of them. (uninstalled and restarted my pc every time) My lg usb serial port with com41 is working but LGE Android MTP Device had yellow exclamation mark, always. Nonetheless I've tried. Changed the dlls, downloaded the correct tot file, changed the port to 41, replug the usb. Returns with 1 sec error, crossdl {rectangle} to D802 bla bla. No luck
LG MOBİLE SUPPORT TOOL
Found my phone. It said I've already latest software. (D802TR30C) I tried to upgrade recovery from the tool. Downloaded my software but it couldn' install to my phone because of unknown error. So, No luck again
LG FLASH TOOL 2014
I've downloaded the correct KDZ's. Installed my drivers. Started program with admin rights. Selected kdz and CSE flash. And then Start. Always stopped at %4 because of usb connection lost. No luck again and again
NOW I'M OUT OF IDEAS AN OPTIONS. PLEASE SOMEONE, HELP FOR GOD'S SAKE.
someone? anyone?
oblitus said:
someone? anyone?
Click to expand...
Click to collapse
Follow this link http://forum.xda-developers.com/lg-g2/general/lg-g2-unbrickable-fix-real-hard-brick-t2904404
---------- Post added at 03:34 PM ---------- Previous post was at 03:33 PM ----------
shubdya4u said:
Follow this link http://forum.xda-developers.com/lg-g2/general/lg-g2-unbrickable-fix-real-hard-brick-t2904404
Click to expand...
Click to collapse
I too similar problems but then this steps resolved it
H631 T-MOBILE UNBRICK GUIDE
So I recently bricked my phone trying to root it with MarshMallow 6.0 and wanted to make a guide on how I managed to unbrick for anyone with the same problem.
WARNING: ALL SETTING/APPS/FILES WILL BE LOST.
I was stuck in a bootloop and LG Bridge wasn't working with the phone to restore it.
REQUIRED ITEMS
1.) LG Flash Tool DOWNLOAD HERE
2.) LG Driver DOWNLOAD HERE
3.) Stock KDZ DOWNLOAD HERE (This will take you back to 5.1.1 stock)
1) Put your phone into Download Mode. To do this, hold the volume up key while plugging the phone into you computer. Don't let go of the volume up key until your in Download Mode and you see the screen where it says "Firmware Update"
2) Unzip LG FLash Tool and run as administrator. You shouldn't have to change any of your settings but it should read this:
"Select Type" - CDMA
"Phone Mode" - DIAG
"Reset Time" - 33000
Select the KDZ file you downloaded "H63110j_00.kdz"
4.) Click CSE Flash
5.) Click Start
6.) Don't change the Country or Language.
Click "Clear Phone Software Update Registry"
Click "OK"
Now click OK to start the installation.
7.) Then let the program run and it might say that it lost connection or timed out but just click ok
If you look down at your phone you will see the percentage increasing as the installation goes on.
Once the phone is done it will reboot. Unplug it as soon as it starts the reboot after installation.
Your phone should now be unbricked! :good:
Not sure how this works on Boost/Verizon/Sprint. If you download the proper KDZ it should all work the same.
MetroPCS KDZ File ( Thanks @GameTheory. )
LP 5.1.1 MS631v10d
http://csmgdl.lgmobile.com/dn/downlo...S63110d_00.kdz
LP 5.1.1 MS631v10i
http://csmgdl.lgmobile.com/dn/downlo...S63110i_00.kdz
LP 5.1.1 MS631v10j
http://csmgdl.lgmobile.com/dn/downlo...S63110j_00.kdz
-------------------------------------------------------------------------------------------------------------------------------
H636 Fido Variant v10i (Thanks @asidorowicz)
http://csmgdl.lgmobile.com/dn/downlo...H63610i_00.kdz
H636 Fido Variant v10k ( Thanks @fearhq )
http://csmgdl.lgmobile.com/dn/downlo...H63610k_00.kdz
Links provided by DrakenFX
My phone was bootlooping giving me the (modified!!) error after rooting 6.0, this guide brought it back. Thanks much!
stuck
It's been stuck on 51 % not sure if its because i clicked on the question markss from the lg thingy. everything was smooth but its been there for 20-25 min and it hasnt moved should i restart the whole thing or no ? im a super big beginner
---------- Post added at 01:58 AM ---------- Previous post was at 01:48 AM ----------
wooohooooo yassss, it worked ! thank you so much you were the only help on the internet
When I go to download the kdz it says not found. Can someone link me to another source?
Hello, It is easy to use LG UP to flash stock firmware on LG G stylo H631,
Unbrick H631 and bring back to stock.
http://www.mylgphones.com/t-mobile-lg-g-stylo-h631-how-to-unrick-restore-back-to-stock.html
---------- Post added at 04:25 AM ---------- Previous post was at 04:22 AM ----------
antoine66 said:
When I go to download the kdz it says not found. Can someone link me to another source?
Click to expand...
Click to collapse
Check http://csmg.lgmobile.com:9002/csmg/b2c/client/web_model_list.jsp?country=US
all devices listed supports web download, it means you can use lg bridge to upgrade your device, in another words, You can download kdz firmware with IMEI.
AT&T and Sprint now hosts LG firmware on their own servers. So all LG devices from ATT or Sprint supports FOTA Update only., We can not download kdz firmware with IMEI
I can't access Download mode, Recovery mode or fastboot mode by pressing the vol up key while plugging the device. It bricked after restarting the phone after rooting android v6.0 with kingroot. Now it will only go to the endless boot loop on the "Secure booting error Error 1003 MODIFIED". I have tried many many ways and read everything I have found on the subject from many forums and other similar cases on other devices but have not found a solution for the problem, I still can't get to any of the previous modes mentioned! Has anyone had the same issue and was able to fix it without sending it to LG or carrier warranty? If so can that person help me get my phone fixed please!?Thanks in advance.
---------- Post added at 11:14 PM ---------- Previous post was at 11:08 PM ----------
nelsonluna17 said:
I can't access Download mode, Recovery mode or fastboot mode by pressing the vol up key while plugging the device. It bricked after restarting the phone after rooting android v6.0 with kingroot. Now it will only go to the endless boot loop on the "Secure booting error Error 1003 MODIFIED". I have tried many many ways and read everything I have found on the subject from many forums and other similar cases on other devices but have not found a solution for the problem, I still can't get to any of the previous modes mentioned! Has anyone had the same issue and was able to fix it without sending it to LG or carrier warranty? If so can that person help me get my phone fixed please!?Thanks in advance.
Click to expand...
Click to collapse
Also When I connect the phone to PC it is not recognized, it shows as UNKNOWN on device manager. Using a windows 10 PC for all that I have tried.
Help me Please
Can you please check the download link for
H636 Fido Variant v10i
H636 Fido Variant v10k
Thank you
yswdk said:
Can you please check the download link for
H636 Fido Variant v10i
H636 Fido Variant v10k
Click to expand...
Click to collapse
http://lg-firmwares.com
Hi I just want to know if is there is any working link to download the kdz for LG style metro pcs mm..
antoine66 said:
When I go to download the kdz it says not found. Can someone link me to another source?
Click to expand...
Click to collapse
Try Androidhost. I Cant Post The Link Because Im New But You'll Find It There Just Add /GCrdw
Hi, I tried updating to the newest miui.eu release, sadly I couldn't charge my phone after I successfully updated. So I wiped the system to flash the rom I used beforehand. Sadly, now my whole partition couldn't be decrypted and I couldn't access it via USB. So after a while I decided to format data. Now I had a phone with twrp, no data and no access via USB..
I changed the phones usb charging port with no success.
EDL doesnt seem to work either, maybe i am doing it wrong.
I really like this phone, I just repaired the display so I hope it isn't bricked.
Can you help me?
Thanks in advance, if you need further information, just ask!
I'm really appreciate your hardwork ?
Only one solution you have left, open back panel of your phone and find two golden point of EDL mode and then hold two points with joint pin and remember your phone battery should be removed and then connect to pc with hold two golden points now your phone is in EDL MODE then flash with stock rom through mi flash tool and remember inside your pc Modem driver is installed which is required in EDL MODE then that's easier to roll back at initial state of phone ? now your phone work smoothly.
---------- Post added at 01:12 PM ---------- Previous post was at 01:11 PM ----------
I'm really appreciate your hardwork ?
Only one solution you have left, open back panel of your phone and find two golden point of EDL mode and then hold two points with joint pin and remember your phone battery should be removed and then connect to pc with hold two golden points now your phone is in EDL MODE then flash with stock rom through mi flash tool and remember inside your pc Modem driver is installed which is required in EDL MODE then that's easier to roll back at initial state of phone ? now your phone work smoothly.
Check
bCid_diCb said:
Hi, I tried updating to the newest miui.eu release, sadly I couldn't charge my phone after I successfully updated. So I wiped the system to flash the rom I used beforehand. Sadly, now my whole partition couldn't be decrypted and I couldn't access it via USB. So after a while I decided to format data. Now I had a phone with twrp, no data and no access via USB..
I changed the phones usb charging port with no success.
EDL doesnt seem to work either, maybe i am doing it wrong.
I really like this phone, I just repaired the display so I hope it isn't bricked.
Can you help me?
Thanks in advance, if you need further information, just ask!
Click to expand...
Click to collapse
Thus is edl mode test pin points.
bCid_diCb said:
Hi, I tried updating to the newest miui.eu release, sadly I couldn't charge my phone after I successfully updated. So I wiped the system to flash the rom I used beforehand. Sadly, now my whole partition couldn't be decrypted and I couldn't access it via USB. So after a while I decided to format data. Now I had a phone with twrp, no data and no access via USB..
I changed the phones usb charging port with no success.
EDL doesnt seem to work either, maybe i am doing it wrong.
I really like this phone, I just repaired the display so I hope it isn't bricked.
Can you help me?
Thanks in advance, if you need further information, just ask!
Click to expand...
Click to collapse
Edl mode via shorting out the tester point is the only way for you , I beleive your presist or crust partition might have been totally messed up that's why you phone is like this or maybe you didn't enable usb debugging by default luckily your bootloader isn't locked it it was locked then your might have become something like a paperblock of 200grams.
bCid_diCb said:
Hi, I tried updating to the newest miui.eu release, sadly I couldn't charge my phone after I successfully updated. So I wiped the system to flash the rom I used beforehand. Sadly, now my whole partition couldn't be decrypted and I couldn't access it via USB. So after a while I decided to format data. Now I had a phone with twrp, no data and no access via USB..
I changed the phones usb charging port with no success.
EDL doesnt seem to work either, maybe i am doing it wrong.
I really like this phone, I just repaired the display so I hope it isn't bricked.
Can you help me?
Thanks in advance, if you need further information, just ask!
Click to expand...
Click to collapse
Have you tried flashing a rom using miflash https://www.xiaomiflash.com/?
bCid_diCb said:
Hi, I tried updating to the newest miui.eu release, sadly I couldn't charge my phone after I successfully updated. So I wiped the system to flash the rom I used beforehand. Sadly, now my whole partition couldn't be decrypted and I couldn't access it via USB. So after a while I decided to format data. Now I had a phone with twrp, no data and no access via USB..
I changed the phones usb charging port with no success.
EDL doesnt seem to work either, maybe i am doing it wrong.
I really like this phone, I just repaired the display so I hope it isn't bricked.
Can you help me?
Thanks in advance, if you need further information, just ask!
Click to expand...
Click to collapse
i had the same problem years ago with another device ... try to go in twrp press the power botton for 15 sec rebot on twrp format data (not with advanced wipe) and after that a full wipe in advanced wipe.... And look if you solved the encrypt problem.... (Sorry for my bad english)...
---------- Post added at 06:40 PM ---------- Previous post was at 06:17 PM ----------
Yakusha90 said:
i had the same problem years ago with another device ... try to go in twrp press the power botton for 15 sec rebot on twrp format data (not with advanced wipe) and after that a full wipe in advanced wipe.... And look if you solved the encrypt problem.... (Sorry for my bad english)...
Click to expand...
Click to collapse
A lot of time an hard rebot can help... try you can't lose anything ...
I'm curious... let me know if it worked ...
---------- Post added at 08:00 PM ---------- Previous post was at 07:58 PM ----------
Yakusha90 said:
i had the same problem years ago with another device ... try to go in twrp press the power botton for 15 sec rebot on twrp format data (not with advanced wipe) and after that a full wipe in advanced wipe.... And look if you solved the encrypt problem.... (Sorry for my bad english)...
---------- Post added at 06:40 PM ---------- Previous post was at 06:17 PM ----------
A lot of time an hard rebot can help... try you can't lose anything ...
Click to expand...
Click to collapse
I mean with this method...
Yakusha said:
I'm curious... let me know if it worked ...
---------- Post added at 08:00 PM ---------- Previous post was at 07:58 PM ----------
I mean with this method...
Click to expand...
Click to collapse
This method didn't work, I will try the esl option next. I tried it before tho with no success, maybe because I didn't install the qualcomm driver. What could be the problem if my phone still doesn't get recognized?
It's so weird that a software issue causes my phone to not be able to connect to my computer on the recover layer
Try this:. Go in twrp - advanced - terminal - and write reboot edl in the terminal and after that flash the official MIUI rom.... try and let me know...
---------- Post added at 09:00 PM ---------- Previous post was at 08:44 PM ----------
bCid_diCb said:
This method didn't work, I will try the esl option next. I tried it before tho with no success, maybe because I didn't install the qualcomm driver. What could be the problem if my phone still doesn't get recognized?
It's so weird that a software issue causes my phone to not be able to connect to my computer on the recover layer
Click to expand...
Click to collapse
Don't open the phone...
Yakusha said:
Try this:. Go in twrp - advanced - terminal - and write reboot edl in the terminal and after that flash the official MIUI rom.... try and let me know...
---------- Post added at 09:00 PM ---------- Previous post was at 08:44 PM ----------
Don't open the phone...
Click to expand...
Click to collapse
if i type reboot edl in the terminal of twrp, my phone goes into a bootloop, showing the mi.com logo, my computer doesnt recognize anything sadly
Did you try to decrypt in twrp with your account's password?
Yakusha said:
Did you try to decrypt in twrp with your account's password?
Click to expand...
Click to collapse
How to do it?
Yakusha said:
Did you try to decrypt in twrp with your account's password?
Click to expand...
Click to collapse
There is nothing left to decrypt I think. How to do it though(for the next time things go wrong)?
bCid_diCb said:
There is nothing left to decrypt I think. How to do it though(for the next time things go wrong)?
Click to expand...
Click to collapse
With the official rom encrypted when you boot in twrp it ask your password for decrypt... But if you bot in twrp and it don't ask anything then you don't have anything to decrypt...
Try to check the others threads...
I'm pretty sure that you can fix it without open it...
Mouths ago I solved a hard brick on my pixel 2xl that was without fastboot, twrp and pc didn't recognize it... I used a tool for reinstall usb drivers and official rom... I will try to find the guide and send it to you as information...
---------- Post added at 04:24 PM ---------- Previous post was at 03:53 PM ----------
How Windows see you device?... Try to go in device manager and check... if your phone appears in device manager as "QHSUSB_BULK" or unknow device, you have to install the proper driver....
And try this tool https://forum.xda-developers.com/android/software/tool-tool-one-driversunlocktwrpfactory-t3358711
So I tried a lot of things, reboot edl didn't work, Testpoint short-circuit didn't work either.
It's hard to say, but I don't know what happened and I have to say goodbye to my beloved phone. It drives me crazy that I didn't found what happened. I don't even know, if I will flash my next phone.
Thanks for your support, if you want to try your luck, or need a display (2weeks old) or any other part, just pm me.
:crying:
bCid_diCb said:
So I tried a lot of things, reboot edl didn't work, Testpoint short-circuit didn't work either.
It's hard to say, but I don't know what happened and I have to say goodbye to my beloved phone. It drives me crazy that I didn't found what happened. I don't even know, if I will flash my next phone.
Thanks for your support, if you want to try your luck, or need a display (2weeks old) or any other part, just pm me.
:crying:
Click to expand...
Click to collapse
Did you try XiaoMiToolV2 ? When you have all drivers, type in program "my phone is bricked", the program should recognize the phone (turning on in twrp) running in recovery and forcing to fastboot mode.
crt-shadow said:
Did you try XiaoMiToolV2 ? When you have all drivers, type in program "my phone is bricked", the program should recognize the phone (turning on in twrp) running in recovery and forcing to fastboot mode.
Click to expand...
Click to collapse
"No devices found[...]"