Related
To perform a HTC HD2 Leo hard reset
1. With the phone turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then press the END/POWER button shortly and release it. You will then see a message on the screen telling you this will erase xxxxxxxx......
2. Release the VOLUME UP and VOLUME DOWN buttons.
3. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
Soft Reset
If i may add,
A soft reset,
1. Open the back with your thumb or finger
2. The RESET button is located below the bottom left slot for the battery and the SIM card. Use a small object with a blunt point like a toothpick to the RESET button.
3. Your phone will restart and the Home screen appears.
Correct me if im wrong,
Sorry im a newb, but what is the precise difference between hard and soft reset?
Will a soft reset delete stuff such as contacts, pictures and music? And will hard reset do the same?
thanks smaberg...
you should add the two other methods to the first post
there is the soft-reset button (little red button) and a software method (clear storage).
HD2Owner said:
thanks smaberg...
you should add the two other methods to the first post
there is the soft-reset button (little red button) and a software method (clear storage).
Click to expand...
Click to collapse
the "software" method (clear storage) is a hardreset, witch means you will restore it to factory default, deleting all info on phone...
the softreset only restarts the phone.
after flashing a new ROM i always recomend a hardreset afterwards, to be sure to get rid of all leftovers...
(Useful if flashing a rom and battery is less than 50%)
Enter bootloader mode:
Momentary press the red reset button on the back of the device, near the sd card slot, while holding the volume down button. Keep pressing on the Volume down till you see the bootloader screen. If you did not have volume down pressed as you were pressing on the reset button the device is just gonna reset and no change will take place.
Else, you will see "serial" written on the bottom middle of the screen if you're not connected to the PC via USB cable yet. "USB" will replace "Serial" when windows recognizes the device. Once on this state, you can press "next" on the rom installer where you have to acknowledge you connected the device via USB and your battery is grater than 50% and so on and so on.
You can start the installer on the PC prior to connecting the device in Bootloader mode. I don´t know what happens if you enter bootloader while connected to the PC (if you don't either, don't do it!!)
Note: I advise against using this mode with less than 10% or so. I guess you could end up with largest screened brick in the market.
To clarify previous posts:
Hard reset: Resets the device to factory defaults or to the last rom you installed.
How?
-Hardware method: combo of hardware buttons (described above)
-Software method: slide through HTC sence till "Settings" bar and select "Security" (top option). Then select "Factory resets" (last option). To my knowledge it does absolutely the same thing as the hardware method. correct me if I'm wrong.
Soft Reset: changes you made will take effect after the device resets (installed apps or reg edits...) OR you got to a sticky situation and you need to reset to get everything running smooth again (device shows abnormal operation of some kind).
How?
-Software method: Hold the power button till the quick list appears and press "power off" option on the top. You can also be presented with this option after installing some apps or after changing something within an app.
-Hardware method: remove the back cover and press the little red button near the sd card slot. Useful if the device stops responding and you are unable to soft reset by any other way.
Enter Bootloader Mode: allows for flashing devices in any battery state. It doesn't do anything by itself, just allows roms to be flashed. Some people have gotten stuck on this screen http://forum.xda-developers.com/showthread.php?t=599259, so use the search tool and read up before using. After flashing a rom you will loose every setting and file you had on the device itself. SD card will remain untouched (or so it should). I've read people advising to remove the card prior to flashing. Not exactly sure as to why. Files saved to the SD will remain intact. Apps installed on the SD card (aka. "Storage") will remain intact, only not registered or linked with shortcuts anymore. The device basically doesn´t know they exist.
How?
-Harware method: button combo (described above).
-Software method(ish): If you don't have to manually enter bootloader, the rom installer will take your device through this step without you having to do anything besides connecting through USB (activesynk, I guess) and running the RUU_LEO_xxx.exe file. You will see a progress bar on both PC and device as the rom is flashed.
Note: Reseting the device (turned on) while pressing a key (ex.: vol down) does the same thing as pressing the power button (with the device turned off) while pressing that same button (vol down).
Maybe you could transfer this info to the 1st post and clean up the thread a bit... Even, this could be at the Wiki section. Or better, a link on the Wiki to this thread
Hi guys,
I tried with both volume up and down pressed to hard reset, but not really successful. Perhaps I am doing something wrong?
Regards,
Seba
sebacu said:
Hi guys,
I tried with both volume up and down pressed to hard reset, but not really successful. Perhaps I am doing something wrong?
Regards,
Seba
Click to expand...
Click to collapse
did u press power while pressing vol up/down?
Well, for entering bootloader mode, you can do it in "software mode" without having a PC connected to your PPC.
You can just run EnterBootloader.exe from your device.
(see attachment)
wazaaappp said:
did u press power while pressing vol up/down?
Click to expand...
Click to collapse
yes, I did. But when pressing I do not feel that is actually "making contact" I tried several times...
I will try with the bootloader from above...let's see...
Thanks and regards,
Seba
If, for some reason, you cant hard reset using the power button, you can always press the reset button on the back of the device while pressing both vol up and down. After the vibration, it will enter the hard reset menu (remember to keep pressing both vol buttons till this point).
By the way: were you pressing the power button and both vol buttons with the device turned off? Cuz, with it turned on, you are just cycle through the quick list and vol menu like crazy.
Yep...pressing with phone off.
I tried with the reset button from the back of the phone and it worked.
Thanks guys...
Regards,
Seba
I installed this HTC Touch Keyboard + Keypad.cab on my mega and it won't boot anymore. It shows the carrier splash screen, but it won't boot up.
Did you try a hard reset?
i did
Am incercat . At that moment i managed to solve the problem. The device is unable to boot screen popped up in the end. and i just pressed vol -. Now i have the problem again. Worse. It won't get passed the carrier logo. What can I do?
Are you sure you performed a HARD reset? Hold the volume keys down when you turn it on then press volume up to reformat the phone, it should boot.
To do a hard reset follow the steps above:
1. Turn off the phone.
2. Press both the Volume Up and Volume Down
3. While keeping pressed volume Up/Down keys, press power button
4. You should see a RGB screen and then a message asking you to press volume up to do a hard reset. Do it.
5. Wait for the process to complete and you will have a clean phone.
If that won't work, you can try to flash the phone with the rom here:
http://htcpedia.com/ruu_mega_htc_europe/soft/mega-touch2-rom?page=2?page=2
Please do not forget to hard reset after flashing.
If even this will not work, you have a hardware problem and you should have your phone checked by a service.
Hope this helps.
Good luck!
it worked with hard reset
thanks. it worked with a hard reset.
I'm trying to get my hd2 to stay on the tri-colored bootloader screen but it quickly goes to a white screen that says "this operation will delete all your personal data, and reset all settings to manufacturer default. Press VolUp to restore manufacturer default, or press other keys to cancel".
Pressing volup and other keys does nothing. I assume this is because I have CWM installed and im using an android rom.
To clarify: I can boot CWM and my android from nand, but I am trying to run task 29 because my rom is messed up and I can't get the bootloader screen to stay. It thinks I'm trying to reset the data but I'm not.... Any help?
jeffrey92 said:
I'm trying to get my hd2 to stay on the tri-colored bootloader screen but it quickly goes to a white screen that says "this operation will delete all your personal data, and reset all settings to manufacturer default. Press VolUp to restore manufacturer default, or press other keys to cancel".
Pressing volup and other keys does nothing. I assume this is because I have CWM installed and im using an android rom.
To clarify: I can boot CWM and my android from nand, but I am trying to run task 29 because my rom is messed up and I can't get the bootloader screen to stay. It thinks I'm trying to reset the data but I'm not.... Any help?
Click to expand...
Click to collapse
Vol down and power button
Thats what I'm doing and it results in what i described in the first part of my post.
ive tried all sorts of button combinations and none work
Throwin this out there but could ur vol+ button be sticking???when u do vol +/- ull get that screen
i did a button test and all the buttons work like they should, except when i press vol up nothing happens but when i press menu it registers both menu and volup
but yeah volup by itself does nothing...
In order to get to the reset screen you must be pushing the Vol Up + Vol Down + Power on. To get to bootloader it is only Vol Down + Power on. Make sure that you press at the bottom end of the Vol button.
Ok so that means my volup is stuck or malfunctioning. Any ideas on how to remedy this?
Apart from getting a service, No. Sorry.
Sorry if this post is redundant, but the methods I've seen haven't worked, so I can't be alone. Here is how to boot into TWRP if your phone is boot looping/soft bricked. (info pulled from here, of all places.)
1. Make sure phone is completely powered down.
2. Press and hold the Volume down button and the Power button.
3. When the LG logo is displayed release the Power button only then immediately press and hold the Power button again.
4. Release both buttons when the Factory Hard Reset screen displays.
5. Press the power button three times, like it says. Even though it says it will delete everything, it won't (I can confirm that if you are at least on v2.6.3.2).
6. After a "factory reset processing" appears, you should get the TWRP flash screen, and you are good to go.
Hope this helps someone besides currently frustrated me.
I LOVE YOU! I honestly didn't think this would work but it does and i'm so happy.
just about to make a thread asking how to do this. Glad I searched. way to make you jump through hoops tho.
thanks for this. for me the phone didnt even have to be completely powered off.
i wa sin a sleep of death so i held down power and vol down until lg logo appeared let go and then pressed power again. pressed power 3 more times and it booted into recovery
nm
This thread should be stickied in Q&A
jadengore said:
Sorry if this post is redundant, but the methods I've seen haven't worked, so I can't be alone. Here is how to boot into TWRP if your phone is boot looping/soft bricked. (info pulled from here, of all places.)
1. Make sure phone is completely powered down.
2. Press and hold the Volume down button and the Power button.
3. When the LG logo is displayed release the Power button only then immediately press and hold the Power button again.
4. Release both buttons when the Factory Hard Reset screen displays.
5. Press the power button three times, like it says. Even though it says it will delete everything, it won't (I can confirm that if you are at least on v2.6.3.2).
6. After a "factory reset processing" appears, you should get the TWRP flash screen, and you are good to go.
Hope this helps someone besides currently frustrated me.
Click to expand...
Click to collapse
You're a lifesaver.
commissionerg said:
You're a lifesaver.
Click to expand...
Click to collapse
Thank you, doing my best to help out.
Sent from my LG-D800
Awesome. Didn't know this!
Thanks
@jadengore : I was stick in a bootloop, and your thread helps me a lot !
Big thanks !
:good:
Also, if you're too scared to try that, I've had success using rom toolbox to reboot into recovery. Of course this is assuming you have a working system.
Thanks very much, but...
Hello,
I unfortunately dropped my VS980, cracked the screen, and the digitizer only works on the bottom portion of the screen. I have a new screen coming, which should fix this issue, however I would like to get my data off my phone (pics), but I can't as I have a password (draw a line/shape kind) and without being able to enter this in, it will not connect to my PC as mass storage.
I was hoping to be able to boot into recovery with hardware buttons and get my data that way, not sure if that is possible either, but at least try it. This I found to work to get me to the factory hard reset screen, but I am skeptical to push the power button and have it wipe my data!
I am open to other options to get to my data if anyone has any, including android device manager which is something I have thought of, but not sure if I can reset the security to nothing, or maybe as the bottom portion of my digitizer seems to work, I can enter in a space or a period for a password and enter that in.
Looking for any guidance!
Thanks!
Got it!
Redid the password with android device manager, which got me in, but I didn't even need to do that as I had the brainwave to plug a mouse in with a usb adapter. Works flawlessly, got my data, now just waiting for replacement screen!
Strange Problem
I am using F-320K[G2], Cloudy G3 Rom, when I hit boot into recovery it does bring me to TWRP but hardware buttons doesn't work. It just restarts the phone.
Vol down+Power till LG logo up, release and press and hold again and after few secs it restartsand came back to LG screen. If I continue to held it it just repeat restating.
hardware keys to enter recovery. voldown+power then volup+power
RevoDSG said:
I am using F-320K[G2], Cloudy G3 Rom, when I hit boot into recovery it does bring me to TWRP but hardware buttons doesn't work. It just restarts the phone.
Vol down+Power till LG logo up, release and press and hold again and after few secs it restartsand came back to LG screen. If I continue to held it it just repeat restating.
Click to expand...
Click to collapse
steps to enter recovery that worked for my Sprint LG G2 on ZVC firmware.
1) hold power and volume down button till you see LG logo -- quickly release these buttons and
2) immediately hold power and volume up buttons to enter into factory reset menu.
Then 3 presses of power key to confirm wipe and enter TWRP recovery. :good:
I was going mad trying to enter recovery for an hour. It appears like different models/software versions have different key combinations for entering recovery mode.
My phone was stuck at lg logo screen and i didnt have nandroid backup of the phone. so couldn't try the TOT restore method too as i waned my phone data.
Another way to get to Custom Recovery
krezee said:
steps to enter recovery that worked for my Sprint LG G2 on ZVC firmware.
1) hold power and volume down button till you see LG logo -- quickly release these buttons and
2) immediately hold power and volume up buttons to enter into factory reset menu.
Then 3 presses of power key to confirm wipe and enter TWRP recovery. :good:
I was going mad trying to enter recovery for an hour. It appears like different models/software versions have different key combinations for entering recovery mode.
My phone was stuck at lg logo screen and i didnt have nandroid backup of the phone. so couldn't try the TOT restore method too as i waned my phone data.
Click to expand...
Click to collapse
The way that let me get into custom recovery is different.
I hold 'vol up+power+vol down' to start from turned off state and keep holding it[Don't leave just keep holding the 3 buttons]. It doesn't show factory reset screen, it get me into TWRP[Custom Rom] directly. I heard 3 buttons gets u in safe mode IDK but I got into proper working TWRP.
RevoDSG said:
I am using F-320K[G2], Cloudy G3 Rom, when I hit boot into recovery it does bring me to TWRP but hardware buttons doesn't work. It just restarts the phone.
Vol down+Power till LG logo up, release and press and hold again and after few secs it restartsand came back to LG screen. If I continue to held it it just repeat restating.
Click to expand...
Click to collapse
I have a F320S.
Hold Volume up and press the Power Button,when comes Lg Logo release the Power Button and start the TWRP
if anybody's looking for the information in this thread like i was, and the posted method doesn't work (it did not for me):
1. Power off
2. Hold volume down and power
3a. release both at logo AND press BOTH at logo right after releasing
4a. Enter recovery
You should enter recovery, but if not...
3b. Keep the buttons pressed (your phone might continue into the start animation, but if you keep the buttons press it will return)
4b. The first logo will appear. Release both and press BOTH
5. Enter recovery
hope this helps someone
http://forum.xda-developers.com/showpost.php?p=45901939&postcount=3
jadengore said:
Sorry if this post is redundant, but the methods I've seen haven't worked, so I can't be alone. Here is how to boot into TWRP if your phone is boot looping/soft bricked. (info pulled from here, of all places.)
1. Make sure phone is completely powered down.
2. Press and hold the Volume down button and the Power button.
3. When the LG logo is displayed release the Power button only then immediately press and hold the Power button again.
4. Release both buttons when the Factory Hard Reset screen displays.
5. Press the power button three times, like it says. Even though it says it will delete everything, it won't (I can confirm that if you are at least on v2.6.3.2).
6. After a "factory reset processing" appears, you should get the TWRP flash screen, and you are good to go.
Hope this helps someone besides currently frustrated me.
Click to expand...
Click to collapse
this worked omg...thanks a million...
Just wanted to contribute here in case anyone else had tried everything listed in this thread and still was unable to boot into TWRP.
I'm on Sprint, stock, rooted ZVE, and I have TWRP 2.7.
1. Power off phone, wait a few seconds to make sure phone is completely off.
2. Hold power and volume down.
3. As soon as LG logo appears, KEEP holding down power... BUT release volume down and SWITCH to holding volume up.
4. After a few seconds, screen appears saying "Recovery mode" and TWRP opens up after that.
I made a TWRP nandroid backup then restored it after flashing a ROM. This put my phone into a bootloop.
It seems that the only way to access TWRP on the LG G6 is by booting the phone and choosing factory reset from the settings menu. This is the only phone I've owned where I can't simply boot into TWRP through a key combination.
I cannot use ADB because ADB is inaccessible from a bootloop.
Is my phone useless or is there another way to access TWRP?
I was in a similar situation a while back. I think to get into TWRP I held the power button & volume down simultaneously until it asked to factory reset or wipe. I really don't recall. It may have even be the volume up button. Try both and see if it works. If it asks to reset/wipe...whatever it ends up saying, just select YES. It should then boot you to TWRP. It did for me, if I recall correctly.
Goof luck! Hope it helps..
To get in TWRP with button combination:
1 - Hold both Volumes Down key and Power button until the LG Logo is displayed.
2 - Keep holding Volume Down and release the Power button for 1 sec. Then hold it again until the recovery mode is displayed.
3 - Use the Volumes buttons to navigate and select yes for both questions.
You normally should be now in TWRP.