Related
I installed 10k rooted on my P705 and was about to install a custom recovery, when the phone came on it was in emergency mode but the computer could no longer detect it, I have tried all the usb ports on about 4 computers and changed the cable trice, So I'm a little bit sure it's nothing to do with the pc. I have tried putting it on holding volume + and -. Any help will be really appreciated because I am stuck right now.
I have gone through the forum for like 6 hours, I couldn't find anything , I apologize before hand if this was treated elsewhere.
Did you try flashing your stock firmware with Software update [KDZ] 1.0.4.4 (KDZ-Flasher) while in emergency mode?
Remove the Drivers and plug the phone in our PC.. maybe reinstall the Drivers
yes I did try to flash it but the computer doesn't detect it in the first place. So I get a " no phone found"
kevios12 said:
Remove the Drivers and plug the phone in our PC.. maybe reinstall the Drivers
Click to expand...
Click to collapse
thank you but that didn't work either
Just to be clear, you're trying to flash your stock firmware with Software update [KDZ] (KDZ-Flasher), while in emergency mode (your phone in is that yellow emergency mode)?
If so, then maybe try the LG MOBILE SUPPORT TOOL.
I'm not familiar with it, but I read here that it's an alternative to Software update.
need4steer said:
Just to be clear, you're trying to flash your stock firmware with Software update [KDZ] (KDZ-Flasher), while in emergency mode (your phone in is that yellow emergency mode)?
If so, then maybe try the ...
I'm not familiar with it, but I read here that it's an alternative to Software update.
Click to expand...
Click to collapse
Thanks but Thats not exactly the problem, It DOES NOT READ to begin with. If the laptop could detect the phone, then I would be able to flash "anything". My problem is the laptop cannot detect the phone....
I'm confused - what do you mean by "DOES NOT READ"?
Your wrote that you are getting "no phone found" in Software update [KDZ].
So I asked if this is happening when you are in the emergency mode (your phone screen is kind of yellow and there is "emergency mode" in it).
I also wrote that if you were in emergency mode, then try LG MOBILE SUPPORT TOOL.
use another computer, maybe a problem with your OS (windows)
need4steer said:
I'm confused - what do you mean by "DOES NOT READ"?
Your wrote that you are getting "no phone found" in Software update [KDZ].
So I asked if this is happening when you are in the emergency mode (your phone screen is kind of yellow and there is "emergency mode" in it).
I also wrote that if you were in emergency mode, then try LG MOBILE SUPPORT TOOL[/URL].
Click to expand...
Click to collapse
Heres the problem, its not detecting, If you can tell me some way to make the laptop detect the phone in emergency mode, I will be extremely grateful, ps kdz equally says no phone found cuz.... the laptop cannot detect the phone and LG MOBILE SUPPORT TOOL equally cannot find the phone connected to the laptop. So..........................................
d-hammer said:
Heres the problem, its not detecting, If you can tell me some way to make the laptop detect the phone in emergency mode, I will be extremely grateful, ps kdz equally says no phone found cuz.... the laptop cannot detect the phone and LG MOBILE SUPPORT TOOL equally cannot find the phone connected to the laptop. So..........................................
Click to expand...
Click to collapse
Okay, I got it.
Did you install the latest drivers?
If not, you can do so by downloading and installing them from your support site or by downloading and installing LG PC SUITE.
After that please open device manager and see if there's anything there with an exclamation or a question mark. If there is, please don't continue and post back what it is.
Only when you see that everything is okay, disconnect your phone, turn it off, enter into emergency mode (by clicking volume up + volume down + power button), make sure that you're in emergency mode (the yellow screen), connect your phone, run Software update [KDZ] (KDZ-Flasher), make sure to set the right type (CDMA / 3GQCT), make sure to leave the PhoneMode in DIAG, browse your kdz stock firmware file, and then click on "Lunch software update".
I'll be looking forward for your comment.
Please don't give up!
luthfi_11 said:
use another computer, maybe a problem with your OS (windows)
Click to expand...
Click to collapse
thanks but I actually tried it on linux, it didn't detect it either.
d-hammer said:
thanks but I actually tried it on linux, it didn't detect it either.
Click to expand...
Click to collapse
i have no problem with windows 7 & windows 8, just try another computer bro
d-hammer said:
thanks but I actually tried it on linux, it didn't detect it either.
Click to expand...
Click to collapse
Try what I suggested above.
Yesterday i was upgrading my LG P705 to 4.1.2 usind KDZ V20B, but it failed & its now stuck in emergency mode. The main problem is my PC is not recognizing it. I uninstalled LG drivers & installed again, but then also, its not recognised my my PC. Please Help.
---------- Post added at 06:00 PM ---------- Previous post was at 05:54 PM ----------
d-hammer said:
Thanks but Thats not exactly the problem, It DOES NOT READ to begin with. If the laptop could detect the phone, then I would be able to flash "anything". My problem is the laptop cannot detect the phone....
Click to expand...
Click to collapse
u fixed your phone or not. plz help. I'm also stuck in same problem.
diwaker0 said:
Yesterday i was upgrading my LG P705 to 4.1.2 usind KDZ V20B, but it failed & its now stuck in emergency mode. The main problem is my PC is not recognizing it. I uninstalled LG drivers & installed again, but then also, its not recognised my my PC. Please Help.
---------- Post added at 06:00 PM ---------- Previous post was at 05:54 PM ----------
u fixed your phone or not. plz help. I'm also stuck in same problem.
Click to expand...
Click to collapse
Same problem here. I downloaded a program called Optimus Toolkit, as I have an Optimus LGl45c, and the program is for
Linux. Same problem- CAN'T SEE PHONE. Program must use ADB, which CAN'T SEE PHONE while it's in emergency mode, as
apparently the correct partition isn't mounted!! Windows KDZ updater sees phone (try the solution from another blog- run in
different compatibility mode: right click on program>properties>compatibility. this worked for me) but the KDZ Updater can't
find the LGMobileDL.dll... lol! wait til you try it!...) So, for he/she who suggested LG PC Suite, please listen. Suite CAN'T SEE
PHONE either, and refuses to run any further....
Anybody have any tricky ways to flash a boot? It would have to be a Linux hack method.....
I think he did not check usb debugging so cant find phone
Not sure if it will work but no harm trying at this stage:
take out batteries,
wait for 30s,
put it back,
hold power and volume down
when keys light up, touch menu button (not the home button)
feel vibrate?
LOL!
pwhitpod3 said:
Same problem here. I downloaded a program called Optimus Toolkit, as I have an Optimus LGl45c, and the program is for
Linux. Same problem- CAN'T SEE PHONE. Program must use ADB, which CAN'T SEE PHONE while it's in emergency mode, as
apparently the correct partition isn't mounted!! Windows KDZ updater sees phone (try the solution from another blog- run in
different compatibility mode: right click on program>properties>compatibility. this worked for me) but the KDZ Updater can't
find the LGMobileDL.dll... lol! wait til you try it!...) So, for he/she who suggested LG PC Suite, please listen. Suite CAN'T SEE
PHONE either, and refuses to run any further....
Anybody have any tricky ways to flash a boot? It would have to be a Linux hack method.....
Click to expand...
Click to collapse
K. A couple weeks later- for those of you with l45c:
You will get to the point where you find that LGNPST is the only thing that will flash. Having troubles registering the .dll? That cost me
over a week. Move the dll to your system/lg electronics/lgnpst folder and open the cmd window (terminal screen) as administrator.
Edit: Use the command> regsvr32 "name of dll".dll
You should google the regsvr command, as it is different for 64 bit machines, and there is a different system file to put the dll in..
Trouble is, we have no proper dll for the 45c. I tried the ms690 dll with an ms690 bin. Unfortunately, it flashed all the way through- and
now I have a perma-black screen... so don't try that.
I DO have an LGL45C-CT2 binary.... just no dll for the 45c, as usual. Not that it would matter- LGNPST cant see phone any more than
ADB could- there is no more 'emergency download'. I will check the battery, etc...
Morale of story- once again, there is evidence that the l45c is not supported. It is not an MS690, and probably not a P690... Use
LGNPST at your own risk, but quit pounding your head over other methods! Time wasted...
Until next time... keep hacking....
<del>
Hi everyone,
I ****ed up, i know... i had some problems with my G2, the last restauration was with : Europe OPEN D80220H_00.kdz
But i clicked by accident on a buttom from a program saying "fix the partitions problems", after that, the G2 crashed and black screen.
The phone was lighting and i saw everypartitions when it was plugued on my computer, but asking for a format on each partition. so i decided to use this :
http://forum.xda-developers.com/showthread.php?t=2582142
But i ****ed up again and i think it's because i used the wrong files, i used : BIN_LGD802AT-00-V10b-SEA-XX-SEP-04-2013-32G.zip (i don't know if it's because of that ? )
after that, the phone isn't reconized at all from windows and ubuntu... the drivers can't be reconized
I can't see any partition now, so i can't do it again. I don't know what to do now.
I fount another tutorial for extract every img files from my own kdz : "Europe OPEN D80220H_00.kdz" but i can't put them on the phone anymore.
Version : Europe OPEN D80220H_00.kdz
Tel : LG G2 D802 32G Blanc
Thanks in advance !
i'm not able to understand if it is QH USB 9006 or 9008 - you should try contacting member "tungkick" on this forum
sandys1 said:
i'm not able to understand if it is QH USB 9006 or 9008 - you should try contacting member "tungkick" on this forum
Click to expand...
Click to collapse
why ? he will be able to help me ?
Will try, thanks !
Something new :
I have finally set my phone on "download mode" EVEN IF my screen is always black so i dont see ANYTHING on the screen. But i just know that he is really download mode cause i press "top buttom" during puting my usb cable and the connection is faster.
BUT, i tried to use the LGFlashTool (with the tuto) and it says some error "EMEI" and "PID" NULL.
So the program doesn't want to continue :/
Hey guys i've Hard Bricked my Yureka. Phone Doesnt turn on nor goes to fastbooot, instead is only detected in windows as Qusbs-Bulk. Please help ME
Follow the steps shown in link below;
https://cyngn.com/support/
http://forums.yuplaygod.com/threads/factory-images-and-flashing-tools-official.2178/
But my phone does not boot into fastboot
Search at play god forum, there are some procedures given there which may solve your prob. http://forums.yuplaygod.com/threads/help-completely-bricked.4641/#post-45794
HI thanks for help but in all above cases they were soft bricked ..i.e their phones booted in fastboot but mine isnt.
Hmmm ... seriously worried situation haan. {Kiya kya tumne}
If you can tell us what exactly you did, may be then we can help.
I also hardbricked when i tried to port MIUI. But i got replaced by YU without any cost and within 3 days
Exactly me too flashed miui of f2 without boot.img..Was trying to port...
@ Suhas Is the new phone same as old one or a used one??
suhas.holla said:
I also hardbricked when i tried to port MIUI. But i got replaced by YU without any cost and within 3 days
Click to expand...
Click to collapse
I also hardbricked when i tried to port MIUI, Now waiting for the repacement.
Called them and raised the ticket 6 days before, but they are yet to dispatch.. . . . Very frustrating !
Do you have any information on how to unbrick. I searched much but wouldn't find files to unbrick !
1. 8939_msimage.mbn
2. MPRG8939.hex
3. rawprogram0.xml
4. patch0.xml
Hope some one comes to rescue me :crying:
Video Tutorial HOW TO UNBRICK YUREKA
Srry i cant post the youtube link as i am new here
Just go to youtube
Search kanwal deep unbrick yureka
And watch the video
To go in fastbool mode remove battery insert again and press vol up while connecting usb
quakze said:
I also hardbricked when i tried to port MIUI, Now waiting for the repacement.
Called them and raised the ticket 6 days before, but they are yet to dispatch.. . . . Very frustrating !
Do you have any information on how to unbrick. I searched much but wouldn't find files to unbrick !
1. 8939_msimage.mbn
2. MPRG8939.hex
3. rawprogram0.xml
4. patch0.xml
Hope some one comes to rescue me :crying:
Click to expand...
Click to collapse
ahh Same situation I too searched for that files when i had bricked my device
Since the chipset is new. So not able to find
suhas.holla said:
ahh Same situation I too searched for that files when i had bricked my device
Since the chipset is new. So not able to find
Click to expand...
Click to collapse
I have got rom of Huawei C199s (MSM8939), which has many file packed into UPDATE.APP.
I have unpacked it, but the file name and extensions are unknown.
At present I am trying to identify the msimage.mbm and mprg files.
The rom link is http://www.needrom.com/wp-content/uploads/2015/03/C199s-V100R001C92B260-Telecom.zip
Shrihari007 said:
Hey guys i've Hard Bricked my Yureka. Phone Doesnt turn on nor goes to fastbooot, instead is only detected in windows as Qusbs-Bulk. Please help ME
Click to expand...
Click to collapse
ask for replace in customer care. as they told they will replace your mobile even after unlocking boot loader, root.
my device also gone hard bricked not get into the fastboot mode..
and no customer care no. to contact not correct > this one 18602122122
any help
thnks..
You guys can take a look at this thread -
http://forum.xda-developers.com/yureka/help/question-qualcomm-download-mode-k-t3068040
Hit thanks to the creator and me if helped.
suhas.holla said:
I also hardbricked when i tried to port MIUI. But i got replaced by YU without any cost and within 3 days
Click to expand...
Click to collapse
What did you tell the customer support about your phone getting bricked.
I tried calling the support, but they said that they will chargers. 3000 for replacing .
please help
my device got bricked 2 days ago and now there is no fastboot mode and not even the led lights showing up if the device is connected to the pc!! and whats even worse the cc is not picking up the calls
my mobile also hard bricked.
suhas.holla said:
I also hardbricked when i tried to port MIUI. But i got replaced by YU without any cost and within 3 days
Click to expand...
Click to collapse
hi.... my yu yureka also get hard bricked after installing lollipop update from yu.. please tell me the steps you followed to replace your yureka...... please reply fast...
:crying::crying::crying:
issue regarding in functionality in yu yureka after upgrading with lpllipop
dear sir,
my name is anurag. i am using yureka ao 5510 phone after launching official update for phone i upgrade my phone.
i faced sevral problem after updating. the list are provided below.
1) overheating device than normal one while comparing with kitkat.
2) automatically turned off and un- responsive and on screen multicolor circle appeared wih cross over circle, its upto 5-6 hrs after that suddenly screen appeared after turning on mobile and start working.(in this process sevral times i remove battery & reinsert and trying to start it normally).
3) when phone connecting to wi-fi hotspot network (apple tablet over 3g) and i am trying to update apps from playstore its not updated(google play services unfortunately stopped) over wi fi network, but its working good on mobile data.
4) now currently issue in brightnesss control and in setting < storage option < USB computer connection the checkbox option are not apperared & phone not connected to computer(using windows 8.1 ),
please kindly fix this buges...
and provide some patch or system updates as earliar as possible to overcomethis issue.
So I intstalled the WP10 preview which includes support for the 520, but the settings app didn't work and I couldn't reset the device so I used the Windows Phone Recovery Tool to revert to 8.1. However, as the firmware was about to install, the device went into flash mode (as it does while installing a firmware) and an error dialgue opened on my laptop saying that there was an error. After that my phone's screen went black and its not vibrating or powering on even when connected to a power source. I doubt that it is restorable, but any help would be much appreciated
Thank you guys for letting me know about the link I'm posting it in the OP so that everyone having this issue can upvote on that thread.
Link: https://social.technet.microsoft.co...e-recovery-possible?forum=WinPreview2015Phone
theevilpotato said:
So I intstalled the WP10 preview which includes support for the 520, but the settings app didn't work and I couldn't reset the device so I used the Windows Phone Recovery Tool to revert to 8.1. However, as the firmware was about to install, the device went into flash mode (as it does while installing a firmware) and an error dialgue opened on my laptop saying that there was an error. After that my phone's screen went black and its not vibrating or powering on even when connected to a power source. I doubt that it is restorable, but any help would be much appreciated.
Click to expand...
Click to collapse
I've just got the exact same error and I've spent the last hours trying everything possible and every tutorial to make it work. I'm afraid it's completely bricked. It's not responding to anything, when plugged into the pc it shows up as "QHSUSB_DLOAD" which is usually a very bad sign, and every software recovery or phone recovery tool I've tried from MS and Nokia either don't detect it or say it's not supported.
It's dead.
520? :/ Same here. Time to get a new phone for school, I guess.
Yes, a 520 as well.
Just a heads up, if you give the windows phone subreddit a quick read you'll notice we are not the only people to have this issue. Apparently several other people trying to roll back their phone have it completely bricked and in the QHSUSB_DLOAD situation.
I don't think MS can do anything about it, since the boot crapped out you either need to buy the tools or get it repaired by someone having them, but at least it proves there is some kind of problem with rolling back from the preview.
angstdasein said:
I've just got the exact same error and I've spent the last hours trying everything possible and every tutorial to make it work. I'm afraid it's completely bricked. It's not responding to anything, when plugged into the pc it shows up as "QHSUSB_DLOAD" which is usually a very bad sign, and every software recovery or phone recovery tool I've tried from MS and Nokia either don't detect it or say it's not supported.
It's dead.
Click to expand...
Click to collapse
same here
After a bit of reading more and more people are reporting this, so please put your own experience on this technet thread, it's a good idea to centralize reports where Microsoft can see it.
I can't link it here (don't have the permission to post links yet) but it's the first result by typing "Lumia 620 bricked during rollback procedure: recovery possible?" in google.
NL525 w/ red screen here.
feherneoh, pls make tutor!
feherneoh said:
Here it is:
...
Click to expand...
Click to collapse
Praise the Lord feherneoh!
Greatest thanx to ya!
Same error here, black screen and phone do nothing.
Tried with Thor2 but didn't work.
azogh said:
Same error here, black screen and phone do nothing.
Tried with Thor2 but didn't work.
Click to expand...
Click to collapse
Be sure using good cable. Try few times (i did 3)
[QRCODE][/QRCODE]The same problem with L520. There is already post on Technet regarding this problem
You can search Google by typing in: QHSUSB_DLOAD technet
Please upvote, then we would have some respond from Microsoft, maybe alternative driver, tool or something...
My Nokia does not turn on
The same problem! My Nokia does not turn on. I've tried everything! Any solution?
rickmaran said:
The same problem! My Nokia does not turn on. I've tried everything! Any solution?
Click to expand...
Click to collapse
I don't think there is a solution yet. Just keep and eye on this and hope for the best: https://social.technet.microsoft.co...e-recovery-possible?forum=WinPreview2015Phone
Have you anyone has try using Lumia Recovery Tool ?
1. Download ffu saperatly. (8.1 GDR1)
2. Install Lumia Software Recovery Tool.
3. Launch recovery tool.
4. Remove battery, usb, device.
5. Select my phone doesn't respond in recovery tool.
6. Insert battery, usb, plug it to pc.
7. A- Press and hold volume down.
B- Press and hold Power + volume down
8. Flash it.
Hope this will work.
feherneoh said:
Here it is:
1: Find your Recovery Tool folder on your harddisk. Mine is "C:\Program Files (x86)\Microsoft Care Suite\Windows Phone Recovery Tool"
There should be a file called thor2.exe there.
2: Open an administrator command prompt here
3: Find the ROM Recovery Tool downloaded. Should be in "C:\ProgramData\Microsoft\Packages\Products"
You will need the FFU file for your device.
Mine is "C:\ProgramData\Microsoft\Packages\Products\rm-914\RM914_3058.50000.1425.0005_RETAIL_eu_hungary_429_05_443088_prd_signed.ffu"
4: To flash your device with THOR2, enter this to commandline:
Code:
thor2 -mode uefiflash -ffufile "C:\ProgramData\Microsoft\Packages\Products\rm-914\RM914_3058.50000.1425.0005_RETAIL_eu_hungary_429_05_443088_prd_signed.ffu"
Replace filename with your own
5: After flashing completes, reboot your phone by entering this:
Code:
thor2 -mode rnd -bootnormalmode
Click to expand...
Click to collapse
It says this error:
THOR2 1.8.2.14 exited with error code 393220 <0x60004>
Click to expand...
Click to collapse
zuchit said:
It says this error:
Click to expand...
Click to collapse
Same case
Same problem with DLOAD
The solution seems to do a JTAG... Bad news for normal people ::crying:
Bricked Nokia Lumia
Actually, the red screen means that the phone went into its UEFI MODE.
In UEFI MODE your phone could be restored as normal by a HARD RESET (see key combo).
If you have a hard luck, your phone will automatically start in Flashing Mode (IMO(0x0000001)) which only works on the downloading procedure when on Rolling back.
The RollBack program has to put your phone in Flashing Mode in order to gain access to it's microchip.
Well the app itself knows what to do, but something failed.
In this point, you disconnected the phone and tried all you've known to power it on. Meanwhile the app deleted it's cache file, it no longer knows why your phone is in that state and your PC will get it as QHSUSB_DLOAD which is a Side_Load driver for Qualcomm Enabled Phones.
At this point, RIFF JTAG is the only solution as your BOOTLOADER is dead.
Good thing? It could be fixed by any GSM Service and the price could be small.
DO NOT try any Nokia Care / Refurbish / Restore app. All of them are created to work with a phone that has it's bootloader working.
None of them will cooperate to reflash it.
Even if you manage to reflash the OS, you don't have a BIOS / BootLoader....
Hopefully, Microsoft will create a tool to fix this as it only occurs when Rolling Back from Windows 10 Tech. Prev. and 8.1 to 8.
But until that, your phone is dead.
Source of info: I'm working as an G.S.M. RepairMan.
feherneoh said:
Maybe some error message before this?
Click to expand...
Click to collapse
at the moment, i get this error when i cmd thor right after connecting phone to usb. (screenshot 1)
i58.tinypic. com/2qnz51d.jpg
Click to expand...
Click to collapse
these is what it says when i try cmd thor after red screen with Nokia logo appers.. (screenhot 2)
i61.tinypic. com/jkftq8.jpg
Click to expand...
Click to collapse
Can i do anything if my lg g6:
can't access fastboot and download mode
won't load into rom (they may not be one afterall xD)
is only stuck on lg g6 thinq logo
pc doesnt see the device when plugging in
only thing i can do is hold power and volume- buttom to do a factory reset which is the way to access twrp (which is not loading in)
bootloader is unlocked
and ideas or throw this trash?
I have the same situation like this Would love someone to express their opinions on the situation.
Kerres said:
Can i do anything if my lg g6:
can't access fastboot and download mode
won't load into rom (they may not be one afterall xD)
is only stuck on lg g6 thinq logo
pc doesnt see the device when plugging in
only thing i can do is hold power and volume- buttom to do a factory reset which is the way to access twrp (which is not loading in)
bootloader is unlocked
and ideas or throw this trash?
Click to expand...
Click to collapse
BubisUK said:
I have the same situation like this Would love someone to express their opinions on the situation.
Click to expand...
Click to collapse
You guys can still unbrick by putting the phone in 9008 mode and using the QFil method mentioned here:
https://forum.xda-developers.com/lg-g6/how-to/lg-g6-unbrick-method-t3935924
(Thank the OP in the thread.)
OP above does warn that the method will not work for T-Mobile version of g6, H872.
Do make sure that phone is detected in 9008 mode when you connect to Windows PC. If it is not detected, you might have to put phone in 9008 mode by grounding the connection point on motherboard. You will need to remove the back glass, some screws and and connect the connection point located below flash for camera to the ground plate in phone as shown here:
https://forum.xda-developers.com/lg-g6/how-to/lg-g6-testpoints-edl-mode-9008-t3916962
(Thank the OP in the thread.)
Let's hope your phones are already detected in 9008 mode on PC so you don't have to open the back of phone. This is a bit complicated process and not many will be able to help you if you get stuck with anything, so best would be to read through the posts and making sure you understand all the steps before proceeding and asking OP in those threads if you get stuck. I have only used this method once and it worked for me. There is no visible indication when phone enters EDL mode by short circuiting the board. Have a device manager window open and phone connected to the PC via USB when you attempt short circuit so you know once it enters 9008 mode. Good Luck.
Android# said:
You guys can still unbrick by putting the phone in 9008 mode and using the QFil method mentioned here:
https://forum.xda-developers.com/lg-g6/how-to/lg-g6-unbrick-method-t3935924
(Thank the OP in the thread.)
OP above does warn that the method will not work for T-Mobile version of g6, H872.
Do make sure that phone is detected in 9008 mode when you connect to Windows PC. If it is not detected, you might have to put phone in 9008 mode by grounding the connection point on motherboard. You will need to remove the back glass, some screws and and connect the connection point located below flash for camera to the ground plate in phone as shown here:
https://forum.xda-developers.com/lg-g6/how-to/lg-g6-testpoints-edl-mode-9008-t3916962
(Thank the OP in the thread.)
Let's hope your phones are already detected in 9008 mode on PC so you don't have to open the back of phone. This is a bit complicated process and not many will be able to help you if you get stuck with anything, so best would be to read through the posts and making sure you understand all the steps before proceeding and asking OP in those threads if you get stuck. I have only used this method once and it worked for me. There is no visible indication when phone enters EDL mode by short circuiting the board. Have a device manager window open and phone connected to the PC via USB when you attempt short circuit so you know once it enters 9008 mode. Good Luck.
Click to expand...
Click to collapse
You ar a star I will try using the method you linked here, thank you and have a nice day