Related
So I'm rooted with TWRP loki and had CM 11 on and running for a while. I just downloaded the latest nightly through CM OS and it asked to be rebooted.
Upon rebooting to TWRP and installing the update it then just kept on trying to reboot with the CM logo. I cannot get the power and volume keys to boot it to recovery and my computer won't recognize it in this state to boot into recovery.
Any ideas??!! Please! I don't know of any way to restore it.
wave28 said:
So I'm rooted with TWRP loki and had CM 11 on and running for a while. I just downloaded the latest nightly through CM OS and it asked to be rebooted.
Upon rebooting to TWRP and installing the update it then just kept on trying to reboot with the CM logo. I cannot get the power and volume keys to boot it to recovery and my computer won't recognize it in this state to boot into recovery.
Any ideas??!! Please! I don't know of any way to restore it.
Click to expand...
Click to collapse
have you tried turning it off entirely then booting into recovery and flashing a)an older cm11 or b)nandroid backup
XxZombiePikachu said:
have you tried turning it off entirely then booting into recovery and flashing a)an older cm11 or b)nandroid backup
Click to expand...
Click to collapse
I had to take the back off and manually unplug the battery to turn it off. Then I tried the button combinations posted *power and V down* when LG logo comes on repeat to get to wipe screen. However, the phone did not go to the wipe screen, it just rebooted again.
If I could get it to boot to recovery I'd be golden.
wave28 said:
I had to take the back off and manually unplug the battery to turn it off. Then I tried the button combinations posted *power and V down* when LG logo comes on repeat to get to wipe screen. However, the phone did not go to the wipe screen, it just rebooted again.
If I could get it to boot to recovery I'd be golden.
Click to expand...
Click to collapse
have you tried getting into download mode while powered off volume up and plug into pc
XxZombiePikachu said:
have you tried getting into download mode while powered off volume up and plug into pc
Click to expand...
Click to collapse
Success!! I'm in Download Mode... What next? ADB still doesn't look to be recognizing the phone.
wave28 said:
Success!! I'm in Download Mode... What next? ADB still doesn't look to be recognizing the phone.
Click to expand...
Click to collapse
well you should be able to use this guide http://forum.xda-developers.com/showthread.php?t=2432476 to get back to stock make sure you download correct files for your device
XxZombiePikachu said:
well you should be able to use this guide http://forum.xda-developers.com/showthread.php?t=2432476 to get back to stock make sure you download correct files for your device
Click to expand...
Click to collapse
Fingers crossed. Appreciate the help. I don't think I can go back to my Nexus!
XxZombiePikachu said:
well you should be able to use this guide http://forum.xda-developers.com/showthread.php?t=2432476 to get back to stock make sure you download correct files for your device
Click to expand...
Click to collapse
Error due to low batter. I'll have to see if I can charge it without it wanting to turn on. However, it looks promising -- after three times trying I got the utility to recognize the device at least!
Either way, I appreciate the assistance.
wave28 said:
Error due to low batter. I'll have to see if I can charge it without it wanting to turn on. However, it looks promising -- after three times trying I got the utility to recognize the device at least!
Either way, I appreciate the assistance.
Click to expand...
Click to collapse
SWEET!! Took a LOT of doing but it finally got restored to stock! Let's pray that never happens ever again!!!
wave28 said:
SWEET!! Took a LOT of doing but it finally got restored to stock! Let's pray that never happens ever again!!!
Click to expand...
Click to collapse
great to see everythings up and running
wanted to root the device so i kept my phone on fast boot and unlocked bootloader then i tried to flash TWRP recovery, everything seem to be okay till now, bt when i unplugged my phone and tried to go into recovery by pressing unlock+volumeup+volume down, it shows the YU logo then the screen blinks and again it shows YU logo, and nothing happens, bt when i try to rebot the phone, it works normally. I dont know what kind of problem i am facing please help me, unable to go to recovery mode :crying:
I am having the same issue
Hatzzz said:
wanted to root the device so i kept my phone on fast boot and unlocked bootloader then i tried to flash TWRP recovery, everything seem to be okay till now, bt when i unplugged my phone and tried to go into recovery by pressing unlock+volumeup+volume down, it shows the YU logo then the screen blinks and again it shows YU logo, and nothing happens, bt when i try to rebot the phone, it works normally. I dont know what kind of problem i am facing please help me, unable to go to recovery mode :crying:
Click to expand...
Click to collapse
Dude I did the same things as you and even my recovery is not working i tried searching everywhere but i didnt find any fix, Can anyone plz help us :crying:
double0seven37 said:
Dude I did the same things as you and even my recovery is not working i tried searching everywhere but i didnt find any fix, Can anyone plz help us :crying:
Click to expand...
Click to collapse
Sorry for the late reply, I am new to xda forum. I faced the same issue when I switched from cwm to twrp. You can try flashing cwm recovery with the help of rashr or flashify app. Both are free apps and are available on play store. You can google how to use these apps. There are many sites and blogs explaining the steps. You can also use all-in-one tool for yureka to flash cwm/twrp. You can find this tool on xda forum with detailed help.
Good luck.
Yes use flashify app to flash twrp recovery if you have root access. I used this method and I am able to boot into recovery.
See guyzzzz..if u can reboot ur phone ....u first go to settings>developer options>advanced reboot...make it on ..then just click the powe button (as for restart or shut down) u just click on reboot....as u reboot u get 4 options .....in that u get recovery....just click that u will be in recovery....if u can't msg agaim...
Hi guys, I have a problem with my LG G2 16gb. Today I have upgraded CM 13 with the last nightly. After having flashed Rom and Gapps I rebooted the system. The system runs but with some bugs (dialer crashes, screen doesn't wake up anymore when it goes in standby mode). So I decided to come back to the previous nightly, but I suddenly appreciated that I can't go in recovery mode.
I can go in download mode but both Flashtool and SRKtool don't work. I really don't know how to do.
I admit that I'm not able to resolve 2% problem with the fix.
I read that if I try to flash a firmware 10A then Flashtool should work, but I didn't manage to find a mirror of it.
Someone could help me? I Would be grateful
Same problem here. Flashed from cm-13.0-20160427 to cm-13.0-20160430 and now have the same problems. Using d802 with twrp-3.0.2-0
CM is booting, but has the same bugs as written above - no dialer, once in standby screen doesnt wake up any more.
I tried to reboot in Recovery from booted CM, the Phone is hanging with the "Reboot" on Screen. Same with normal reboot or shutdown. It just hangs. The Combination with the Volume Key Down & Power wont let me in Recovery as usual.
CM13 ist really awesome and nightly to nightly it was getting better, but the nightly today just went that wrong.
Would be nice if there is some solution to get the phone back working.
Thanks a lot for any advice or help!!!
Greetings,
Feldinos
fedu89 said:
Hi guys, I have a problem with my LG G2 16gb. Today I have upgraded CM 13 with the last nightly. After having flashed Rom and Gapps I rebooted the system. The system runs but with some bugs (dialer crashes, screen doesn't wake up anymore when it goes in standby mode). So I decided to come back to the previous nightly, but I suddenly appreciated that I can't go in recovery mode.
I can go in download mode but both Flashtool and SRKtool don't work. I really don't know how to do.
I admit that I'm not able to resolve 2% problem with the fix.
I read that if I try to flash a firmware 10A then Flashtool should work, but I didn't manage to find a mirror of it.
Someone could help me? I Would be grateful
Click to expand...
Click to collapse
if the phone boots into system use flashify to install twrp..
if not maybe using srk tools. will help..
why it doesnt work flashtools?
raptorddd said:
if the phone boots into system use flashify to install twrp..
if not maybe using srk tools. will help..
why it doesnt work flashtools?
Click to expand...
Click to collapse
flashtool stops at 2%, I don't know why.
srktool doesnt know my lg g2..
fedu89 said:
Hi guys, I have a problem with my LG G2 16gb. Today I have upgraded CM 13 with the last nightly. After having flashed Rom and Gapps I rebooted the system. The system runs but with some bugs (dialer crashes, screen doesn't wake up anymore when it goes in standby mode). So I decided to come back to the previous nightly, but I suddenly appreciated that I can't go in recovery mode.
I can go in download mode but both Flashtool and SRKtool don't work. I really don't know how to do.
I admit that I'm not able to resolve 2% problem with the fix.
I read that if I try to flash a firmware 10A then Flashtool should work, but I didn't manage to find a mirror of it.
Someone could help me? I Would be grateful
Click to expand...
Click to collapse
I had some problems with booting into recovery as wel. CM13's latest nightly kept freezing my phone and I wanted to go back to my previous backup, but I couldn't boot into recovery from anywhere. Luckily I remembered that the button combination has changed with the latest bootstack I installed. It'sn now like this:
Force a shutdown by holding the power button. As soon as it goes black, press power + vol down, release as soon as the logo appears and then hold vol down + vol up. Then you should be able to get into recovery.
Thoms92 said:
Force a shutdown by holding the power button. As soon as it goes black, press power + vol down, release as soon as the logo appears and then hold vol down + vol up. Then you should be able to get into recovery.
Click to expand...
Click to collapse
Thanks a lot for that information! Almost forgotten that i had installed an new boostack as i flashed the first CM13 nightly that was released.
I was now able to get in recovery and flash 04-27 nightly. Now my phone works normal like it does before i flashed 04-30.
Greetings,
Feldinos
fedu89 said:
flashtool stops at 2%, I don't know why.
srktool doesnt know my lg g2..
Click to expand...
Click to collapse
i think that d802 stuck at 2% but wait and itll be flashed.. i think ive read that somewhere...
are you using windows 7/ usb por 2.0/
here take a look here
http://forum.xda-developers.com/lg-g2/development-d802/fix-lg-flash-tool-stuck-2-t3031112
Thoms92 said:
I had some problems with booting into recovery as wel. CM13's latest nightly kept freezing my phone and I wanted to go back to my previous backup, but I couldn't boot into recovery from anywhere. Luckily I remembered that the button combination has changed with the latest bootstack I installed. It'sn now like this:
Force a shutdown by holding the power button. As soon as it goes black, press power + vol down, release as soon as the logo appears and then hold vol down + vol up. Then you should be able to get into recovery.
Click to expand...
Click to collapse
Thank you so much for the advice! it had been so useful that I managed to get into recovery!
You saved my money, because I was starting thinking about a phone's forced change
I came back to cloudy because I wouldn't find myself in this situation once another!
raptorddd said:
i think that d802 stuck at 2% but wait and itll be flashed.. i think ive read that somewhere...
are you using windows 7/ usb por 2.0/
here take a look here
http://forum.xda-developers.com/lg-g2/development-d802/fix-lg-flash-tool-stuck-2-t3031112
Click to expand...
Click to collapse
When it reaches 2%, it suddenly appears a message telling me that my g2 is disconnected.
Unfortunately for modding, I installed w10. My pc has gotten better, but almost all the programs for modding don't work anymore. In addition to this, I didn't found drivers working well.
I'm thinking about restore w8.1.
There's a way to fix the problem of 2%, but I am not so prepared to use adb.. I'm aware about my limits
fedu89 said:
Thank you so much for the advice! it had been so useful that I managed to get into recovery!
You saved my money, because I was starting thinking about a phone's forced change
I came back to cloudy because I wouldn't find myself in this situation once another!
Click to expand...
Click to collapse
You're welcome As long as you can remember the different button combinations to get into recovery, you shouldn't be afraid to flash roms. Just never forget to make a nandroid backup before upgrading any rom!
If you start to flash roms, you WILL mess up at least once And this time, it wasn't actually your fault, CM13 messed up.
fedu89 said:
When it reaches 2%, it suddenly appears a message telling me that my g2 is disconnected.
Unfortunately for modding, I installed w10. My pc has gotten better, but almost all the programs for modding don't work anymore. In addition to this, I didn't found drivers working well.
I'm thinking about restore w8.1.
There's a way to fix the problem of 2%, but I am not so prepared to use adb.. I'm aware about my limits
Click to expand...
Click to collapse
if there is read the go back to stock in the general section.. read and if cant find answer then ,ask in the thread..
and be especific everything pc and phone..
Hello everyone,
here what's happenend:
I have downloaded the ota normally
charge enough
click on install
the installation looked normal
after the installation was finished it boots normally until the "Android was updating, optimize apps.." come that runs from 0 to 89 apps and then it reboots
and at this point something went wrong.
the oneplus bootlogo appeard and the boot animation plays. but when it finished the screen is black and after a few seconds the "android was updating" banner appeard again.
then it goes again in the bootanimation and so on..
i've restarted my phone by pushing the powerbutton once. still not working.
My phone is stock!
no root
no costum recovery
I hope you can help me.
Cheers, Confused.
additional Information
i'm able to open the recovery mode
confusedx3 said:
i'm able to open the recovery mode
Click to expand...
Click to collapse
If you are able to boot into twrp then follow the guide mentioned below (Twrp has MTP enabled just in case u didn't know) :
http://forum.xda-developers.com/oneplus-2/general/zip-oxygenos-3-x-t3392826
thank you for the answer.
i dont have twrp installed i've only the stock recovery
what if i do a factory reset ?
i read this as a solution here:
https://www.reddit.com/r/oneplus/comments/3mtavv/opt_stuck_in_boot_loop_after_ota_update/
do you think that work in my case ?
confusedx3 said:
thank you for the answer.
i dont have twrp installed i've only the stock recovery
what if i do a factory reset ?
i read this as a solution here:
https://www.reddit.com/r/oneplus/comments/3mtavv/opt_stuck_in_boot_loop_after_ota_update/
do you think that work in my case ?
Click to expand...
Click to collapse
Yes
i am also stuck at same situation but the prob is i hav no recovery installed and i dont want to loose my internal data...is there a way to roll back ????
same here
I also installed through the software update button.
Everything seemed to work fine till optimizing apps.
Then my phone was showing starting apps...
it did it for an indefinite time and then i pressed the power button to reboot the phone.
however now it is not moving beyond the android logo and i dont want to lose my data so i am not clearing data.
i tried clearing my cache.
Any help please?
I am using stock recovery,unrooted phone,OOS 3.0.2
Hi, Iam just a member who wishes to share the solutions to problems related to Softbricks, Hardbricks, Bootloops & IMEI which I personally experienced and got the solutions here on XDA Forums. I will try to elaborate everything in detail as possible and will mention only the steps I took to recovering My Yu Yureka. Please read and follow word to word exactly & you should have your Yureka running in less than an hour.
For Softbricks & Hardbricks please refer to this thread : http://forum.xda-developers.com/yureka/orig-development/tool-brick-yureka-device-using-t3442862
To recover IMEI, please refer to this thread : http://forum.xda-developers.com/yureka/help/recovering-lost-imei-yu-yureka-yunique-t3331485
Please understand the procedures. Main thing, remain calm, everything is going to be all right with the right commands.
Things you need before following all procedures can be downloaded on the threads mentioned above.
I hope & believe all of you can revive your Yu Yureka back to life with this. I did. So can you.
Please don't forget to hit Thanks to me and the people from the above threads if this helps you. And also try to spread the good word to fellow members suffering from similar problems.
Thanks & Good Luck.
Can you help me?!!
Hey bro, it's Nikhil from punjab. I'm facing a new problem. My yureka stucked in bootloop and continuously restarting but not starting. I'm very much concerned about my data, as i don't have any backup! Can you help me in this problem? If you know any helpful solution then please guide me! Your help will be appreciated. (My phone is not rooted)
Nik8910 said:
Hey bro, it's Nikhil from punjab. I'm facing a new problem. My yureka stucked in bootloop and continuously restarting but not starting. I'm very much concerned about my data, as i don't have any backup! Can you help me in this problem? If you know any helpful solution then please guide me! Your help will be appreciated. (My phone is not rooted)
Click to expand...
Click to collapse
Hi Nikhil,
Can you try to get into recovery mode? You need to understand a few commands of ADB also. Don't worry. Your phone will be working again. Remove the battery for a few seconds and put it back. Don't start the phone. First hold the volume up button and then at the same time hold the volume down button. Keep pressed both the buttons and then press the ON button ( All three buttons at the same time ). After your device vibrates a little and sows the YU Logo, let go of all the buttons......you should get into the bootloader menu. Tell me if you can do that. Will explain the steps further after you reply.
Yes I can enter into the recovery mode, but when I try to enter into the bootloader it shows fastboot mode for a sec and then all black screen. I want to tell you that my phone is not rooted and neither i unlocked the bootloader nor installed twrp or cmw!! But still it is bricked without any reason. Is there any solution to recover my data??
Nik8910 said:
Yes I can enter into the recovery mode, but when I try to enter into the bootloader it shows fastboot mode for a sec and then all black screen. I want to tell you that my phone is not rooted and neither i unlocked the bootloader nor installed twrp or cmw!! But still it is bricked without any reason. Is there any solution to recover my data??
Click to expand...
Click to collapse
Hi,
Are you able to get your data back from the bricked Yureka phone.???
My yureka also suddenly not booting, stuck at logo. need to get my contacts from phone memory.
Is there any way to get back??
glaber said:
Hi,
Are you able to get your data back from the bricked Yureka phone.???
My yureka also suddenly not booting, stuck at logo. need to get my contacts from phone memory.
Is there any way to get back??
Click to expand...
Click to collapse
Hey there, not yet buddy im still on the track. I'm searching and waiting for a suitable solution by which I can get my whole backup, but didn't get any yet. :/ Still hoping for the best! It's a horrible situation for me from the last 3 days. Don't know what to do! Someone please help!
Problem solveed
Nik8910 said:
Hey there, not yet buddy im still on the track. I'm searching and waiting for a suitable solution by which I can get my whole backup, but didn't get any yet. :/ Still hoping for the best! It's a horrible situation for me from the last 3 days. Don't know what to do! Someone please help!
Click to expand...
Click to collapse
Hi,
I am able to get my phone back.
I just downloaded the file from http://builds.cyngn.com/factory/tomato/cm-12.1-YOG4PAS3JM-tomato-signed.zip and copied to memory card.
Insert the memory card my phone and then booted into recovery mode.
From recovery mode, select Install/Update zip from sdcard. Andriod got updated.
after update, reboot the phone. It took almost 10mins to boot.
After reboot, I had all my data.
Hope you ll get ur data back.
Thanks
Yureka
my yureka when power on reboots means the YU logo pos and closes then again pops and closes...and when I power on my phone when charger is connected the phone starts perfectly everything works and when I unplug the charger it again powers offs..need a solution please help
Same problem after flashing stock ROM also not able to fix boot loop what to do now
---------- Post added at 06:53 PM ---------- Previous post was at 06:49 PM ----------
Same problem after flashing stock ROM also not able to fix boot loop what to do now if I connect my mobile to charger then it boots and open the home after some time again it boot loops plz help
Chandu710 said:
my yureka when power on reboots means the YU logo pos and closes then again pops and closes...and when I power on my phone when charger is connected the phone starts perfectly everything works and when I unplug the charger it again powers offs..need a solution please help
Click to expand...
Click to collapse
i am also facing same problem please help me guys
is the problem solved , am facing the similar problem. i have flashed CRdroid rom and it worked fine for two days, my phone switched off suddenly when i was using it and from then it restarts at yu logo when charger is unplugged, when the charger in plugged in it runs for a minute and restarts.. any suggestion is appreciated..!!
i am facing issue with my yureka plus,
not going in fastboot mode. only blank screen is comming with download faild images.
plz give solution
how to go in fastboot????:crying:
Sir,
After going on the link,
I followed every instructions perfectly,
My device was soft bricked,
I ran the Complete unbrick tomoto bat file,
also i connected my phone in fastboot mode,
then suddenly,
the process stopped and as far as I think my device got Hard bricked,
the device can't even get into fastboot mode,
just red light LED on connecting the usb
please help sir..
I BEG OF YOU SIR,
PLEASE.
venkateshchandra said:
is the problem solved , am facing the similar problem. i have flashed CRdroid rom and it worked fine for two days, my phone switched off suddenly when i was using it and from then it restarts at yu logo when charger is unplugged, when the charger in plugged in it runs for a minute and restarts.. any suggestion is appreciated..!!
Click to expand...
Click to collapse
Hello..watching my switched off yureka for over 3 days now. Tried flashing cwm recovery finding nothing else to do. Till that time I hadn't tried switching the phone on while plugged in. Don't know if the cwm recovery thing worked or not, but from then on I am unable to reach the recovery (vol up+vol down+power).
But then suddenly in the plugged in state my phone comes alive and boots completely!!!:cyclops::victory:. And then I get to know that while charging, the gandu phone is completing its boot process. But after a few minutes its blacking out and starting its on and off routine again. (minutes varying from 1 to 45 , not sure depending on what, because now I am running hotspot and LTE on the phone to write this on the laptop..and yet it is awake for more than 45 minutes now got a vibe that if the screen is turned off the phone will not shut down. ) ... guys please help. how to make it work without the usb pushed at its back...?
Edited a day later: went to the service centre.. They simply said the battery needs to be replaced. Yes it is all good now. Relieved.
Cant go out of the Bootloop
I don't know what happened,my phone was working really fine.I was using CM 13.0 Snapshot Rom. But then when I reset my phone by going into Setting>Backup & Reset my phone got switched off for rebooting but then it didn't start...its continuously rebooting after the YU logo..I cant even go to the recovery..I had twrp....I tried to install the recovery again using fastboot but it didnt work...even flashed the Stock CM 12.0 firware via fastboot but nothing happened...please help...
Back from Ashes !!!
antim098 said:
I don't know what happened,my phone was working really fine.I was using CM 13.0 Snapshot Rom. But then when I reset my phone by going into Setting>Backup & Reset my phone got switched off for rebooting but then it didn't start...its continuously rebooting after the YU logo..I cant even go to the recovery..I had twrp....I tried to install the recovery again using fastboot but it didnt work...even flashed the Stock CM 12.0 firware via fastboot but nothing happened...please help...
Click to expand...
Click to collapse
Hey Buddy , Same here I am also using RR N, and suddenly one fine morning it went into bootloop. I am stuck at YU logo. Can you confirm that it stucks at userdata erasing and formating data/factory as well ?
I did a lot of research and I think i found out solution. Now my phone is reseting once it starts I will confirm.:fingers-crossed::fingers-crossed::fingers-crossed::fingers-crossed:
kalagikr said:
Hey Buddy , Same here I am also using RR N, and suddenly one fine morning it went into bootloop. I am stuck at YU logo. Can you confirm that it stucks at userdata erasing and formating data/factory as well ?
I did a lot of research and I think i found out solution. Now my phone is reseting once it starts I will confirm.:fingers-crossed::fingers-crossed::fingers-crossed::fingers-crossed:
Click to expand...
Click to collapse
yes it did stuck once or twice at the userdata erasing stage when I was putting up the new ROM but after some attempts,it never got stuck at any stage but even after successful installation, the problem existed...Now I have given my phone for repair and the store person said that there is some power issue in the board...its not an software isssue.
Chandu710 said:
my yureka when power on reboots means the YU logo pos and closes then again pops and closes...and when I power on my phone when charger is connected the phone starts perfectly everything works and when I unplug the charger it again powers offs..need a solution please help
Click to expand...
Click to collapse
Facing same problem ...any help guys...
Can you please update the further steps to do
Can you try to get into recovery mode? You need to understand a few commands of ADB also. Don't worry. Your phone will be working again. Remove the battery for a few seconds and put it back. Don't start the phone. First hold the volume up button and then at the same time hold the volume down button. Keep pressed both the buttons and then press the ON button ( All three buttons at the same time ). After your device vibrates a little and sows the YU Logo, let go of all the buttons......you should get into the bootloader menu. Tell me if you can do that. Will explain the steps further after you reply.[/QUOTE]
Yureka mobile is getting heated and gets switch off...and doesn't get ON. Screen shows Cyanogen all day...but its getting ON in safe mode...plz help to sort it out...