Related
My Atom has been working excelent for more than 6 months.
The problem is that when I try to charge it through the AC or a USB it doesnt charge anymore, the orange light doesnt turn on and the symbol in the phone turns only for a few seconds fron the battery into a wall plug, but then nothing...
I took out the battery and then charge it and worked but only when the device is off completely not when it is on or on stand by...
What can I do?
I just made a self diagnostic and when it gets to the part of the USB/AC Charging it says battery 100% charged (it passes the test) and that is not true, battery is at 18% right know
Same...
I have the same issue where my battery always shows as 100% even when you use it to 1% its still shows 100% and then it just quit when it runs out. Damn weird.... Just happened today and I only had the Atom Exec for 2 months... Any input would be much appreciated. Thanks!
Resolved
It was faulty battery not reporting correct capacity & usage.
I had a similar problem with my Atom. It could not charge the device from USB at first, then it got worse and stopped to charge from wall outlet. What I found out was that the connection plate at mini-USB port of Atom was worn out slighlty. I solved the problem by forcing usb cable connector into a mini-USB port, so it went further a bit (half a millimeter) and now everything is Ok - no problems to charge from either USB cable or wall charger.
I had the same problem, and found out that one pin in the mini usb socket bent downwards, fixed it myself and now its working fine
ozamalloa said:
My Atom has been working excelent for more than 6 months.
The problem is that when I try to charge it through the AC or a USB it doesnt charge anymore, the orange light doesnt turn on and the symbol in the phone turns only for a few seconds fron the battery into a wall plug, but then nothing...
I took out the battery and then charge it and worked but only when the device is off completely not when it is on or on stand by...
What can I do?
Click to expand...
Click to collapse
Mate! You gotta bring it to the SC... Its the fuse. The charging loop gose through the fuse and since it doesn't charge - most likely its the fuse (yo can test it with the normal tester...) If its not the fuse, it can be either of two - UEM Chip (Universal Energy Managmnt) or your PA (power amp). You can test it by measuring the resistance on the very left contacts of the battery ON YOUR PHONE! If the resistance close to 1 - its PA...
Wouldn't recomend to replace it yourself... Go for repair centre.
It's going to be a loose USB connection...
I did it on mine a while back, you have to hit the patch cable fitting in vigorously to the unit, and then from that day forward, no problems with charging!
Clean battery + phone><batt contacts if that makes you happy (it made me reassured)
G
Not sure if this is right part of forum, but here it goes.
I am having an issue with the charging of my O2 XDA Mini.
If my battery dies, with still a small bit of power left in it (enough to get splash screen) and I go to charge it works fine no problem. Now over the wkend my phone died on my and I left it till this afternoon when I tried to turn on, it wouldnt turn on at all (not even splash) because obviously the battery is completely dead. Now when I go to plug it in, it wont charge, from USB cradle, the little orange light to say that its charging doesnt even come on.
Last time this happened I eventually got it to work via a friends socket (plug) charger, rather than USB, charger. Is there any reason for this or anyway that it can be fixed that even when the battery is completely dead I can charge it from my USB cradle.
Any help would be apreciated.
Thank you in advance
Rattlehead
Sorry to bump this, but does anyone have any idea. I beleve the cause of this is due to the fact the USB power from the PC isnt enough to get the charging process started, is there anyway to get this done via the cradle.
Thanks
Rattlehead
You'll need to use a charger that plugs into a wall socket I'm afraid. This happened to me once & that was the only way I could get it to work. If you search on Google, you'll find methods that involve a stripped down usb cable, but a wall charger is definately easier.
Good luck.
Should any usb based wall charger work?
I have a Motorolla one and Ive tried that but that didnt work.
I know for a fact that when I use my friends one it works and will charge, but he aint round for another 2 weeks
Poop
Rattlehead.ie said:
Should any usb based wall charger work?
I have a Motorolla one and Ive tried that but that didnt work.
I know for a fact that when I use my friends one it works and will charge, but he aint round for another 2 weeks
Poop
Click to expand...
Click to collapse
You cannot charge a totally flat battery through usb cable using PC,cuz it only supplies 0.5(500)amp,whereas to get the dead battery back into charging,it requires a supply charge of 1.0(1000)amp,secondly you can only charge the phone via usb if it's working normal and not when it's dead,as you cannot boot into OS.
Therefore,it'll only start to charge with a 'Wall Charger' which only supplies 1.0 amp,your friend's Wall (Mains) charger must be suppling a 1.0 amp charge.You cannot even charge it with the Motorola usb charger cuz it also supplies only 0.5 amp.So try to get a Wall (Mains) charger to get it start charging.
OR,
Yes! you can Jump start the battery using Motorola charger,but you'll have to sacrifice the motorola charger to do it,as you'll have to cut off the usb plug of the charger cable end and attach the 'Red' wire to the '+' (Possitive) connector of the battery and black wire to the '-' (Negative) connector of the battery and give Shock Charge to the battery for 10 seconds,repeat this for 4/5 times,it'll give the battery a jump start and will increase the 'Pulse' level of the battery,after that put it in the phone and check if it loads up,if it does then you can charge it via usb cable connected with PC.
Good luck
BTW ! there's an excellent thread regarding charging to avoide the battery to go flat and saving from getting into this situation,it wud be very info for you,check it also :-
http://forum.xda-developers.com/showthread.php?t=342162
Cheers
zabardast_1 ,
You are the Guru ~
sorry couldnt reply to you before now, zabardast_1 thank you so much.
Thats great will have a look tonight and see what I can do
Here is a simple way of solving the problem, go and buy a charger, they cost next to nothing.
Hello. I've bought today broken Typhoon. It doesn't turn on, but when i connected cables to the battery and then put battery in and hold a switch, red light appeared under the power button and sometimes display lighted white. When i'm plugging in charger, red light under the power button also appears. Any ideas, how is it broken? what should i do to repair it? help me please
which charger? the one that plugs into the wall or a usb cable that plugs into your computer? If it's into the computer, or not the wall plug that came with the phoen, then it's possible your battery is completely drained dead. When the battery is extra super low, the usb and some other chargers don't have the juice to charge it. You have to have the right wall plug charger i've found.
i'm hopin that's the thing....plug it in, charge it for a bit then try again. Also, once you get juice in there, plug it into the usb port on your computer and hit the camera button. that should jack it into the boot loader mode.
Li Ion
nosaturn said:
which charger? the one that plugs into the wall or a usb cable that plugs into your computer? If it's into the computer, or not the wall plug that came with the phoen, then it's possible your battery is completely drained dead. When the battery is extra super low, the usb and some other chargers don't have the juice to charge it. You have to have the right wall plug charger i've found.
i'm hopin that's the thing....plug it in, charge it for a bit then try again. Also, once you get juice in there, plug it into the usb port on your computer and hit the camera button. that should jack it into the boot loader mode.
Click to expand...
Click to collapse
The batteries do die totally over time especially if they are charged from part full and never allowed to totally discharge. Do the do as described and if that doesn't work there are 10 on UK eBay right now one with 256Mb card for £25.00, you can't say fairer than that
Battery is too low in order to initialize the charging process.
Just plug in and plug out the wall charger until the LED turns orange.
hi there.
shortly-i have this phone with no orig. usb cable and with no wall charger. it was friend of mine phone actualy. given to me with dead battery (i am not sure but i have trouwn it away long time ago)
first I did was to wait until friends of mine from china had sent to me 2 batteries compitable with the phone. what i discovered is that a normal ordinar usb cable cant charge the phone's battery it only can connect to the pc.
second what i did is this: i found my old charger from a very old panasonic cell phone and had a try to make the charging process with the simply contacting corresponding pinouts of the battery to the +&- of this same charger (somehow i dissasembled the plug of that charger and it became more "comfortable" to get in touch to the pinouts of the specific cingular's battery)
that unordinar way i did discovered that i can charge these batteries even not sure how much appropriate that other brand wall charger is. It seems its pretty much the same as a power characteristics.
Meanwhile (as i dont use this phone) i had some free time to search the net and to have better idea about that strange unordinar power charging matter with that model of a phone. The situation is that i cant find a place nearby me to buy a cheap usb and wall charger and become using this nice device finaly.
And also i dont want to buy these cable things before clearly understand why this happens ..
I did try also to charge this phone with a HTC brand wall charger but no sucsess again cause it seems this wall charger is for other htc phone (even same mini usb plug and same characteristics)
What i need is to have answers by someone very informed about that matter and let me know what exactly is the specific power charging matter (need explanations i mean) with this phone. If sharing some good ideas about how to remake others usb cable or wall charger for geting it work along for me in such a case , i will appreciate this very much
thanks
charge
hi ! please forgive me for my bad english! in this case you can charge your phone in 1 way! you need to procure a motorola or any charger with same socket but attention the charger must have 6 volts and no less than 500 mAh(milli amps)! you cut the wires and one wire put on the + of the battery you will see the signs on the battery an one wire at the - no matter which one. and you need stay with the wires 3 - 4 minutes on the battery ! then you put the battery on the phone it will start and then you cand fully charge it with the usb cable ! good luckk ! i hope my inf will help you!
no
no it doesnt work that way.
what i need is the simple answer : what is so special into the pinouts of htc cingular 8125 wall charger?
thats what i need only. Then I might figure out how to proceed
Thanks anyway
I don't know if anyone else has had trouble doing what I have done, but I've got the Cingular 8125 (HTC Wizard 100), which is also known as the HTC 8125.
1. I bought a car charger at a convenience store for $6 that had the mini-USB plug. It worked like a charm. Never any problem there.
2. I also bought a standard USB to mini-USB cable from the local computer store, because I had lost mine, and it also worked fine for both synchronization and for charging.
3. I bought a second wall charger, buying a standard mini-USB wall charger sold pretty much everywhere cellular phone chargers are sold. It's a common charging port, and this generic worked for me as well.
I'd be interested to hear if anyone has had problems with these types of devices not properly charging the unit.
Even my USB cable for my portable USB hard drive will power my unit.
EDIT: About your problem with it not charging. I had that problem about a year ago, when my battery got extremely old. It wouldn't charge even with the original charger. I just needed a new battery. The batteries get old and stop taking a charge after a certain amount of use. How long this takes depends on how heavily the batteries are used. They, like car batteries, do not last forever.
I had this problem when I had my wiz too. The battery died and drained, and my phone refused to charge it. I took it to an AT&T service center, and they had no clue what the problem was, and they wanted to issue me a replacement (it was a G4, I had a G3, I wasn't about to fiddle with that at the time.) So I asked to borrow a demo device they had there to fix it. I charged my battery on their demo device no problem, got it up to 3%, and finished charging it through my USB cable in the car socket.
It appears to be a sort of one-in-every-few-or-so type condition, but I got hit with it.
seems like noone can tell me if something special inside the mini-USB plug.
i realy cant charge. Very nice device, but i cant make it charging up whit cables.
guys, from up there, say that nothing special about the charging cables, but i trust what i see not what i read.
Perhaps there is a problem with your USB port on the device? USB charging has standards, and all devices that need power from a USB port have the same power pin configuration. Otherwise, they can't call it a USB connection. It would have to be called a proprietary connection, and they would have to change the plug size/dimensions and pins.
If there isn't a problem with your battery (which is the most likely source of your problem), then it may be a loose connection on your USB connector. This happens with a number of devices.
If a sync cable connects to the PC but will not charge the battery, then you definitely have an unusual pin detachment of some sort, or a bad battery.
thanks again..
for pity i was writing a lot to make my recent post and finaly it desapeared cause my session was left.. its funny in some case, but now i just dont want to repeat all what was intended to be posted
i give only the link where you might see why i was assuming that this is a kind of a special matter here with that htc 8125 charging
//pinouts.ru/CellularPhones-A-N/razrv3_charger_pinout.shtml
so, any more help will be appreciated a lot
thanks
SOLVED: HTC Wizard (Cingular 8125) Dead Battery Wont Charge
Dozzen said:
hi ! please forgive me for my bad english! in this case you can charge your phone in 1 way! you need to procure a motorola or any charger with same socket but attention the charger must have 6 volts and no less than 500 mAh(milli amps)! you cut the wires and one wire put on the + of the battery you will see the signs on the battery an one wire at the - no matter which one. and you need stay with the wires 3 - 4 minutes on the battery ! then you put the battery on the phone it will start and then you cand fully charge it with the usb cable ! good luckk ! i hope my inf will help you!
Click to expand...
Click to collapse
Hi - Too bad for the OP that asked questions but did not listen to this brilliant post.
I have confirmed that a variation of this method works perfectly! I have an old Cingular 8125 that I have been trying to charge for over a year using various USB chargers and NONE would charge the device.
The reason that this may happen is that the original charger has an output of 1 full amp which is much higher than most chargers. The voltage is the same but you need a charger that can handle such a strong current draw.
Nearly all USB chargers can only handle around 250milliamps - 500milliamps which is about half the power needed to breathe life into a fully discharged battery.
The best solution is to NEVER let the battery fully discharge.
Here are the details of what I did:
1. Find the best match charger of 5-6 DC Volts and ability to put out as close to one amp (1000mA) as possible. I chose an old Sanyo SCP-07ADT that is rated at DC 5.4V at 800mA. The plug can be any type, no need to be USB.
2. Cut the connector off the end of the cable and strip the outer black part up about an inch and then strip the positive and negative (red / black respectively) wires up about a millimeter, just enough to have bare metal ends to touch to a small area.
3. Take your battery out of the phone, look at the back of battery for the + and - marks which correlate to one of the metal connection points on your battery, this is where you will "touch" or "attach" the bare ends of the wires.
4. Plug the charger in making sure not to short your bare leads. Before you do this double check that the OUTPUT of your charger is indeed DC voltage so that you don't hurt yourself. You do not want AC output and it can be dangerous.
Then touch the bare end of the red wire to positive of battery, and black wire to negative terminal of your battery. I held them with my fingers while surfing the web for about five or ten minutes. I had no idea if anything was happening or not but it "felt" like the battery might have gotten just a bit warmer.
5. Unplug the home-made bare wire charger and put battery in your phone. Quickly attach a USB charger or just plug into a USB cable of your computer. I pushed it in and nothing happened at first but finally I heard the standard "bleep" when you plug a USB device in. I knew that I made progress because it never beeped before it took about 30 seconds and several "bleeps" of connecting/disconnecting from USB but eventually the charge light stayed on!
It's been about 30 minutes and I'm up to about 50% charge and been using the phone heavily while charging.
So, in summary... never let your battery discharge below 5% or you can only charge it with an OEM cable rated at 1amp (rare). IF you let it discharge to "dead" then charge for 5-10 minutes with the "wire" method and then charge normally!
Thanks to Dozzen for the original idea!!
Wizard that won't charge
When my Wizard/HTC 8125 goes dead my cure for the battery is to use a 9 volt charger with the wires stripped back also. But, my method is a bit different. I place a standard Christmas Tree light bulb (the newer small ones)in series with the charger wires. Observe the correct polarity. The battery is labeled + and - so that part is easy. By using the small light bulb you are doing 2 things. 1.You can see the slight glow from the bulb and know that proper connection is made. 2. You are limiting the charging current to the battery.
If you get really creative like I did you can solder a couple of small nails or in my case a set of red and black probes to the setup and the points on these nails/probes make for much easier connections. Note.... This method may take a few minutes longer but, is much easier on the battery.
In my experience once the battery is below a certain level NO charger that I plug in will work. I just purchased a used 8125 from eBay and brought it back to life most successfully with this method.
hy there my htc wizard battery whos dead so i charched with a cable with + and - the phone starts but when i try to connect to a usb or a adaptor it doesnt charge anymore it show me the charge icon on the baterry but it doesnt charge the usb works fine it's sync to my pc but it doesnt charge anymore... what sould i do?
So it seems no one touched on what really matters here.
A design flaw, in my opinion. The HTC Wizard cannot recharge via USB unless there is enough power to turn on. The reason is because it requires the OS to charge.
So, what many people already posted are very creative ways to charge your 8125. The easiest and cheapest way, in my opinion, is to use AA batteries.
1) Take two AA batteries and tape together so they are in series. Imagine it like this... [- AA battery #1 +][- AA battery #2 +]
2) Use two wires and tape one to each side of the AA's (one on the + side and another on the other battery's - side since the - of the first battery is connected to the + of the second).
--w-i-r-e--[- AA battery #1 +][- AA battery #2 +]--w-i-r-e--
3) Connect the positive (+) wire to the positive (+) side of the phone. By this I mean the 6 metal pieces that stick out to contact the phone battery. I did it by wrapping the wire around the top most one (or second top most, it's been over a year since I've done this.).
4) Connect the negative (-) wire to the negative (-) side of the phone. Again, bottom most or second bottom most (see #3).
5) Insert phone battery while the wires are still in and connected to the two AAs.
6) Let the power flow for 30 seconds or so and then try turning your phone on. This part is the important part because you cannot use a USB to mini-USB connected to your computer to charge the phone unless the operating system can function. Meaning, it needs to be turned on first.
7) Once the phone is on, plug in the mini-USB part and connect it to a computer. I'd recommend getting at least 5% battery before disconnecting the AAs, seeing as you need to be able to start up your phone long enough for the OS to boot. Once the OS boots, you can fully charge it through a normal USB to mini-USB connection on any computer.
old post but just wanted to say thanks. Used the wire to battery method and got phone turned on after 2 mins of holding wires to battery.
Totally stock (but i don't think it matters).
Plug the phone in, orange LED comes on.
Hold it or place in on the counter five seconds later, LED is off.
Had the phone since 6/4.
Anyone else having issues?
Are you using the AC charger ? I have two Evos and one of the chargers does what you are describing. The orange LED comes on and then goes off after a while and the phone stops charging. Does it on both phones, the other charger works fine with both usb cables.
Are you using the USB charger with a computer or laptop or plugging straight into the wall with an AC charger?
This does make a difference because if you are charging with a USB + laptop combination you could be suffering from the computer going to sleep and disabling the USB ports power to conserve laptop battery life. If you are having the issue when plugging into the wall, try plugging into a computer and selecting the "Charge Only" option when your USB debug comes up. Once it does this, allow it to charge for a period of time and then turn the phone off, switch to AC power plug and see what happens.
Perhaps you had some kind of over voltage spike on the charger through the AC plug. I could see it possibly tripping something in the phone to stop taking charge to protect the handset.
Also make sure if you do use a laptop, use a USB 2.0 or better port. More power and faster connection. Gotta love it.
Your charger may not be sourcing enough current anymore (for whatever reason). I have seen the exact same behavior with USB car chargers that were only sourcing 100-150mA.
Have you tried plugging the USB cable into a modern desktop PC? (Some laptops have reduced current ports, so a desktop is a safer bet)
Its definitely a current issue. I tried to charge my phone using my bluetooth headset's wall charger, but I got the behavior you are describing. The bluetooth headset's charger just doesnt put out enough current.
Are you using the charger that came with the phone? if so, you may want to exchange the charger...
im having the same problem when i connect it to my desktop, it sees it for about 2 secs n then disappears. My computer at work has no problem seeing the phone. i wonder if i need a driver or something for my usb ports, anyone have any ideas??
tarheelsmj12001 said:
im having the same problem when i connect it to my desktop, it sees it for about 2 secs n then disappears. My computer at work has no problem seeing the phone. i wonder if i need a driver or something for my usb ports, anyone have any ideas??
Click to expand...
Click to collapse
Probably not a driver issue, but that that rail from the power supply is either undervolted (say 4.6V instead of 5V), or can't provide enough current (amperage) or both. If I recall correctly, the Evo needs 5V @ 1A (+/- 3% tolerance).
Phone not charging
my phone has been charging fine since I got it... even been using the night desk clock app while sleeping at night for the alarm with it plugged in... everything was good...
With my phone about to die today, I plug it in to the wall charger, the led/batter indicator shows that it is charging... then POW.. it says I have a low battery and it needs to be plugged in... WTH??? it is plugged in!
The only thing I did today was flash the new boot.img for the cap fix over in Toast's thread...
Weird thing now is that I took my hero battery and put it in my EVO, plugged it into wall charger, and it stays charging... So, I put my EVO battery in my hero, plugged it in, and whola... it's now charging...
Please help as I am baffled.
MILH0U5E said:
The only thing I did today was flash the new boot.img for the cap fix over in Toast's thread...
Click to expand...
Click to collapse
that's your problem right there. that custom kernel is known to have charging issues.
I'm having the same issue with my car charger consistently. Plus my AC charger less consistently. For example, I'll go to bed and plug it in, the next morning I wake up and see the phone is at 80% charge and isn't charging. At some point over night, it gave up. This is with the stock charger too.