Hey guys,
finally i bricked my phone...
After a failed flash to TWRP recovery and a failed unbrick with fastboot, the phone won't start. Blackscreen. Only in device manager it show's "Qualcomm HS-USB QDLoader 9008". Is there any chance to unbrick or should i get a new mainboard?
PS: Sorry for my bad english, im from Germany
Thank you in advance
JaDa
@JaDaKiZz welcome to the party - read this http://www.reddit.com/r/lgg2/comments/2p5xei/the_lg_g2_is_unbrickable_a_story_of_death_and/ and let me know if you need any help. The MOST IMPORTANT thing you need to do is figure out the right KDZ for your phone.
Use http://csmg.lgmobile.com:9002/csmg/b2c/client/auth_model_check2.jsp?esn=xxxxxxxxxxxxxxx
replace xxxxxxxxxxxxxxx with your IMEI
Hey sandys,
the BoardDiag start but abort the test.
Linux don't show my G2 in devices. What can I do?
JaDa
Same thing happened to my phone. Thats what it shows in windows and isnt picked up by ubuntu. When I tried to use the lg tool to recovery it fails and says phone isnt in dload mode trying flash programmer. Dont have the money currently for @tungkick and dont see any other way.
How to Fix "error device not found in dload trying flash programmer" when use boardiag .
Lg g3 qualcomm 9008 when install driver then use tool boardiag fake tool say device not found in dload trying flash programmer
when you use tool fake board share in xda another tool say device not found in dload trying flash programmer. You need remove battery (of lg g2 hold power 1 minute) then connect cable again and use tool again
Sure install driver 100% wrong
With windowns 64 bit you need restart pc then click f8 choose disbable driver singturne....
Then remove battery (hold power 1 minute with lg g2) then connect cable try use tool unbrick >> sure done 100%
I will updload video error dload
Remember disbbale tool sony erricson if you have open tool in taskbar
How to fix “No response from the device. Check PMIC first and
if still boot problem, replace AP.”
Remove battery and connect again put qualcomm 9008 then use tool in topic
http://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-all-variants/ Just as helping
[*]I see very topic unbrick qualcomm 9008 lg g2, lg g3 but all tool can not use.
I have full tool board ver 2.9.( only 2.9).
Link download drive.google.xxx /file/d/0B_Hol5T47S-bYjNETmVPZkdWUms/view?usp=sharing (xxx= com)
Support lg g2, lg g3 workking 100%.
Download tool, open BoardDiag and choose file tot correct model phone of you( you can download tot in xda)
See guide in pictrure : very easy.
Note
Hold power 2 minute and connect cable ( or remove battery)>>And open tool check ap, emmc test again
Then unbrick done remove cable, hold power 30 second and hold volume up connect cable phone put downloadmod >> Use lgflashtool 1.5 flash file tot again >> done.
If done pls donate a few beers paypal of my Thank you very much.
Man you saved my ass Thank you so much !1 when i get my salary ill donate to you and tell everybody to do so cuz this tool is amazing. im in download mode now ill try to flash with lg flash tool.
Thank so much man but my g3 last week unbrick qualcomm i had I submit for warranty[emoji24] [emoji24] I am very Star-crossed [emoji20]
Hello friend willcracker
Hello friend willcracker :good:
I hope all is well;
I saw this little tutorial so I want to ask for help
I have a LG G3 D855p and my phone is dead (bricked)
I can not quite understand the method you friend
not turn on my phone
I can not enter the "" Download Mode ""
VOL + Up when I connect the USB cable to the PC recognizes me as:
Qualcomm HS-USB QDLoader 9008 (COM10)
why I ask for help to revive my g3
If you help me ... .. I promise to donate something for you
you send a file "picture" attached
- - As I can get to "" Fastboot Mode "" on my phone
I hope your prompt response, please do not ignore my message :crying:
greetings from peru
You need to Disassemble Phone and Expose the TP Location
See pictrue
Expose the TP Location.
Done phone put qualcom 9008>> use tool unbrick
Remeber unplug battery connect only cable and short testpoint
Thanks for responding, but I need your help please friend
Hello willcracker I have no such tool you indicate "tool unbrick testpoint"
I could do this step with some type of cable or wire?
- If you Might tell me how to do that step with another option
leave your email. to chat google chat (Houngts) and you help me please
I'm worried because my g3 d855p not light, or anything like I said ....
await your prompt response, I hope you can help me
TOT Firmware, must match installed version?
Hey, thanks for providing this tool!
Final question, the TOT file must this match the installed version?
My situation:
Lollipop was installed, goal was to move to a custom rom (blisspop v2.3)
Rooting was successful
Install of twrp not, reboot into recovery caused the 'signature verification error'
Tried to flash the kitkat rom via the download method, failed, ...
Currently, I have the same verification error also when trying to get into download mode and have the Qualcomm HS-USB QDLoader 9008 in my device manager.
I have the LGD855AT-00-V10e-EUR-XX-JUL-08-2014-16G+0.tot file and did the first step of your procedure. Can I do the second step with this extract of kitkat even if lollipop was installed?
any feedback greatly appreciated!
Hello willcracker thanks, thanks for reply but I need your help please
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
**will commit without any error.
And haci get my phone g3 ... haci I could also help others or siblings who need help to solve any problem with the g3
- I can not enter download mode
- I can not enter recovery mode
- When I turn on my phone, get the LG logo goes about three letters at the top left, then flashes a red, blue lights ...
- The PC recognizes me as Qualcomm HS-USB QDLoader 9008 (COM10)
You could leave your email. Google to chat chat (Houngts) and help me please
*....
Waiting for your prompt response, I hope you can help me
Please do not ignore my message willcracker friend
Greetings from Peru
themusic1510 said:
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
Greetings from Peru
Click to expand...
Click to collapse
NO you need find google how do short testpoint samsung n7100 you see they guide short testpoint . Lg when short testpoint phone detect qualcomm 9008
And you use tool board diag unbrick.
???
themusic1510 said:
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
**will commit without any error.
And haci get my phone g3 ... haci I could also help others or siblings who need help to solve any problem with the g3
- I can not enter download mode
- I can not enter recovery mode
- When I turn on my phone, get the LG logo goes about three letters at the top left, then flashes a red, blue lights ...
- The PC recognizes me as Qualcomm HS-USB QDLoader 9008 (COM10)
You could leave your email. Google to chat chat (Houngts) and help me please
*....
Waiting for your prompt response, I hope you can help me
Please do not ignore my message willcracker friend
Greetings from Peru
Click to expand...
Click to collapse
I'm in the same boat! Could you please explain it a little better?
frank.devliegher said:
Hey, thanks for providing this tool!
Final question, the TOT file must this match the installed version?
My situation:
any feedback greatly appreciated!
Click to expand...
Click to collapse
You need extract file tot d855 and put phone to qualcomm 9008 and unbrick . DOne flash stock rom. Find rom 5.01 link another
Ahh now i see!
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
@willcracker
The link doesnt work !? Where can i download the BoardDiagTool?
I have a F240L and this totfile BIN_LGE980AT-00-V20g-ATT-US-APR-28-2014+0 .Can I use it?
I have tried with this file but i get the message AP Check or Check PMIC first
sourly64 said:
@willcracker
The link doesnt work !? Where can i download the BoardDiagTool?
I have a F240L and this totfile BIN_LGE980AT-00-V20g-ATT-US-APR-28-2014+0 .Can I use it?
I have tried with this file but i get the message AP Check or Check PMIC first
Click to expand...
Click to collapse
what do you mean?
The link unbrick only g2 g3 and gpro2
Phone of you G pro i not upload tool . Unsderstand.
Magnerion said:
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
Click to expand...
Click to collapse
Model Lg d851? writh
rememer ber tool suppoer only lg g3 f400s/l/k , lg d855 16gb and 32gb.
If use tool say error pcmic on tool not support (Ex: lg d851)
I up load only msm8974ac g3 msm8975ac g3 no upload
Magnerion said:
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
Click to expand...
Click to collapse
It seems won't work.I have gone through about this problem.Alway AP Check fail.QPST reported that phone had been in Sahara download mode for few seconds.A RMA fix my phone.But it cost me about 50dollars
willcracker said:
what do you mean?
The link unbrick only g2 g3 and gpro2
Phone of you G pro i not upload tool . Unsderstand.
Click to expand...
Click to collapse
Hello willcracker !
Thanks for the note,do you know the totfile is the right one ?
I get with this file ,when is extraced the message in BoardDiag Check PMIC first and if not boot Check AP
TOT Version
willcracker said:
You need extract file tot d855 and put phone to qualcomm 9008 and unbrick . DOne flash stock rom. Find rom 5.01 link another
Click to expand...
Click to collapse
I have a TOT file, but for kitkat, not Lollipop. Can I use this TOT file?
(have only a kdz file for lollipop)
Thx!
frank.devliegher said:
I have a TOT file, but for kitkat, not Lollipop. Can I use this TOT file?
(have only a kdz file for lollipop)
Thx!
Click to expand...
Click to collapse
YES you can use tot kikat unbrick .
sourly64 said:
Hello willcracker !
Thanks for the note,do you know the totfile is the right one ?
I get with this file ,when is extraced the message in BoardDiag Check PMIC first and if not boot Check AP
Click to expand...
Click to collapse
sr i have not upload hex lg gpro waitting comming soon.
I have hard-bricked my xperia l to the point that it shows no leds and is completely life-less.
Anyone with the proper knowledge of QPST and unbricking the device using the Qualcomm HS-USB QDLoader 9008 mode, PLEASE PM ME!!!
Urgent help required.
Thanks in Advance.
Hey find a stock rom specific for phone and flash it using pc or if u can access ur recovery mode. Hope this help or head straightaway to sony authorized centre
you can make the 8x30msmimage.mbn out of stock firmware + QPST. You can't make the hex, it is probably carrier key specific. Qualcomm bootloader signature verification strikes again.
nxb said:
you can make the 8x30msmimage.mbn out of stock firmware + QPST. You can't make the hex, it is probably carrier key specific. Qualcomm bootloader signature verification strikes again.
Click to expand...
Click to collapse
is there any guide to create mprg8226.hex and 8226msiimage.mbn
you won't be able to make the hex. look on how to create 8960 mbm its probably the same for this chip too.
Same problem here. I was just looking for a way to get atleast the fastboot and flashmode working again. Any advice?
does anyone know how to unbrick a hard-bricked zte blade g v880g? it has Qualcomm Snapdragon S4 Play (MSM8225) prossesor.
ntouris3 said:
does anyone know how to unbrick a hard-bricked zte blade g v880g? it has Qualcomm Snapdragon S4 Play (MSM8225) prossesor.
Click to expand...
Click to collapse
Thread moved to proper forum
If you can get the thing to go into fastboot (by pressing whatever button combination is appropriate for your specific device) and provided you have a backup of the partitions you damaged you can use fastboot to reflash the damaged partitions.
Google search for "[Guide] de-bricking a ZTE Blade - ZTE Blade / Libra ROMs & ROM" that will have various scenarios for debrikcing.
well... I didn't manage to get into fastboot but I managed to download a flasher! I connected my phone and it started installing things but it always stuck on ''wait reset''................................
ntouris3 said:
well... I didn't manage to get into fastboot but I managed to download a flasher! I connected my phone and it started installing things but it always stuck on ''wait reset''................................
Click to expand...
Click to collapse
Sometimes it is necessary to erase flash partitions before flashing them ... not sure if this is your issue but be warned that you could make things worse by doing so.
Can your phone start into ant of the other modes: recovery, field test or download mode ? if is can make sure you don't further damage the relevant partitions + the boot loader and whatever is used before the boot loader.
I've a snapdragon 600 based devel board and there are 2 stages of primary boot loader before LK ... not sure for your soc but make sure you don't dammage them if they are OK.
My is is hard bricked... I cant get into any mode... The only thing i can do is just to connect it to my pc ... And it is recognized as forge hs-usb qdloader 9008..... I found a program at androidbrick.com that may help but i cant use it because it is protected with a pssword that i dont know...
ntouris3 said:
My is is hard bricked... I cant get into any mode... The only thing i can do is just to connect it to my pc ... And it is recognized as forge hs-usb qdloader 9008..... I found a program at androidbrick.com that may help but i cant use it because it is protected with a pssword that i dont know...
Click to expand...
Click to collapse
I see people asking for the password on their forum ... regiter yourself there and ask for the password like the other users. If I knew it I'd give it to you
I'm not allowed to post links ... I'd point you to the url where people are asking for the password if I could.
Try searching with google : "Ultimate Qualcomm Snapdragon Unbrick Guide"
Thank you really much!
Sent from my Q8H-V1.0 using XDA Free mobile app
i need flash files for SP tool or files for MiFlash tool, for ZTE BLADE G V880G .
my phone not responding. there is not boot , recovery....
PC device menager see my phone like Qualcom HS-USB QDloader 9008 (COM5)
Thanks
sinbaj said:
i need flash files for SP tool or files for MiFlash tool, for ZTE BLADE G V880G .
my phone not responding. there is not boot , recovery....
PC device menager see my phone like Qualcom HS-USB QDloader 9008 (COM5)
Thanks
Click to expand...
Click to collapse
Mine too but i dont think you can flash via Sp tools this phone because its qualcomm not mediatek!
i used QPST and QXDM tool for unbreak the phone but i need flash files.:crying:
I find BIN file for full flash. zte_v955_full_riff.7z :angel:
which program i can use to flash with BIN file?
Im stuck there too bro
Qfil files for ZTE Blade g v880g ??
My Nothing Phone is hard bricked and not working.
No Fastboot Mode
No Recovery Mode
Mobile in Dead Condition.
Nothing Phone 1 Firmware do not have emmc, raw program and patch file.
I own a heavily Bricked Nothing Phone 1. Currently, I am trying to bring it back to life. It is detected as Qualcomm HS_USB QDLoader 9008 (Com3). After spending some time online, i got a possible solution, flashing it using QFIL. I downloaded the firmware, it didn't have 3 files needed to start the flash process which were raw program XML file, patch file, prog emmc file. I looked up Online for these file specifically, But found nothing. Do anyone know what should I do.
I'm interested in this too! EDL Firehose saved my butt twice already. Would be great to have a saviour after an incredible eff-up on this phone.
If I can help in any way, let me know. The QPST tools and COM driver are installed, and can put my working phone in EDL for testing.
up on this post.
me be nothing phone is nothing
my phone now restart problem all i know sulotion already try in try but the same problem
iqcuratorhub said:
My Nothing Phone is hard bricked and not working.
No Fastboot Mode
No Recovery Mode
Mobile in Dead Condition.
Nothing Phone 1 Firmware do not have emmc, raw program and patch file.
I own a heavily Bricked Nothing Phone 1. Currently, I am trying to bring it back to life. It is detected as Qualcomm HS_USB QDLoader 9008 (Com3). After spending some time online, i got a possible solution, flashing it using QFIL. I downloaded the firmware, it didn't have 3 files needed to start the flash process which were raw program XML file, patch file, prog emmc file. I looked up Online for these file specifically, But found nothing. Do anyone know what should I do.
Click to expand...
Click to collapse
QFIL file for Nothing Phone is totally different compared to ROM firmware . You can't flash it . For unbrick the phone you must have this particular QFIL file which I don't think you find it online for now .
If by any chance you find it please share .