Database Users

Blackscreen / Qualcomm HS-USB QDLloader 9008

Hey guys,
finally i bricked my phone...
After a failed flash to TWRP recovery and a failed unbrick with fastboot, the phone won't start. Blackscreen. Only in device manager it show's "Qualcomm HS-USB QDLoader 9008". Is there any chance to unbrick or should i get a new mainboard?
PS: Sorry for my bad english, im from Germany
Thank you in advance
JaDa

@JaDaKiZz welcome to the party - read this http://www.reddit.com/r/lgg2/comments/2p5xei/the_lg_g2_is_unbrickable_a_story_of_death_and/ and let me know if you need any help. The MOST IMPORTANT thing you need to do is figure out the right KDZ for your phone.
Use http://csmg.lgmobile.com:9002/csmg/b2c/client/auth_model_check2.jsp?esn=xxxxxxxxxxxxxxx
replace xxxxxxxxxxxxxxx with your IMEI

Hey sandys,
the BoardDiag start but abort the test.
Linux don't show my G2 in devices. What can I do?
JaDa

Same thing happened to my phone. Thats what it shows in windows and isnt picked up by ubuntu. When I tried to use the lg tool to recovery it fails and says phone isnt in dload mode trying flash programmer. Dont have the money currently for @tungkick and dont see any other way.

Unbrick lg g3 qhsusb_bulk, qualcomm 9008 workking 100% by board ver 2.9a

How to Fix "error device not found in dload trying flash programmer" when use boardiag .
Lg g3 qualcomm 9008 when install driver then use tool boardiag fake tool say device not found in dload trying flash programmer
when you use tool fake board share in xda another tool say device not found in dload trying flash programmer. You need remove battery (of lg g2 hold power 1 minute) then connect cable again and use tool again
Sure install driver 100% wrong
With windowns 64 bit you need restart pc then click f8 choose disbable driver singturne....
Then remove battery (hold power 1 minute with lg g2) then connect cable try use tool unbrick >> sure done 100%
I will updload video error dload
Remember disbbale tool sony erricson if you have open tool in taskbar
How to fix “No response from the device. Check PMIC first and
if still boot problem, replace AP.”
Remove battery and connect again put qualcomm 9008 then use tool in topic
http://www.androidbrick.com/unbrick-recover-your-dead-lg-g3-all-variants/​ Just as helping
[*]I see very topic unbrick qualcomm 9008 lg g2, lg g3 but all tool can not use.
I have full tool board ver 2.9.( only 2.9).
Link download drive.google.xxx /file/d/0B_Hol5T47S-bYjNETmVPZkdWUms/view?usp=sharing (xxx= com)
Support lg g2, lg g3 workking 100%.
Download tool, open BoardDiag and choose file tot correct model phone of you( you can download tot in xda)
See guide in pictrure : very easy.
Note
Hold power 2 minute and connect cable ( or remove battery)>>And open tool check ap, emmc test again
Then unbrick done remove cable, hold power 30 second and hold volume up connect cable phone put downloadmod >> Use lgflashtool 1.5 flash file tot again >> done.
If done pls donate a few beers paypal of my Thank you very much.​

Man you saved my ass Thank you so much !1 when i get my salary ill donate to you and tell everybody to do so cuz this tool is amazing. im in download mode now ill try to flash with lg flash tool.

Thank so much man but my g3 last week unbrick qualcomm i had I submit for warranty[emoji24] [emoji24] I am very Star-crossed [emoji20]

Hello friend willcracker
Hello friend willcracker :good:
I hope all is well;
I saw this little tutorial so I want to ask for help
I have a LG G3 D855p and my phone is dead (bricked)
I can not quite understand the method you friend
not turn on my phone
I can not enter the "" Download Mode ""
VOL + Up when I connect the USB cable to the PC recognizes me as:
Qualcomm HS-USB QDLoader 9008 (COM10)
why I ask for help to revive my g3
If you help me ... .. I promise to donate something for you
you send a file "picture" attached
- - As I can get to "" Fastboot Mode "" on my phone
I hope your prompt response, please do not ignore my message :crying:
greetings from peru

You need to Disassemble Phone and Expose the TP Location
See pictrue
Expose the TP Location.
Done phone put qualcom 9008>> use tool unbrick
Remeber unplug battery connect only cable and short testpoint

Thanks for responding, but I need your help please friend
Hello willcracker I have no such tool you indicate "tool unbrick testpoint"
I could do this step with some type of cable or wire?
- If you Might tell me how to do that step with another option
leave your email. to chat google chat (Houngts) and you help me please
I'm worried because my g3 d855p not light, or anything like I said ....
await your prompt response, I hope you can help me

TOT Firmware, must match installed version?
Hey, thanks for providing this tool!
Final question, the TOT file must this match the installed version?
My situation:
Lollipop was installed, goal was to move to a custom rom (blisspop v2.3)
Rooting was successful
Install of twrp not, reboot into recovery caused the 'signature verification error'
Tried to flash the kitkat rom via the download method, failed, ...
Currently, I have the same verification error also when trying to get into download mode and have the Qualcomm HS-USB QDLoader 9008 in my device manager.
I have the LGD855AT-00-V10e-EUR-XX-JUL-08-2014-16G+0.tot file and did the first step of your procedure. Can I do the second step with this extract of kitkat even if lollipop was installed?
any feedback greatly appreciated!

Hello willcracker thanks, thanks for reply but I need your help please
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
**will commit without any error.
And haci get my phone g3 ... haci I could also help others or siblings who need help to solve any problem with the g3
- I can not enter download mode
- I can not enter recovery mode
- When I turn on my phone, get the LG logo goes about three letters at the top left, then flashes a red, blue lights ...
- The PC recognizes me as Qualcomm HS-USB QDLoader 9008 (COM10)
You could leave your email. Google to chat chat (Houngts) and help me please
*....
Waiting for your prompt response, I hope you can help me
Please do not ignore my message willcracker friend
Greetings from Peru

themusic1510 said:
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
Greetings from Peru
Click to expand...
Click to collapse
NO you need find google how do short testpoint samsung n7100 you see they guide short testpoint . Lg when short testpoint phone detect qualcomm 9008
And you use tool board diag unbrick.

???
themusic1510 said:
Hello friend willcracker not have any of those tools indicated in its response = "testpoint tool unbrick"
I can do this step with some type of cable or wire
- I want you to guide me step by step how to perform the process
**will commit without any error.
And haci get my phone g3 ... haci I could also help others or siblings who need help to solve any problem with the g3
- I can not enter download mode
- I can not enter recovery mode
- When I turn on my phone, get the LG logo goes about three letters at the top left, then flashes a red, blue lights ...
- The PC recognizes me as Qualcomm HS-USB QDLoader 9008 (COM10)
You could leave your email. Google to chat chat (Houngts) and help me please
*....
Waiting for your prompt response, I hope you can help me
Please do not ignore my message willcracker friend
Greetings from Peru
Click to expand...
Click to collapse
I'm in the same boat! Could you please explain it a little better?

frank.devliegher said:
Hey, thanks for providing this tool!
Final question, the TOT file must this match the installed version?
My situation:
any feedback greatly appreciated!
Click to expand...
Click to collapse
You need extract file tot d855 and put phone to qualcomm 9008 and unbrick . DOne flash stock rom. Find rom 5.01 link another

Ahh now i see!
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?

@willcracker
The link doesnt work !? Where can i download the BoardDiagTool?
I have a F240L and this totfile BIN_LGE980AT-00-V20g-ATT-US-APR-28-2014+0 .Can I use it?
I have tried with this file but i get the message AP Check or Check PMIC first

sourly64 said:
@willcracker
The link doesnt work !? Where can i download the BoardDiagTool?
I have a F240L and this totfile BIN_LGE980AT-00-V20g-ATT-US-APR-28-2014+0 .Can I use it?
I have tried with this file but i get the message AP Check or Check PMIC first
Click to expand...
Click to collapse
what do you mean?
The link unbrick only g2 g3 and gpro2
Phone of you G pro i not upload tool . Unsderstand.

Magnerion said:
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
Click to expand...
Click to collapse
Model Lg d851? writh
rememer ber tool suppoer only lg g3 f400s/l/k , lg d855 16gb and 32gb.
If use tool say error pcmic on tool not support (Ex: lg d851)
I up load only msm8974ac g3 msm8975ac g3 no upload

Magnerion said:
Well ive tryed this guide with two different computers, but all i get is ap check failed, i do get into qualcomm mode and everything. Why does it fail!!? Am i doing something wrong?
Click to expand...
Click to collapse
It seems won't work.I have gone through about this problem.Alway AP Check fail.QPST reported that phone had been in Sahara download mode for few seconds.A RMA fix my phone.But it cost me about 50dollars

willcracker said:
what do you mean?
The link unbrick only g2 g3 and gpro2
Phone of you G pro i not upload tool . Unsderstand.
Click to expand...
Click to collapse
Hello willcracker !
Thanks for the note,do you know the totfile is the right one ?
I get with this file ,when is extraced the message in BoardDiag Check PMIC first and if not boot Check AP

TOT Version
willcracker said:
You need extract file tot d855 and put phone to qualcomm 9008 and unbrick . DOne flash stock rom. Find rom 5.01 link another
Click to expand...
Click to collapse
I have a TOT file, but for kitkat, not Lollipop. Can I use this TOT file?
(have only a kdz file for lollipop)
Thx!

frank.devliegher said:
I have a TOT file, but for kitkat, not Lollipop. Can I use this TOT file?
(have only a kdz file for lollipop)
Thx!
Click to expand...
Click to collapse
YES you can use tot kikat unbrick .

sourly64 said:
Hello willcracker !
Thanks for the note,do you know the totfile is the right one ?
I get with this file ,when is extraced the message in BoardDiag Check PMIC first and if not boot Check AP
Click to expand...
Click to collapse
sr i have not upload hex lg gpro waitting comming soon.

Need mprg8230.hex and 8x30msmimage.mbn

I have hard-bricked my xperia l to the point that it shows no leds and is completely life-less.
Anyone with the proper knowledge of QPST and unbricking the device using the Qualcomm HS-USB QDLoader 9008 mode, PLEASE PM ME!!!
Urgent help required.
Thanks in Advance.

Hey find a stock rom specific for phone and flash it using pc or if u can access ur recovery mode. Hope this help or head straightaway to sony authorized centre

you can make the 8x30msmimage.mbn out of stock firmware + QPST. You can't make the hex, it is probably carrier key specific. Qualcomm bootloader signature verification strikes again.

nxb said:
you can make the 8x30msmimage.mbn out of stock firmware + QPST. You can't make the hex, it is probably carrier key specific. Qualcomm bootloader signature verification strikes again.
Click to expand...
Click to collapse
is there any guide to create mprg8226.hex and 8226msiimage.mbn

you won't be able to make the hex. look on how to create 8960 mbm its probably the same for this chip too.

Same problem here. I was just looking for a way to get atleast the fastboot and flashmode working again. Any advice?

My asus zc550kl full dead only showing in pc as QUALCOMM HS-USB QDLoader 9008

Hello,
My phone is Asus zenfone max-ZC550KL-16GB with 8916 cpu.
My phone's bootloader is damaged after flashing some .zip file.Now it's fully dead.
Not showing bootlogo,no recovery mode,no edl & no csc.It's just detecting as "QUALCOMM HS-USB QDLoader 9008 in PC.I downloaded QUALCOMM FLASH IMAGE LOADER(QFIL) but i can't find neccesary files for flashing(i.e., .mbn,rawprogram.xml,patch.xml suitable files for my phone's CPU).
Can anyone help me to unbrick my phone?

hi i,m facing this same problem i try my level best to flash stock os on it but it,s not turn on not charging no led lights indicates
a few weeks ago reverse charging popup is show again and again can,t see movie on the device to fix that i try to change the os
i just switch off the device from twrp after wipe dalvik ,catch and data the i try to turn it on but it,s not
if you find any way please inform me it,s very urgent ([email protected])

Christy2375 said:
hi i,m facing this same problem i try my level best to flash stock os on it but it,s not turn on not charging no led lights indicates
a few weeks ago reverse charging popup is show again and again can,t see movie on the device to fix that i try to change the os
i just switch off the device from twrp after wipe dalvik ,catch and data the i try to turn it on but it,s not
if you find any way please inform me it,s very urgent ([email protected])
Click to expand...
Click to collapse
You can't flash Stock ROM with TWRP, you should try flashing other ROM.

shirofficial said:
You can't flash Stock ROM with TWRP, you should try flashing other ROM.
Click to expand...
Click to collapse
hi my phone is total dead not charging not turning on no led indication i try my level best if u have a solution please inform me
because i don,t have a phone and don,t have enough money to buy a new phone

Idem... No solution?

Fix for dead ASUS Zenfone Max
Try holding down the power button and continuously press volume up (+) button. Hopefully this will take you to Downloader Mode.
---------- Post added at 04:45 PM ---------- Previous post was at 04:44 PM ----------
rkish0258 said:
Hello,
My phone is Asus zenfone max-ZC550KL-16GB with 8916 cpu.
My phone's bootloader is damaged after flashing some .zip file.Now it's fully dead.
Not showing bootlogo,no recovery mode,no edl & no csc.It's just detecting as "QUALCOMM HS-USB QDLoader 9008 in PC.I downloaded QUALCOMM FLASH IMAGE LOADER(QFIL) but i can't find neccesary files for flashing(i.e., .mbn,rawprogram.xml,patch.xml suitable files for my phone's CPU).
Can anyone help me to unbrick my phone?
Click to expand...
Click to collapse
Hold down the Power button and continuously press volume up(+) button, this will take you to download mode

rkish0258 said:
Hello,
My phone is Asus zenfone max-ZC550KL-16GB with 8916 cpu.
My phone's bootloader is damaged after flashing some .zip file.Now it's fully dead.
Not showing bootlogo,no recovery mode,no edl & no csc.It's just detecting as "QUALCOMM HS-USB QDLoader 9008 in PC.I downloaded QUALCOMM FLASH IMAGE LOADER(QFIL) but i can't find neccesary files for flashing(i.e., .mbn,rawprogram .xml,patch .xml suitable files for my phone's CPU).
Can anyone help me to unbrick my phone?
Click to expand...
Click to collapse
bro i too got in to this trouble after flashing stock in recovery ,a total dead , but its says that the qualcomm bulk loader port is for last chance of saving the phone ,and this is the qfil rom here {{{{{{ht tps://www .firmw are27 .net/2017/10/asus-zenfone-max-z010d-zc550kl-firmware .h tml}}}}}}}
but idk i cant reach in to those files ,bro u gotta check this out
check if its worked for u

https://drive.google.com/file/d/0B0ul1vuE3yJwUjVpSDJMbUJZanc/view
flash with qfil in 9008 mode

its for 8939

https://drive.google.com/file/d/0B0ul1vuE3yJwbTNScXhDYkx6cW8/view
for 8916

thanks bro ?? it worked bro , at last dead to alive

kichukic said:
thanks bro it worked bro , at last dead to alive
Click to expand...
Click to collapse
I am in same situation bro
While following these steps....
In QFIL, after clicking download
An error occurred,
Download failed: Switch To Emergency Download mode failed...
Google it and found to remove battery before connecting usb for lenovo phone.
Please help me... How you make it worked for non removable battery zenfone max:crying:

Yeah , many of em posting about it not recovering but some how mine has recovered with out any errors there , bro what about your cpu ??

krishnasmidhun said:
I am in same situation bro
While following these steps....
In QFIL, after clicking download
An error occurred,
Download failed: Switch To Emergency Download mode failed...
Google it and found to remove battery before connecting usb for lenovo phone.
Please help me... How you make it worked for non removable battery zenfone max:crying:
Click to expand...
Click to collapse
provide detail of ur phn ..
Sent from my Redmi Note 5 Pro using Tapatalk

kichukic said:
Yeah , many of em posting about it not recovering but some how mine has recovered with out any errors there , bro what about your cpu ??
Click to expand...
Click to collapse
Its asus zenfone max msm 8916. I have a feeling that is there any differnce in using windows 7 and windows 10??
What you guys are using while flashing with qfil? 64bit 86 bit are playing something??
---------- Post added at 09:50 AM ---------- Previous post was at 09:44 AM ----------
krishnasmidhun said:
Its asus zenfone max msm 8916. I have a feeling that is there any differnce in using windows 7 and windows 10??
What you guys are using while flashing with qfil? 64bit 86 bit are playing something??
Click to expand...
Click to collapse
Sometimes the error is firehose failed then on nxt couple of tries it is SDL fail
!!!

Well some times administration matters , on my first try i got a firehose error
Then i granted administration and everything goes well , if u got any error google those errors, thats what i did cause finding fixes for asus max is tough in xda especially which is in this condition

Hello,
I have similar problem with my ZC550KL. I downloded the 8916 firmware, but when I try to download usin qfil I got sahara fail message. Please share some brief instruction how to solve this.
Tnank you!

For all those who recovered there phone,does you last your IMEI number in the process??I lost mine,does your bootloader got locked

pranshaks said:
For all those who recovered there phone,does you last your IMEI number in the process??I lost mine,does your bootloader got locked
Click to expand...
Click to collapse
Do you have your efs?

Hello, I had a very little progress. I gave up about my asus zenfone max a year ago but glad that now looks like there's a hope in reviving my phone. I was able to download the right files to flash with QFIL. Most people here say that their PC detected QUALCOMM HS-USB QDLOADER 9008 but mine detect it as QUALCOMM HS-USB DIAGNOSTICS 9006. Due to excitement, I flashed it anyway and it created some memory partition on my hard drive whenever I plug the phone but QFIL gave me an error of :
** Download Fail: Switch To EDL Fail Failed to switch to Emergency Download Mode
I tried to google this error, some encountered it and was able to get a resolution by just removing the battery before plugging it in but our zenfone is with non removable battery. I have no luck yet. Anyone got suggestions ?

Qualcomm XT1766 Hard Brick Boost Mobile

Hey guys, I recently had an accident while trying to install stock firmware on my device. I tried to manually install a stock firmware ROM and in the middle of it the device just shut of. What I'm left with is a device which doesn't have fastboot or any other method of recovery other then through some qualcomm tools. The driver shows up as "qualcomm hs-usb qdloader 9008" on my computer. I tried following this guide https://www.droidsavvy.com/unbrick-qualcomm-mobiles/ and concluded that I'm stuck on the old hard brick and tried to follow the instructions but the problem here is that I don't think that I have the correct ROM file for QFIL because the firmware are zip files and not mbn as I think they are supposed to be. If anyone could help me with this in any way I'd really appreciate it, Thank you!

same as you man did you find a solution?

jesusloortega said:
same as you man did you find a solution?
Click to expand...
Click to collapse
https://forum.xda-developers.com/mo...766-unbrick-easy-sdcard-t3833408/post77427426