[q] need help install stock rom - Sprint Samsung Galaxy S 4 Q&A, Help & Troubleshoot

I am not an expert at installing ROMs on Android devices. I hope someone can help.
I have a Sprint Galaxy S4, SPH-L720. I have installed CM12 but now I would like to return to a stock ROM. I downloaded several from Sammobile. Now, I cannot install them.
I have tried several versions of ODIN. Attached is the message I get when trying to flash with ODIN 3.09. I have also tried to install from an SD card using CWM and TWRP with similar failure.
Any help will be greatly appreciated.
Code:
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUFNG2_L720SPTFNG2_L720VPUFNG2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!

laserman2431 said:
I am not an expert at installing ROMs on Android devices. I hope someone can help.
I have a Sprint Galaxy S4, SPH-L720. I have installed CM12 but now I would like to return to a stock ROM. I downloaded several from Sammobile. Now, I cannot install them.
I have tried several versions of ODIN. Attached is the message I get when trying to flash with ODIN 3.09. I have also tried to install from an SD card using CWM and TWRP with similar failure.
Any help will be greatly appreciated.
Code:
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUFNG2_L720SPTFNG2_L720VPUFNG2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Click to expand...
Click to collapse
You have a bad download
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Thanks for your response. I tried 5 different ROMs from Sammobile, all with the same results. I guess they could all be bad. Does anyone know of a good source for download?

laserman2431 said:
Thanks for your response. I tried 5 different ROMs from Sammobile, all with the same results. I guess they could all be bad. Does anyone know of a good source for download?
Click to expand...
Click to collapse
I've tried to install many different stock packages with pretty much the same results. Also, an image of my current settings attached. Is it a problem that I have 5.0.2 but MDL modem? Do I need to wipe everything before I run ODIN?
The only way that I can restore the phone is to ODIN install the recovery image shown below, then reinstall the CM12 ROM from the SD. When I try to install other zip packages through recovery/SD, they always fail. When I try to install other packages through ODIN, they always fail.
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.08.9-jfltespr.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)

laserman2431 said:
I've tried to install many different stock packages with pretty much the same results. Also, an image of my current settings attached. Is it a problem that I have 5.0.2 but MDL modem? Do I need to wipe everything before I run ODIN?
The only way that I can restore the phone is to ODIN install the recovery image shown below, then reinstall the CM12 ROM from the SD. When I try to install other zip packages through recovery/SD, they always fail. When I try to install other packages through ODIN, they always fail.
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_6.08.9-jfltespr.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
Since you installed Lollipop you need to wipe the internal sd. Also the stock images are here on XDA and have a much better download speed. Just look for Odin or TAR in the title. I recommend NG2. That's the latest one.

Solved.
Well. This is embarrassing. It turns out the problem was either with my USB port or my drivers. I had installed drivers and tried the other port already. Maybe it was just a bad combination.
I hope this might be helpful to other people having the same problem.
Thanks for the help!

laserman2431 said:
Well. This is embarrassing. It turns out the problem was either with my USB port or my drivers. I had installed drivers and tried the other port already. Maybe it was just a bad combination.
I hope this might be helpful to other people having the same problem.
Thanks for the help!
Click to expand...
Click to collapse
it's actually the most common problem with Odin.

Hi guy's i have a sprint s4 . While I was using custom rom it deleted my imei and now it show 00000000 how do I write it
---------- Post added at 02:54 AM ---------- Previous post was at 02:54 AM ----------
Need help
---------- Post added at 02:55 AM ---------- Previous post was at 02:54 AM ----------
I was trying to root phone and install custom rom

jaybhatia999 said:
Hi guy's i have a sprint s4 . While I was using custom rom it deleted my imei and now it show 00000000 how do I write it
---------- Post added at 02:54 AM ---------- Previous post was at 02:54 AM ----------
Need help
---------- Post added at 02:55 AM ---------- Previous post was at 02:54 AM ----------
I was trying to root phone and install custom rom
Click to expand...
Click to collapse
Just Odin stock ROM. That is the easiest way to get out back. This will restore you're phone to the state in which you received it.

But it will lock my phone back to sprint.. It's unlocked now

jaybhatia999 said:
But it will lock my phone back to sprint.. It's unlocked now
Click to expand...
Click to collapse
Sorry, I have no experience with that. But you definitely should have started with that bit of information.

Buongiorno sperando che qualcuno qui parli italiano volevo delle informazioni nel mio asus trasformers pad tf700t è stata cambiata la rom e vorrei portarla come era in origine per poi resettare il tablet

jaybhatia999 said:
But it will lock my phone back to sprint.. It's unlocked now
Click to expand...
Click to collapse
When did you install a ROM stock to an unlocked phone, the phone keeps it
I did the upgrade, MDC NG2 and kep it

Related

[Q] Hard to unbrick

Hey guys...
I need a little help from professionnals...I wanted to try a Cyanogen rom, the 10.1.3, a stable one, on my S4. So I downloaded it, I rooted my phone with cf-autoroot with Odin, intalled CWM Recovery. Then I did all the wipes and flashed the cyanogenmod.
Guess what, it didn't work The flash worked well but next infinite bootloop on the boot animation of cyanogen...So I tryied to go back to recovery, mount USB and flash an another rom of cyanogen. And the results was worse, the flash did'nt work at all, if I remember "failed to mount /system" or something similar. And when I tried to restard the phone, nothing happened.
So I wanted to go back to the stock rom to repair this mess. => Download mode then under PDA, my tar.md5 files. Didn't work. I also tried with a PIT file, same result.
I changed my usb cable, the version of Odin, the usb port.
Here's what Odin give :
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
I don't know what to do, I tried a lot of things beside all of this. Any ideas ?
THX
Try install STOCK ROM with older ODIN (click here), no the newest version
What stock rom are you trying to flash?
Thanks, but no change...
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUBMGA_I9505OXXBMG3_I9505XXUBMGA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Lennyz1988 said:
What stock rom are you trying to flash?
Click to expand...
Click to collapse
This is I9505XXUBMGA_I9505OXXBMG3_I9505XXUBMGA_HOME, official for Europe, 4.3
BeamGG said:
This is I9505XXUBMGA_I9505OXXBMG3_I9505XXUBMGA_HOME, official for Europe, 4.3
Click to expand...
Click to collapse
if you have the secured bootloader (knox warranty void 0x0 in download mode) that means you can not flash old firmware such as MGA. you can flash firmwares MH?, MI? or MJ?.
I9505XXUBMGA = 4.2.2.
Thats probably why the flashing fails.
Lennyz1988 said:
I9505XXUBMGA = 4.2.2.
Thats probably why the flashing fails.
Click to expand...
Click to collapse
I'm such an idiot...I hasd chosen the wrong file...I'm trying with the MJ5 now, I'll let you know
EDIT : Indeed it goes further, but not at the end :
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMJ5_I9505OXAEMJ5_I9505XXUEMJ5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
EDIT : I changed the usb port and re-installed the drivers, worked...finally, thx guys !
BeamGG said:
I'm such an idiot...I hasd chosen the wrong file...I'm trying with the MJ5 now, I'll let you know
EDIT : Indeed it goes further, but not at the end :
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMJ5_I9505OXAEMJ5_I9505XXUEMJ5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
EDIT : I changed the usb port and re-installed the drivers, worked...finally, thx guys !
Click to expand...
Click to collapse
Only changing usb port and reinstalling solved it?
I have the same issue with ODIN3 3.07.
need4steer said:
Only changing usb port and reinstalling solved it?
I have the same issue with ODIN3 3.07.
Click to expand...
Click to collapse
Hey man,
Sorry for this late answer. Yes, as I said, I only changed the usb port et reinstalling drivers...did it work for you ?
BeamGG said:
Hey man,
Sorry for this late answer. Yes, as I said, I only changed the usb port et reinstalling drivers...did it work for you ?
Click to expand...
Click to collapse
Unfortunately no. Apparently the tar.md5 file I was trying to flash was the problem. The developer released a newer version of it which was flashed okay. Thanks a lot anyway!
need4steer said:
Unfortunately no. Apparently the tar.md5 file I was trying to flash was the problem. The developer released a newer version of it which was flashed okay. Thanks a lot anyway!
Click to expand...
Click to collapse
Cool, you are welcome ! :good:

Problem while attempting to room Galaxy S4 I337 ATT

Phone: Galaxy S4 I337 AT&T with latest update, 4.4.3
What I did before I began the process:
1) Enable debugging mode on the phone
2) Installed latest Samsung Drivers
3) Used original USB Samsung cable
What I did: Download and ran Root and Recovery for ATT-TMO GS4-CASUAL-R527b and in doing so, processed failed.
Here is what looks like now:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Following step, to correct the problem, was I download the firmware that came with the phone, I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar. Zip file in size of 1.59GB and I used different version of Odin, including 1.85, 3.04, 3.05 and 3.07 with no success to fix the problem I caused in the first place.
This is what phone looks like -
This is what Odin looks like when it attempted to process the file above, I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUAMDL_I337ATTAMDL_I337UCUAMDL_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I would like to get my phone back running again. Can someone please guide me, if it possible to get it back to stock firmware. Please understand that I searched the forum and Google for all possible solutions, as well as YouTube videos. I am clearly not experience in rooting phone and this was my first attempt.
Thank you for all the help.
Remember that the phone has a locked boot loader which prevents stock recovery and kernel from being replaced. Also, the boot loader itself cannot be downgraded.
You were on KitKat which means you had firmware ending with NB1 or NC1. Trying g to flash the MDL files was trying to downgrade boot loader and hence the issue.
http://forum.xda-developers.com/showthread.php?t=2616221
Read the return to stock section of the above thread. Download and flash the NB1 firmware. There are 2 versions of which you can use either.
Method to update to latest NC1 is also given in the thread.
The only working recovery we have is safestrap. All custom ROM flashing happens with this.
Almost..but failed.
So I checked out the post you replayed and I did the following -
1) Downloaded I337UCUFNB1_4.4_Stock_Odin_tar from here
2) Used Odin v3.9.3 and here is the following result:
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUFNB1_TWRootable_Full_Odin.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> persdata.img.ext4
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
File tar.md5 comes very close to completing and stop; and I get a FAIL!
On the phone I get the following:
START [224, 1440]
BAR [240, 1440]
selchi said:
So I checked out the post you replayed and I did the following -
1) Downloaded I337UCUFNB1_4.4_Stock_Odin_tar from here
2) Used Odin v3.9.3 and here is the following result:
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I337UCUFNB1_TWRootable_Full_Odin.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> persdata.img.ext4
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
File tar.md5 comes very close to completing and stop; and I get a FAIL!
On the phone I get the following:
START [224, 1440]
BAR [240, 1440]
Click to expand...
Click to collapse
just keep trying, that happens from time to time...its usually a faultt usb port or cord, so try differnt ports or buy a new cord, ome time I was stuck with a bad cord and literally kept trying for 2-3 hours before it finally completed the odin flash
Sent from my SAMSUNG-SGH-I337 using Tapatalk

Need help tab 4 10.1 lte

Hello everyone, I'm new to this tablet and I need help. Sorry for my English
I tried putting a rom with odin and fails at the end of the installation.
My tablet is t-535
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
the text in odin 3.09:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T535XXU1ANH6_T535PHE1ANH1_T535XXU1ANH6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> FAIL! (Size)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
The solution is the pit, please give me
feuer1793 said:
Hello everyone, I'm new to this tablet and I need help. Sorry for my English
I tried putting a rom with odin and fails at the end of the installation.
My tablet is t-535
View attachment 3003086
View attachment 3003087
the text in odin 3.09:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T535XXU1ANH6_T535PHE1ANH1_T535XXU1ANH6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> FAIL! (Size)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
The solution is the pit, please give me
Click to expand...
Click to collapse
Why a pit? I think the pit is still on the tablet but that you arez trying to flash a wrong/corrupted rom.
EDIT: you are flashing a wrong ROM. Probably because of carrier branding. Don't start playing with .pit. You will end up hard bricked after 1 little mistake!!!
Droidphilev said:
Why a pit? I think the pit is still on the tablet but that you arez trying to flash a wrong/corrupted rom.
EDIT: you are flashing a wrong ROM. Probably because of carrier branding. Don't start playing with .pit. You will end up hard bricked after 1 little mistake!!!
Click to expand...
Click to collapse
I download of sammobile 3 roms of spain, england and greece and not worked
http://forum.xda-developers.com/tab-4/general/guide-how-to-pit-file-qualcomm-device-t2932088

Errors With Odin

I am trying to flash a stock rom on my Note 4 Exynos Version, with odin I have tried the latest version as well as some older ones. I have tried flashing both kit kat & lollipop but always get the same error. I have usb debugging ticked.
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> sboot.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
why is this happening?
Ta
Any help guys?
@home said:
Any help guys?
Click to expand...
Click to collapse
you are facing a locked bootloader as we all are (both exy and snap) the only solution to fix your bootloop is to install apps like phone info then find out what your phone PDA version is then find the exact PDA from Sammobile or if you you are Having an 910C flash latest COJ5 rom or if you are on 910H try installing COJ4 rom (just download and install the latest frimware from sammobile or ... and you will be just fine )
ArmanFGT said:
you are facing a locked bootloader as we all are (both exy and snap) the only solution to fix your bootloop is to install apps like phone info then find out what your phone PDA version is then find the exact PDA from Sammobile or if you you are Having an 910C flash latest COJ5 rom or if you are on 910H try installing COJ4 rom (just download and install the latest frimware from sammobile or ... and you will be just fine )
Click to expand...
Click to collapse
I followed your instructions and this is what I'm getting. Now what I need to do further? Previously I was using Sixperience ROM.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> modem.bin
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
sirius_gamer said:
I followed your instructions and this is what I'm getting. Now what I need to do further? Previously I was using Sixperience ROM.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> modem.bin
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Click to expand...
Click to collapse
well , i dont really know what the XmitData_write is , as i havent seen it since my s4 (everything was fine) ..
i think wiping would solve the Prob...
or maybe USB cable or odin version (+drivers)
2. if nothing works around ... try using KIES emergency updating ... its always the sweety
odin3 v 3.12
i have same problem;
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
sdstc said:
odin3 v 3.12
i have same problem;
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
problem is using UN-OFFICIAL USB CABLE
use FACTORY CABLE FIXes problem
sdstc said:
problem is using UN-OFFICIAL USB CABLE
use FACTORY CABLE FIXes problem
Click to expand...
Click to collapse
@sdstc is right you can fix __XmitData_Write with changing the cable
i used an original sammy cable and it didnt work. than i used another sammy cable and then it just worked
my device was a Tab S btw no note 4 or s4
bu arada cok sagol sdstc kardes
TimurAlaskara_TR said:
@sdstc is right you can fix __XmitData_Write with changing the cable
i used an original sammy cable and it didnt work. than i used another sammy cable and then it just worked
my device was a Tab S btw no note 4 or s4
bu arada cok sagol sdstc kardes
Click to expand...
Click to collapse
i all the time face with that error and i forgot use original cable
(ne için teşekkür?)
sdstc said:
i all the time face with that error and i forgot use original cable
(ne için teşekkür?)
Click to expand...
Click to collapse
Sen olmasan telefon hala bozuktu cunku sjsjsj
help plz
sdstc said:
problem is using UN-OFFICIAL USB CABLE
use FACTORY CABLE FIXes problem
Click to expand...
Click to collapse
<OSM> Please wait..
<OSM> N910CXXS2DQG1_N910COXA2DPH1_N910CXXU1DPC1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Bricked SPH-L720 after modem firmware upgrade attempt. Help!

Phone: SPH-L720
Baseband: L720VPUAMDL
OS: PAC-ROM 5.1.1
Attempted to update the modem from MDL to OK3 with only the modem.bin and NON-HLOS.bin file via Odin 3.10.7. The upgrade failed. Now the phone fails to boot and displays the message "Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again". ODin was run "as administrator" and I have swapped cables and USB ports. The phone will go into download mode and display the follow screen:
PRODUCT NAME: SPH-L720
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: Custom
KNOX KEARNEL LOCK: 0xfffffffC
KNOX WARRANTY VOID: 0xFFFFFFFC
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enable
eMMC BURST MODE: enabled
I attempted to reload the factory image L720vpumdl and it failed with a missing PIT partition error. see below.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
I attempted again with the same image and added a L72016GB pit file.
With PIt file added:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
If anyone has any suggestion or a known solution I would apreciate it. I do have access to another SPH-L720 but it baseband is on NAE.
Thanks
leapcad said:
Phone: SPH-L720
Baseband: L720VPUAMDL
OS: PAC-ROM 5.1.1
Attempted to update the modem from MDL to OK3 with only the modem.bin and NON-HLOS.bin file via Odin 3.10.7. The upgrade failed. Now the phone fails to boot and displays the message "Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again". ODin was run "as administrator" and I have swapped cables and USB ports. The phone will go into download mode and display the follow screen:
PRODUCT NAME: SPH-L720
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: Custom
KNOX KEARNEL LOCK: 0xfffffffC
KNOX WARRANTY VOID: 0xFFFFFFFC
CSB-CONFIG-LSB: 0x30
WRITE PROTECTION: Enable
eMMC BURST MODE: enabled
I attempted to reload the factory image L720vpumdl and it failed with a missing PIT partition error. see below.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
I attempted again with the same image and added a L72016GB pit file.
With PIt file added:
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
If anyone has any suggestion or a known solution I would apreciate it. I do have access to another SPH-L720 but it baseband is on NAE.
Thanks
Click to expand...
Click to collapse
Try the full OK3 tar
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
bilgerryan said:
Try the full OK3 tar
Click to expand...
Click to collapse
Tried the full ok3 tar file ( L720VPUGOK3_L720SPTGOK3_L720VPUGOK3_HOME.tar.md5). It ran much longer but soon failed also. Posted results below.
The phone screen added 2 lines in red at the bottom. Start [224, 1440] Bar [224, 1440]
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
leapcad said:
Tried the full ok3 tar file ( L720VPUGOK3_L720SPTGOK3_L720VPUGOK3_HOME.tar.md5). It ran much longer but soon failed also. Posted results below.
The phone screen added 2 lines in red at the bottom. Start [224, 1440] Bar [224, 1440]
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> __XmitData_Write
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Click to expand...
Click to collapse
Can you get into Recovery and flash a ROM? If not, can you flash a recovery in Odin?
bilgerryan said:
Can you get into Recovery and flash a ROM? If not, can you flash a recovery in Odin?
Click to expand...
Click to collapse
The phone had TWRP 3.0.2 before the mishap but that would not load. I went back into Download mode and reloaded TWRP 2.8.4.0 via Odin and that was successful. When I attempted to boot the phone it went into (boot loop) and was stuck on the Samsung Galaxy S4 boot screen. I went back into recovery and did a factory wipe. TWRP complained at the very end it was unable to mount /system. I went into advanced wipe and selected system. The wipe/format of /system came back clean. I then did a nandroid restore and rebooted. We are finally up and running.! :good:
Thanks bilgerryan for your assistance.!!!
TWRP 2.8.4.0 load:
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
leapcad said:
The phone had TWRP 3.0.2 before the mishap but that would not load. I went back into Download mode and reloaded TWRP 2.8.4.0 via Odin and that was successful. When I attempted to boot the phone it went into (boot loop) and was stuck on the Samsung Galaxy S4 boot screen. I went back into recovery and did a factory wipe. TWRP complained at the very end it was unable to mount /system. I went into advanced wipe and selected system. The wipe/format of /system came back clean. I then did a nandroid restore and rebooted. We are finally up and running.! :good:
Thanks bilgerryan for your assistance.!!!
TWRP 2.8.4.0 load:
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
Cool, glad you got it back up and running.

Categories

Resources