SOFT BRICK - Fail flashing Stock ROM at hidden.img ODIN
Guys hello.
I have rooted and successfully flashed custom recovery and custom firmwares on my Note 3 (9005 Qualcomm LTE), however the last flash (stock ROM 4.4.2 N9005XXUENB4) attempt with Odin (v 3) failed at the end of the flash process ( hidden.img.ext4 -> FAIL! (ext4)):
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> cache.img.ext4
<ID:0/003> hidden.img.ext4
<ID:0/003> FAIL! (Ext4)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Now the phone wouldn't boot any more....
Than I try the pit file ........sorry the some situation......................................
Can somebody help or advise me?:crying::crying:
Cheers Shark001
This is possible coz the firmware you have installed (maybe you upgrade your bootloader flashing that custom roms) is newer that the one you are trying to flash.
Joku1981 said:
This is possible coz the firmware you have installed (maybe you upgrade your bootloader) is newer that the one you are trying to flash.
Click to expand...
Click to collapse
Thank you for your quick answer.......
I had this ROM [SM-N9005][XXUGNI4]_BoBCaTROM_EVO_v12 multi density........
Is there a way how I can solve it?
Shark001 said:
Thank you for your quick answer.......
I had this ROM [SM-N9005][XXUGNI4]_BoBCaTROM_EVO_v12 multi density........
Is there a way how I can solve it?
Click to expand...
Click to collapse
Ni4 is much newer....so flash a Ni4 room. ...
Shark001 said:
Thank you for your quick answer.......
I had this ROM [SM-N9005][XXUGNI4]_BoBCaTROM_EVO_v12 multi density........
Is there a way how I can solve it?
Click to expand...
Click to collapse
Are you using a branded device? Where is your device from? Do you know the CSC of your device?
Go to Sammobile.com and take a look the firmwares GNI4. Download and flash it. Done.
HI
My Phone was brandet by T-Mobile (Note3 is rooted) but I used a custom Rom the BobCat Rom and the reported Error happend during the tryed to reinstall the xxxGNI4 version from Sammobile.
Therefore I'm confused . Sorry I wrote the wrong version in my first post....
Shark001 said:
HI
My Phone was brandet by T-Mobile (Note3 is rooted) but I used a custom Rom the BobCat Rom and the reported Error happend during the tryed to reinstall the xxxGNI4 version from Sammobile.
Therefore I'm confused . Sorry I wrote the wrong version in my first post....
Click to expand...
Click to collapse
I found the CSC Version of the BObCatROm ............it is N9005AXXGNJ1
Cheers
Shark001 said:
I found the CSC Version of the BObCatROm ............it is N9005AXXGNJ1
Cheers
Click to expand...
Click to collapse
T-mobile of what country?
Related
I tried to flash a stock ROM and got an error in ODIN that said:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Now my phone only boots into Odin Mode and to a screen that says:
"Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
Please Help!
Odin stock Rom tar and start from scratch.
carwashman said:
Odin stock Rom tar and start from scratch.
Click to expand...
Click to collapse
I tried multiple Stock ROMs and I get the same error. Do you know of a legit one? The ones I had could've been corrupt.
What device do you have?
carwashman said:
What device do you have?
Click to expand...
Click to collapse
The Sprint Samsung Galaxy S4. SPH-L720
You may have to try the kitkat rom.
http://forum.xda-developers.com/showthread.php?t=2663619
This is the one I used recently. I was already on NAE
carwashman said:
http://forum.xda-developers.com/showthread.php?t=2663619
This is the one I used recently. I was already on NAE
Click to expand...
Click to collapse
Is there a way to find out what I'm on without being able to elsewhere except download?
EDIT: I get the same error with that ROM.
EDIT #2: I got it to work!!! Thanks so much guys!
good day ,
anyone can help me with installing stock version of android 4.3 version on my GS4 ?! i have problem while using odin v3.09 to flash my Galaxy s4 i9505 to stock firmware version 4.3 with the md5 file downloaded from sammobile.com , here is some info about my phone :
having CWM recovery installed
running on custom ROM CM11 4.4.4
error message in odin is as below :
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sbl1.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl2.mbn
<ID:0/005> sbl3.mbn
<ID:0/005> rpm.mbn
<ID:0/005> aboot.mbn
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
micphone7 said:
good day ,
anyone can help me with installing stock version of android 4.3 version on my GS4 ?! i have problem while using odin v3.09 to flash my Galaxy s4 i9505 to stock firmware version 4.3 with the md5 file downloaded from sammobile.com , here is some info about my phone :
having CWM recovery installed
running on custom ROM CM11 4.4.4
error message in odin is as below :
Odin v.3 engine (ID:5)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Firmware update start..
SingleDownload.
sbl1.mbn
NAND Write Start!!
sbl2.mbn
sbl3.mbn
rpm.mbn
aboot.mbn
FAIL! (Auth)
Complete(Write) operation failed.
All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Download the official firmware of your country and carrier from samobile.Com and flash with odin
This will flash stock firmware and stock recovery
Sent from my GT-I9505 using Tapatalk
1eyedmonster said:
Download the official firmware of your country and carrier from samobile.Com and flash with odin
This will flash stock firmware and stock recovery
Sent from my GT-I9505 using Tapatalk
Click to expand...
Click to collapse
I just bought it from thailand !
micphone7 said:
I just bought it from thailand !
Click to expand...
Click to collapse
You wont be able to flash 4.3 if youre on 4.4.2
"If someone helps, never forget to hit thanks ? "
Hello, I have tried updating my N9005 to the latest firmware 5.0 provided on Sammobile. After attempting to flash it via ODIN, the following error occurs:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
Retried this step several times, but i have received the same error.
Following a few instructions found on the XDA forums, I tried using PIT file in order to re-partition.
The phone now reboots but will not go past the first boot screen "Samsung Galaxy Note3 N9005".
I tried pulling out the battery and performing a factory reset (along with wiping caches), but the situation is still the same after rebooting the device.
Also I have noticed that upon accessing "recovery mode", a error stating " Failed to mount /system (Invalid argument)" error is displayed.
I'm pretty new at upgrading phones and I've bought this phone recently and was unaware of the consequences of flashing ROMS via Odin.
The initial fw. on the device was 4.4.2 Official Samsung. Is there any way that I can make the phone reboot normally with fw. 4.4.2? Or any other firmware for that matter?
Thanks in advance.
AndreiRonaldo said:
Thanks in advance.
Click to expand...
Click to collapse
Reflash the firmware again now via ODIN without the .pit file.
Joku1981 said:
Reflash the firmware again now via ODIN without the .pit file.
Click to expand...
Click to collapse
I've tried that several times without success. But the issue was fixed. Apparently the PIT file I was using did not match the ROM i was flashing. I just had to find a matching pair of both ROM and PIT and now I've successfully booted my device. Hope that this thread might help others in need for answers to similar questions.
Alright, this is taking alot more than i had expected, after finally managing to boot my device, I've noticed that flashed rom behaves awfully, my phone is stuttering, and i have no sound. Also, my IMEI is displayed as "Unknown" in the "Status'" section of the device's Settings. Any suggestion on how to fix this issue?
flash the stock the rom you have before
I have an Australian SM-N9005 that I want to upgrade to lollipop. I have done this a few other times without incidence on other Samsung phones but this one won't do it. There isn't any Australian 5.0 firmwares so I have tried the Taiwan and Hong Kong firmwares from SamMobile but I get this message every time
"<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> cache.img.ext4
<ID:0/003> FAIL! (Ext4)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)"
Can someone please help out with this, appreciated
have you the same problem by installing a custom rom?
belveder69 said:
I have an Australian SM-N9005 that I want to upgrade to lollipop. I have done this a few other times without incidence on other Samsung phones but this one won't do it. There isn't any Australian 5.0 firmwares so I have tried the Taiwan and Hong Kong firmwares from SamMobile but I get this message every time
"<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> sdi.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> cache.img.ext4
<ID:0/003> FAIL! (Ext4)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)"
Can someone please help out with this, appreciated
Click to expand...
Click to collapse
DONT TRY other countreys rom special assian...you will lose your imei.lolipop is not that good and everybody runs from it
If you have root acces you can try darklord s6 v3 is the best lolipop for note 3 n9005(you will void your warranty knox 0x1).
The rom is ported from s6 edge and is verry stable
Sent from my SM-A800F using XDA Free mobile app
I worked it out thanks, found the England firmware furthware further down the page.
Yes i could install custom roms but had no sounds and a few other buggy issues.
I disagree about not using foreign firmwares, i use Indian firmware on my Note 4, works just fine
belveder69 said:
I worked it out thanks, found the England firmware furthware further down the page.
Yes i could install custom roms but had no sounds and a few other buggy issues.
I disagree about not using foreign firmwares, i use Indian firmware on my Note 4, works just fine
Click to expand...
Click to collapse
Glade it works ... the ideea was that assian softwares are different for rest..the dark lord rom has no problems with sound ...give it a try.i have it and i dont have any problems
Cheers
Sent from my SM-A800F using XDA Free mobile app
Hello everyone,
I bricked my phone…. It is a SM-J510FN and when I start it right now, it shows "An error has occured while updating the decive Software. etc." Smart Switch is not recognizing the decive anymore, I cannot enter TRWP and I tried to Flash the stock Rom with Odin but it fails with the following error :
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 2878 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> hyp.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I would highly appreciate any help since I am running out of ideas what to do....
Thanks in Advance!
ottavio22 said:
Hello everyone,
I bricked my phone…. It is a SM-J510FN and when I start it right now, it shows "An error has occured while updating the decive Software. etc." Smart Switch is not recognizing the decive anymore, I cannot enter TRWP and I tried to Flash the stock Rom with Odin but it fails with the following error :
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 2878 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> hyp.mbn
<ID:0/003> NON-HLOS.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I would highly appreciate any help since I am running out of ideas what to do....
Thanks in Advance!
Click to expand...
Click to collapse
Did you try flashing TWRP again? Bc you flash stock one! If you could enter twrp, flash some of ROMs for your device.
RootingPro-18 said:
Did you try flashing TWRP again? Bc you flash stock one! If you could enter twrp, flash some of ROMs for your device.
Click to expand...
Click to collapse
Thank you for your answer. I did try that but was unable to to boot into TWRP. I finally managed to Flash the stock ROM via Odin. The mistake I pointed out above was fixed by changing from a 3.0 USB to a 2.0 USB port. Weirdly Odin seems to create Errors when using 2.0 in some rare Occasion. For everyone encoutering the same I encourage you to check if you are using a 2.0 USB.
Thank you for the answer anyway. Thread can be closed.
ottavio22 said:
Thank you for your answer. I did try that but was unable to to boot into TWRP. I finally managed to Flash the stock ROM via Odin. The mistake I pointed out above was fixed by changing from a 3.0 USB to a 2.0 USB port. Weirdly Odin seems to create Errors when using 2.0 in some rare Occasion. For everyone encoutering the same I encourage you to check if you are using a 2.0 USB.
Thank you for the answer anyway. Thread can be closed.
Click to expand...
Click to collapse
i had no issues with 3.0