Related
NOTE : this is not my own procedure but i just wanna share this with you guys since some tab users here are having problems restocking their tab to gingerbread, i have also added some notes and troubleshooting in case there will be an issue flashing the rom
link to the original post credits of course to the writer > how to restock p1000 to gingerbread 2.3
btw, this is a complete and full tutorial/step-by-step guide on how to restock gingerbread rom, so if you did not download all requirements, restocking wont be successful
my story and experience : hey guys, yesterday night, i softbricked my galaxy tab p1000 which was running cm9, it turned out like that when i went to recovery and wipe all data, cache, dalvik, even system, and boot. i tried reflashing the cm9.zip but as it was installing its update, my tab suddenly boot into battery icon, meaning it was already empty (maybe, dont have any idea), then, since it was already 12 midnight, there were no internet cafes open in our village, so i went out though somehow it might be dangerous for me, then, i found an internet cafe open. i rent a pc, first, i tried to go to download mode, so some drivers will be installed, but it kept showing "unkown device recognized" bla bla.. still.. i didnt lose hope. so i searched on google, and i found this site > http://suzhipackz.blogspot.com/2012/07/how-to-re-stock-samsung-galaxy-tab.html , when i finished downloading odin, i opened it to check whether it will read my device or not, first three attempts, it did not. so, i thought of downloading samsung kies so the drivers will be installed (safest way really to install samsung drivers), then i still looked for a smaller file (while waiting for kies to complete its download), then i found that there is a smaller zip file for you to install samsung drivers (see attachment below), i installed it, but still odin cant detect my device (try it, might be just on the pc i rented), so i just waited for kies to complete.. after a couple of minutes, successfully downloaded kies, and installed it. i tried connecting tab to pc with odin opened, i rebooted to download mode again and reconnect tab to pc, and voila! odin read my device! so, since pc has already detected my device, i just waited about 1 1/2 hours for the rom and the pit file and the db data file.... after almost 2 and half hours of crossing fingers, i have revived my tab and restocked it to gingebread 2.3!
HOW TO RESTOCK SAMSUNG GALAXY TAB p1000 to 2.3.3 GINGER BREAD STOCK ROM?
HERE:
- ALL REQUIREMENTS
.......Samsung KIES > LINK FOR SAMSUNG KIES
.......ODIN3 v1.7 > LINK FOR ODIN3 v1.7
.......p1000xxjq1_p1000xxjq1_p1000xxjpz < THIS IS STOCK ROM > LINK FOR STOCK ROM
.......gt-p1000_mr_PIT > LINK FOR PIT
.......dbdata.zip > LINK FOR DBDATA
.......place it all in ONE FOLDER in desktop "unzip it all"
PLEASE DOWNLOAD ALL OF THIS BEFORE YOU CONTINUE..............
PROCEDURE:
.......Turn off tab
.......open ODIN3 v1.7
.......click on the PDA and select - p1000xxjq1_p1000xxjq1_p1000xxjpz in your computer
.......clink on the PIT and select - gt-p1000_mr_PIT
.......Check only RE-PARTITION, "uncheck auto reboot and f.reset time"
.......in your tab press and hold "VOLUME DOWN AND POWER BUTTON"
.......if DOWNLOADING APPEAR leave it like that
.......now, connect you tab in computer
.......if ODIN detects your phone PRESS START in ODIN
.......wait for it until success, after that disconnect your tab
(if for an instance it stuck on downloading mode but you have already finished flashing, do not worry, you just have to manually hold the power button for it to boot up, it might get into recovery, so please reboot the system (it might also be a touch recovery so please tab the home touch key to continue) then if it keeps on booting on "samsung", do not worry, you are not done yet with the restocking procedure, so please proceed to the next step)
.......press and hold power button until it will turn off
.......open ODIN3 v1.7 again
.......UNCHECK it all "re-partition, auto reboot, f.reset time"
.......click on the PDA and select dbdata.zip
.......press and hold "VOLUME DOWN AND POWER BUTTON" again
.......if DOWNLOADING APPEAR leave it like that
.......now, connect your tab again
.......if ODIN detects your phone PRESS START in ODIN
.......wait for it until success, after that disconnect your tab
(again, if it is stuck on downloading mode but you have successfully done the flashing, hold power key to turn the tab on, and if it keeps on booting to "samsung" again, do the next step)
.......This time we will go to CLOCKWORKMOD by holding "VOLUME UP and POWER BUTTON"
(then wipe data, and wipe cache, (volume keys to scroll up or down, and home touch key to select) and reboot system, wait for a minute or two and home screen will now appear)
.........................................NOW YOUR IN STOCK ROM AGAIN 2.3.3 GINGER BREAD
another note : when there is an error for example that flashed on your tab screen like a color red "E:\ " something like that, do not worry, it is the external sd card (i dont have one so it was an error then but not a problem, no worries) just let it be, wait until it finishes
some files are already attached below coz they are just small in size
clicking "thanks" button is enough for me..
just sharing this with you guys...
happy restocking!! :laugh:
Update Prob
mastersymvts said:
I want get full file samsung tab p1000. For flash my tab.. Tq
Click to expand...
Click to collapse
Hi Guys is crashed my tab.
i get it functional with the stock rom 2.3.6
P1000XXJPZ
Kernel 2.6.35.7
[email protected]#2
Build gingerbread.XWJQ8
i wantetd to Flash to a newer rom but noting worked any ideas?
I modified a couple years ago the tab to include the sd space as System space. I do Not rember how i did this....?
If i get throught the stock partion all would be find but i couldn´t.
Regular mod Installation doesnt work, rooting also isn´t possible ...
readin with Heimdall shows this message
Initialising connection...
Detecting device...
ERROR: Failed to access device. libusb error: -12
I hope you guys have any ideas.
Greets
P1000XXJQ1_P1000XXJQ1_P1000XXJPZ.zip do you stil have this?
Hotfile is down
Stock Rom's Link doesn't work
So, I tried your recipe and it worked pretty well for me, but the annoying thing about it was the links to the Stock Rom, so i got the below link as a mirror for those who are interested.
p1000xxjq1_p1000xxjq1_p1000xxjpz < THIS IS STOCK ROM >h-t-t-p-:-/-/-f-i-l-e-s-c-r-o-p-t-u-b-e-.-c-o-m/file/7806957-p1000xxjq1-rar
Couldn't find the given URL
LeMasoud said:
So, I tried your recipe and it worked pretty well for me, but the annoying thing about it was the links to the Stock Rom, so i got the below link as a mirror for those who are interested.
p1000xxjq1_p1000xxjq1_p1000xxjpz < THIS IS STOCK ROM >h-t-t-p-:-/-/-f-i-l-e-s-c-r-o-p-t-u-b-e-.-c-o-m/file/7806957-p1000xxjq1-rar
Click to expand...
Click to collapse
I couldn't locate the file.
need new links. prefer putlocker/mediafire etc.
THKS a Lot!!!!
Great!! many thanks my p1000 have a second life
http://www.4shared.com/get/B-DeOju6/P1000XXJQ1.html here you go its a miracle what using google could do using the right search methods if you would thanks i would really apreciete it guys and gals.
I just flashed my tab stock 2.3.6 from cm11 using odin. But stuck in bootloop. After going to recovery i get error message (red) as in pic. Where did i go wrong?
Thank you for this and sorry for reviving an old thread. It sucks when links go dead (or offer that sketchy ilivid crap). Here is a mirror:
Mirror for samsung galaxy tab P1000 stock odin TAR: stock-P1000XXJQ1_P1000XXJQ1_P1000XXJPZ_HOME.tar
https://mega.co.nz/#!7wohlbKT!i3K7lvIfombRdJEzUUP-fiIZQS1qeStOr16tty-T86w
And a mirror to download ODIN 3 v 1.85: odin3-v1.85.zip
https://mega.co.nz/#!W553iL7B!vZTVktUwwg35a_glWGgBEaIDg11JVgkvFZ94mpzECas
2.3...
I think that there was a couple of kernel and Android security flaws in Linux 2.6, not fixed by Samsung Electronics Co. Ltd..
Samsung Tab P1000 stuck in nowhere!
First of all thanks the OP for the brilliant post on how to re-stock GB on P1000.
Earlier today I was fooling around with my P1000 to update it from CM11 to Omnirom 5.0.2, troubles started there. I was trying to install the TWRP recovery over CWM, and that is when all hell broke loose.
1. P1000 couldn't mount my internal SD. The tab was perfectly booting to a previous version of JB CM sapir, which I don't have any clue appeared where from. The storage showed the 2 GB internal memory, but the 12GB internal SD was missing out.
And the CWM errors were E:/can't mound internal SD
2. Now, after wiping data, dalvik, battery stats, formatting and all that, the tab doesn't even boot into the OS. The moment the power button is on, CWM initiates a count down saying, trying to mount SD, but unable to do so. After 20 seconds, the tab starts this whole process again, and thus a loop.
3. I tried to re-stock to GB; but my tab isn't being detected by Odin in download mode. Odin detects the tab when it is turned on and when the tab is on countdown-restart-countdown loop; but not in download mode.
I am a total noob, and I don't want to throw my tab away as I am a student and can't afford to get a new one Someone please help me to fix the issue. Thanks in advance!
PolaritySwitch said:
First of all thanks the OP for the brilliant post on how to re-stock GB on P1000.
Earlier today I was fooling around with my P1000 to update it from CM11 to Omnirom 5.0.2, troubles started there. I was trying to install the TWRP recovery over CWM, and that is when all hell broke loose.
1. P1000 couldn't mount my internal SD. The tab was perfectly booting to a previous version of JB CM sapir, which I don't have any clue appeared where from. The storage showed the 2 GB internal memory, but the 12GB internal SD was missing out.
And the CWM errors were E:/can't mound internal SD
2. Now, after wiping data, dalvik, battery stats, formatting and all that, the tab doesn't even boot into the OS. The moment the power button is on, CWM initiates a count down saying, trying to mount SD, but unable to do so. After 20 seconds, the tab starts this whole process again, and thus a loop.
3. I tried to re-stock to GB; but my tab isn't being detected by Odin in download mode. Odin detects the tab when it is turned on and when the tab is on countdown-restart-countdown loop; but not in download mode.
I am a total noob, and I don't want to throw my tab away as I am a student and can't afford to get a new one Someone please help me to fix the issue. Thanks in advance!
Click to expand...
Click to collapse
Can you flash at least the PIT in countdown mode(after you flashed the PIT, it goes to download mode)
Flash during countdown...
black_blob said:
Can you flash at least the PIT in countdown mode(after you flashed the PIT, it goes to download mode)
Click to expand...
Click to collapse
Thank you! I tried doing that. On the success/failure counter on Odin, it shows as a failure
PolaritySwitch said:
Thank you! I tried doing that. On the success/failure counter on Odin, it shows as a failure
Click to expand...
Click to collapse
Can you try booting the Vol- or the Vol+ button until you see the flashscreen?
Weird.(and making the tablet unbrickable needs a mod which I hope that you don't do)
black_blob said:
Can you flash at least the PIT in countdown mode(after you flashed the PIT, it goes to download mode)
Click to expand...
Click to collapse
black_blob said:
Can you try booting the Vol- or the Vol+ button until you see the flashscreen?
Weird.(and making the tablet unbrickable needs a mod which I hope that you don't do)
Click to expand...
Click to collapse
Well yes, Vol+ takes me to CWM recovery and Vol- takes me to download mode. Odin detects my Tab on CWM; I tried flashing the PIT which resulted in a failure. And on the download mode as I mentioned earlier, Odin doesn't detect my Tab
Well, I am all ears about the mod you're mentioning about, but let's just hope for now that I don't need that
PolaritySwitch said:
Well yes, Vol+ takes me to CWM recovery and Vol- takes me to download mode. Odin detects my Tab on CWM; I tried flashing the PIT which resulted in a failure. And on the download mode as I mentioned earlier, Odin doesn't detect my Tab
Well, I am all ears about the mod you're mentioning about, but let's just hope for now that I don't need that
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1312391
very Helpful
you Saved my life ... thank you veeeeeeeery much
Thanks for sharing this method. I quiet had a problem with the drivers and the link for them isn't available but I got a way to fix it. Thanks anyways.
Can you guys help me out with my p1000 tab too its bootlooped its in a stock recover and unrooted . I tried wiping data but nothing happens
thank you soo much
Hey guys.
I have been doing a lot of researches before creating this new thread.
Here is my problem with a Samsung Galaxy s3 I9300T (Australia - Vodafone build). I was given the phone, since it was stuck in a boot loop after a software update issue with Kies (I think from memory 4.2 or something).
The phone boots up, displays the Vodafone logo, and is stuck on the Samsung logo. The phone doesn't restart but stays idle there.
It is impossible to reach the download mode with the use of the 3 buttons, but a USB JIB I bought on ebay does the trick.
Odin recognizes the phone, I can flash a stock Kernel from Samsmobile or root/install the CWM.
BUT, there is no way (so far?) to reach the recovery mode.
I tried to flash a new boot loader, tried to check any physical issue with the buttons, but nothing seems wrong.
I have been looking for tools such a android toolbox/toolkit etc, in the hope one would be able to wipe/flash the nand or even unbrick or whatsoever, from a download mode and not ADB, since I there no fast boot available.
I am ready to try anything, since there's nothing to loose here.
I'm running windows 7 from Parallel desktop.
Thanks mates.
Anthony
tonythrash69 said:
Hey guys.
I have been doing a lot of researches before creating this new thread.
Here is my problem with a Samsung Galaxy s3 I9300T (Australia - Vodafone build). I was given the phone, since it was stuck in a boot loop after a software update issue with Kies (I think from memory 4.2 or something).
The phone boots up, displays the Vodafone logo, and is stuck on the Samsung logo. The phone doesn't restart but stays idle there.
It is impossible to reach the download mode with the use of the 3 buttons, but a USB JIB I bought on ebay does the trick.
Odin recognizes the phone, I can flash a stock Kernel from Samsmobile or root/install the CWM.
BUT, there is no way (so far?) to reach the recovery mode.
I tried to flash a new boot loader, tried to check any physical issue with the buttons, but nothing seems wrong.
I have been looking for tools such a android toolbox/toolkit etc, in the hope one would be able to wipe/flash the nand or even unbrick or whatsoever, from a download mode and not ADB, since I there no fast boot available.
I am ready to try anything, since there's nothing to loose here.
I'm running windows 7 from Parallel desktop.
Thanks mates.
Anthony
Click to expand...
Click to collapse
after flashing newfirmware using download mode+odin the phone cant reboot?have you tried diff version firmware from sammobile .
nainaabd said:
after flashing newfirmware using download mode+odin the phone cant reboot?have you tried diff version firmware from sammobile .
Click to expand...
Click to collapse
I tried 2 different firmware from SAMSmobile, after flashing in Odin, nothing changes. The phone reboots (if the case is ticked) and stays stuck on the samsung logo, after the vodafone splash screen.
tonythrash69 said:
I tried 2 different firmware from SAMSmobile, after flashing in Odin, nothing changes. The phone reboots (if the case is ticked) and stays stuck on the samsung logo, after the vodafone splash screen.
Click to expand...
Click to collapse
maybe something went wrong in partition table during kies upgrade, do you tried a full system reinstall comprensive of pit image?
myabe this get phone back to life but i think you will lose efs.
Well normaly after flashing your right Firmware you should be able to acces recovery...
franco853 said:
maybe something went wrong in partition table during kies upgrade, do you tried a full system reinstall comprensive of pit image?
myabe this get phone back to life but i think you will lose efs.
Click to expand...
Click to collapse
How can I perform what you call a "full system reinstall comprehensive of PIT image"?
I have stock firmware, but no PIT file or CSC or whatsoever.
what do you mean by losing EFS? (encryption ??)
Any help is much appreciated.
tonythrash69 said:
How can I perform what you call a "full system reinstall comprehensive of PIT image"?
I have stock firmware, but no PIT file or CSC or whatsoever.
what do you mean by losing EFS? (encryption ??)
Any help is much appreciated.
Click to expand...
Click to collapse
efs is a system partition wich contains your phone's hardware serial numbers, such as imei, wi-fi mac ecc... losing this means you can't connect to phone network until you restore it(i'm not sure you lose it)
i found this guide here on the forum to restore from brick's or similiar, i think you can try this if normal flashing don't work:
http://forum.xda-developers.com/galaxy-s3/help/solved-pit-bricked-dead-problem-gt-t2535367
When you flash full firmware from Samsung (.tar.md5), it includes things such as bootloader, tz, modem, system, cache, preload and the recovery. Just make sure to download it from site such as sammobile, and you can check yourself if your .tar.md5 you're about to flash includes these things using i.e. 7zip.
Untick "auto reboot" option and flash it. After it's done, it won't auto reboot but Odin will change text to "RESET!", this is a signal for you that it's finished.
Hold on Vol-Up+Home+Power for about 7 seconds, until you see Samsung Galaxy S3 logo. It MUST enter stock recovery you've just flashed, unless your hardware is broken. From there you can select Wipe data / factory reset.
Good luck.
JustArchi said:
When you flash full firmware from Samsung (.tar.md5), it includes things such as bootloader, tz, modem, system, cache, preload and the recovery. Just make sure to download it from site such as sammobile, and you can check yourself if your .tar.md5 you're about to flash includes these things using i.e. 7zip.
Untick "auto reboot" option and flash it. After it's done, it won't auto reboot but Odin will change text to "RESET!", this is a signal for you that it's finished.
Hold on Vol-Up+Home+Power for about 7 seconds, until you see Samsung Galaxy S3 logo. It MUST enter stock recovery you've just flashed, unless your hardware is broken. From there you can select Wipe data / factory reset.
Good luck.
Click to expand...
Click to collapse
Yes this is what I did.
But after "RESET" doing it, holding the buttons won't let me reach the recovery.
Is there a way to access it ? like for instance a USB JIG allowed me to access the DOWNLOAD mode; whereas holding the buttons never let me.
tonythrash69 said:
Yes this is what I did.
But after "RESET" doing it, holding the buttons won't let me reach the recovery.
Is there a way to access it ? like for instance a USB JIG allowed me to access the DOWNLOAD mode; whereas holding the buttons never let me.
Click to expand...
Click to collapse
I don't think so. Probably your buttons are broken then.
JustArchi said:
I don't think so. Probably your buttons are broken then.
Click to expand...
Click to collapse
I still do not understand that NO software is able to address the phone, like the recovery mode does.
We can flash from a computer, how come not to wipe from a computer.
assuming that someone has no screen or broken buttons, i'm sure there's a way to access wipe and/or access the recovery to flash a stock rom.
Thanks
tonythrash69 said:
I still do not understand that NO software is able to address the phone, like the recovery mode does.
We can flash from a computer, how come not to wipe from a computer.
assuming that someone has no screen or broken buttons, i'm sure there's a way to access wipe and/or access the recovery to flash a stock rom.
Thanks
Click to expand...
Click to collapse
do you tried the guide i linked some post ago? the one with the repartition file?
franco853 said:
do you tried the guide i linked some post ago? the one with the repartition file?
Click to expand...
Click to collapse
Hey, yes I tried the link, but again I cannot access the recovery to flash the .zip file.
When I hold the buttons as soon as the logo "galaxy s III GTI9300" appears, the screen goes black and the logo comes back again.
If I release one button, the vodafone splash screen appears, and the boot is stuck on the samsung logo.
I assume, the buttons are working because of what I just explained.
But again, I cannot access the recovery.
Last week, for some reason, after flashing I has a "setup wizard" from appeared, and crashed. that was the only time. I could see the lights under the touch buttons coming on. After the crash, I tried to reinstall and couldn't do it.
I am still sure there should be a way to wipe the nand completely or install from the SD card via the download mode.
Any help is welcome
tonythrash69 said:
Hey, yes I tried the link, but again I cannot access the recovery to flash the .zip file.
When I hold the buttons as soon as the logo "galaxy s III GTI9300" appears, the screen goes black and the logo comes back again.
If I release one button, the vodafone splash screen appears, and the boot is stuck on the samsung logo.
I assume, the buttons are working because of what I just explained.
But again, I cannot access the recovery.
Last week, for some reason, after flashing I has a "setup wizard" from appeared, and crashed. that was the only time. I could see the lights under the touch buttons coming on. After the crash, I tried to reinstall and couldn't do it.
I am still sure there should be a way to wipe the nand completely or install from the SD card via the download mode.
Any help is welcome
Click to expand...
Click to collapse
I get same thing(galaxy s3 logo, black screen then normal boot when try accessing recovery) some time ago after installing philz reco, i flashed another recovery and now runs well, it sounds so strange that you still cant get at least stock recovery after a repartition and a full system reinstall... Maybe something get broke in the hardware...
Hello..!!
I need some help here. I tried to flash a custom ROM (X-Note (build 6.0) for Galaxy S5 GM900F) and then flash a new bootloader, the problem is that my device will never pass the booting process. I was stuck with the logo and black screen. I have searched and tried tons of tutorials and fixes but have not solved it.
I even tried to wipe Dalvik cache, wipe data, format system. I even put out the battery and leave it for sometimes, then on but the problem is still there.
This link to bootloader that I downloaded and flashed using Odin (after successfully installing custom ROM) and also the instructions that I followed to install the custom ROM.
https://www.androidfilehost.com/?fid=23622183712475277
When I try to re-install stock Samsung via Odin, it shows a Fail message. I don't know where to go from here and I'm really worry that my phone will never come to work.
Please help me to solve it.
..
fffft said:
I'm too busy today to describe this in detail.. but here are a few comments that may help you.
First, it is fixable. Usually it's enough to boot to recovery mode (phone off, then press and hold home + volume up + power buttons). Then from the recovery mode menu, choose wipe system cache. Then reboot. If you still have an issue then try a system data format from the Settings menu (this will erase user files!).
And as a last resort, restore a backup (if you have one) or a full, stock firmware image with Odin or Heimdall. Odin is infamous for being a bit picky, so don't panic if you get a failed message. That happens to all of us. Look for a detailed Odin tutorial or how to flash back to stock firmware thread that has Odin tips e.g. use a different USB cable + USB port. Temporarily turn off anti virus on your PC.. If the Odin write fails, do not close the Odin window. Just pull the battery and USB cable from your phone again.. put the battery back.. go back to download mode (home + volume down + power), plug the USB cable back, then press the start button in Odin again. It's important that the Odin window was open the whole time.
It may take a few tries (Odin can be frustrating) but you'll succeed.
.
Click to expand...
Click to collapse
Thanks for your words, you give me some hope because I thought my phone is now useless. I'll try again as you said.
Hello guys I need your help plz for my new grand 2 phone
Phone model: Galaxy grand 2 sm-g7102.
Android: kitkat 4.4.2 ,rooted without using custom recovery.
I have rooted my grand 2 mobile using kingroot app without using any custom recovery
and it worked fine.
the problem started when I have installed Gltools 1.0.7 and give it root permission then my mobile screen turned off and mobile didn't respond.
then i do the following press volume up+home+power buttons and the mobile restart in recovery mod i press the first option
reboot system now and then screen stuck at first boot screen .
I wiped my data ,cache and factory reset and no benefit of that .
what i have to do plz help me
abbody said:
Hello guys I need your help plz for my new grand 2 phone
Phone model: Galaxy grand 2 sm-g7102.
Android: kitkat 4.4.2 ,rooted without using custom recovery.
I have rooted my grand 2 mobile using kingroot app without using any custom recovery
and it worked fine.
the problem started when I have installed Gltools 1.0.7 and give it root permission then my mobile screen turned off and mobile didn't respond.
then i do the following press volume up+home+power buttons and the mobile restart in recovery mod i press the first option
reboot system now and then screen stuck at first boot screen .
I wiped my data ,cache and factory reset and no benefit of that .
what i have to do plz help me
Click to expand...
Click to collapse
flash stock firmware.
go to sammobile.com
Search for grand 2 firmware
then download it.
The firmware must base on your country.
after that flash using odin.
after complete. Remove battery then insert it again.
go to recovery
wipe everything
then reboot system
wait about 10 minutes
congrats your phone is normal again
Solution to your problem:
You will need to download the NK1 version of kitkat 4.4.2 stock firmware.
1) install samsung kies or samsung usb drivers so that your PC will detect your phone.
2) Switchoff your phone first and put it in download mode by pressing volume down and home button and power button at the same time.
3) connect your phone to your PC through the usb cable and start odin. (The com port turns blue in odin which means phone is detected).
4) In odin, check the "Nand erase all" in the checkbox and then click on "AP" buttion and select the "G7102DDUBNK1_G7102ODDBNK1_G7102DDUBNK1_HOME.tar" file.
5) Click the start button and wait for 5 mins till the OS is installed.
6) After installation, on your phone it might show 'memory damaged' and 'erase memory'. Don't worry, nothing is damaged or serious, just click to reset and everything will be fine.
7) Done!
I have provided the NK1 version link to you from my google drive account:
https://drive.google.com/folderview...03NF9WUzJLTHVSVnkzWWN5aFVQSzVOS28&usp=sharing
(Please hit thanks if I helped you)
Thanks guys
Problem solved and it is working now :fingers-crossed:
I have this same problem and I downloaded the above file and followed the instructions accordingly, after flashing it is still stuck at REBOOTING TO RECOVERY for about one hour now.I guessing it might be related to hardware.
mbond said:
I have this same problem and I downloaded the above file and followed the instructions accordingly, after flashing it is still stuck at REBOOTING TO RECOVERY for about one hour now.I guessing it might be related to hardware.
Click to expand...
Click to collapse
Which firmware were you on before the first boot loop? Flash that firmware, and don't forget to pull the battery afterwards.
(Don't hit thanks, hit the phone on a pillow/bed of you think its hardware related).
abbody said:
Hello guys I need your help plz for my new grand 2 phone
Phone model: Galaxy grand 2 sm-g7102.
Android: kitkat 4.4.2 ,rooted without using custom recovery.
I have rooted my grand 2 mobile using kingroot app without using any custom recovery
and it worked fine.
the problem started when I have installed Gltools 1.0.7 and give it root permission then my mobile screen turned off and mobile didn't respond.
then i do the following press volume up+home+power buttons and the mobile restart in recovery mod i press the first option
reboot system now and then screen stuck at first boot screen .
I wiped my data ,cache and factory reset and no benefit of that .
what i have to do plz help me
Click to expand...
Click to collapse
For future!
Just flash compatible kernel
Press THANKZ
Shane_Picardo said:
Solution to your problem:
You will need to download the NK1 version of kitkat 4.4.2 stock firmware.
1) install samsung kies or samsung usb drivers so that your PC will detect your phone.
2) Switchoff your phone first and put it in download mode by pressing volume down and home button and power button at the same time.
3) connect your phone to your PC through the usb cable and start odin. (The com port turns blue in odin which means phone is detected).
4) In odin, check the "Nand erase all" in the checkbox and then click on "AP" buttion and select the "G7102DDUBNK1_G7102ODDBNK1_G7102DDUBNK1_HOME.tar" file.
5) Click the start button and wait for 5 mins till the OS is installed.
6) After installation, on your phone it might show 'memory damaged' and 'erase memory'. Don't worry, nothing is damaged or serious, just click to reset and everything will be fine.
7) Done!
I have provided the NK1 version link to you from my google drive account:
https://drive.google.com/folderview...03NF9WUzJLTHVSVnkzWWN5aFVQSzVOS28&usp=sharing
(Please hit thanks if I helped you)
Click to expand...
Click to collapse
I have same problem, please share the download link.
Hello
Since this morning my Note 3 has died. I went to turn it on and it did not go beyond the initial Samsung boot screen.
I have already tried almost everything:
- Enter in recovery mode and make wipe dalvik and cache
- Enter in recovery mode and make wipe factory reset
- Install a new ROM for Odin
When Odin finishes, he gives me the PASS in green as all correct. I start the phone, enter the initial configuration screens, let me put the language, wifi, Google account but when the automatic configuration of the applications starts, it restarts and loops in trying to boot, but does not pass the Samsung logo.
I tried to install the ROM again, in case there had been any problems during the installation (despite giving the PASS in green), but it does not work.
The only thing I can think of is to put another type of ROM of those in which the option Re-Partition is marked, which I think is more exhaustive, but I'm not clear what kind of ROMs those are.
I would appreciate any help with the ROMs with Re-Partition, or any other suggestion that you could give me, to see if I can resuscitate it.
Are you performing a factory reset after flashing a stock ROM with Odin and before the phone boots the stock ROM for the first time?
but when the automatic configuration of the applications starts, it restarts
Reads as an app or something is the problem .
Thank you very much for your responses. After searching a lot, I found a ROM of 4 files + PIT. After installing it, the phone works correctly.