I dunno what went wrong here...
1) I have GT-I9505 (SSN: -I9505GSMH). I installed Galaxy S4 toolkit
2) Reboot into download mode. Used toolkit/Odin to root phone. Boots up. See SU.
3) Reboot into download mode. Used toolkit/Odin. Flashed TWRP Recovery
4) Phone boots up normal. Reboot into TWRP recovery. Did a factory Reset. Format.
5) Installed Zip (Latest Omega 9.0 ROM), unchecked the things I didn't want to install. Completed install, no errors reported. Rebooted.
6) Phone stuck on Samsung boot screen. I left it overnight thinking sometimes it may take 15 mins to boot system after new install.
7) Woke up, battery dead. Tried to charge phone. No charging indicators when plugged in. With whatever juice I had left I booted into TWRP recovery, it starts to charge again as I see the % batter increase after 5 mins.
-=-=-=-=- Did the Following to try to repair
a) Reinstalled Omega, this time leaving alll options on. Rebooted, stuck in Samsung boot
b) Flashed Phil CWM touch recovery, did complete wipe to install new ROM. Rebooted into Phil recovery. Flashed OMEGA. Reboot, stuck in Samsung boot.
c) Rebooted into Phil recovery, installed echo ROM, rebooted. Black screen. Rebooted into Phil. This time cannot get into recovery.
d) Started panicking, used Odin flashed TWRP. Would not flash. Something displayed about PIT error. Flashed Phil again. Reboot into recovery, WORKS! (recovery only). Went back into Download mode flashed TWRP. Rebooted, also WORKS!. Did a factory wipe. During wipe there was an error. Format, factory reset, error during wipe. Flashed OMEGA. Reboot. Stuck on samsung boot loop.
e) Downloaded official Samsung kernal for i9505 thinking it was the full flash rom. Flashed with ODIN (hoping to put everything back to factory). Completed flash, phone boots. I get OMEGA ANIMATION!!! Waited for 15 mins. Stuck on Animation. Reflashed TWRP. Rebooted, installed OMEGA...again. Stuck on samsung boot screen.
-=-=-= Kinda frustrated. What did I do wrong in the beginning?
There are so many official roms for the S4 based on region. What can I do to put it back to factory again? I purchased phone in Australia @ Samsung store. I figured download the Australia ROM but there are like 5 of them 4 being network branded roms I think. THe other one XSA is unbranded?
I tried searching for help but so far nothing works.
omega ROM or any other custom ROM uses single CSC so before booting into system you must boot into stock recovery to apply CSC of that ROM, download stock recovery of that firmware the ROM was built from
after applying CSC it will work if not flash Omega 9.0 again , it will work :good::good:
arnob_xperia said:
omega ROM or any other custom ROM uses single CSC so before booting into system you must boot into stock recovery to apply CSC of that ROM, download stock recovery of that firmware the ROM was built from
after applying CSC it will work if not flash Omega 9.0 again , it will work :good::good:
Click to expand...
Click to collapse
Thanks for responding
So I take it when I did the full factory wipe and FORMAT the formatting part erased the CSC?
The steps are:
1) Find stock recovery of the original ROM OMEGA was built on. Use odin, flash that specific recovery. ( I might as well do a complete flash of the original stock firmware)
2) Use odin, replace recovery with TWRP, flash Omega this time no formatting
Reboot should be ok?
kabloomz said:
Thanks for responding
So I take it when I did the full factory wipe and FORMAT the formatting part erased the CSC?
The steps are:
1) Find stock recovery of the original ROM OMEGA was built on. Use odin, flash that specific recovery. ( I might as well do a complete flash of the original stock firmware)
2) Use odin, replace recovery with TWRP, flash Omega this time no formatting
Reboot should be ok?
Click to expand...
Click to collapse
first use CWM or TWRP or whatever you want and format everthing
flash a fresh firmware(latest i prefer)
then flash stock recovery via odin of the built version what v9 was used, simply reboot to recovery and it will say MULTI CSC APPLIED from fresh frimware you used
then flash TWRP/CWM and flash v9
again simply reboot to recovery and it will say MULTI CSC APPLIED from V9
it will reboot, you must need to apply CSC to boot your phone
I can confirm this!
I was trying to flash Omega 9 on top of jamal's 4.3 and my phone always booted to recovery. So I restored my stock touchwiz (no custom recovery or even root) nandroid backup and applied Omega 9: it worked!
douglascamata said:
I was trying to flash Omega 9 on top of jamal's 4.3 and my phone always booted to recovery. So I restored my stock touchwiz (no custom recovery or even root) nandroid backup and applied Omega 9: it worked!
Click to expand...
Click to collapse
thats right stock recovery boot is needed to apply CSC
problem
I need help. I am on stock build i9505XXUBMG5. then I rooted it using CF-autoroot. and i used the 1.85 version of ODIN. (Does the version of ODIN affect how the phone is rooted?) Anyways, After that, it is rooted. then after some time, my Wifi is not working or not turning on. I checked google and found the *#0011# method and turned off the Wifi power saving. Then, at first, it worked. After a while, the problem insists. but randomly turns on. I observed that in the *#0011# -> wifi window, the state is power off. but when it is completely not turning on, the state is now disconnected. How can I fix this?
I tried flashing Omega ROM, because there was a wifi fix on that ROM. But when I finished flashing it and continue to reboot, it's stuck on the boot animation. It is not even the Omega robot animation, just the original animation. (Another problem) i tried wiping cache, delvik cache and data but nothing happens.
macoy_412 said:
I need help. I am on stock build i9505XXUBMG5. then I rooted it using CF-autoroot. and i used the 1.85 version of ODIN. (Does the version of ODIN affect how the phone is rooted?) Anyways, After that, it is rooted. then after some time, my Wifi is not working or not turning on. I checked google and found the *#0011# method and turned off the Wifi power saving. Then, at first, it worked. After a while, the problem insists. but randomly turns on. I observed that in the *#0011# -> wifi window, the state is power off. but when it is completely not turning on, the state is now disconnected. How can I fix this?
I tried flashing Omega ROM, because there was a wifi fix on that ROM. But when I finished flashing it and continue to reboot, it's stuck on the boot animation. It is not even the Omega robot animation, just the original animation. (Another problem) i tried wiping cache, delvik cache and data but nothing happens.
Click to expand...
Click to collapse
Do you have an IMEI showing on your phone? What recovery did you use to flash Omega?
It matters, because some recoveries will screw it up.
Do you try to install with Philz recovery?
Sent from my GT-I9505 using xda premium
macoy_412 said:
I need help. I am on stock build i9505XXUBMG5. then I rooted it using CF-autoroot. and i used the 1.85 version of ODIN. (Does the version of ODIN affect how the phone is rooted?) Anyways, After that, it is rooted. then after some time, my Wifi is not working or not turning on. I checked google and found the *#0011# method and turned off the Wifi power saving. Then, at first, it worked. After a while, the problem insists. but randomly turns on. I observed that in the *#0011# -> wifi window, the state is power off. but when it is completely not turning on, the state is now disconnected. How can I fix this?
I tried flashing Omega ROM, because there was a wifi fix on that ROM. But when I finished flashing it and continue to reboot, it's stuck on the boot animation. It is not even the Omega robot animation, just the original animation. (Another problem) i tried wiping cache, delvik cache and data but nothing happens.
Click to expand...
Click to collapse
At this point I think it is the CSC issue arnob-xperia mentioned.
This is how I corrected my issue.
1) Omega v10 uses newer base FW. In their description it tells u. (ex: ver 9 uses XUBMG5). Search on the i9505 forums here. I can't link for some reason I can't see any of the stickied threads, especially the one listing all avail stock firmwares.
Flash into Philz or TWRP do a complete wipe of everything including data. etc.
You MUST download the full firmware, Not just the smaller kernel and recovery or csc. The full stock fw is usually over 1.6 GB. Anything around that range and u got the right one for Odin flash with the md5. Use Odin to flash. I used 1.85 and it was fine.
2) Once done it will reboot and in theory you are stock everything. At this point, for me somehow the phone got stuck in fricken boot loop. I pulled out battery, reboot into stock recovery and made sure I saw the multicsc. Rebooted. Still boot loop.
After hours of doing all sorts of things and putting the phone aside for a day. Came back, flashed the stock fw again using Odin. Reboot into recovery. Check the multi csc. Reboot. Stuck in boot loop. Reboot to download mode. Then I decided to ROOT the phone for ****s and giggles. This worked!
Phone booted.
3) Now you have stock (for that specific OMEGA fw) w/ the matching CSC. From here on follow OMEGA flash instructions for the specific things it tells u to wipe. DO NOT DO A FULL WIPE/FORMAT like I did (what got me in the mess to begin with).
** For Galaxy S3s, S4s, for some reason I've always had problems with TWRP. I had better luck using Philz. Everyone's personal experience varies on this one.
** I think the problem has to do with the CSC which handles specific region phone and carrier modes. This doesn't mean that it won't work if you use a diff region CSC. Just that it has to match the FW base you are using otherwise you have all sorts of problems. After that you can go in android and setup your APNs etc if you have probs with data. I didn't have this problem and was testing using the UK fw base on AU network sim.
*** Why does Samsung make things so damn complicated. I remember way back in 2k3 using fricken ODIN (samsung flashing utitility) to flash **** and it was the same setup as now. This whole crap about CSC pairing is a bit annoying. It is bad enough there are 6+ variations of S4s lol...
Hope this helps.
wifi problem
kabloomz said:
At this point I think it is the CSC issue arnob-xperia mentioned.
This is how I corrected my issue.
1) Omega v10 uses newer base FW. In their description it tells u. (ex: ver 9 uses XUBMG5). Search on the i9505 forums here. I can't link for some reason I can't see any of the stickied threads, especially the one listing all avail stock firmwares.
Flash into Philz or TWRP do a complete wipe of everything including data. etc.
You MUST download the full firmware, Not just the smaller kernel and recovery or csc. The full stock fw is usually over 1.6 GB. Anything around that range and u got the right one for Odin flash with the md5. Use Odin to flash. I used 1.85 and it was fine.
2) Once done it will reboot and in theory you are stock everything. At this point, for me somehow the phone got stuck in fricken boot loop. I pulled out battery, reboot into stock recovery and made sure I saw the multicsc. Rebooted. Still boot loop.
After hours of doing all sorts of things and putting the phone aside for a day. Came back, flashed the stock fw again using Odin. Reboot into recovery. Check the multi csc. Reboot. Stuck in boot loop. Reboot to download mode. Then I decided to ROOT the phone for ****s and giggles. This worked!
Phone booted.
3) Now you have stock (for that specific OMEGA fw) w/ the matching CSC. From here on follow OMEGA flash instructions for the specific things it tells u to wipe. DO NOT DO A FULL WIPE/FORMAT like I did (what got me in the mess to begin with).
** For Galaxy S3s, S4s, for some reason I've always had problems with TWRP. I had better luck using Philz. Everyone's personal experience varies on this one.
** I think the problem has to do with the CSC which handles specific region phone and carrier modes. This doesn't mean that it won't work if you use a diff region CSC. Just that it has to match the FW base you are using otherwise you have all sorts of problems. After that you can go in android and setup your APNs etc if you have probs with data. I didn't have this problem and was testing using the UK fw base on AU network sim.
*** Why does Samsung make things so damn complicated. I remember way back in 2k3 using fricken ODIN (samsung flashing utitility) to flash **** and it was the same setup as now. This whole crap about CSC pairing is a bit annoying. It is bad enough there are 6+ variations of S4s lol...
Hope this helps.
Click to expand...
Click to collapse
I did flash the Omega v9.1 and applied the wifi fix but the wifi is still broken. I tried unrooting it by flashing the original rom and formatting the data but the wifi is still broken. I can't turn it on. Thanks for the instructions anyways. ))
no pit partition
also, when i tried to root it again, it fails and says there is no PIT partition..
Where is the csc in TWRP so I can so what ones on the phone..??
What stock firmware can I use for a Orange Network in the UK.
GT-i9505 stuck on boot when upgraded from omega v16 to v21
Hello guys,
Well, I followed all the instructions and flashed new bootloader and new modem and after that I installed omega v21 with Full swipe. After that I ended up stuck in boot animation. :s What to do? I already tried to re-flash modem and bootloader, updated CWM and tried to re-install that v21 and after that I flashed twrp over cwm and tried to re-install v21 but always I ended up stuck in that boot animation. :S All installs were successful, but it just wont boot.
What to do?
Hopefully you understand my problem.
Cheers from Finland!
Nico
EDIT:
Ok, I flashed omega rom v19 with full wipe and tried to boot. Didnt work, but then I installed Kies to my computer, opened Kies, Plugged USB in and started my phone and then Kaboom! It booted. What exactly happened there?
BizK1d said:
Hello guys,
Well, I followed all the instructions and flashed new bootloader and new modem and after that I installed omega v21 with Full swipe. After that I ended up stuck in boot animation. :s What to do? I already tried to re-flash modem and bootloader, updated CWM and tried to re-install that v21 and after that I flashed twrp over cwm and tried to re-install v21 but always I ended up stuck in that boot animation. :S All installs were successful, but it just wont boot.
What to do?
Hopefully you understand my problem.
Cheers from Finland!
Nico
EDIT:
Ok, I flashed omega rom v19 with full wipe and tried to boot. Didnt work, but then I installed Kies to my computer, opened Kies, Plugged USB in and started my phone and then Kaboom! It booted. What exactly happened there?
Click to expand...
Click to collapse
Hi, I am having the same problem. First I installed the new firmware (NA5) and modem, tested it with the Omega ROM v21 and boot caught on so now tested the rom Fox Hound 4.1 and am having the same problem.
Kies tested this option but have not had the same luck as you. = /
Anyone know the reason? The rom Google Edition Jamal runs on my phone.
i9505
Hi guys, I have a little bit of a problem and I was wondering if anybody can help me... I had CM 10.1.3 installed on my S4 I9505 intl and after installing Adam kernel the phone didn´t boot up anymore, so I went to Recovery and I did a wipe data/ factory reset, wipe cache and also format system and format /data and /data/media (/sdcard) hoping to install the official rom via Odin using the DL mode. After reboot, I got the message Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again. First, I tried to install the official rom by booting up the phone in DL mode but it didn´t work, the update stops right at the beginning of the provess, then I tried to recover via Kies but Kies doesn´t recognize the phone neither. So I installed CWM again via Odin ( successfully ) and flashed CM again. Can anyone help me figure out what´s wrong and what needs to be done in order to be able to flash the stock rom ? Thanks !!
just download a .zip variant and flash it via CWM
rebel1735 said:
just download a .zip variant and flash it via CWM
Click to expand...
Click to collapse
Yes I thought of that but I can´t find a .zip variant, do you by any chance have a link for that ?
Why would you flash a kernel for Samsung roms when you are on a CM rom? That will not work.
So from what I understand, Odin works but you can't flash a stock rom? What stock rom did you want to flash? I hope that you didn't try to flash a Knox enabled stock rom. Did you try other stock roms?
Lennyz1988 said:
Why would you flash a kernel for Samsung roms when you are on a CM rom? That will not work.
So from what I understand, Odin works but you can't flash a stock rom? What stock rom did you want to flash? I hope that you didn't try to flash a Knox enabled stock rom. Did you try other stock roms?
Click to expand...
Click to collapse
I am trying to flash I9505VJUBMG3_I9505ZTOBMG3_I9505VJUBMG3 and yes Odin works I just can´t flash the stock ROM. I installed this rom many times before and I also tried an older version as well and still no luck.
I was having some issue with connecting to wifi every time my phone would reboot. I tried factory resets and different roms. I then clicked nand erase
all thinking this would clean all data before installing stock rom again. I am now stuck at the tmobile 4glte screen. From what I read so far I wiped my partition and need a pit file. I have tried a few online but none have been successful. I was on kitkat. Please someone help me save my Note. I need my companion back.
Immaculus said:
I was having some issue with connecting to wifi every time my phone would reboot. I tried factory resets and different roms. I then clicked nand erase
all thinking this would clean all data before installing stock rom again. I am now stuck at the tmobile 4glte screen. From what I read so far I wiped my partition and need a pit file. I have tried a few online but none have been successful. I was on kitkat. Please someone help me save my Note. I need my companion back.
Click to expand...
Click to collapse
Flash stock rom with odin....
I'm downloading the stock firmware from sammobile now. Will that have the partition info as well? 45mins left. will update if succesfull. Thanks for the reply.
rayman95 said:
Flash stock rom with odin....
Click to expand...
Click to collapse
stock rom fails. doesn't get past partition. Fail. need a pit file i believe unless I'm totaling doing something wrong.
Note 3 Tmobile USA
Found a fix.
Flashed custom recovery via Odin.
Used recovery to format which got the partition needed.
SOLVED
So...I was using CM13 for my N910C and decided to go back to stock.
First I simply tried to flash the stock rom on Odin, but I got the FAIL message every time, so I did some research and figured it could be some problem with the PIT file. Download one for the N910C, flashed it with the stock rom and Odin did the process normally.
After that, I got in a boot loop, so I entered the recovery mod, did a factory reset and wipe cache and the boot loop continues.
It just shows the first Galaxy Note 4 logo for like 2s, then screen goes black and it repeats over and over again.
I tried to flash the rom again, tried to flash the pit file again, tried a different pit file (obviously for n910c) and no luck.
Any ideas?
Thanks! And sorry for the poor english!
You have to backup your imei, then format efs partition and flash with odin.
menaum said:
So...I was using CM13 for my N910C and decided to go back to stock.
First I simply tried to flash the stock rom on Odin, but I got the FAIL message every time, so I did some research and figured it could be some problem with the PIT file. Download one for the N910C, flashed it with the stock rom and Odin did the process normally.
After that, I got in a boot loop, so I entered the recovery mod, did a factory reset and wipe cache and the boot loop continues.
It just shows the first Galaxy Note 4 logo for like 2s, then screen goes black and it repeats over and over again.
I tried to flash the rom again, tried to flash the pit file again, tried a different pit file (obviously for n910c) and no luck.
Any ideas?
Thanks! And sorry for the poor english!
Click to expand...
Click to collapse
The process to go back from cm 13 to stock 5.1.1 is tedious, Anyway read this http://forum.xda-developers.com/note-4/help/fix-note4-exynos-n910c-bootloop-problem-t3312161
Hello,
trying to help a pal bring his phone back to life.
Used the latest version of odin to flash an official rom. Odin showed that it had passed and flung up no errors. Boot loop remained.
Eventually tracked down the correct carrier via sammobile and downloading it.
If this doesn't work then I am out of idea's.
Anything else I could do to fix it or could it be hardware?
Before flashing, uncheck everything in Odin. Flash rom and, when you see the word "reset" in the status window, remove the USB cable, remove battery, replace battery, use button combination to boot into recovery, factory wipe, reboot.
Thanks ..... The only thing I didn't try there was factory wipe when in recovery
Sent from my iPhone using Tapatalk
flashed the official carrier rom and unfortunately it still boot loops.
Odin is showing pass every time i flash a rom and no errors
crazygoldfish said:
flashed the official carrier rom and unfortunately it still boot loops.
Odin is showing pass every time i flash a rom and no errors
Click to expand...
Click to collapse
Also it only boots into doing mode not recovery
thinking its hardware
now when i try to flash any roms at all its failing, even roms that previously passed.