I'm sorry but I'm not the most tech savvy person on this planet but I will do my best to explain my situation
Two nights ago my S5 got stuck on Samsung logo and has not done anything else since. I CAN NOT get it into Recovery Mode or Safe Mode.....only Download mode. After researching I decided to flash the stock firmware for SM-G900A. Downloaded the firmware from RapidGator. And downloaded Odin 3 v3.09. Also downloaded Keis3. First time I tried to run Odin, it told me PIT file was not found (or something like that). I'm not sure why I have to have the PIT file but I found it in a thread on XDA and added it to the PIT section in Odin.
This is the message screen on Odin
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900AUCU1ANCE_G900AATT1ANCE_G900AUCU1ANCE_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My phone says
ODIN MODE
PRODUCT NAME: SM-G900A
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
REACTIVATION LOCK(KK): OFF
KNOX WARRANTY VOID: 0X0
QUALCOMM SECUREBOOT: ENABLE (CSB)
AP SWREV; S1, T1, R1, A2, P1
UDC START
MMC: mmc_read fail
SECURE CHECK FAIL : PIT
ODIN : flash read failure
Is there something that I am doing wrong? A step I'm missing? Or is my phone done for?
Any help would be really appreciated
UPDATE: tried flashing firmware again with PIT file and this is the message I'm getting now
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G900AUCU1ANCE_G900AATT1ANCE_G900AUCU1ANCE_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Related
Hello,
I have a GT-I9505 which was under 4.3
I did the update OTA 4.4.2 and redemarage bootloop
impossible to get to recovery I left a red message at the top: moviNAND Checksum Confirmation Fail
I try to flash via odin with the latest firmware 4.4.2 XEF and here the result:
Enter CS for MD5 ..
Check MD5 .. Do not unplug the cable ..
Please wait ..
I9505XXUFNC4_I9505OXXFNC3_I9505XXUFNC4_HOME.tar.md5 is valid.
Checking MD5 finished Sucessfully ..
Leave CS ..
Added!
Odin v.3 engine (ID: 5) ..
File analysis ..
SetupConnection ..
Initialzation ..
Get PIT for mapping ..
There is no PIT partition.
All threads completed. (succeed 0 / failed 1)
Do you have any ideas?
Download and unzip this file: HERE and flash it like in the pic attached (+ the stock firmware u downloaded). Reboot manually then.
OTA update samsung missed
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNC4_I9505OXXFNC3_I9505XXUFNC4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
This is the result
chtiti said:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUFNC4_I9505OXXFNC3_I9505XXUFNC4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Added!!
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> FAIL!
<ID:0/006>
<ID:0/006> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
This is the result
Click to expand...
Click to collapse
if you use single tar file do not check re-partition option
open odin use default auto-reboot and F.reset time only
OTA update samsung missed
Hello,
same result.
Run as administrator (Right click on the icon)
Use Odin 3.07
If that doesn't work then download a 4.3 file and flash that onto the device.
OTA update samsung missed
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9505XXUEMKF_I9505OXXEMK3_I9505XXUEMKF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
<ID:0/006> Added!!
OTA update samsung missed
Do you think the JTAG can solve my problem?
Did you try basic stuff like:
A different usb cable
A different usb port
A different pc?
You are not running Odin on a virtual machine are you?
Did you try redownloading the firmware? Did you try other firmwares?
OTA update samsung missed
I tried everything! Nothing works!
Did you try flashing a custom recovery and then try to flash a custom rom from there?
OTA update samsung missed
re,
How do I flash a custom rom without access to recovery?
OTA update samsung missed
The S4 has gone on a JTAG date.
Told you please uncheck re-partition option...you use single file
Sent from my GT-I9500
chtiti said:
re,
How do I flash a custom rom without access to recovery?
Click to expand...
Click to collapse
Can't you reflash the recovery?
Hello,
I had Alliance ROM and tried to flash Jasmine 5.0, but the phone restarted before it finished and now the phone only show either the "Samsung Galaxy Note 3" logo or download mode, recovery is gone.
When I try to enter recovery mode, the phone vibrates once and the screen stays black if i release the power button, but keep holding volume up and home.
If i dont release power, it keeps vibrating and a black screen.
I tried restoring to any possible image, MJE, NC2, NC4 and OB6, using Odin 3.09. All fail.
Tried using a Pit file, since the other error states that it cant find a pit file, that also failed.
Odin log is with Pit file:
ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900VVRUEOB6_N900VVZWEOB6_N900VVRUEOB6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Erase...
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Without Pit file:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N900VVRUEOB6_N900VVZWEOB6_N900VVRUEOB6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
On the phone, it says the following:
odin mode
product name: sm-n900v
current binary: Samsung official
system status: official
knox kernel lock:0x0
knox warranty void:0x0
qualcom secureboot: enable (csb)
AP SWREV: S1, T1, R1, A2, P1
write proctection: Enable
UDC start (this is in red)
MMC: mmc_write fail
odin: flash read failure (This is in red)
That list is the same, no matter what.
Is anything else I can try or this phone just gone?
Please help!:crying:
Anyone??
NeoMorpheus1337 said:
Anyone??
Click to expand...
Click to collapse
Go to either a Verizon Company store or to Best Buy and go to the Samsung experts (at the Samsung section) and have them do a complete flash.
They can flash it to pure stock. There should be no issues since Knox and Warranty fuses are not blown
Just tell them it got knocked off the desk in the middle of an upgrade and the battery popped out.
Sent from my Note 3 via Tapatalk
Damn, thats a good advice and it didnt occur to me before.
I actually called Samsung and after talking to one of their techs, they recommended to send it to them.
Sadly, it will cost 80 bucks, but per one of the devs here, it does looks like a part of knox locked the storage and only a new motherboard can fix this.
Either way, 80 bucks is not that bad, given that the alternative is buying another phone for 250 or so.
I tried to root my phone for the first time. I saw a guide on Youtube and decided why not. It was relatively easy to follow and I am sure I followed it 100% correctly. I managed to see SuperSU, however, it failed to install the proper packages and would always tell me to reboot. Other problems I encountered were Google Play would not open, and every couple of seconds a service would stop working along with it. So I decided to un-root my phone. I found a factory version SM-G395PVPU2APC5, went into download mode, and as of right now it has been stuck here every since. I can alternate between download mode and boot mode but that's about it. I couldn't properly install the factory version because this message pops up every time I try:
ODIN MODE (HIGHSPEED)
PRODUCT NAME: SM-G395P
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
FAP LOCK: OFF
WARRANTY VOID: 0x0
QUALCOMM SECUREBOOT: ENABLE
AP SWAEV: B4(2,1,1,1,) K1 S3
SECURE DOWNLOAD: ENABLE
SW REV CHECK FAIL: [system]Fused 3 > Binary 1
On Odin it has a similar message:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please, please help. I have looked everywhere for hours to try and find a solution. I have downloaded gigabytes upon gigabytes of different factory versions, I think I am going insane because of this problem.
hi. i screwed up in trying to root my phone thinking it would be an easy process like i had when i had jailbroken my old iphones....nope
Im pretty sure i have the stock firmware files. if someone can link me a download for the SM-G935v firmware with marshellow would be awseome too.
when trying to flash i am getting a fused 3 > binary 1 message on my phone
odin says:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> skip file list for home binary
<ID:0/005> persist.img.ext4
<ID:0/005> Home Binary Download
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
my phone says :
product name: sm-g935t
currenr binary: official
system status: official
fap lock: on
warrently void: 0x0
It is because you forgot to enable OEM unlocking, and now you have FRP lock, but don't worry, you just have to flash stock ROM again using odin ( download firmware from Sammobile ).
And next tine time you try to root, do not forget to enable OEM unlocking in developers menu.
Hi everyone,
I've been out of the android rooting world for a while now but I was sent a Galaxy s7 Edge from Samsung as part of their device insights program. I used it for six months as required and after that I tried to root it. Long story short I'm stuck in a bootloop. Cant get into recovery either, only download mode.
Download mode says:
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-G935T
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: OFFICAL
FAP LOCK: ON
WARRANTY VOID: 0x0
QUALCOMM SECUREBOOT: ENABLE
AP SWREV: B4(2, 1, 1, 1, 1) K1 S3
SECURE DOWNLOAD : ENABLE
SW REV CHECK FAIL : [system]Fused 3 > Binary 2
I attempted to ODIN back to stock and here is what happened
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> FAIL! (Auth)
<ID:0/004>
So does anyone know how I can just get back to stock?
mpalomba3 said:
Hi everyone,
I've been out of the android rooting world for a while now but I was sent a Galaxy s7 Edge from Samsung as part of their device insights program. I used it for six months as required and after that I tried to root it. Long story short I'm stuck in a bootloop. Cant get into recovery either, only download mode.
Download mode says:
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-G935T
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: OFFICAL
FAP LOCK: ON
WARRANTY VOID: 0x0
QUALCOMM SECUREBOOT: ENABLE
AP SWREV: B4(2, 1, 1, 1, 1) K1 S3
SECURE DOWNLOAD : ENABLE
SW REV CHECK FAIL : [system]Fused 3 > Binary 2
I attempted to ODIN back to stock and here is what happened
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> FAIL! (Auth)
<ID:0/004>
So does anyone know how I can just get back to stock?
Click to expand...
Click to collapse
I had the same issue. I changed the usb port i was using on my computer.
Update: Solved using Samsung smart switch program
SW REV CHECK FAIL : [system]Fused 3 > Binary 2
You were on ver 3 of the binary trying to odin a version 2 build. You can't go backwards, only same bl version or newer. The bl version is built into the build number. For example, G935TUVU4APK1 build the 4 designates the bl version. You can flash that over version 3 (what you were on) but none of the builds with a 2 in them would work. Hope that helps explain it.
Well I have no problem with the Nouggat Stock ROM but in fact I´m facing the same issue, so, do anyone have the unlcoked firmware in order to be free to use any sim in any country?
Thanks in advance.
Best regards.
Gowmi.
Ok this is the current and correct one.
https://theunlockr.com/2016/09/03/root-samsung-galaxy-s7-s7-edge/
Cheers.