[Q] LG G2 D800 - Gone Progressively worse.. Looks like completely bricked - G2 Q&A, Help & Troubleshooting

Hi,
I have a LG G2 D800 (ATT Black version) which I was running with cm 11 for a long time.. Last week I got curious and tried to install CM12 on it and that's where started my nightmare.
To begin with, I think I flashed the wrong twrp version (d802) instead of d800.. So I was stuck for a while.. I finally was able to recover from that and Installed CM12. The install went ok, but the phone would freeze and turn off.. It wouldn't turn back on unless I did a soft reset.. I tried a few times and then gave up.. With the nandroid backup that I had, I went back to cm11, but the problem started to follow me in CM11 as well.. The phone was constantly rebooting.. Sometimes the phone would stay on for 2-3 hours and sometimes it wouldn't stay on for 2 minutes.. So I got frustrated and went thru' different threads and finally went back to Stock Rom using the LGFlashtool method.. In stock rom, the phone booted up fine, but the rebooting issue started happening there as well.. The phone was definitely much stable under stock rom than CM11/CM12 but it won't still power off all of a sudden and I could go a couple of hours before noticing that it had turned off.. Frustrated with it, I started all over again to root and install twrp and that's when it went from Bad to worse.. Something happened with my TWRP flash and I was not able to go to recovery or download... I was stuck...
I tried several methods. 1 ) Using ubuntu was my first try.. I followed the initial steps (ls devices and gdisk -l command) and after I ran the first step (dd if=/home/med/Desktop/sbl1.img of=/dev/sdb2), my phone went into fastboot mode and ubuntu couldn't recognize my device. after that.. I couldn't run the remaining commands..
2) since I was stuck in fastboot, I followed the fastboot method from another thread by downloading the fastboot and laf.img.... The phone was responding and said recovery erased successfully, but it kept going back to fastboot.. When I tried a different laf.img file, that's when the phone rebooted and now wouldn't turn on at all..
No LG image, no recovery, no response.. I've tried all button combinations (holding vol down and power, power alone, all 3 buttons, vol+ and power)... nothing happens with the phone... Windows doesn't recognize the phone.. It says 'lg g2 qhsusb_bulk' but that's pretty much it..
Atleast until today morning I had a LG image flashing that tells me that the issue is a software / partition issue.. Now I don't know if I have fried something..
I bought the fone in november 2013 and hence its out of warranty.. . I'm not eligible for upgrade till November and I'm stuck with using a iphone 4s (ouch...) until then... It sucks big time to go from the g2 to the 4s... any thoughts or ideas?

I had the same problem when I flashed the wrong kernel.... This link helped me http://forum.xda-developers.com/showthread.php?t=2582142 one of these 7 solutions should help you....
I found this link on YouTube which is exactly like your case
http://m.youtube.com/watch?v=_d5b_osUTug
And the second link which I didn't try is
Sent from my Lightning D802 G2

Supracer said:
I had the same problem when I flashed the wrong kernel.... This link helped me http://forum.xda-developers.com/showthread.php?t=2582142 one of these 7 solutions should help you....
I found this link on YouTube which is exactly like your case
http://m.youtube.com/watch?v=_d5b_osUTug
And the second link which I didn't try is
Sent from my Lightning D802 G2
Click to expand...
Click to collapse
Thanks. I looked into that thread before. Unfortunately in my case the phone is not recognized in adb or fastboot. Adb shows no device listed whereas fastboot says waiting for device.
Lg flashtool doesnt do anything either.
Only thing is that fone was showing up as unknown device and by me pressing vol up and power and vol down, it shows up as qhusb bulk..

askthiru said:
Thanks. I looked into that thread before. Unfortunately in my case the phone is not recognized in adb or fastboot. Adb shows no device listed whereas fastboot says waiting for device.
Lg flashtool doesnt do anything either.
Only thing is that fone was showing up as unknown device and by me pressing vol up and power and vol down, it shows up as qhusb bulk..
Click to expand...
Click to collapse
Go to the Device Manager => device properties of the "unknown device" => Details => Hardware ID and search the value on the internet for a driver... Maybe with a driver you can get the phone to be recognized

Folks,
I finally was able to get my G2 working from a hard brick..
My final non working symptom : Blank Screen.. No download.. No recovery.. No LG logo… Windows was showing device as unknown device sometimes and sometimes as qhusb_bulk.
Steps that I followed: You need to know how to use fastboot.
1) Kept trying different combinations of the 3 buttons (power, vol + and Vol -). The one that worked for me was to unplug the phone from pc… Press all 3 buttons together for 15-20 seconds and will keys pressed, plug into the PC.
2) This put me in the fastboot mode.. Here I tried flash laf.img with several laf files. My phone was a lg g2 d800 (ATT variant). Nothing really worked..
3) So I downloaded the Stock Rom files (aboot, boot, dbi, laf, misc, modem, persist, recovery, rpm, sbl1, and tz images) from http://downloads.codefi.re/autoprime/LG/LG_G2). I flashed all these files using Fastboot and then after flashing, rebooted the phone.
4) The phone automatically went into AT&T update and at 3% failed with an error and booted into safe mode. (This is probably because when it got bricked, I accepted a OTA update on a rooted phone and I didn’t have twrp recovery either).
5) I came out of safe mode and booted normally and voila, I got the stock rom 4.2.2 on my phone.
Thanks so much to the various threads in XDA developers that I was able to fix this.. Much thanks to etm34 for this thread: http://forum.xda-developers.com/showthread.php?t=2681089
Also to Partager.info for this thread: http://forum.xda-developers.com/showthread.php?p=48765620#post48765620
And cms88168 for this thread http://forum.xda-developers.com/showthread.php?t=2477595
I had to use all these 3 threads above to get my g2 back to working..

Thanks for sharing

askthiru said:
Folks,
I finally was able to get my G2 working from a hard brick..
My final non working symptom : Blank Screen.. No download.. No recovery.. No LG logo… Windows was showing device as unknown device sometimes and sometimes as qhusb_bulk.
Steps that I followed: You need to know how to use fastboot.
1)Kept trying different combinations of the 3 buttons (power, vol + and Vol -). The one that worked for me was to unplug the phone from pc… Press all 3 buttons together for 15-20 seconds and will keys pressed, plug into the PC.
2)This put me in the fastboot mode.. Here I tried flash laf.img with several laf files. My phone was a lg g2 d800 (ATT variant). Nothing really worked..
3)So I downloaded the Stock Rom files (aboot, boot, dbi, laf, misc, modem, persist, recovery, rpm, sbl1, and tz images) from http://downloads.codefi.re/autoprime/LG/LG_G2). I flashed all these files using Fastboot and then after flashing, rebooted the phone.
4)The phone automatically went into AT&T update and at 3% failed with an error and booted into safe mode. (This is probably because when it got bricked, I accepted a OTA update on a rooted phone and I didn’t have twrp recovery either).
5)I came out of safe mode and booted normally and voila, I got the stock rom 4.2.2 on my phone.
Thanks so much to the various threads in XDA developers that I was able to fix this.. Much thanks to etm34 for this thread: http://forum.xda-developers.com/showthread.php?t=2681089
Also to Partager.info for this thread: http://forum.xda-developers.com/showthread.php?p=48765620#post48765620
And cms88168 for this thread http://forum.xda-developers.com/showthread.php?t=2477595
I had to use all these 3 threads above to get my g2 back to working..
Click to expand...
Click to collapse
Happy to see you solved.

All,
Even though I resolved my bricked G2, it is still giving me issues by turning off automically after a while... It looks like a hardware failure to me where it ceases to operate at times.. The phone has stayed on sometimes for an entire day and sometimes it goes off in 5 minutes.. I'm sending it to LG repair service.. Hopefully they fix it for me under warranty (even though it has been 13 months since i bought it)..

Related

[Q] help! stuck on fastboot

Hi
I tried flashing CWM Recovery on my new G2
but after flashing my phone boots and I see on the screen:
fastboot mode started
udc_start()
And it's stuck like that.
I tried downloading SDK and replacing recovery by fastboot commands, but my pc doesn't seem to recognize the phone.
After installing a usb driver I see in device manager that the driver is still not installed correctly.
I guess it's because my phone isn't loading, right? maybe it needs to be installed when Android is running?
I even tried factory reset (boot in recovery - power + vol up) but still no change
Please help me if you have an idea how, I only bought it last week and now it's bricked!
Thanks
additional information
my phone's model: D802
I downloaded the CWM image from here:
http://forum.xda-developers.com/showthread.php?p=46837114
my pc runs windows xp
thanks all
zionzakay said:
Hi
I tried flashing CWM Recovery on my new G2
but after flashing my phone boots and I see on the screen:
fastboot mode started
udc_start()
And it's stuck like that.
I tried downloading SDK and replacing recovery by fastboot commands, but my pc doesn't seem to recognize the phone.
After installing a usb driver I see in device manager that the driver is still not installed correctly.
I guess it's because my phone isn't loading, right? maybe it needs to be installed when Android is running?
I even tried factory reset (boot in recovery - power + vol up) but still no change
Please help me if you have an idea how, I only bought it last week and now it's bricked!
Thanks
Click to expand...
Click to collapse
try holding the power down for 15 seconds. phone should be completely of now. now hold volume up while plugging in usb. this should get you in download mode. now read this thread. or maybe read this thread first.
http://forum.xda-developers.com/showthread.php?t=2432476
gentlemandroid17 said:
try holding the power down for 15 seconds. phone should be completely of now. now hold volume up while plugging in usb. this should get you in download mode. now read this thread. or maybe read this thread first.
http://forum.xda-developers.com/showthread.php?t=2432476
Click to expand...
Click to collapse
thank you, but my phone is varrient-free, and I don't think any rom will work.don't see anything on the list that seems fit.
also, isn't there a way to only recover boot, and not wipe the rom entirely?
That'sa the reason why. You flashed recovery for Verizon and yours is D802 International. If you can still go to download mode, try here http://forum.xda-developers.com/showthread.php?t=2471370&highlight=brick or http://forum.xda-developers.com/showthread.php?t=2432476.
http://storagecow.eu/index.php?dir=Xda/LG+G2/Stock/ Here, choose only D802.

[Q] Hard bricked G2 after flash

Hi everyone
I may have bricked my G2. I use to have a Samsung Galaxy S which I flashed many times so I kinda know when I mess up with instructions. This time though, things look a bit more serious... Anyway, here is what happened:
I flashed the Cloudy G3 rom (1.0) for my G2 D802 32gb. Original rom was stock rooted 4.4.
I followed the instructions :
- Backup rom
- All wipes
- Flash kitkat baseband
- Flash rom zip
- Get through the aroma installer steps
But then, when it asked to reboot, the phone just shut down.
Now it won't turn on. All I have is a quick look at the LG boot logo, and then the screen goes all black (blacklit is still on) again.
All I managed to do so far is maintaining the LG boot logo a bit longer on screen by alternatively pressing volume + or - at random times.
I can't access recovery or download mode anymore.
Plugging the phone will only show the LG boot logo and do all the same.
The phone is no longer recognized by my computer.
When I plug it, I get 13 new windows asking me to format the device and one I can explore.
Inside, there is one folder named "Image", filled with 51,4 Mb of files...
Quite confusing.
I don't know what to do, so any help to get the phone back to work will be appreciated
Thank you in advance.
Eijo said:
Hi everyone
I may have bricked my G2. I use to have a Samsung Galaxy S which I flashed many times so I kinda know when I mess up with instructions. This time though, things look a bit more serious... Anyway, here is what happened:
I flashed the Cloudy G3 rom (1.0) for my G2 D802 32gb. Original rom was stock rooted 4.4.
I followed the instructions :
- Backup rom
- All wipes
- Flash kitkat baseband
- Flash rom zip
- Get through the aroma installer steps
But then, when it asked to reboot, the phone just shut down.
Now it won't turn on. All I have is a quick look at the LG boot logo, and then the screen goes all black (blacklit is still on) again.
All I managed to do so far is maintaining the LG boot logo a bit longer on screen by alternatively pressing volume + or - at random times.
I can't access recovery or download mode anymore.
Plugging the phone will only show the LG boot logo and do all the same.
The phone is no longer recognized by my computer.
When I plug it, I get 13 new windows asking me to format the device and one I can explore.
Inside, there is one folder named "Image", filled with 51,4 Mb of files...
Quite confusing.
I don't know what to do, so any help to get the phone back to work will be appreciated
Thank you in advance.
Click to expand...
Click to collapse
same here after flashing the wrong kernel, and tried with the good one using fastboot....
please help!
darkflyer1983 said:
same here after flashing the wrong kernel, and tried with the good one using fastboot....
please help!
Click to expand...
Click to collapse
At least I'm not alone :laugh:
I found this thread but haven't tried yet. Don't know if the problem is similar.
I really hope the phone isn't dead, it's almost brand new
This is exactly what I have . The main problem is we can not see phone partitions. Always the alarm "can not access " or "format" !Waiting for some body to help restaure our LG G2.
3205
Are you still under warranty. If you can't get into download mode that means that LG won't be able to either. You could process a return directly from LG.
Problem solved ...
Somehow I did manage to hard reset (vol - & power, wait for LG logo, release and then press vol - & power again) and then access recovery mode, so I did restore my backup (which had been renamed to ... 1970-05-01 ! lol) and my G2 is now back to life.
Weirdest thing ever... Kinda worried about flashing it again now !
Thing to remember : always have a backup file.
You are lucky man! I've done it but nothing after. I can access to hard reset but when I push power button the screen goes black as before ....
Is it actually in "Download Mode"?
GeneralMills777 said:
Are you still under warranty. If you can't get into download mode that means that LG won't be able to either. You could process a return directly from LG.
Click to expand...
Click to collapse
So, if my G2 shows "Download Mode" on the screen with the little white dots, but it's not recognized by Windows 7, Ubuntu, or Knoppix, and is for all intents and purposes, non-responsive, does anyone know if it's actually in "Download Mode"?
Eijo said:
Somehow I did manage to hard reset (vol - & power, wait for LG logo, release and then press vol - & power again) and then access recovery mode, so I did restore my backup (which had been renamed to ... 1970-05-01 ! lol) and my G2 is now back to life.
Weirdest thing ever... Kinda worried about flashing it again now !
Thing to remember : always have a backup file.
Click to expand...
Click to collapse
Peperepe said:
You are lucky man! I've done it but nothing after. I can access to hard reset but when I push power button the screen goes black as before ....
Click to expand...
Click to collapse
In my case, it just stuck on the same screen. Nothing moves.
honest1212 said:
In my case, it just stuck on the same screen. Nothing moves.
Click to expand...
Click to collapse
same problem here:
+ Download mode with some blue dot and nothing move, PC has no usb connection detected
+ Stuck on the LG logo screen with normal boot
+ NO recovery
+ it does FACTORY RESET but keep processing and nothing happen
Helped me, too.
Eijo said:
Hi everyone
I may have bricked my G2. I use to have a Samsung Galaxy S which I flashed many times so I kinda know when I mess up with instructions. This time though, things look a bit more serious... Anyway, here is what happened:
I flashed the Cloudy G3 rom (1.0) for my G2 D802 32gb. Original rom was stock rooted 4.4.
I followed the instructions :
- Backup rom
- All wipes
- Flash kitkat baseband
- Flash rom zip
- Get through the aroma installer steps
But then, when it asked to reboot, the phone just shut down.
Now it won't turn on. All I have is a quick look at the LG boot logo, and then the screen goes all black (blacklit is still on) again.
All I managed to do so far is maintaining the LG boot logo a bit longer on screen by alternatively pressing volume + or - at random times.
I can't access recovery or download mode anymore.
Plugging the phone will only show the LG boot logo and do all the same.
The phone is no longer recognized by my computer.
When I plug it, I get 13 new windows asking me to format the device and one I can explore.
Inside, there is one folder named "Image", filled with 51,4 Mb of files...
Quite confusing.
I don't know what to do, so any help to get the phone back to work will be appreciated
Thank you in advance.
Click to expand...
Click to collapse
hi dude , i had the same issue , and i lost my g2 cause of it , please dont mess with the partitions , to all of you please dont delete the partitions , just turn off your phone , press volume up and push usb cable you ll get into download mode , from there yo can go back to stock by the .tot flashing method or kdz but dont mess with partitions , i deleted partitions and my phone wad totally dead , no one could repair it
Something happened to me today...
Sent from my LG-D802 using XDA Free mobile app

[Q] Stuck on Bootscreen after flashing CWM (D802, 6.0.4.7)!

Hi there!
So I rooted my LG G2 (D802, 4.4.2, Stock, used ioroot) yesterday.
I intend(ed) to flash the Optimus G3 Rom, in the start post they recommended to flash cmw/twrp via "Simple Tool 3.2" (http://forum.xda-developers.com/showthread.php?t=2633941). After doing so (I used the automated version, not the manual one) I got STUCK ON THE BOOTSCREEN. There is a notification popping up for a few seconds in the left upper corner which lists several errors occurring:
BOOT CERTIFICATION VERIFY
SECURE BOOTING ERROR;
CAUSE: BOOTCERTIFICATION VERIFY
along with the following numbers listed from top to bottom: 710, 760, 810, 860, 910, 960 (I just noticed, the numbers can vary, but always follow the same pattern...)
after this message, the screen fades to black, I think it it is still running though, since it takes more than 10 seconds to reboot the phone by pressing the power button. I still have access to the button down/power button combo which leads to a factory reset setting, but it doesnt do anything for me since I still get stuck at the lg boot screen.
I
Atm I dont what to do! Enter download mode and flash something? I'm seriously kind lost here. So, thank you for your help!
Cheers
You flashed a custom recovery version thad doesin't match you phone ( example you flashed D801 recovery on D802 phone )
Just search in Q/A and you find the solution to fix it. Be calm , if you phone is booting - you can fix it
If you are lazy , i searched it for you. http://forum.xda-developers.com/showthread.php?t=2694530
harkis123 said:
You flashed a custom recovery version thad doesin't match you phone ( example you flashed D801 recovery on D802 phone )
Just search in Q/A and you find the solution to fix it. Be calm , if you phone is booting - you can fix it
If you are lazy , i searched it for you. http://forum.xda-developers.com/showthread.php?t=2694530
Click to expand...
Click to collapse
Thanks a ton!! Finally I can put a name on the problem (bricking...)- Ironically I never mangaged to get there in 3years of samsung flashing but got there within 15mins of flashing on the LG G2. I guess it's true what they say about samsung devices, as hard to brick as a brick...
I'll report back if it worked...
Weeell, as it turns out my phone isn't recognized by my pc (Win 7) anymore...I literally can't do anything. Any hints?
I can use the Tool, but it's always trying to connect to my phone without success. But when I connect my phone to the computer it opens a dropbox window (import photos) and several windows partitions, which it tells me to format...
thechillerdewd said:
Weeell, as it turns out my phone isn't recognized by my pc (Win 7) anymore...I literally can't do anything. Any hints?
I can use the Tool, but it's always trying to connect to my phone without success. But when I connect my phone to the computer it opens a dropbox window (import photos) and several windows partitions, which it tells me to format...
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2687768

[Q] Flashed wrong kernel!!!

i Was trying to get rid of the hissing noise on my
Lg g2 D802
i had TWRP installed
I read in a trhead that flashing the dorimanx kernel should fix that problem.
So i tried flash it, but instead of flashing the D802 i flashed the D800, i know i'm an idiot :/
I had a backup stock kernel but i think that's a wrong one too, again i'm an idiot
Now my phone boots into a black screen within the left top corner:
[2800] Fastboot mode started
[2850] udc_start()
i cannot boot into twrp anymore, it's basically bricked.
Can anyone help me recover my phone? i loved that thing, you will be my hero.
i promise when this is resolved i will never mess around with roms and kernels ever agian, i'm freaking out
henny420 said:
i Was trying to get rid of the hissing noise on my
Lg g2 D802
i had TWRP installed
I read in a trhead that flashing the dorimanx kernel should fix that problem.
So i tried flash it, but instead of flashing the D802 i flashed the D800, i know i'm an idiot :/
I had a backup stock kernel but i think that's a wrong one too, again i'm an idiot
Now my phone boots into a black screen within the left top corner:
[2800] Fastboot mode started
[2850] udc_start()
i cannot boot into twrp anymore, it's basically bricked.
Can anyone help me recover my phone? i loved that thing, you will be my hero.
i promise when this is resolved i will never mess around with roms and kernels ever agian, i'm freaking out
Click to expand...
Click to collapse
Try to flash back to stock with kdz, as far as I am hearing this you kinda soft bricked it but not hard so it's still recoverable, you could also maybe try to flash your recovery back with fastboot since your in fastboot mode but I never tried that so I suggest you to go back to stock with kdz flashing
ye try enter download mode and follow this (use search) i think its volum up and connect usb to pc
http://forum.xda-developers.com/showthread.php?t=2432476
wulsic said:
Try to flash back to stock with kdz, as far as I am hearing this you kinda soft bricked it but not hard so it's still recoverable, you could also maybe try to flash your recovery back with fastboot since your in fastboot mode but I never tried that so I suggest you to go back to stock with kdz flashing
Click to expand...
Click to collapse
thank you for your response, but i am kind of noob and have no idea how to do that correctly, could you link something or explain it?
henny420 said:
thank you for your response, but i am kind of noob and have no idea how to do that correctly, could you link something or explain it?
Click to expand...
Click to collapse
Try the link above mentioned by Overclocked
OverClockeD_GR said:
ye try enter download mode and follow this (use search) i think its volum up and connect usb to pc
http://forum.xda-developers.com/showthread.php?t=2432476
Click to expand...
Click to collapse
Thank you for your reply, i tried to get into download mode, but failed every time, i can only press the power button for 5 sec and the Lg logo apears, then i get the same screen.
did this way?
Your phone must be turned off before starting the steps from this guide.
So, press power button and select “power off”.
Then, press the volume up button on your LG G2.
While you are holding the volume up button, plug in your phone’s USB cable.
Keep pressing the Volume up button until the download mode is being displayed.
Now the phone will install some drivers – it should take around 10 minutes to complete; the best will be to let your device install the mentioned drivers.
OverClockeD_GR said:
did this way?
Your phone must be turned off before starting the steps from this guide.
So, press power button and select “power off”.
Then, press the volume up button on your LG G2.
While you are holding the volume up button, plug in your phone’s USB cable.
Keep pressing the Volume up button until the download mode is being displayed.
Now the phone will install some drivers – it should take around 10 minutes to complete; the best will be to let your device install the mentioned drivers.
Click to expand...
Click to collapse
the problem is, i can't turn it off (very weird) it instantly gives me the logo for 1sec and turns back to the same screen.
you can also try this.
http://forum.xda-developers.com/showthread.php?t=2477595
just use search mate like i do now... its soft brick i think relax and you will find it many had same prob before
henny420 said:
i Was trying to get rid of the hissing noise on my
Lg g2 D802
i had TWRP installed
I read in a trhead that flashing the dorimanx kernel should fix that problem.
So i tried flash it, but instead of flashing the D802 i flashed the D800, i know i'm an idiot :/
I had a backup stock kernel but i think that's a wrong one too, again i'm an idiot
Now my phone boots into a black screen within the left top corner:
[2800] Fastboot mode started
[2850] udc_start()
i cannot boot into twrp anymore, it's basically bricked.
Can anyone help me recover my phone? i loved that thing, you will be my hero.
i promise when this is resolved i will never mess around with roms and kernels ever agian, i'm freaking out
Click to expand...
Click to collapse
I did the same thing today by accident. I still can boot into recovery tho, TWRP. Copied the correct kernel file via OTG but it just reboots the recovery and doesn't install the kernel. Have you find any solutions?
EDIT: I actually managed to flash the right kernel and the problem is now fixed. Check everything before flashing something guys, caution

LG G2 Might be bricked, not sure.

Hello, cutting to the chase
Model: LG G2 D802
Story time: I tried to install ressurection remix rom through the sideload, after fully wiping my phone ( Wiped system, data, yada yada ) it showed some kind of an error about SU not installing properly, I thought well if I'll reboot TWRP will automaticly install SU for me, so when I tried to reboot it showed that No OS is installed, I thought it's a simple bug so I'll reboot to recovery again to check and bam. Nothing works.
+ Can't boot into recovery ( Tried volume down + power button ) LG Logo shows up and goes blank again ( Note that the screen doesn't turn off, just stays black, after holding it for a couple of seconds I can see screen going off completely but can't turn it on)
+ Can't turn it on normally.
+ Can't boot into download mode.
+After plugging it into an USB it mounts a D lettered drive with 63MB stuff in a folder called image with *.mdt files, modem files( I can screen it if it's important )
I'm clueless, never happened to me even though I flashed a lot of roms, I think I bricked it. Help?
UPDATE: I managed to quickly release Volume Down And Power buttons when LG appeared for half a second and hold it again, succesfully booted into TWRP. I haven't bricked it I think. Will tell how it goes <3
Hey man, how'd it go?
I'm in exactly the same situation as yours, can boot into twrp but nothing else works, i fear of the qhsusb_bulk brick but these people don't even seem to have recovery.
Any suggestions? Go back to stock? How?
Argus137 said:
UPDATE: I managed to quickly release Volume Down And Power buttons when LG appeared for half a second and hold it again, succesfully booted into TWRP. I haven't bricked it I think. Will tell how it goes <3
Click to expand...
Click to collapse
How did it go!? I'm in a similar situation (but can boot into download-mode). Would love to get back to twrp, since I want to give it a try to flash another cm (stable). Thanks for sharing your experience...
If its picking up bulk mode normally its hard bricked there is a guide for restore nearly all g2s from hard brick having done it myself included 1st time took me a week to get back up but. Now i prob take about 45 min just cause i aint had one in a while
TheMadScientist420 said:
If its picking up bulk mode normally its hard bricked there is a guide for restore nearly all g2s from hard brick having done it myself included 1st time took me a week to get back up but. Now i prob take about 45 min just cause i aint had one in a while
Click to expand...
Click to collapse
Hey there, can you specify what you did exactly or where to find!? Do you mean something like this? (can't post outside links, in XDA-forum, title is "LG G2 is UNBRICKABLE NOW! [FIX REAL HARD BRICK]") Thanks for help...
Yes thats it. Lol i still got the files on my pc for my g2 i keep the whe setup cause im on the g3 now i just check in the g2 forums cause i had mine for 2 years and modded the crap outa it but yea i keep all the files on hand so if anything ever happens i can fix it almost on the fly now
Well so what happened to me that I managed to get inside the TWRP. When it lighed it up for a second I quickly released and held again that got me inside magically. So then I just transfered new rom and tried to install again. Sadly I didin't see that the ROM Im trying to install requires bump TWRP and I bricked my phone again. Though I entered download mode and flashed the stock rom through LG G2 flasher.
heres a video i made, how to go into recovery. for those that cant get in to twrp.
https://www.youtube.com/watch?v=jPUTImVEHqc

Categories

Resources