I installed bcmon only to get the following screen.
fireware model: not detected
installed tools version: 0
installed fx version: 0
I am currently running the X-Note ROM v3.0, which has the latest AEL kernel v5.2.
Using a SM-N910T.
Does the galaxy note 4 simply not contain the required Broadcom chipset or is there another method to get to monitor mode, assuming it is, at all, possible?
Related
My phones' Info:
Device name: GALAXY y (GT-S5360)
Android Version: 4.1.1
Baseband version: S5360DXKK2
Kernel Version: 2.6.35.7 Merruk [email protected]
Build number: JELLYBLASTV-3.0.3 by Avijit
whenever i connect my phone to my computer my battery saver icon disappears. Can you help me how to fix it?
First of all, change the rom. Its a banned rom and the xda community can't help for that rom.
Secondly it's not 4.1.1. Out SGY is struggling to get 4.0 to run properly how could you gets JB.
Moral: Change rom. There are many good ones out there in the development section. Have fun
Hi everyone;
I racently installed Omega ROM v22 4.4.2 for my Galaxy S4 I9500.(I had the WanamLite but developer stopped supporting it.) I want to overclock it so I did a little research and found Ktoonsez Kernel. I downloaded the TW version of it and flashed. I cleaned dalvik and cache. When I tried to open KTweaker it opened succesfully. But I couldnt get into CPU settings. The app just freezes and stops itself. I looked up in the system information and the kernel hasn't changed! It still says [email protected] #1. What have I done wrong? I have a nandroid backup.
Thx..
Phone: GT-I9500
Recovery: TWRP
Rom: Omega v22 - XXUFNE7
Version : 4.4.2 KitKat
Kernel Showing Up: 3.4.5
[email protected] #1
It's probably because its a kernel for the i9505 or am I missing the thread for the i9500?
Hello everyone
i have G900F which was running stock rooted ANG2 4.4.2 rom.
i installed CWM recovery then Fusion V2 Kernel and Fusion last rom and PA gapps
my problem is:
i cant open the mobile data (phone call and sms are fine)
there is an explanation marks on the signal and wifi icons
in the about device it show that my baseband and bootloader are ANG2 (which is 4.4.2) while i am runinng 5.0.2 CFW.
what should i do??
Thanks
Hello, I installed the latest version via recovery (this is the file used: BlissPop-v4.0.3-matisse-UNOFFICIAL-20151008-1838.zip ) but I have two problems:
1- ota reports new update but after downloaded and installed the version that is not updated is 2015100804
2- if Chrome closed and reopened hides the navigation bar and the navigation is impossible.
3- The camera does not work
I have a tab 4 10.1 lte europe T535
I apologize for the English
Change default storage Path (BlisspopRom)
Is it possible to change the default saving path in The Blisspop Rom??
have the phone with the following specs
Samsung Galaxy A5 (SM-A500F) (Dual Sim)
Android Version (5.0.2)
Qualcomm 4G
Fully rooted
Installed Twrp Recovery
Now i read a guide at xda developers in how to Enable all LTE bands for qualcomm devices.
http://forum.xda-developers.com/galaxy-s5/general/how-to-add-rf-lte-frequency-bands-to-t2886059
the guide sasy it will only work on custom rom and custom kernel. where can i get a custom kernel for my device? (i searched xda,there was one but had loads of bugs)
Additional Info: i am going to install/Flash custom rom CM 12.1 (ANDROID 5.1.1) from here
http://forum.xda-developers.com/samsung-a-series/development/rom-cyanogenmod12-1-temasek-unofficial-t3163722
Also How can i access advance usb settings? I want to change AP TO CP
Mod edit: Thread closed as duplicate. Create a thread or post only once.